Trying 0.0.0.0... Connected to 0. Escape character is '^]'. U-Boot SPL 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) Initializing DDR....using raw memory timing SPI boot Trying to boot from SPI U-Boot 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) SoC: LS1028A Rev1.0 (0x870b0110) Clock Configuration: CPU0(A72):1300 MHz CPU1(A72):1300 MHz Bus: 400 MHz DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 34004010 00000030 00000000 00000000 00000010: 00000000 008f0000 0030c000 00000000 00000020: 06200000 00002580 00000000 00019016 00000030: 00000000 00000048 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000103 00000000 100e7026 00000000 00000070: bb580000 00020000 Model: Kontron SMARC-sAL28 Board Hardware Variant: Single PHY (3) RCW: sl28-3-11_q.bin DRAM: Detected UDIMM Fixed DDR on board 3.9 GiB DDR 3.9 GiB (DDR3, 32-bit, CL=11, ECC on) Using SERDES1 Protocol: 47960 (0xbb58) PCIe1: pcie@3400000 Root Complex: no link PCIe2: pcie@3500000 Root Complex: no link CPLD: v18 WDT: Started with servicing (60s timeout) Waking secondary cores to start from fbd3c000 All (2) cores are up. MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPI Flash... SF: Detected w25q32jw with page size 256 Bytes, erase size 64 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial VPD: Using device 0x50 on I2C Bus 2 Net: eth0: enetc-0, eth2: enetc-2 Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => dhcp dhcp enetc-0 Waiting for PHY auto negotiation to complete.... done BOOTP broadcast 1 BOOTP broadcast 2 DHCP client bound to address 172.16.0.64 (255 ms) => setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 => tftp 0x82000000 514106/tftp-deploy-7i11prj6/kernel/Image tftp 0x82000000 514106/tftp-deploy-7i11prj6/kernel/Image Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.64; sending through gateway 172.16.0.254 Filename '514106/tftp-deploy-7i11prj6/kernel/Image'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################# 14.6 MiB/s done Bytes transferred = 27191808 (19eea00 hex) => tftp 0x90080000 514106/tftp-deploy-7i11prj6/ramdisk/ramdisk.cpio.gz.uboot tftp 0x90080000 514106/tftp-deploy-7i11prj6/ramdisk/ramdisk.cpio.gz.uboot Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.64; sending through gateway 172.16.0.254 Filename '514106/tftp-deploy-7i11prj6/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x90080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################## 5.6 MiB/s done Bytes transferred = 19029856 (1225f60 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 514106/tftp-deploy-7i11prj6/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb tftp 0x90000000 514106/tftp-deploy-7i11prj6/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.64; sending through gateway 172.16.0.254 Filename '514106/tftp-deploy-7i11prj6/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb'. Load address: 0x90000000 Loading: *## 8 MiB/s done Bytes transferred = 25279 (62bf hex) => setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => booti 0x82000000 0x90080000 0x90000000 booti 0x82000000 0x90080000 0x90000000 ## Loading init Ramdisk from Legacy Image at 90080000 ... Image Name: Created: 2024-11-11 14:41:14 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 19029792 Bytes = 18.1 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Using Device Tree in place at 0000000090000000, end 00000000900092be WARNING could not find node fsl,ls1028a-gpu: FDT_ERR_NOTFOUND. Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [ 0.000000] Linux version 5.10.226 (KernelCI@build-j372841-arm64-clang-17-defconfig-h84lr) (Debian clang version 17.0.6 (++20231208085813+6009708b4367-1~exp1~20231208085906.81), Debian LLD 17.0.6) #1 SMP PREEMPT Mon Nov 11 14:12:28 UTC 2024 [ 0.000000] Machine model: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: ns16550a0 at MMIO 0x00000000021c0500 (options '115200n8') [ 0.000000] printk: bootconsole [ns16550a0] enabled [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x20ff7fea80-0x20ff800fff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000020ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fbdfffff] [ 0.000000] node 0: [mem 0x0000002080000000-0x00000020ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] cma: Reserved 32 MiB at 0x00000000f9c00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv0.2 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] percpu: Embedded 23 pages/cpu s56856 r8192 d29160 u94208 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: Spectre-v3a [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: Spectre-v4 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: detected: ARM erratum 1742098 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1015296 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] software IO TLB: mapped [mem 0x00000000f5c00000-0x00000000f9c00000] (64MB) <6>[ 0.000000] Memory: 3902128K/4126720K available (14784K kernel code, 2746K rwdata, 7300K rodata, 1600K init, 528K bss, 191824K reserved, 32768K cma-reserved) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=2. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode <6>[ 0.000000] GICv3: 256 SPIs implemented <6>[ 0.000000] GICv3: 0 Extended SPIs implemented <6>[ 0.000000] GICv3: Distributor has no Range Selector support <6>[ 0.000000] GICv3: 16 PPIs implemented <6>[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006040000 <6>[ 0.000000] ITS [mem 0x06020000-0x0603ffff] <6>[ 0.000000] ITS@0x0000000006020000: allocated 65536 Devices @2080080000 (flat, esz 8, psz 64K, shr 0) <6>[ 0.000000] ITS: using cache flushing for cmd queue <6>[ 0.000000] GICv3: using LPI property table @0x0000002080030000 <6>[ 0.000000] GIC: using cache flushing for LPI property table <6>[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000002080040000 <6>[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns <6>[ 0.000002] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns <6>[ 0.008686] Console: colour dummy device 80x25 <6>[ 0.013472] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) <6>[ 0.024191] pid_max: default: 32768 minimum: 301 <6>[ 0.029147] LSM: Security Framework initializing <6>[ 0.034116] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.041871] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.050937] rcu: Hierarchical SRCU implementation. <6>[ 0.056175] Platform MSI: gic-its@6020000 domain created <6>[ 0.061869] PCI/MSI: /interrupt-controller@6000000/gic-its@6020000 domain created <6>[ 0.069724] fsl-mc MSI: gic-its@6020000 domain created <6>[ 0.075804] EFI services will not be available. <6>[ 0.080739] smp: Bringing up secondary CPUs ... <6>[ 0.085859] Detected PIPT I-cache on CPU1 <6>[ 0.085876] GICv3: CPU1: found redistributor 1 region 0:0x0000000006060000 <6>[ 0.085884] GICv3: CPU1: using allocated LPI pending table @0x0000002080050000 <6>[ 0.085907] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] <6>[ 0.085960] smp: Brought up 1 node, 2 CPUs <6>[ 0.116274] SMP: Total of 2 processors activated. <6>[ 0.121285] CPU features: detected: 32-bit EL0 Support <6>[ 0.126743] CPU features: detected: CRC32 instructions <6>[ 0.132195] CPU features: detected: 32-bit EL1 Support <6>[ 0.148178] CPU: All CPU(s) started at EL2 <6>[ 0.152599] alternatives: patching kernel code <6>[ 0.158137] devtmpfs: initialized <4>[ 0.163928] KASLR disabled due to lack of seed <6>[ 0.168793] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.178903] futex hash table entries: 512 (order: 3, 32768 bytes, linear) <6>[ 0.186588] pinctrl core: initialized pinctrl subsystem <6>[ 0.192749] DMI not present or invalid. <6>[ 0.197248] NET: Registered protocol family 16 <6>[ 0.202887] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.210385] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.218491] audit: initializing netlink subsys (disabled) <5>[ 0.224302] audit: type=2000 audit(0.144:1): state=initialized audit_enabled=0 res=1 <6>[ 0.224838] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.232390] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.238873] cpuidle: using governor menu <6>[ 0.250045] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.257185] ASID allocator initialised with 65536 entries <6>[ 0.263437] Serial: AMBA PL011 UART driver <6>[ 0.270633] Machine: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier <6>[ 0.278281] SoC family: QorIQ LS1028A <6>[ 0.282234] SoC ID: svr:0x870b0110, Revision: 1.0 <6>[ 0.299711] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.306749] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.313783] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.320813] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.329925] ACPI: Interpreter disabled. <6>[ 0.334951] iommu: Default domain type: Translated <6>[ 0.340271] vgaarb: loaded <5>[ 0.343416] SCSI subsystem initialized <6>[ 0.347739] usbcore: registered new interface driver usbfs <6>[ 0.353553] usbcore: registered new interface driver hub <6>[ 0.359199] usbcore: registered new device driver usb <6>[ 0.364824] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.372635] i2c i2c-0: IMX I2C adapter registered <6>[ 0.377815] imx-i2c 2030000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.385483] i2c i2c-1: IMX I2C adapter registered <6>[ 0.390575] imx-i2c 2040000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.398307] i2c i2c-2: IMX I2C adapter registered <6>[ 0.403585] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.408871] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.418363] PTP clock support registered <6>[ 0.422663] EDAC MC: Ver: 3.0.0 <6>[ 0.426830] FPGA manager framework <6>[ 0.430565] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.437368] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.443885] VFS: Disk quotas dquot_6.6.0 <6>[ 0.448139] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 0.455445] pnp: PnP ACPI: disabled <6>[ 0.462408] NET: Registered protocol family 2 <6>[ 0.467369] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 0.476530] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear) <6>[ 0.485453] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) <6>[ 0.493791] TCP bind hash table entries: 32768 (order: 7, 524288 bytes, linear) <6>[ 0.501792] TCP: Hash tables configured (established 32768 bind 32768) <6>[ 0.508752] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.515805] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.523363] NET: Registered protocol family 1 <6>[ 0.528325] RPC: Registered named UNIX socket transport module. <6>[ 0.534570] RPC: Registered udp transport module. <6>[ 0.539581] RPC: Registered tcp transport module. <6>[ 0.544594] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.551363] PCI: CLS 0 bytes, default 64 <6>[ 0.555666] Unpacking initramfs... <6>[ 1.229340] Freeing initrd memory: 18576K <6>[ 1.233976] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available <6>[ 1.242712] kvm [1]: IPA Size Limit: 44 bits <6>[ 1.247950] kvm [1]: GICv3: no GICV resource entry <6>[ 1.253052] kvm [1]: disabling GICv2 emulation <6>[ 1.257811] kvm [1]: GIC system register CPU interface enabled <6>[ 1.263989] kvm [1]: vgic interrupt IRQ9 <6>[ 1.268288] kvm [1]: Hyp mode initialized successfully <5>[ 1.274696] Initialise system trusted keyrings <6>[ 1.279535] workingset: timestamp_bits=42 max_order=20 bucket_order=0 <6>[ 1.289438] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.295991] NFS: Registering the id_resolver key type <5>[ 1.301374] Key type id_resolver registered <5>[ 1.305859] Key type id_legacy registered <6>[ 1.310218] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 1.317250] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 1.325069] 9p: Installing v9fs 9p2000 file system support <5>[ 1.359706] Key type asymmetric registered <5>[ 1.364107] Asymmetric key parser 'x509' registered <6>[ 1.369313] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 1.377046] io scheduler mq-deadline registered <6>[ 1.381885] io scheduler kyber registered <4>[ 1.392000] EINJ: ACPI disabled. <6>[ 1.403162] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 1.411051] printk: console [ttyS0] disabled <6>[ 1.415677] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 23, base_baud = 12500000) is a 16550A <6>[ 1.424847] printk: console [ttyS0] enabled <6>[ 1.424847] printk: console [ttyS0] enabled <6>[ 1.433787] printk: bootconsole [ns16550a0] disabled <6>[ 1.433787] printk: bootconsole [ns16550a0] disabled <6>[ 1.444626] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 23, base_baud = 12500000) is a 16550A <6>[ 1.453997] SuperH (H)SCI(F) driver initialized <6>[ 1.459099] msm_serial: driver initialized <6>[ 1.467041] loop: module loaded <6>[ 1.475054] megasas: 07.714.04.00-rc1 <6>[ 1.481197] spi-nor spi0.0: w25q32jwm (4096 Kbytes) <5>[ 1.494925] 8 fixed-partitions partitions found on MTD device 20c0000.spi <5>[ 1.502013] Creating 8 MTD partitions on \"20c0000.spi\": <5>[ 1.507534] 0x000000000000-0x000000010000 : \"rcw\" <5>[ 1.513803] 0x000000010000-0x000000100000 : \"failsafe bootloader\" <5>[ 1.521761] 0x000000100000-0x000000140000 : \"failsafe DP firmware\" <5>[ 1.529745] 0x000000140000-0x0000001e0000 : \"failsafe trusted firmware\" <5>[ 1.537747] 0x0000001e0000-0x000000200000 : \"reserved\" <5>[ 1.545752] 0x000000200000-0x000000210000 : \"configuration store\" <5>[ 1.553751] 0x000000210000-0x0000003e0000 : \"bootloader\" <5>[ 1.561755] 0x0000003e0000-0x000000400000 : \"bootloader environment\" <6>[ 1.571547] tun: Universal TUN/TAP device driver, 1.6 <6>[ 1.577340] thunder_xcv, ver 1.0 <6>[ 1.580862] thunder_bgx, ver 1.0 <6>[ 1.584379] nicpf, ver 1.0 <6>[ 1.588057] hclge is initializing <6>[ 1.591657] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 1.599170] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 1.604787] e1000: Intel(R) PRO/1000 Network Driver <6>[ 1.609944] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 1.615991] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 1.621235] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 1.627453] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 1.633131] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.638996] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 1.645547] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 1.651939] sky2: driver version 1.30 <6>[ 1.656492] VFIO - User Level meta-driver version: 0.3 <6>[ 1.663028] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 1.669859] ehci-pci: EHCI PCI platform driver <6>[ 1.674597] ehci-platform: EHCI generic platform driver <6>[ 1.680179] ehci-orion: EHCI orion driver <6>[ 1.684521] ehci-exynos: EHCI Exynos driver <6>[ 1.689031] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 1.695507] ohci-pci: OHCI PCI platform driver <6>[ 1.700245] ohci-platform: OHCI generic platform driver <6>[ 1.705816] ohci-exynos: OHCI Exynos driver <6>[ 1.710556] usbcore: registered new interface driver usb-storage <6>[ 1.718418] i2c /dev entries driver <6>[ 1.724987] sp805-wdt c000000.watchdog: registration successful <6>[ 1.731303] sp805-wdt c010000.watchdog: registration successful <6>[ 1.738708] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver <6>[ 1.747380] sdhci: Secure Digital Host Controller Interface driver <6>[ 1.753859] sdhci: Copyright(c) Pierre Ossman <6>[ 1.758823] Synopsys Designware Multimedia Card Interface Driver <6>[ 1.765703] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 1.772589] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 1.779743] usbcore: registered new interface driver usbhid <6>[ 1.785604] usbhid: USB HID core driver <6>[ 1.792492] NET: Registered protocol family 17 <6>[ 1.797324] 9pnet: Installing 9P2000 support <5>[ 1.801909] Key type dns_resolver registered <6>[ 1.806657] registered taskstats version 1 <5>[ 1.811034] Loading compiled-in X.509 certificates <4>[ 1.816179] <4>[ 1.817941] ******************************************************************** <4>[ 1.825626] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** <4>[ 1.833310] ** ** <4>[ 1.840995] ** WRITEABLE clk DebugFS SUPPORT HAS BEEN ENABLED IN THIS KERNEL ** <4>[ 1.848679] ** ** <4>[ 1.856364] ** This means that this kernel is built to expose clk operations ** <4>[ 1.864049] ** such as parent or rate setting, enabling, disabling, etc. ** <4>[ 1.871742] ** to userspace, which may compromise security on your system. ** <4>[ 1.879428] ** ** <4>[ 1.887111] ** If you see this message and you are not debugging the ** <4>[ 1.894795] ** kernel, report this immediately to your vendor! ** <4>[ 1.902477] ** ** <4>[ 1.910161] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** <4>[ 1.917845] ******************************************************************** <6>[ 1.937515] input: buttons0 as /devices/platform/buttons0/input/input0 <6>[ 14.217428] clk: Disabling unused clocks <6>[ 14.221762] ALSA device list: <6>[ 14.225023] No soundcards found. <6>[ 14.230606] Freeing unused kernel memory: 1600K <6>[ 14.235856] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 14.295468] udevd[109]: starting version 3.2.9 <5>[ 14.300663] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 14.307570] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 14.314334] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 14.323807] udevd[109]: specified user 'tss' unknown <27>[ 14.329193] udevd[109]: specified group 'tss' unknown <30>[ 14.335388] udevd[110]: starting eudev-3.2.9 <4>[ 14.523681] at24 0-0050: supply vcc not found, using dummy regulator <4>[ 14.552143] wm8904 2-001a: supply DCVDD not found, using dummy regulator <4>[ 14.562404] wm8904 2-001a: supply DBVDD not found, using dummy regulator <4>[ 14.569492] wm8904 2-001a: supply AVDD not found, using dummy regulator <4>[ 14.576667] rtc-rv8803 0-0032: Voltage low, temperature compensation stopped. <4>[ 14.577805] wm8904 2-001a: supply CPVDD not found, using dummy regulator <4>[ 14.585528] rtc-rv8803 0-0032: Voltage low, data loss detected. <4>[ 14.591182] wm8904 2-001a: supply MICVDD not found, using dummy regulator <6>[ 14.604910] at24 0-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 14.613895] at24 1-0057: supply vcc not found, using dummy regulator <4>[ 14.623363] rtc-rv8803 0-0032: Voltage low, data is invalid. <6>[ 14.629826] rtc-rv8803 0-0032: registered as rtc0 <6>[ 14.635349] at24 1-0057: 8192 byte 24c64 EEPROM, writable, 32 bytes/write <6>[ 14.642751] wm8904 2-001a: revision A <4>[ 14.646984] at24 2-0050: supply vcc not found, using dummy regulator <4>[ 14.654767] rtc-rv8803 0-0032: Voltage low, data is invalid. <6>[ 14.662213] sl28cpld-wdt 2000000.i2c:sl28cpld@4a:watchdog@4: initial timeout 6 sec <3>[ 14.670834] rtc-rv8803 0-0032: hctosys: unable to read the hardware clock <6>[ 14.678764] at24 2-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <6>[ 14.722789] caam 8000000.crypto: Entropy delay = 3200 <5>[ 14.734820] arm-smmu 5000000.iommu: probing hardware configuration... <5>[ 14.741585] arm-smmu 5000000.iommu: SMMUv2 with: <5>[ 14.750307] arm-smmu 5000000.iommu: stage 1 translation <5>[ 14.756661] arm-smmu 5000000.iommu: stage 2 translation <5>[ 14.763322] arm-smmu 5000000.iommu: nested translation <5>[ 14.769522] arm-smmu 5000000.iommu: stream matching with 128 register groups <5>[ 14.777021] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) <5>[ 14.785102] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 <5>[ 14.792883] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA <6>[ 14.796724] caam 8000000.crypto: Instantiated RNG4 SH0 <5>[ 14.800593] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA <6>[ 14.813523] pci-host-generic 1f0000000.pcie: host bridge /soc/pcie@1f0000000 ranges: <6>[ 14.822993] pci-host-generic 1f0000000.pcie: MEM 0x01f8000000..0x01f815ffff -> 0x0000000000 <6>[ 14.831362] caam 8000000.crypto: Instantiated RNG4 SH1 <6>[ 14.832655] pci-host-generic 1f0000000.pcie: MEM 0x01f8160000..0x01f81cffff -> 0x0000000000 <6>[ 14.846849] pci-host-generic 1f0000000.pcie: MEM 0x01f81d0000..0x01f81effff -> 0x0000000000 <6>[ 14.847562] caam 8000000.crypto: device ID = 0x0a12070000000000 (Era 10) <6>[ 14.856072] pci-host-generic 1f0000000.pcie: MEM 0x01f81f0000..0x01f820ffff -> 0x0000000000 <6>[ 14.863090] caam 8000000.crypto: job rings = 4, qi = 0 <6>[ 14.872086] pci-host-generic 1f0000000.pcie: MEM 0x01f8210000..0x01f822ffff -> 0x0000000000 <6>[ 14.892796] pci-host-generic 1f0000000.pcie: MEM 0x01f8230000..0x01f824ffff -> 0x0000000000 <6>[ 14.902974] pci-host-generic 1f0000000.pcie: MEM 0x01fc000000..0x01fc3fffff -> 0x0000000000 <6>[ 14.912144] pci-host-generic 1f0000000.pcie: ECAM at [mem 0x1f0000000-0x1f00fffff] for [bus 00] <6>[ 14.912659] caam_jr 8010000.jr: Adding to iommu group 0 <6>[ 14.921250] pci-host-generic 1f0000000.pcie: PCI host bridge to bus 0000:00 <6>[ 14.927922] caam algorithms registered in /proc/crypto <6>[ 14.933935] pci_bus 0000:00: root bus resource [bus 00] <6>[ 14.933941] pci_bus 0000:00: root bus resource [mem 0x1f8000000-0x1f815ffff] (bus address [0x00000000-0x0015ffff]) <6>[ 14.933947] pci_bus 0000:00: root bus resource [mem 0x1f8160000-0x1f81cffff pref] (bus address [0x00000000-0x0006ffff]) <6>[ 14.940416] caam 8000000.crypto: registering rng-caam <6>[ 14.944869] pci_bus 0000:00: root bus resource [mem 0x1f81d0000-0x1f81effff] (bus address [0x00000000-0x0001ffff]) <6>[ 14.944873] pci_bus 0000:00: root bus resource [mem 0x1f81f0000-0x1f820ffff pref] (bus address [0x00000000-0x0001ffff]) <6>[ 14.944877] pci_bus 0000:00: root bus resource [mem 0x1f8210000-0x1f822ffff] (bus address [0x00000000-0x0001ffff]) <6>[ 14.966887] caam_jr 8020000.jr: Adding to iommu group 1 <6>[ 14.971985] pci_bus 0000:00: root bus resource [mem 0x1f8230000-0x1f824ffff pref] (bus address [0x00000000-0x0001ffff]) <6>[ 14.983159] caam_jr 8030000.jr: Adding to iommu group 2 <6>[ 14.993733] pci_bus 0000:00: root bus resource [mem 0x1fc000000-0x1fc3fffff] (bus address [0x00000000-0x003fffff]) <6>[ 14.993757] pci 0000:00:00.0: [1957:e100] type 00 class 0x020001 <6>[ 15.005003] caam_jr 8040000.jr: Adding to iommu group 3 <6>[ 15.010002] pci 0000:00:00.0: BAR 0: [mem 0x1f8000000-0x1f803ffff 64bit] (from Enhanced Allocation, properties 0x0) <5>[ 15.037223] random: crng init done <6>[ 15.043505] pci 0000:00:00.0: BAR 2: [mem 0x1f8160000-0x1f816ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 15.043511] pci 0000:00:00.0: VF BAR 0: [mem 0x1f81d0000-0x1f81dffff 64bit] (from Enhanced Allocation, properties 0x4) done<5>[ 15.049452] random: 2 urandom warning(s) missed due to ratelimiting <6>[ 15.059933] pci 0000:00:00.0: VF BAR 2: [mem 0x1f81f0000-0x1f81fffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 15.103969] pci 0000:00:00.0: PME# supported from D0 D3hot <6>[ 15.109928] pci 0000:00:00.0: VF(n) BAR0 space: [mem 0x1f81d0000-0x1f81effff 64bit] (contains BAR0 for 2 VFs) Saving random se<6>[ 15.120164] pci 0000:00:00.0: VF(n) BAR2 space: [mem 0x1f81f0000-0x1f820ffff 64bit pref] (contains BAR2 for 2 VFs) ed: <6>[ 15.132416] pci 0000:00:00.1: [1957:e100] type 00 class 0x020001 OK <6>[ 15.138904] pci 0000:00:00.1: BAR 0: [mem 0x1f8040000-0x1f807ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 15.149968] pci 0000:00:00.1: BAR 2: [mem 0x1f8170000-0x1f817ffff 64bit pref] (from Enhanced Allocation, properties 0x1) Starting network<6>[ 15.161166] pci 0000:00:00.1: VF BAR 0: [mem 0x1f8210000-0x1f821ffff 64bit] (from Enhanced Allocation, properties 0x4) : <6>[ 15.173599] pci 0000:00:00.1: VF BAR 2: [mem 0x1f8230000-0x1f823ffff 64bit pref] (from Enhanced Allocation, properties 0x3) OK<6>[ 15.185201] pci 0000:00:00.1: PME# supported from D0 D3hot <6>[ 15.191125] pci 0000:00:00.1: VF(n) BAR0 space: [mem 0x1f8210000-0x1f822ffff 64bit] (contains BAR0 for 2 VFs) <6>[ 15.201355] pci 0000:00:00.1: VF(n) BAR2 space: [mem 0x1f8230000-0x1f824ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 15.212380] pci 0000:00:00.2: [1957:e100] type 00 class 0x020001 <6>[ 15.218847] pci 0000:00:00.2: BAR 0: [mem 0x1f8080000-0x1f80bffff 64bit] (from Enhanced Allocation, properties 0x0) Starting dropbea<6>[ 15.229717] pci 0000:00:00.2: BAR 2: [mem 0x1f8180000-0x1f818ffff 64bit pref] (from Enhanced Allocation, properties 0x1) r sshd: <6>[ 15.242334] pci 0000:00:00.2: PME# supported from D0 D3hot <6>[ 15.249063] pci 0000:00:00.3: [1957:ee01] type 00 class 0x088001 <6>[ 15.251482] NET: Registered protocol family 10 <6>[ 15.255521] pci 0000:00:00.3: BAR 0: [mem 0x1f8100000-0x1f811ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 15.260643] Segment Routing with IPv6 <6>[ 15.270932] pci 0000:00:00.3: BAR 2: [mem 0x1f8190000-0x1f819ffff 64bit pref] (from Enhanced Allocation, properties 0x1) OK <6>[ 15.286475] pci 0000:00:00.3: PME# supported from D0 D3hot <6>[ 15.292538] pci 0000:00:00.4: [1957:ee02] type 00 class 0x088001 <6>[ 15.298881] pci 0000:00:00.4: BAR 0: [mem 0x1f8120000-0x1f813ffff 64bit] (from Enhanced Allocation, properties 0x0) /bin/sh: <6>[ 15.309671] pci 0000:00:00.4: BAR 2: [mem 0x1f81a0000-0x1f81affff 64bit pref] (from Enhanced Allocation, properties 0x1) can't access tty<6>[ 15.321688] pci 0000:00:00.4: PME# supported from D0 D3hot ; job control tu<6>[ 15.329028] pci 0000:00:00.5: [1957:eef0] type 00 class 0x020801 rned off / # <6>[ 15.336534] pci 0000:00:00.5: BAR 0: [mem 0x1f8140000-0x1f815ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 15.348458] pci 0000:00:00.5: BAR 2: [mem 0x1f81b0000-0x1f81bffff 64bit pref] (from Enhanced Allocation, pr operties 0x1) <6>[ 15.359636] pci 0000:00:00.5: BAR 4: [mem 0x1fc000000-0x1fc3fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 15.370391] pci 0000:00:00.5: PME# supported from D0 D3hot <6>[ 15.376333] pci 0000:00:00.6: [1957:e100] type 00 class 0x020001 <6>[ 15.382672] pci 0000:00:00.6: BAR 0: [mem 0x1f80c0000-0x1f80fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 15.393416] pci 0000:00:00.6: BAR 2: [mem 0x1f81c0000-0x1f81cffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 15.404619] pci 0000:00:00.6: PME# supported from D0 D3hot <6>[ 15.411259] pci 0000:00:1f.0: [1957:e001] type 00 class 0x080700 <6>[ 15.417634] OF: /soc/pcie@1f0000000: no msi-map translation for id 0xf8 on (null) / # <6>[ 15.425824] fsl_enetc 0000:00:00.0: Adding to iommu group 4 # <6>[ 15.537391] fsl_enetc 0000:00:00.0: enabling device (0400 -> 0402) #<6>[ 15.543920] fsl_enetc 0000:00:00.0: no MAC address specified for SI1, using ae:79:27:8c:11:0b <6>[ 15.552840] fsl_enetc 0000:00:00.0: no MAC address specified for SI2, using fe:6f:37:45:8e:bc <6>[ 15.575178] fsl_enetc 0000:00:00.1: Adding to iommu group 5 <6>[ 15.578517] fsl_enetc 0000:00:00.0 enp0s0f0: renamed from eth0 / # export SHELL=/bin/sh <6>[ 15.685409] fsl_enetc 0000:00:00.1: enabling device (0400 -> 0402) <6>[ 15.692881] fsl_enetc 0000:00:00.1: device is disabled, skipping export SH<6>[ 15.699536] fsl_enetc 0000:00:00.2: Adding to iommu group 6 ELL=/bin/sh / # . /lava-514106/environment <6>[ 15.813438] fsl_enetc 0000:00:00.2: enabling device (0400 -> 0402) <6>[ 15.820290] fsl_enetc 0000:00:00.2: device is disabled, skipping <6>[ 15.826793] fsl_enetc_mdio 0000:00:00.3: Adding to iommu group 7 . /lava-514106/environment / # /lava-514106/bin/lava-test-runner /lava-514106/0 <6>[ 15.937448] fsl_enetc_mdio 0000:00:00.3: enabling device (0400 -> 0402) <6>[ 15.945024] fsl_enetc_ptp 0000:00:00.4: Adding to iommu group 8 <6>[ 15.951908] fsl_enetc_ptp 0000:00:00.4: enabling device (0404 -> 0406) <4>[ 15.958876] ptp_qoriq: device tree node missing required elements, try automatic configuration <4>[ 15.967824] ttyS ttyS0: 1 input overrun(s) /<6>[ 15.972303] pps pps0: new PPS source ptp0 lava-514106/b<6>[ 15.977274] mscc_felix 0000:00:00.5: Adding to iommu group 9 intest-runner /l<6>[ 15.983977] mscc_felix 0000:00:00.5: device is disabled, skipping ava<6>[ 15.991733] fsl_enetc 0000:00:00.6: Adding to iommu group 10 /bin/sh: /lava-514106/bintest-runner: not found / # <6>[ 16.105412] fsl_enetc 0000:00:00.6: enabling device (0400 -> 0402) <6>[ 16.112278] fsl_enetc 0000:00:00.6: device is disabled, skipping <6>[ 16.118668] OF: /soc/pcie@1f0000000: no iommu-map translation for id 0xf8 on (null) <3>[ 16.126638] pcieport 0000:00:1f.0: of_irq_parse_pci: failed with rc=-22 <6>[ 16.135069] dwc3 3100000.usb: Adding to iommu group 11 <6>[ 16.141207] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 16.147006] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 <6>[ 16.155122] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 <6>[ 16.164844] xhci-hcd xhci-hcd.0.auto: irq 28, io mem 0x03100000 <6>[ 16.171163] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 16.176946] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 <6>[ 16.184903] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed <6>[ 16.192070] hub 1-0:1.0: USB hub found <6>[ 16.196124] hub 1-0:1.0: 1 port detected <6>[ 16.200530] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 16.209241] hub 2-0:1.0: USB hub found <6>[ 16.213292] hub 2-0:1.0: 1 port detected <6>[ 16.218317] dwc3 3110000.usb: Adding to iommu group 12 <6>[ 16.224450] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 16.230254] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 <6>[ 16.238360] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 <6>[ 16.248084] xhci-hcd xhci-hcd.1.auto: irq 29, io mem 0x03110000 <6>[ 16.254388] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 16.260163] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 <6>[ 16.268118] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed <6>[ 16.275249] hub 3-0:1.0: USB hub found <6>[ 16.279305] hub 3-0:1.0: 1 port detected <6>[ 16.283704] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 16.292405] hub 4-0:1.0: USB hub found <6>[ 16.296457] hub 4-0:1.0: 1 port detected <6>[ 16.302547] sdhci-esdhc 2150000.mmc: Adding to iommu group 13 <6>[ 16.309307] sdhci-esdhc 2140000.mmc: Adding to iommu group 14 <6>[ 16.316685] mali-dp f080000.display: Adding to iommu group 15 <6>[ 16.323140] fsl-edma 22c0000.dma-controller: Adding to iommu group 16 <6>[ 16.341207] 2270000.serial: ttyLP2 at MMIO 0x2270000 (irq = 24, base_baud = 12500000) is a FSL_LPUART <6>[ 16.341404] mmc1: SDHCI controller on 2140000.mmc [2140000.mmc] using ADMA <6>[ 16.351979] spi-nor spi1.0: w25q128fw (16384 Kbytes) <6>[ 16.357933] mmc0: SDHCI controller on 2150000.mmc [2150000.mmc] using ADMA <6>[ 16.463504] mmc0: new HS400 MMC card at address 0001 <6>[ 16.469398] mmcblk0: mmc0:0001 S0J56X 7.34 GiB <6>[ 16.474446] mmcblk0boot0: mmc0:0001 S0J56X partition 1 31.5 MiB <6>[ 16.480906] mmcblk0boot1: mmc0:0001 S0J56X partition 2 31.5 MiB <6>[ 16.487228] mmcblk0rpmb: mmc0:0001 S0J56X partition 3 4.00 MiB, chardev (234:0) <6>[ 16.495899] mmcblk0: p1 p2 <6>[ 16.545403] usb 3-1: new high-speed USB device number 2 using xhci-hcd <6>[ 16.756034] hub 3-1:1.0: USB hub found <6>[ 16.760273] hub 3-1:1.0: 7 ports detected