Trying 0.0.0.0... Connected to 0. Escape character is '^]'. U-Boot SPL 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) Initializing DDR....using raw memory timing SPI boot Trying to boot from SPI U-Boot 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) SoC: LS1028A Rev1.0 (0x870b0110) Clock Configuration: CPU0(A72):1300 MHz CPU1(A72):1300 MHz Bus: 400 MHz DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 34004010 00000030 00000000 00000000 00000010: 00000000 008f0000 0030c000 00000000 00000020: 06200000 00002580 00000000 00019016 00000030: 00000000 00000048 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000103 00000000 100e7026 00000000 00000070: bb580000 00020000 Model: Kontron SMARC-sAL28 Board Hardware Variant: Single PHY (3) RCW: sl28-3-11_q.bin DRAM: Detected UDIMM Fixed DDR on board 3.9 GiB DDR 3.9 GiB (DDR3, 32-bit, CL=11, ECC on) Using SERDES1 Protocol: 47960 (0xbb58) PCIe1: pcie@3400000 Root Complex: no link PCIe2: pcie@3500000 Root Complex: no link CPLD: v18 WDT: Started with servicing (60s timeout) Waking secondary cores to start from fbd3c000 All (2) cores are up. MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPI Flash... SF: Detected w25q32jw with page size 256 Bytes, erase size 64 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial VPD: Using device 0x50 on I2C Bus 2 Net: eth0: enetc-0, eth2: enetc-2 Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => dhcp dhcp enetc-0 Waiting for PHY auto negotiation to complete.... done BOOTP broadcast 1 BOOTP broadcast 2 DHCP client bound to address 172.16.0.80 (254 ms) => setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 => tftp 0x82000000 513105/tftp-deploy-464g9wfe/kernel/Image tftp 0x82000000 513105/tftp-deploy-464g9wfe/kernel/Image Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.80; sending through gateway 172.16.0.254 Filename '513105/tftp-deploy-464g9wfe/kernel/Image'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################## 6.3 MiB/s done Bytes transferred = 31263232 (1dd0a00 hex) => tftp 0x90080000 513105/tftp-deploy-464g9wfe/ramdisk/ramdisk.cpio.gz.uboot tftp 0x90080000 513105/tftp-deploy-464g9wfe/ramdisk/ramdisk.cpio.gz.uboot Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.80; sending through gateway 172.16.0.254 Filename '513105/tftp-deploy-464g9wfe/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x90080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# #### 14.2 MiB/s done Bytes transferred = 19130700 (123e94c hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 513105/tftp-deploy-464g9wfe/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb tftp 0x90000000 513105/tftp-deploy-464g9wfe/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.80; sending through gateway 172.16.0.254 Filename '513105/tftp-deploy-464g9wfe/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb'. Load address: 0x90000000 Loading: *## 8 MiB/s done Bytes transferred = 25279 (62bf hex) => setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => booti 0x82000000 0x90080000 0x90000000 booti 0x82000000 0x90080000 0x90000000 ## Loading init Ramdisk from Legacy Image at 90080000 ... Image Name: Created: 2024-11-08 12:26:10 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 19130636 Bytes = 18.2 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Using Device Tree in place at 0000000090000000, end 00000000900092be WARNING could not find node fsl,ls1028a-gpu: FDT_ERR_NOTFOUND. Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [ 0.000000] Linux version 5.10.226 (KernelCI@build-j368705-arm64-gcc-12-defconfig-78w2j) (aarch64-linux-gnu-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP PREEMPT Fri Nov 8 12:02:59 UTC 2024 [ 0.000000] Machine model: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: ns16550a0 at MMIO 0x00000000021c0500 (options '115200n8') [ 0.000000] printk: bootconsole [ns16550a0] enabled [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x20ff7fba80-0x20ff7fdfff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000020ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fbdfffff] [ 0.000000] node 0: [mem 0x0000002080000000-0x00000020ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] cma: Reserved 32 MiB at 0x00000000f9c00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv0.2 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] percpu: Embedded 24 pages/cpu s59288 r8192 d30824 u98304 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: Spectre-v3a [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: Spectre-v4 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: detected: ARM erratum 1742098 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1015296 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] software IO TLB: mapped [mem 0x00000000f5c00000-0x00000000f9c00000] (64MB) <6>[ 0.000000] Memory: 3897656K/4126720K available (14592K kernel code, 2818K rwdata, 7424K rodata, 5568K init, 531K bss, 196296K reserved, 32768K cma-reserved) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=2. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode <6>[ 0.000000] GICv3: 256 SPIs implemented <6>[ 0.000000] GICv3: 0 Extended SPIs implemented <6>[ 0.000000] GICv3: Distributor has no Range Selector support <6>[ 0.000000] GICv3: 16 PPIs implemented <6>[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006040000 <6>[ 0.000000] ITS [mem 0x06020000-0x0603ffff] <6>[ 0.000000] ITS@0x0000000006020000: allocated 65536 Devices @2080080000 (flat, esz 8, psz 64K, shr 0) <6>[ 0.000000] ITS: using cache flushing for cmd queue <6>[ 0.000000] GICv3: using LPI property table @0x0000002080030000 <6>[ 0.000000] GIC: using cache flushing for LPI property table <6>[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000002080040000 <6>[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns <6>[ 0.000002] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns <6>[ 0.008712] Console: colour dummy device 80x25 <6>[ 0.013501] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) <6>[ 0.024219] pid_max: default: 32768 minimum: 301 <6>[ 0.029178] LSM: Security Framework initializing <6>[ 0.034145] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.041900] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.050985] rcu: Hierarchical SRCU implementation. <6>[ 0.056229] Platform MSI: gic-its@6020000 domain created <6>[ 0.061929] PCI/MSI: /interrupt-controller@6000000/gic-its@6020000 domain created <6>[ 0.069786] fsl-mc MSI: gic-its@6020000 domain created <6>[ 0.075917] EFI services will not be available. <6>[ 0.080861] smp: Bringing up secondary CPUs ... <6>[ 0.085984] Detected PIPT I-cache on CPU1 <6>[ 0.086006] GICv3: CPU1: found redistributor 1 region 0:0x0000000006060000 <6>[ 0.086013] GICv3: CPU1: using allocated LPI pending table @0x0000002080050000 <6>[ 0.086039] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] <6>[ 0.086094] smp: Brought up 1 node, 2 CPUs <6>[ 0.116409] SMP: Total of 2 processors activated. <6>[ 0.121421] CPU features: detected: 32-bit EL0 Support <6>[ 0.126880] CPU features: detected: CRC32 instructions <6>[ 0.132331] CPU features: detected: 32-bit EL1 Support <6>[ 0.147168] CPU: All CPU(s) started at EL2 <6>[ 0.151595] alternatives: patching kernel code <6>[ 0.157098] devtmpfs: initialized <4>[ 0.162878] KASLR disabled due to lack of seed <6>[ 0.167744] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.177851] futex hash table entries: 512 (order: 3, 32768 bytes, linear) <6>[ 0.185529] pinctrl core: initialized pinctrl subsystem <6>[ 0.191684] DMI not present or invalid. <6>[ 0.196192] NET: Registered protocol family 16 <6>[ 0.201821] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.209316] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.217444] audit: initializing netlink subsys (disabled) <5>[ 0.223250] audit: type=2000 audit(0.152:1): state=initialized audit_enabled=0 res=1 <6>[ 0.223757] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.231338] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.237819] cpuidle: using governor menu <6>[ 0.248989] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.256131] ASID allocator initialised with 65536 entries <6>[ 0.262392] Serial: AMBA PL011 UART driver <6>[ 0.269892] Machine: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier <6>[ 0.277542] SoC family: QorIQ LS1028A <6>[ 0.281495] SoC ID: svr:0x870b0110, Revision: 1.0 <6>[ 0.299288] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.306324] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.313357] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.320386] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.328296] ACPI: Interpreter disabled. <6>[ 0.333345] iommu: Default domain type: Translated <6>[ 0.338637] vgaarb: loaded <5>[ 0.341788] SCSI subsystem initialized <6>[ 0.346041] usbcore: registered new interface driver usbfs <6>[ 0.351865] usbcore: registered new interface driver hub <6>[ 0.357503] usbcore: registered new device driver usb <6>[ 0.363121] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.370946] i2c i2c-0: IMX I2C adapter registered <6>[ 0.376132] imx-i2c 2030000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.383786] i2c i2c-1: IMX I2C adapter registered <6>[ 0.388888] imx-i2c 2040000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.396614] i2c i2c-2: IMX I2C adapter registered <6>[ 0.401904] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.407179] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.416680] PTP clock support registered <6>[ 0.420978] EDAC MC: Ver: 3.0.0 <6>[ 0.425140] FPGA manager framework <6>[ 0.428881] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.435747] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.442260] VFS: Disk quotas dquot_6.6.0 <6>[ 0.446510] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 0.453819] pnp: PnP ACPI: disabled <6>[ 0.460819] NET: Registered protocol family 2 <6>[ 0.465781] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 0.474789] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear) <6>[ 0.483714] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) <6>[ 0.492065] TCP bind hash table entries: 32768 (order: 7, 524288 bytes, linear) <6>[ 0.500085] TCP: Hash tables configured (established 32768 bind 32768) <6>[ 0.507043] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.514095] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.521650] NET: Registered protocol family 1 <6>[ 0.526613] RPC: Registered named UNIX socket transport module. <6>[ 0.532870] RPC: Registered udp transport module. <6>[ 0.537881] RPC: Registered tcp transport module. <6>[ 0.542891] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.549661] PCI: CLS 0 bytes, default 64 <6>[ 0.553972] Unpacking initramfs... <6>[ 1.199615] Freeing initrd memory: 18676K <6>[ 1.204263] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available <6>[ 1.213013] kvm [1]: IPA Size Limit: 44 bits <6>[ 1.218362] kvm [1]: GICv3: no GICV resource entry <6>[ 1.223466] kvm [1]: disabling GICv2 emulation <6>[ 1.228224] kvm [1]: GIC system register CPU interface enabled <6>[ 1.234407] kvm [1]: vgic interrupt IRQ9 <6>[ 1.238693] kvm [1]: Hyp mode initialized successfully <5>[ 1.244721] Initialise system trusted keyrings <6>[ 1.249598] workingset: timestamp_bits=42 max_order=20 bucket_order=0 <6>[ 1.259512] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.266078] NFS: Registering the id_resolver key type <5>[ 1.271469] Key type id_resolver registered <5>[ 1.275957] Key type id_legacy registered <6>[ 1.280313] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 1.287345] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 1.295165] 9p: Installing v9fs 9p2000 file system support <5>[ 1.330334] Key type asymmetric registered <5>[ 1.334732] Asymmetric key parser 'x509' registered <6>[ 1.339937] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 1.347670] io scheduler mq-deadline registered <6>[ 1.352510] io scheduler kyber registered <4>[ 1.362649] EINJ: ACPI disabled. <6>[ 1.373776] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 1.381654] printk: console [ttyS0] disabled <6>[ 1.386276] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 23, base_baud = 12500000) is a 16550A <6>[ 1.395442] printk: console [ttyS0] enabled <6>[ 1.395442] printk: console [ttyS0] enabled <6>[ 1.404382] printk: bootconsole [ns16550a0] disabled <6>[ 1.404382] printk: bootconsole [ns16550a0] disabled <6>[ 1.415233] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 23, base_baud = 12500000) is a 16550A <6>[ 1.424619] SuperH (H)SCI(F) driver initialized <6>[ 1.429719] msm_serial: driver initialized <6>[ 1.437746] loop: module loaded <6>[ 1.445937] megasas: 07.714.04.00-rc1 <6>[ 1.452102] spi-nor spi0.0: w25q32jwm (4096 Kbytes) <5>[ 1.466004] 8 fixed-partitions partitions found on MTD device 20c0000.spi <5>[ 1.473092] Creating 8 MTD partitions on \"20c0000.spi\": <5>[ 1.478613] 0x000000000000-0x000000010000 : \"rcw\" <5>[ 1.488175] 0x000000010000-0x000000100000 : \"failsafe bootloader\" <5>[ 1.496136] 0x000000100000-0x000000140000 : \"failsafe DP firmware\" <5>[ 1.504131] 0x000000140000-0x0000001e0000 : \"failsafe trusted firmware\" <5>[ 1.516129] 0x0000001e0000-0x000000200000 : \"reserved\" <5>[ 1.524123] 0x000000200000-0x000000210000 : \"configuration store\" <5>[ 1.532118] 0x000000210000-0x0000003e0000 : \"bootloader\" <5>[ 1.540129] 0x0000003e0000-0x000000400000 : \"bootloader environment\" <6>[ 1.549864] tun: Universal TUN/TAP device driver, 1.6 <6>[ 1.555666] thunder_xcv, ver 1.0 <6>[ 1.559187] thunder_bgx, ver 1.0 <6>[ 1.562703] nicpf, ver 1.0 <6>[ 1.566392] hclge is initializing <6>[ 1.569990] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 1.577504] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 1.583117] e1000: Intel(R) PRO/1000 Network Driver <6>[ 1.588272] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 1.594321] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 1.599563] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 1.605783] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 1.611460] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.617329] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 1.623879] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 1.630274] sky2: driver version 1.30 <6>[ 1.634839] VFIO - User Level meta-driver version: 0.3 <6>[ 1.641377] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 1.648208] ehci-pci: EHCI PCI platform driver <6>[ 1.652947] ehci-platform: EHCI generic platform driver <6>[ 1.658528] ehci-orion: EHCI orion driver <6>[ 1.662868] ehci-exynos: EHCI Exynos driver <6>[ 1.667377] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 1.673854] ohci-pci: OHCI PCI platform driver <6>[ 1.678598] ohci-platform: OHCI generic platform driver <6>[ 1.684169] ohci-exynos: OHCI Exynos driver <6>[ 1.688905] usbcore: registered new interface driver usb-storage <6>[ 1.696742] i2c /dev entries driver <6>[ 1.703280] sp805-wdt c000000.watchdog: registration successful <6>[ 1.709600] sp805-wdt c010000.watchdog: registration successful <6>[ 1.716997] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver <6>[ 1.725660] sdhci: Secure Digital Host Controller Interface driver <6>[ 1.732147] sdhci: Copyright(c) Pierre Ossman <6>[ 1.737091] Synopsys Designware Multimedia Card Interface Driver <6>[ 1.743966] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 1.750846] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 1.757980] usbcore: registered new interface driver usbhid <6>[ 1.763842] usbhid: USB HID core driver <6>[ 1.770675] NET: Registered protocol family 17 <6>[ 1.775491] 9pnet: Installing 9P2000 support <5>[ 1.780071] Key type dns_resolver registered <6>[ 1.784812] registered taskstats version 1 <5>[ 1.789190] Loading compiled-in X.509 certificates <6>[ 1.806154] input: buttons0 as /devices/platform/buttons0/input/input0 <6>[ 14.087813] clk: Disabling unused clocks <6>[ 14.092153] ALSA device list: <6>[ 14.095412] No soundcards found. <6>[ 14.106232] Freeing unused kernel memory: 5568K <6>[ 14.111502] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 14.171560] udevd[81]: starting version 3.2.9 <5>[ 14.176749] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 14.183675] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 14.190440] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 14.199856] udevd[81]: specified user 'tss' unknown <27>[ 14.205174] udevd[81]: specified group 'tss' unknown <30>[ 14.211353] udevd[82]: starting eudev-3.2.9 <4>[ 14.406639] at24 0-0050: supply vcc not found, using dummy regulator <4>[ 14.417744] rtc-rv8803 0-0032: Voltage low, temperature compensation stopped. <4>[ 14.428287] rtc-rv8803 0-0032: Voltage low, data loss detected. <6>[ 14.437157] at24 0-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 14.447316] wm8904 2-001a: supply DCVDD not found, using dummy regulator <4>[ 14.447488] at24 1-0057: supply vcc not found, using dummy regulator <4>[ 14.463924] wm8904 2-001a: supply DBVDD not found, using dummy regulator <6>[ 14.471870] at24 1-0057: 8192 byte 24c64 EEPROM, writable, 32 bytes/write <4>[ 14.477294] wm8904 2-001a: supply AVDD not found, using dummy regulator <4>[ 14.479839] rtc-rv8803 0-0032: Voltage low, data is invalid. <4>[ 14.492698] at24 2-0050: supply vcc not found, using dummy regulator <4>[ 14.498759] wm8904 2-001a: supply CPVDD not found, using dummy regulator <6>[ 14.506482] rtc-rv8803 0-0032: registered as rtc0 <4>[ 14.507105] wm8904 2-001a: supply MICVDD not found, using dummy regulator <6>[ 14.512050] at24 2-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 14.526799] rtc-rv8803 0-0032: Voltage low, data is invalid. <3>[ 14.533635] rtc-rv8803 0-0032: hctosys: unable to read the hardware clock <6>[ 14.541322] wm8904 2-001a: revision A <6>[ 14.547960] sl28cpld-wdt 2000000.i2c:sl28cpld@4a:watchdog@4: initial timeout 6 sec <6>[ 14.581855] caam 8000000.crypto: Entropy delay = 3200 <5>[ 14.612319] arm-smmu 5000000.iommu: probing hardware configuration... <5>[ 14.620055] arm-smmu 5000000.iommu: SMMUv2 with: <5>[ 14.627121] arm-smmu 5000000.iommu: stage 1 translation <6>[ 14.632140] caam 8000000.crypto: Instantiated RNG4 SH0 <5>[ 14.633759] arm-smmu 5000000.iommu: stage 2 translation <5>[ 14.644918] arm-smmu 5000000.iommu: nested translation <5>[ 14.652096] arm-smmu 5000000.iommu: stream matching with 128 register groups <6>[ 14.655212] caam 8000000.crypto: Instantiated RNG4 SH1 <5>[ 14.661011] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) <5>[ 14.673300] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 <5>[ 14.680070] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA <5>[ 14.687652] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA <6>[ 14.691800] caam 8000000.crypto: device ID = 0x0a12070000000000 (Era 10) <6>[ 14.695918] fsl-edma 22c0000.dma-controller: Adding to iommu group 0 <6>[ 14.704523] caam 8000000.crypto: job rings = 4, qi = 0 <6>[ 14.710427] pci-host-generic 1f0000000.pcie: host bridge /soc/pcie@1f0000000 ranges: <6>[ 14.722675] pci-host-generic 1f0000000.pcie: MEM 0x01f8000000..0x01f815ffff -> 0x0000000000 <6>[ 14.734526] pci-host-generic 1f0000000.pcie: MEM 0x01f8160000..0x01f81cffff -> 0x0000000000 <6>[ 14.744068] pci-host-generic 1f0000000.pcie: MEM 0x01f81d0000..0x01f81effff -> 0x0000000000 <6>[ 14.753314] pci-host-generic 1f0000000.pcie: MEM 0x01f81f0000..0x01f820ffff -> 0x0000000000 <6>[ 14.762722] pci-host-generic 1f0000000.pcie: MEM 0x01f8210000..0x01f822ffff -> 0x0000000000 <6>[ 14.771976] pci-host-generic 1f0000000.pcie: MEM 0x01f8230000..0x01f824ffff -> 0x0000000000 <6>[ 14.781199] pci-host-generic 1f0000000.pcie: MEM 0x01fc000000..0x01fc3fffff -> 0x0000000000 <6>[ 14.790472] pci-host-generic 1f0000000.pcie: ECAM at [mem 0x1f0000000-0x1f00fffff] for [bus 00] <6>[ 14.790821] caam_jr 8010000.jr: Adding to iommu group 1 <6>[ 14.799720] pci-host-generic 1f0000000.pcie: PCI host bridge to bus 0000:00 <6>[ 14.805750] caam algorithms registered in /proc/crypto <6>[ 14.812365] pci_bus 0000:00: root bus resource [bus 00] <6>[ 14.817761] caam 8000000.crypto: registering rng-caam <6>[ 14.823293] pci_bus 0000:00: root bus resource [mem 0x1f8000000-0x1f815ffff] (bus address [0x00000000-0x0015ffff]) <6>[ 14.828938] caam_jr 8020000.jr: Adding to iommu group 2 <6>[ 14.839204] pci_bus 0000:00: root bus resource [mem 0x1f8160000-0x1f81cffff pref] (bus address [0x00000000-0x0006ffff]) <6>[ 14.839208] pci_bus 0000:00: root bus resource [mem 0x1f81d0000-0x1f81effff] (bus address [0x00000000-0x0001ffff]) <6>[ 14.839212] pci_bus 0000:00: root bus resource [mem 0x1f81f0000-0x1f820ffff pref] (bus address [0x00000000-0x0001ffff]) <6>[ 14.839216] pci_bus 0000:00: root bus resource [mem 0x1f8210000-0x1f822ffff] (bus address [0x00000000-0x0001ffff]) <6>[ 14.839221] pci_bus 0000:00: root bus resource [mem 0x1f8230000-0x1f824ffff pref] (bus address [0x00000000-0x0001ffff]) <6>[ 14.845301] caam_jr 8030000.jr: Adding to iommu group 3 <6>[ 14.855814] pci_bus 0000:00: root bus resource [mem 0x1fc000000-0x1fc3fffff] (bus address [0x00000000-0x003fffff]) <6>[ 14.855839] pci 0000:00:00.0: [1957:e100] type 00 class 0x020001 <6>[ 14.866928] caam_jr 8040000.jr: Adding to iommu group 4 done<6>[ 14.877749] pci 0000:00:00.0: BAR 0: [mem 0x1f8000000-0x1f803ffff 64bit] (from Enhanced Allocation, properties 0x0) <5>[ 14.888816] random: crng init done <6>[ 14.899378] pci 0000:00:00.0: BAR 2: [mem 0x1f8160000-0x1f816ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <5>[ 14.908582] random: 2 urandom warning(s) missed due to ratelimiting <6>[ 14.927359] pci 0000:00:00.0: VF BAR 0: [mem 0x1f81d0000-0x1f81dffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 14.970999] pci 0000:00:00.0: VF BAR 2: [mem 0x1f81f0000-0x1f81fffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 14.982479] pci 0000:00:00.0: PME# supported from D0 D3hot Saving random se<6>[ 14.988275] pci 0000:00:00.0: VF(n) BAR0 space: [mem 0x1f81d0000-0x1f81effff 64bit] (contains BAR0 for 2 VFs) ed: <6>[ 14.999930] pci 0000:00:00.0: VF(n) BAR2 space: [mem 0x1f81f0000-0x1f820ffff 64bit pref] (contains BAR2 for 2 VFs) OK <6>[ 15.011157] pci 0000:00:00.1: [1957:e100] type 00 class 0x020001 Starting network<6>[ 15.017727] pci 0000:00:00.1: BAR 0: [mem 0x1f8040000-0x1f807ffff 64bit] (from Enhanced Allocation, properties 0x0) : OK <6>[ 15.029823] pci 0000:00:00.1: BAR 2: [mem 0x1f8170000-0x1f817ffff 64bit pref] (from Enhanced Allocation, properties 0x1) Starting dropbea<6>[ 15.041500] pci 0000:00:00.1: VF BAR 0: [mem 0x1f8210000-0x1f821ffff 64bit] (from Enhanced Allocation, properties 0x4) r sshd: <6>[ 15.053962] pci 0000:00:00.1: VF BAR 2: [mem 0x1f8230000-0x1f823ffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 15.066174] pci 0000:00:00.1: PME# supported from D0 D3hot <6>[ 15.072032] pci 0000:00:00.1: VF(n) BAR0 space: [mem 0x1f8210000-0x1f822ffff 64bit] (contains BAR0 for 2 VFs) <6>[ 15.073803] NET: Registered protocol family 10 <6>[ 15.082358] pci 0000:00:00.1: VF(n) BAR2 space: [mem 0x1f8230000-0x1f824ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 15.087571] Segment Routing with IPv6 <6>[ 15.097844] pci 0000:00:00.2: [1957:e100] type 00 class 0x020001 OK <6>[ 15.108462] pci 0000:00:00.2: BAR 0: [mem 0x1f8080000-0x1f80bffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 15.119409] pci 0000:00:00.2: BAR 2: [mem 0x1f8180000-0x1f818ffff 64bit pref] (from Enhanced Allocation, properties 0x1) /bin/sh: <6>[ 15.130731] pci 0000:00:00.2: PME# supported from D0 D3hot can't access tty<6>[ 15.137504] pci 0000:00:00.3: [1957:ee01] type 00 class 0x088001 ; job control tu<6>[ 15.144932] pci 0000:00:00.3: BAR 0: [mem 0x1f8100000-0x1f811ffff 64bit] (from Enhanced Allocation, properties 0x0) rned off / # <6>[ 15.157003] pci 0000:00:00.3: BAR 2: [mem 0x1f8190000-0x1f819ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 15.169397] pci 0000:00:00.3: PME# supported from D0 D3hot <6>[ 15.175312] pci 0000:00:00.4: [1957:ee02] type 00 class 0x088001 <6>[ 15.181665] pci 0000:00:00.4: BAR 0: [mem 0x1f8120 000-0x1f813ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 15.192413] pci 0000:00:00.4: BAR 2: [mem 0x1f81a0000-0x1f81affff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 15.203606] pci 0000:00:00.4: PME# supported from D0 D3hot <6>[ 15.209506] pci 0000:00:00.5: [1957:eef0] type 00 class 0x020801 <6>[ 15.215828] pci 0000:00:00.5: BAR 0: [mem 0x1f8140000-0x1f815ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 15.226575] pci 0000:00:00.5: BAR 2: [mem 0x1f81b0000-0x1f81bffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 15.237754] pci 0000:00:00.5: BAR 4: [mem 0x1fc000000-0x1fc3fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 15.248517] pci 0000:00:00.5: PME# supported from D0 D3hot <6>[ 15.254481] pci 0000:00:00.6: [1957:e100] type 00 class 0x020001 <6>[ 15.260847] pci 0000:00:00.6: BAR 0: [mem 0x1f80c0000-0x1f80fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 15.271590] pci 0000:00:00.6: BAR 2: [mem 0x1f81c0000-0x1f81cffff 64bit pref] (from Enhanced Allocation, properties 0x1) / # <6>[ 15.282784] pci 0000:00:00.6: PME# supported from D0 D3hot <6>[ 15.289782] pci 0000:00:1f.0: [1957:e001] type 00 class 0x080700 <6>[ 15.296153] OF: /soc/pcie@1f0000000: no msi-map translation for id 0xf8 on (null) <6>[ 15.304281] fsl_enetc 000# 0:00:00.0: Adding to iommu group 5 #<6>[ 15.415783] fsl_enetc 0000:00:00.0: enabling device (0400 -> 0402) <6>[ 15.422297] fsl_enetc 0000:00:00.0: no MAC address specified for SI1, using ae:aa:ad:46:0a:29 <6>[ 15.431128] fsl_enetc 0000:00:00.0: no MAC address specified for SI2, using b6:c2:6a:3f:a6:c1 / # <6>[ 15.453428] fsl_enetc 0000:00:00.1: Adding to iommu group 6 <6>[ 15.454868] fsl_enetc 0000:00:00.0 enp0s0f0: renamed from eth0 export SHELL=/bin/sh export SHELL=/bin/sh<6>[ 15.567843] fsl_enetc 0000:00:00.1: enabling device (0400 -> 0402) <6>[ 15.575292] fsl_enetc 0000:00:00.1: device is disabled, skipping <6>[ 15.581825] fsl_enetc 0000:00:00.2: Adding to iommu group 7 / # . /lava-513105/environment . /lava-51<6>[ 15.695835] fsl_enetc 0000:00:00.2: enabling device (0400 -> 0402) 3105/environ<6>[ 15.703005] fsl_enetc 0000:00:00.2: device is disabled, skipping ment<6>[ 15.710044] fsl_enetc_mdio 0000:00:00.3: Adding to iommu group 8 / # /lava-513105/bin/lava-test-runner /lava-513105/0 /lava-513105/bin/lava-test-runner /lava-513105/0<6>[ 15.823845] fsl_enetc_mdio 0000:00:00.3: enabling device (0400 -> 0402) <6>[ 15.831187] fsl_enetc_ptp 0000:00:00.4: Adding to iommu group 9 <6>[ 15.837536] fsl_enetc_ptp 0000:00:00.4: enabling device (0404 -> 0406) <4>[ 15.844487] ptp_qoriq: device tree node missing required elements, try automatic configuration <6>[ 15.853534] pps pps0: new PPS source ptp0 <6>[ 15.858155] mscc_felix 0000:00:00.5: Adding to iommu group 10 <6>[ 15.864683] mscc_felix 0000:00:00.5: device is disabled, skipping <6>[ 15.872610] fsl_enetc 0000:00:00.6: Adding to iommu group 11 + export 'TESTRUN_ID=0_dmesg' + c<8>[ 15.882187] d /lava-513105/0/tests/0_dmesg + cat uuid + UUID=513105_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 15.900904] <8>[ 15.919807] <8>[ 15.939540] + <8>[ 15.948746] set +x <3>[ 16.005107] pcieport 0000:00:1f.0: of_irq_parse_pci: failed with rc=-2�