Trying 0.0.0.0... Connected to 0. Escape character is '^]'. U-Boot SPL 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) Initializing DDR....using raw memory timing SPI boot Trying to boot from SPI U-Boot 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) SoC: LS1028A Rev1.0 (0x870b0110) Clock Configuration: CPU0(A72):1300 MHz CPU1(A72):1300 MHz Bus: 400 MHz DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 34004010 00000030 00000000 00000000 00000010: 00000000 008f0000 0030c000 00000000 00000020: 06200000 00002580 00000000 00019016 00000030: 00000000 00000048 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000103 00000000 100e7026 00000000 00000070: bb580000 00020000 Model: Kontron SMARC-sAL28 Board Hardware Variant: Single PHY (3) RCW: sl28-3-11_q.bin DRAM: Detected UDIMM Fixed DDR on board 3.9 GiB DDR 3.9 GiB (DDR3, 32-bit, CL=11, ECC on) Using SERDES1 Protocol: 47960 (0xbb58) PCIe1: pcie@3400000 Root Complex: no link PCIe2: pcie@3500000 Root Complex: no link CPLD: v18 WDT: Started with servicing (60s timeout) Waking secondary cores to start from fbd3c000 All (2) cores are up. MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPI Flash... SF: Detected w25q32jw with page size 256 Bytes, erase size 64 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial VPD: Using device 0x50 on I2C Bus 2 Net: eth0: enetc-0, eth2: enetc-2 Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => dhcp dhcp enetc-0 Waiting for PHY auto negotiation to complete.... done BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.0.64 (1255 ms) => setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 => tftp 0x82000000 514093/tftp-deploy-zwt_1_6c/kernel/Image tftp 0x82000000 514093/tftp-deploy-zwt_1_6c/kernel/Image Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.64; sending through gateway 172.16.0.254 Filename '514093/tftp-deploy-zwt_1_6c/kernel/Image'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########################## 11.9 MiB/s done Bytes transferred = 33769984 (2034a00 hex) => tftp 0x90080000 514093/tftp-deploy-zwt_1_6c/ramdisk/ramdisk.cpio.gz.uboot tftp 0x90080000 514093/tftp-deploy-zwt_1_6c/ramdisk/ramdisk.cpio.gz.uboot Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.64; sending through gateway 172.16.0.254 Filename '514093/tftp-deploy-zwt_1_6c/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x90080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ##### 15.4 MiB/s done Bytes transferred = 20099501 (132b1ad hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 514093/tftp-deploy-zwt_1_6c/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb tftp 0x90000000 514093/tftp-deploy-zwt_1_6c/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.64; sending through gateway 172.16.0.254 Filename '514093/tftp-deploy-zwt_1_6c/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb'. Load address: 0x90000000 Loading: *## 6.1 MiB/s done Bytes transferred = 25626 (641a hex) => setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => booti 0x82000000 0x90080000 0x90000000 booti 0x82000000 0x90080000 0x90000000 ## Loading init Ramdisk from Legacy Image at 90080000 ... Image Name: Created: 2024-11-11 14:11:08 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 20099437 Bytes = 19.2 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Using Device Tree in place at 0000000090000000, end 0000000090009419 WARNING could not find node fsl,ls1028a-gpu: FDT_ERR_NOTFOUND. Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [ 0.000000] Linux version 5.15.167 (KernelCI@build-j372809-arm64-gcc-12-defconfig-cch4k) (aarch64-linux-gnu-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP PREEMPT Mon Nov 11 13:43:44 UTC 2024 [ 0.000000] Machine model: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: ns16550a0 at MMIO 0x00000000021c0500 (options '115200n8') [ 0.000000] printk: bootconsole [ns16550a0] enabled [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x20ff7faa80-0x20ff7fcfff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000020ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fbdfffff] [ 0.000000] node 0: [mem 0x0000002080000000-0x00000020ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] On node 0, zone Normal: 16896 pages in unavailable ranges [ 0.000000] cma: Reserved 32 MiB at 0x00000000f9c00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv0.2 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] percpu: Embedded 20 pages/cpu s41560 r8192 d32168 u81920 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: Spectre-v3a [ 0.000000] CPU features: detected: Spectre-v4 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1015296 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <5>[ 0.000000] Unknown kernel command line parameters \"n8\", will be passed to user space. <6>[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] software IO TLB: mapped [mem 0x00000000f5c00000-0x00000000f9c00000] (64MB) <6>[ 0.000000] Memory: 3894376K/4126720K available (15232K kernel code, 3090K rwdata, 8320K rodata, 6208K init, 512K bss, 199576K reserved, 32768K cma-reserved) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=2. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode <6>[ 0.000000] GICv3: 256 SPIs implemented <6>[ 0.000000] GICv3: 0 Extended SPIs implemented <6>[ 0.000000] GICv3: Distributor has no Range Selector support <6>[ 0.000000] Root IRQ handler: gic_handle_irq <6>[ 0.000000] GICv3: 16 PPIs implemented <6>[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006040000 <6>[ 0.000000] ITS [mem 0x06020000-0x0603ffff] <6>[ 0.000000] ITS@0x0000000006020000: allocated 65536 Devices @2080080000 (flat, esz 8, psz 64K, shr 0) <6>[ 0.000000] ITS: using cache flushing for cmd queue <6>[ 0.000000] GICv3: using LPI property table @0x0000002080030000 <6>[ 0.000000] GIC: using cache flushing for LPI property table <6>[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000002080040000 <6>[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns <6>[ 0.000000] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns <6>[ 0.008719] Console: colour dummy device 80x25 <6>[ 0.013508] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) <6>[ 0.024226] pid_max: default: 32768 minimum: 301 <6>[ 0.029176] LSM: Security Framework initializing <6>[ 0.034172] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.041929] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.051065] rcu: Hierarchical SRCU implementation. <6>[ 0.056315] Platform MSI: gic-its@6020000 domain created <6>[ 0.062015] PCI/MSI: /interrupt-controller@6000000/gic-its@6020000 domain created <6>[ 0.069876] fsl-mc MSI: gic-its@6020000 domain created <6>[ 0.075924] EFI services will not be available. <6>[ 0.080857] smp: Bringing up secondary CPUs ... <6>[ 0.085971] Detected PIPT I-cache on CPU1 <6>[ 0.085994] GICv3: CPU1: found redistributor 1 region 0:0x0000000006060000 <6>[ 0.086002] GICv3: CPU1: using allocated LPI pending table @0x0000002080050000 <6>[ 0.086026] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] <6>[ 0.086085] smp: Brought up 1 node, 2 CPUs <6>[ 0.116402] SMP: Total of 2 processors activated. <6>[ 0.121413] CPU features: detected: 32-bit EL0 Support <6>[ 0.126869] CPU features: detected: 32-bit EL1 Support <6>[ 0.132319] CPU features: detected: CRC32 instructions <6>[ 0.147507] CPU: All CPU(s) started at EL2 <6>[ 0.151936] alternatives: patching kernel code <6>[ 0.157356] devtmpfs: initialized <4>[ 0.163104] KASLR disabled due to lack of seed <6>[ 0.167967] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.178075] futex hash table entries: 512 (order: 3, 32768 bytes, linear) <6>[ 0.185766] pinctrl core: initialized pinctrl subsystem <6>[ 0.191805] DMI not present or invalid. <6>[ 0.196324] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.203367] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.210854] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.218981] audit: initializing netlink subsys (disabled) <5>[ 0.224787] audit: type=2000 audit(0.152:1): state=initialized audit_enabled=0 res=1 <6>[ 0.225302] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.232876] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.239354] cpuidle: using governor menu <6>[ 0.250526] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.257671] ASID allocator initialised with 65536 entries <6>[ 0.264095] Serial: AMBA PL011 UART driver <6>[ 0.271703] Machine: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier <6>[ 0.279354] SoC family: QorIQ LS1028A <6>[ 0.283307] SoC ID: svr:0x870b0110, Revision: 1.0 <6>[ 0.301920] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.308962] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.315991] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.323019] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.330866] ACPI: Interpreter disabled. <6>[ 0.336077] iommu: Default domain type: Translated <6>[ 0.341260] iommu: DMA domain TLB invalidation policy: strict mode <6>[ 0.347969] vgaarb: loaded <5>[ 0.351091] SCSI subsystem initialized <6>[ 0.355344] usbcore: registered new interface driver usbfs <6>[ 0.361168] usbcore: registered new interface driver hub <6>[ 0.366809] usbcore: registered new device driver usb <6>[ 0.372418] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.380222] i2c i2c-0: IMX I2C adapter registered <6>[ 0.385407] imx-i2c 2030000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.393063] i2c i2c-1: IMX I2C adapter registered <6>[ 0.398167] imx-i2c 2040000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.405878] i2c i2c-2: IMX I2C adapter registered <6>[ 0.411211] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.416487] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.425987] PTP clock support registered <6>[ 0.430287] EDAC MC: Ver: 3.0.0 <6>[ 0.434549] FPGA manager framework <6>[ 0.438292] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.445153] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.451668] VFS: Disk quotas dquot_6.6.0 <6>[ 0.455917] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 0.463212] pnp: PnP ACPI: disabled <6>[ 0.470307] NET: Registered PF_INET protocol family <6>[ 0.475786] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 0.484894] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear) <6>[ 0.493817] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.501910] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) <6>[ 0.510244] TCP bind hash table entries: 32768 (order: 7, 524288 bytes, linear) <6>[ 0.518235] TCP: Hash tables configured (established 32768 bind 32768) <6>[ 0.525188] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.532241] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.539799] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.546101] RPC: Registered named UNIX socket transport module. <6>[ 0.552348] RPC: Registered udp transport module. <6>[ 0.557358] RPC: Registered tcp transport module. <6>[ 0.562370] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.569140] PCI: CLS 0 bytes, default 64 <6>[ 0.573483] Unpacking initramfs... <6>[ 0.581403] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available <6>[ 0.590176] kvm [1]: IPA Size Limit: 44 bits <6>[ 0.595560] kvm [1]: GICv3: no GICV resource entry <6>[ 0.600684] kvm [1]: disabling GICv2 emulation <6>[ 0.605458] kvm [1]: GIC system register CPU interface enabled <6>[ 0.611667] kvm [1]: vgic interrupt IRQ9 <6>[ 0.615954] kvm [1]: Hyp mode initialized successfully <5>[ 0.622036] Initialise system trusted keyrings <6>[ 0.626941] workingset: timestamp_bits=42 max_order=20 bucket_order=0 <6>[ 0.637197] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.643791] NFS: Registering the id_resolver key type <5>[ 0.649214] Key type id_resolver registered <5>[ 0.653716] Key type id_legacy registered <6>[ 0.658091] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.665130] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 0.672970] 9p: Installing v9fs 9p2000 file system support <5>[ 0.707766] Key type asymmetric registered <5>[ 0.712171] Asymmetric key parser 'x509' registered <6>[ 0.717417] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 0.725158] io scheduler mq-deadline registered <6>[ 0.730000] io scheduler kyber registered <6>[ 0.741204] EINJ: ACPI disabled. <6>[ 0.754181] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 0.762330] printk: console [ttyS0] disabled <6>[ 0.766960] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 24, base_baud = 12500000) is a 16550A <6>[ 0.776137] printk: console [ttyS0] enabled <6>[ 0.776137] printk: console [ttyS0] enabled <6>[ 0.785090] printk: bootconsole [ns16550a0] disabled <6>[ 0.785090] printk: bootconsole [ns16550a0] disabled <6>[ 0.796029] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 24, base_baud = 12500000) is a 16550A <6>[ 0.805563] SuperH (H)SCI(F) driver initialized <6>[ 0.810722] msm_serial: driver initialized <5>[ 0.816252] arm-smmu 5000000.iommu: probing hardware configuration... <5>[ 0.822986] arm-smmu 5000000.iommu: SMMUv2 with: <5>[ 0.827882] arm-smmu 5000000.iommu: stage 1 translation <5>[ 0.833480] arm-smmu 5000000.iommu: stage 2 translation <5>[ 0.839074] arm-smmu 5000000.iommu: nested translation <5>[ 0.844581] arm-smmu 5000000.iommu: stream matching with 128 register groups <5>[ 0.852008] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) <5>[ 0.858825] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 <5>[ 0.865553] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA <5>[ 0.872279] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA <6>[ 0.882710] loop: module loaded <6>[ 0.893468] megasas: 07.717.02.00-rc1 <6>[ 0.899815] spi-nor spi0.0: w25q32jwm (4096 Kbytes) <6>[ 1.254118] Freeing initrd memory: 19624K <5>[ 1.269428] 5 fixed-partitions partitions found on MTD device 20c0000.spi <5>[ 1.276518] Creating 5 MTD partitions on \"20c0000.spi\": <5>[ 1.282037] 0x000000000000-0x000000010000 : \"rcw\" <5>[ 1.287664] 0x000000010000-0x0000001e0000 : \"failsafe bootloader\" <5>[ 1.294583] 0x000000200000-0x000000210000 : \"configuration store\" <5>[ 1.301515] 0x000000210000-0x0000003e0000 : \"bootloader\" <5>[ 1.307665] 0x0000003e0000-0x000000400000 : \"bootloader environment\" <6>[ 1.316798] tun: Universal TUN/TAP device driver, 1.6 <6>[ 1.322673] thunder_xcv, ver 1.0 <6>[ 1.326195] thunder_bgx, ver 1.0 <6>[ 1.329712] nicpf, ver 1.0 <6>[ 1.333555] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 1.341071] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 1.346690] hclge is initializing <6>[ 1.350285] e1000: Intel(R) PRO/1000 Network Driver <6>[ 1.355440] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 1.361484] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 1.366726] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 1.372948] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 1.378626] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.384498] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 1.391048] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 1.397449] sky2: driver version 1.30 <6>[ 1.402013] VFIO - User Level meta-driver version: 0.3 <6>[ 1.407792] dwc3 3100000.usb: Adding to iommu group 0 <6>[ 1.413717] dwc3 3110000.usb: Adding to iommu group 1 <6>[ 1.420551] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 1.427381] ehci-pci: EHCI PCI platform driver <6>[ 1.432123] ehci-platform: EHCI generic platform driver <6>[ 1.437704] ehci-orion: EHCI orion driver <6>[ 1.442048] ehci-exynos: EHCI Exynos driver <6>[ 1.446562] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 1.453035] ohci-pci: OHCI PCI platform driver <6>[ 1.457776] ohci-platform: OHCI generic platform driver <6>[ 1.463348] ohci-exynos: OHCI Exynos driver <6>[ 1.468054] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 1.473834] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 <6>[ 1.481912] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000008002010010 <6>[ 1.491632] xhci-hcd xhci-hcd.0.auto: irq 29, io mem 0x03100000 <6>[ 1.497924] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 1.503695] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 <6>[ 1.511645] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed <6>[ 1.518773] hub 1-0:1.0: USB hub found <6>[ 1.522813] hub 1-0:1.0: 1 port detected <6>[ 1.527183] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 1.535801] hub 2-0:1.0: USB hub found <6>[ 1.539839] hub 2-0:1.0: 1 port detected <6>[ 1.544243] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 1.550026] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 <6>[ 1.558100] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000008002010010 <6>[ 1.567815] xhci-hcd xhci-hcd.1.auto: irq 30, io mem 0x03110000 <6>[ 1.574113] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 1.579884] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 <6>[ 1.587837] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed <6>[ 1.594911] hub 3-0:1.0: USB hub found <6>[ 1.598951] hub 3-0:1.0: 1 port detected <6>[ 1.603304] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 1.611915] hub 4-0:1.0: USB hub found <6>[ 1.615952] hub 4-0:1.0: 1 port detected <6>[ 1.620569] usbcore: registered new interface driver usb-storage <6>[ 1.628563] i2c_dev: i2c /dev entries driver <6>[ 1.636027] sp805-wdt c000000.watchdog: registration successful <6>[ 1.642344] sp805-wdt c010000.watchdog: registration successful <6>[ 1.649838] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver <6>[ 1.658596] sdhci: Secure Digital Host Controller Interface driver <6>[ 1.665087] sdhci: Copyright(c) Pierre Ossman <6>[ 1.670157] Synopsys Designware Multimedia Card Interface Driver <6>[ 1.677043] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 1.683473] sdhci-esdhc 2140000.mmc: Adding to iommu group 2 <6>[ 1.689510] sdhci-esdhc 2150000.mmc: Adding to iommu group 3 <6>[ 1.689532] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 1.703061] usbcore: registered new interface driver usbhid <6>[ 1.708935] usbhid: USB HID core driver <6>[ 1.716216] NET: Registered PF_PACKET protocol family <6>[ 1.721170] mmc1: SDHCI controller on 2140000.mmc [2140000.mmc] using ADMA <6>[ 1.721662] mmc0: SDHCI controller on 2150000.mmc [2150000.mmc] using ADMA <6>[ 1.728951] 9pnet: Installing 9P2000 support <5>[ 1.740469] Key type dns_resolver registered <5>[ 1.745223] Loading compiled-in X.509 certificates <6>[ 1.752792] fsl-edma 22c0000.dma-controller: Adding to iommu group 4 <6>[ 1.760767] pci-host-generic 1f0000000.pcie: host bridge /soc/pcie@1f0000000 ranges: <6>[ 1.768841] pci-host-generic 1f0000000.pcie: MEM 0x01f8000000..0x01f815ffff -> 0x01f8000000 <6>[ 1.777958] pci-host-generic 1f0000000.pcie: MEM 0x01f8160000..0x01f81cffff -> 0x01f8160000 <6>[ 1.787104] pci-host-generic 1f0000000.pcie: MEM 0x01f81d0000..0x01f81effff -> 0x01f81d0000 <6>[ 1.796223] pci-host-generic 1f0000000.pcie: MEM 0x01f81f0000..0x01f820ffff -> 0x01f81f0000 <6>[ 1.805377] pci-host-generic 1f0000000.pcie: MEM 0x01f8210000..0x01f822ffff -> 0x01f8210000 <6>[ 1.814506] pci-host-generic 1f0000000.pcie: MEM 0x01f8230000..0x01f824ffff -> 0x01f8230000 <6>[ 1.823610] pci-host-generic 1f0000000.pcie: MEM 0x01fc000000..0x01fc3fffff -> 0x01fc000000 <6>[ 1.832749] pci-host-generic 1f0000000.pcie: ECAM at [mem 0x1f0000000-0x1f00fffff] for [bus 00] <6>[ 1.841827] pci-host-generic 1f0000000.pcie: PCI host bridge to bus 0000:00 <6>[ 1.849082] pci_bus 0000:00: root bus resource [bus 00] <6>[ 1.854589] pci_bus 0000:00: root bus resource [mem 0x1f8000000-0x1f815ffff] <6>[ 1.861987] pci_bus 0000:00: root bus resource [mem 0x1f8160000-0x1f81cffff pref] <6>[ 1.869764] pci_bus 0000:00: root bus resource [mem 0x1f81d0000-0x1f81effff] <6>[ 1.871186] mmc0: new HS400 MMC card at address 0001 <6>[ 1.877102] pci_bus 0000:00: root bus resource [mem 0x1f81f0000-0x1f820ffff pref] <6>[ 1.877106] pci_bus 0000:00: root bus resource [mem 0x1f8210000-0x1f822ffff] <6>[ 1.882355] usb 3-1: new high-speed USB device number 2 using xhci-hcd <6>[ 1.890117] pci_bus 0000:00: root bus resource [mem 0x1f8230000-0x1f824ffff pref] <6>[ 1.897819] mmcblk0: mmc0:0001 S0J56X 7.34 GiB <6>[ 1.904265] pci_bus 0000:00: root bus resource [mem 0x1fc000000-0x1fc3fffff] <6>[ 1.913568] mmcblk0: p1 p2 <6>[ 1.916863] pci 0000:00:00.0: [1957:e100] type 00 class 0x020001 <6>[ 1.924598] mmcblk0boot0: mmc0:0001 S0J56X 31.5 MiB <6>[ 1.927264] pci 0000:00:00.0: BAR 0: [mem 0x1f8000000-0x1f803ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.934512] mmcblk0boot1: mmc0:0001 S0J56X 31.5 MiB <6>[ 1.938799] pci 0000:00:00.0: BAR 2: [mem 0x1f8160000-0x1f816ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.950350] mmcblk0rpmb: mmc0:0001 S0J56X 4.00 MiB, chardev (234:0) <6>[ 1.954777] pci 0000:00:00.0: VF BAR 0: [mem 0x1f81d0000-0x1f81dffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 1.954784] pci 0000:00:00.0: VF BAR 2: [mem 0x1f81f0000-0x1f81fffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 1.994974] pci 0000:00:00.0: PME# supported from D0 D3hot <6>[ 2.000750] pci 0000:00:00.0: VF(n) BAR0 space: [mem 0x1f81d0000-0x1f81effff 64bit] (contains BAR0 for 2 VFs) <6>[ 2.010967] pci 0000:00:00.0: VF(n) BAR2 space: [mem 0x1f81f0000-0x1f820ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 2.021787] pci 0000:00:00.1: [1957:e100] type 00 class 0x020001 <6>[ 2.028108] pci 0000:00:00.1: BAR 0: [mem 0x1f8040000-0x1f807ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.038850] pci 0000:00:00.1: BAR 2: [mem 0x1f8170000-0x1f817ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.050027] pci 0000:00:00.1: VF BAR 0: [mem 0x1f8210000-0x1f821ffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 2.061028] pci 0000:00:00.1: VF BAR 2: [mem 0x1f8230000-0x1f823ffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 2.072479] pci 0000:00:00.1: PME# supported from D0 D3hot <6>[ 2.078254] pci 0000:00:00.1: VF(n) BAR0 space: [mem 0x1f8210000-0x1f822ffff 64bit] (contains BAR0 for 2 VFs) <6>[ 2.088474] pci 0000:00:00.1: VF(n) BAR2 space: [mem 0x1f8230000-0x1f824ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 2.099262] pci 0000:00:00.2: [1957:e100] type 00 class 0x020001 <6>[ 2.105582] pci 0000:00:00.2: BAR 0: [mem 0x1f8080000-0x1f80bffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.106771] hub 3-1:1.0: USB hub found <6>[ 2.116323] pci 0000:00:00.2: BAR 2: [mem 0x1f8180000-0x1f818ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.120384] hub 3-1:1.0: 7 ports detected <6>[ 2.131528] pci 0000:00:00.2: PME# supported from D0 D3hot <6>[ 2.141696] pci 0000:00:00.3: [1957:ee01] type 00 class 0x088001 <6>[ 2.148020] pci 0000:00:00.3: BAR 0: [mem 0x1f8100000-0x1f811ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.158762] pci 0000:00:00.3: BAR 2: [mem 0x1f8190000-0x1f819ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.169949] pci 0000:00:00.3: PME# supported from D0 D3hot <6>[ 2.175824] pci 0000:00:00.4: [1957:ee02] type 00 class 0x088001 <6>[ 2.182140] pci 0000:00:00.4: BAR 0: [mem 0x1f8120000-0x1f813ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.192883] pci 0000:00:00.4: BAR 2: [mem 0x1f81a0000-0x1f81affff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.204074] pci 0000:00:00.4: PME# supported from D0 D3hot <6>[ 2.209954] pci 0000:00:00.5: [1957:eef0] type 00 class 0x020801 <6>[ 2.216270] pci 0000:00:00.5: BAR 0: [mem 0x1f8140000-0x1f815ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.227012] pci 0000:00:00.5: BAR 2: [mem 0x1f81b0000-0x1f81bffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.238187] pci 0000:00:00.5: BAR 4: [mem 0x1fc000000-0x1fc3fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.248939] pci 0000:00:00.5: PME# supported from D0 D3hot <6>[ 2.254840] pci 0000:00:00.6: [1957:e100] type 00 class 0x020001 <6>[ 2.261158] pci 0000:00:00.6: BAR 0: [mem 0x1f80c0000-0x1f80fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.271903] pci 0000:00:00.6: BAR 2: [mem 0x1f81c0000-0x1f81cffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.283093] pci 0000:00:00.6: PME# supported from D0 D3hot <6>[ 2.289660] pci 0000:00:1f.0: [1957:e001] type 00 class 0x080700 <6>[ 2.295990] OF: /soc/pcie@1f0000000: no msi-map translation for id 0xf8 on (null) <6>[ 2.304003] fsl_enetc 0000:00:00.0: Adding to iommu group 5 <6>[ 2.417195] fsl_enetc 0000:00:00.0: enabling device (0400 -> 0402) <6>[ 2.424581] fsl_enetc 0000:00:00.0: no MAC address specified for SI1, using 9e:68:8b:27:56:06 <6>[ 2.433410] fsl_enetc 0000:00:00.0: no MAC address specified for SI2, using d6:df:ff:a5:b8:6a <6>[ 2.455255] fsl_enetc 0000:00:00.1: Adding to iommu group 6 <6>[ 2.569187] fsl_enetc 0000:00:00.1: enabling device (0400 -> 0402) <6>[ 2.576599] fsl_enetc 0000:00:00.1: device is disabled, skipping <6>[ 2.583031] fsl_enetc 0000:00:00.2: Adding to iommu group 7 <6>[ 2.693170] fsl_enetc 0000:00:00.2: enabling device (0400 -> 0402) <6>[ 2.699981] fsl_enetc 0000:00:00.2: device is disabled, skipping <6>[ 2.706387] fsl_enetc_mdio 0000:00:00.3: Adding to iommu group 8 <6>[ 2.817169] fsl_enetc_mdio 0000:00:00.3: enabling device (0400 -> 0402) <6>[ 2.824380] fsl_enetc_ptp 0000:00:00.4: Adding to iommu group 9 <6>[ 2.830683] fsl_enetc_ptp 0000:00:00.4: enabling device (0404 -> 0406) <4>[ 2.837610] ptp_qoriq: device tree node missing required elements, try automatic configuration <6>[ 2.846639] pps pps0: new PPS source ptp0 <6>[ 2.851173] fsl_enetc 0000:00:00.6: Adding to iommu group 10 <6>[ 2.965183] fsl_enetc 0000:00:00.6: enabling device (0400 -> 0402) <6>[ 2.972010] fsl_enetc 0000:00:00.6: device is disabled, skipping <6>[ 2.978347] OF: /soc/pcie@1f0000000: no iommu-map translation for id 0xf8 on (null) <6>[ 2.986405] pcieport 0000:00:1f.0: PME: Signaling with IRQ 123 <6>[ 2.992996] layerscape-pcie 3400000.pcie: host bridge /soc/pcie@3400000 ranges: <6>[ 3.000629] layerscape-pcie 3400000.pcie: IO 0x8000010000..0x800001ffff -> 0x0000000000 <6>[ 3.009461] layerscape-pcie 3400000.pcie: MEM 0x8040000000..0x807fffffff -> 0x0040000000 <6>[ 3.018320] layerscape-pcie 3400000.pcie: iATU unroll: disabled <6>[ 3.024524] layerscape-pcie 3400000.pcie: Detected iATU regions: 8 outbound, 6 inbound <6>[ 4.033031] layerscape-pcie 3400000.pcie: Phy link never came up <6>[ 4.039680] layerscape-pcie 3400000.pcie: PCI host bridge to bus 0001:00 <6>[ 4.046722] pci_bus 0001:00: root bus resource [bus 00-ff] <6>[ 4.052530] pci_bus 0001:00: root bus resource [io 0x0000-0xffff] <6>[ 4.059037] pci_bus 0001:00: root bus resource [mem 0x8040000000-0x807fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 4.069948] pci 0001:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 4.076423] pci 0001:00:00.0: supports D1 D2 <6>[ 4.081021] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 4.090368] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 4.097306] pci 0001:00:00.0: PCI bridge to [bus 01] <6>[ 4.102727] pcieport 0001:00:00.0: Adding to iommu group 11 <6>[ 4.108866] pcieport 0001:00:00.0: PME: Signaling with IRQ 32 <6>[ 4.115367] layerscape-pcie 3500000.pcie: host bridge /soc/pcie@3500000 ranges: <6>[ 4.123000] layerscape-pcie 3500000.pcie: IO 0x8800010000..0x880001ffff -> 0x0000000000 <6>[ 4.131834] layerscape-pcie 3500000.pcie: MEM 0x8840000000..0x887fffffff -> 0x0040000000 <6>[ 4.140689] layerscape-pcie 3500000.pcie: iATU unroll: disabled <6>[ 4.146898] layerscape-pcie 3500000.pcie: Detected iATU regions: 8 outbound, 6 inbound <6>[ 5.155404] layerscape-pcie 3500000.pcie: Phy link never came up <6>[ 5.162040] layerscape-pcie 3500000.pcie: PCI host bridge to bus 0002:00 <6>[ 5.169079] pci_bus 0002:00: root bus resource [bus 00-ff] <6>[ 5.174900] pci_bus 0002:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) <6>[ 5.184201] pci_bus 0002:00: root bus resource [mem 0x8840000000-0x887fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 5.195111] pci 0002:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 5.201583] pci 0002:00:00.0: supports D1 D2 <6>[ 5.206180] pci 0002:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 5.215468] pci_bus 0002:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 5.222408] pci 0002:00:00.0: PCI bridge to [bus 01] <6>[ 5.227835] pcieport 0002:00:00.0: Adding to iommu group 12 <6>[ 5.234004] pcieport 0002:00:00.0: PME: Signaling with IRQ 34 <6>[ 5.240670] 2270000.serial: ttyLP2 at MMIO 0x2270000 (irq = 25, base_baud = 12500000) is a FSL_LPUART <6>[ 5.252142] spi-nor spi1.0: w25q128fw (16384 Kbytes) <6>[ 5.272632] input: buttons0 as /devices/platform/buttons0/input/input0 <6>[ 5.343039] fsl_enetc 0000:00:00.0 eth0: PHY [0000:00:00.0:05] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL) <6>[ 5.380700] fsl_enetc 0000:00:00.0 eth0: configuring for inband/sgmii link mode <6>[ 8.454090] fsl_enetc 0000:00:00.0 eth0: Link is Up - 1Gbps/Full - flow control rx/tx <5>[ 8.481201] Sending DHCP requests ., OK <6>[ 8.501452] IP-Config: Got DHCP answer from 172.16.0.254, my address is 172.16.0.64 <6>[ 8.509459] IP-Config: Complete: <6>[ 8.512967] device=eth0, hwaddr=00:e0:4b:6e:9b:2b, ipaddr=172.16.0.64, mask=255.255.255.0, gw=172.16.0.254 <6>[ 8.523415] host=172.16.0.64, domain=lava.lan, nis-domain=(none) <6>[ 8.530181] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 8.530197] nameserver0=8.8.8.8 <6>[ 8.540935] clk: Disabling unused clocks <6>[ 8.545291] ALSA device list: <6>[ 8.548534] No soundcards found. <6>[ 8.555729] Freeing unused kernel memory: 6208K <6>[ 8.560765] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 8.618137] udevd[95]: starting version 3.2.9 <5>[ 8.623285] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.630207] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.636970] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 8.646424] udevd[95]: specified user 'tss' unknown <27>[ 8.651774] udevd[95]: specified group 'tss' unknown <30>[ 8.657972] udevd[96]: starting eudev-3.2.9 <6>[ 8.850405] EDAC MC0: Giving out device to module fsl_ddr_edac controller fsl_mc_err: DEV fsl_mc_err (INTERRUPT) <6>[ 8.864855] fsl_ddr_edac acquired irq 15 for MC <27>[ 8.869457] udevd[104]: Error changing net interface name eth0 to enp0s0f0: Device or resource busy <6>[ 8.873346] fsl_ddr_edac MC err registered <28>[ 8.901303] udevd[104]: could not rename interface '2' from 'eth0' to 'enp0s0f0': Device or resource busy <6>[ 8.913460] mali-dp f080000.display: Adding to iommu group 13 <4>[ 8.919944] rtc-rv8803 0-0032: Voltage low, temperature compensation stopped. <4>[ 8.927448] rtc-rv8803 0-0032: Voltage low, data loss detected. <4>[ 8.936869] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 8.949299] NET: Registered PF_INET6 protocol family <6>[ 8.956400] at24 0-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 8.966264] at24 1-0057: supply vcc not found, using dummy regulator <6>[ 8.973564] Segment Routing with IPv6 <6>[ 8.977581] In-situ OAM (IOAM) with IPv6 <4>[ 8.977859] wm8904 2-001a: supply DCVDD not found, using dummy regulator <4>[ 8.990801] rtc-rv8803 0-0032: Voltage low, data is invalid. <6>[ 8.999319] at24 1-0057: 8192 byte 24c64 EEPROM, writable, 32 bytes/write <6>[ 9.007427] sl28cpld-wdt 2000000.i2c:sl28cpld@4a:watchdog@4: initial timeout 6 sec <6>[ 9.013190] rtc-rv8803 0-0032: registered as rtc0 <4>[ 9.020457] wm8904 2-001a: supply DBVDD not found, using dummy regulator <4>[ 9.027609] at24 2-0050: supply vcc not found, using dummy regulator <4>[ 9.027648] wm8904 2-001a: supply AVDD not found, using dummy regulator <6>[ 9.041564] mscc_felix 0000:00:00.5: Adding to iommu group 14 <6>[ 9.048101] at24 2-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 9.055922] wm8904 2-001a: supply CPVDD not found, using dummy regulator <6>[ 9.061349] mscc_felix 0000:00:00.5: device is disabled, skipping <4>[ 9.063788] wm8904 2-001a: supply MICVDD not found, using dummy regulator <4>[ 9.076803] rtc-rv8803 0-0032: Voltage low, data is invalid. <3>[ 9.084581] rtc-rv8803 0-0032: hctosys: unable to read the hardware clock <6>[ 9.092310] CAN device driver interface <6>[ 9.093625] wm8904 2-001a: revision A <6>[ 9.138907] ftm-alarm 2800000.timer: registered as rtc1 <6>[ 9.154847] caam 8000000.crypto: Entropy delay = 3200 <6>[ 9.200020] caam 8000000.crypto: Instantiated RNG4 SH0 <6>[ 9.218758] caam 8000000.crypto: Instantiated RNG4 SH1 <6>[ 9.224544] caam 8000000.crypto: device ID = 0x0a12070000000000 (Era 10) <6>[ 9.235064] caam 8000000.crypto: job rings = 4, qi = 0 <6>[ 9.267963] caam_jr 8010000.jr: Adding to iommu group 15 <6>[ 9.274236] caam algorithms registered in /proc/crypto <6>[ 9.279741] caam 8000000.crypto: registering rng-caam <6>[ 9.285352] caam_jr 8020000.jr: Adding to iommu group 16 <6>[ 9.291319] caam_jr 8030000.jr: Adding to iommu group 17 <6>[ 9.297301] caam_jr 8040000.jr: Adding to iommu group 18 done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: <5>[ 9.345365] random: crng init done can't access tty<5>[ 9.349387] random: 4 urandom warning(s) missed due to ratelimiting ; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-514093/environment . /lava-514093/environment / # /lava-514093/bin/lava-test-runner /lava-514093/0 /lava-514093/bin/lava-test-runner /lava-514093/0 + export 'TESTRUN_ID=0_dmesg' + c<8>[ 9.898215] d /lava-514093/0/tests/0_dmesg + cat uuid + UUID=514093_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 9.917624] <8>[ 9.937445] <8>[ 9.957548] + set +x <8>[ 9.966905] / #