Trying 0.0.0.0... Connected to 0. Escape character is '^]'. U-Boot SPL 2021.10 (Oct 25 2021 - 13:39:59 +0200) Trying to boot from SPI U-Boot 2021.10 (Oct 25 2021 - 13:39:59 +0200) SoC: LS1028A Rev1.0 (0x870b0110) Clock Configuration: CPU0(A72):1300 MHz CPU1(A72):1300 MHz Bus: 400 MHz DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 34004010 00000030 00000000 00000000 00000010: 00000000 008f0000 0030c000 00000000 00000020: 06200000 00002580 00000000 00019016 00000030: 00000000 00000048 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000304 00000000 000e7000 00000000 00000070: bb580000 00020000 Model: Kontron SMARC-sAL28 (Dual PHY) EL: 3 DRAM: 4 GiB DDR 4 GiB (DDR3, 32-bit, CL=11, ECC on) SEC0: RNG instantiated CPU: 2 cores online Using SERDES1 Protocol: 47960 (0xbb58) MMC: FSL_SDHC: 1, FSL_SDHC: 0 Loading Environment from SPIFlash... SF: Detected w25q32dw with page size 256 Bytes, erase size 64 KiB, total 4 MiB OK PCIe1: pcie@3400000 Root Complex: no link PCIe2: pcie@3500000 Root Complex: no link In: serial@21c0500 Out: serial@21c0500 Err: serial@21c0500 Net: eth0: enetc-0, eth1: enetc-1 Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => dhcp dhcp enetc-0 Waiting for PHY auto negotiation to complete.... done BOOTP broadcast 1 BOOTP broadcast 2 DHCP client bound to address 172.16.0.117 (255 ms) => setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 => tftp 0x82000000 494875/tftp-deploy-repeghvg/kernel/Image tftp 0x82000000 494875/tftp-deploy-repeghvg/kernel/Image Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.117; sending through gateway 172.16.0.254 Filename '494875/tftp-deploy-repeghvg/kernel/Image'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################### 5.8 MiB/s done Bytes transferred = 35265024 (21a1a00 hex) => tftp 0x90080000 494875/tftp-deploy-repeghvg/ramdisk/ramdisk.cpio.gz.uboot tftp 0x90080000 494875/tftp-deploy-repeghvg/ramdisk/ramdisk.cpio.gz.uboot Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.117; sending through gateway 172.16.0.254 Filename '494875/tftp-deploy-repeghvg/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x90080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################## 11.7 MiB/s done Bytes transferred = 24751950 (179af4e hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 494875/tftp-deploy-repeghvg/dtb/fsl-ls1028a-kontron-kbox-a-230-ls.dtb tftp 0x90000000 494875/tftp-deploy-repeghvg/dtb/fsl-ls1028a-kontron-kbox-a-230-ls.dtb Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.117; sending through gateway 172.16.0.254 Filename '494875/tftp-deploy-repeghvg/dtb/fsl-ls1028a-kontron-kbox-a-230-ls.dtb'. Load address: 0x90000000 Loading: *### 5.6 MiB/s done Bytes transferred = 29429 (72f5 hex) => setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => booti 0x82000000 0x90080000 0x90000000 booti 0x82000000 0x90080000 0x90000000 ## Loading init Ramdisk from Legacy Image at 90080000 ... Image Name: Created: 2024-09-06 17:09:47 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 24751886 Bytes = 23.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Using Device Tree in place at 0000000090000000, end 000000009000a2f4 WARNING could not find node fsl,ls1028a-gpu: FDT_ERR_NOTFOUND. Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [ 0.000000] Linux version 6.6.48 (KernelCI@build-j310443-arm64-clang-17-defconfig-config-randomize-baw69hv) (Debian clang version 17.0.6 (++20231208085813+6009708b4367-1~exp1~20231208085906.81), Debian LLD 17.0.6) #1 SMP PREEMPT Fri Sep 6 16:45:19 UTC 2024 [ 0.000000] KASLR disabled due to lack of seed [ 0.000000] Machine model: Kontron KBox A-230-LS [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: ns16550a0 at MMIO 0x00000000021c0500 (options '115200n8') [ 0.000000] printk: bootconsole [ns16550a0] enabled [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x20ff7d2740-0x20ff7d5fff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000020ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] NoSplit zone start for each node [ 0.000000] NoMerge zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] node 0: [mem 0x0000002080000000-0x00000020ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] cma: Reserved 32 MiB at 0x00000000fcc00000 on node -1 [ 0.000000] percpu: Embedded 22 pages/cpu s52200 r8192 d29720 u90112 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: Spectre-v3a [ 0.000000] CPU features: detected: Spectre-v4 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: detected: ARM erratum 1742098 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <5>[ 0.000000] Unknown kernel command line parameters \"n8\", will be passed to user space. <6>[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] Fallback order for Node 0: 0 <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1032192 <6>[ 0.000000] Policy zone: Normal <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] software IO TLB: area num 2. <6>[ 0.000000] software IO TLB: mapped [mem 0x00000000f8c00000-0x00000000fcc00000] (64MB) <6>[ 0.000000] Memory: 3955648K/4194304K available (17216K kernel code, 4486K rwdata, 10436K rodata, 2112K init, 643K bss, 205888K reserved, 32768K cma-reserved) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=2. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode <6>[ 0.000000] GICv3: 256 SPIs implemented <6>[ 0.000000] GICv3: 0 Extended SPIs implemented <6>[ 0.000000] Root IRQ handler: gic_handle_irq <6>[ 0.000000] GICv3: GICv3 features: 16 PPIs <6>[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006040000 <6>[ 0.000000] ITS [mem 0x06020000-0x0603ffff] <6>[ 0.000000] ITS@0x0000000006020000: allocated 65536 Devices @2080080000 (flat, esz 8, psz 64K, shr 0) <6>[ 0.000000] ITS: using cache flushing for cmd queue <6>[ 0.000000] GICv3: using LPI property table @0x0000002080030000 <6>[ 0.000000] GIC: using cache flushing for LPI property table <6>[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000002080040000 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns <6>[ 0.000000] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns <6>[ 0.008823] Console: colour dummy device 80x25 <6>[ 0.013617] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) <6>[ 0.024337] pid_max: default: 32768 minimum: 301 <6>[ 0.029298] LSM: initializing lsm=capability,integrity <6>[ 0.034819] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.042566] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.051749] RCU Tasks: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1. <6>[ 0.059193] RCU Tasks Trace: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1. <6>[ 0.067233] rcu: Hierarchical SRCU implementation. <6>[ 0.072334] rcu: Max phase no-delay instances is 1000. <6>[ 0.078024] Platform MSI: msi-controller@6020000 domain created <6>[ 0.084351] PCI/MSI: /interrupt-controller@6000000/msi-controller@6020000 domain created <6>[ 0.092836] fsl-mc MSI: msi-controller@6020000 domain created <6>[ 0.099717] EFI services will not be available. <6>[ 0.104661] smp: Bringing up secondary CPUs ... <6>[ 0.109791] Detected PIPT I-cache on CPU1 <6>[ 0.109829] GICv3: CPU1: found redistributor 1 region 0:0x0000000006060000 <6>[ 0.109839] GICv3: CPU1: using allocated LPI pending table @0x0000002080050000 <6>[ 0.109863] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] <6>[ 0.109926] smp: Brought up 1 node, 2 CPUs <6>[ 0.140240] SMP: Total of 2 processors activated. <6>[ 0.145252] CPU features: detected: 32-bit EL0 Support <6>[ 0.150709] CPU features: detected: 32-bit EL1 Support <6>[ 0.156161] CPU features: detected: CRC32 instructions <6>[ 0.161655] CPU: All CPU(s) started at EL2 <6>[ 0.166070] alternatives: applying system-wide alternatives <6>[ 0.173258] devtmpfs: initialized <6>[ 0.180729] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.190851] futex hash table entries: 512 (order: 3, 32768 bytes, linear) <6>[ 0.198545] pinctrl core: initialized pinctrl subsystem <6>[ 0.204578] Machine: Kontron KBox A-230-LS <6>[ 0.208976] SoC family: QorIQ LS1028A <6>[ 0.212930] SoC ID: svr:0x870b0110, Revision: 1.0 <6>[ 0.218190] DMI not present or invalid. <6>[ 0.222766] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.229524] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.237019] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.245138] audit: initializing netlink subsys (disabled) <5>[ 0.250948] audit: type=2000 audit(0.152:1): state=initialized audit_enabled=0 res=1 <6>[ 0.251635] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.259039] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.265400] cpuidle: using governor menu <6>[ 0.276603] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.283749] ASID allocator initialised with 65536 entries <6>[ 0.290652] Serial: AMBA PL011 UART driver <6>[ 0.305654] Modules: 23984 pages in range for non-PLT usage <6>[ 0.305661] Modules: 515504 pages in range for PLT usage <6>[ 0.311994] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.324736] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page <6>[ 0.331328] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.338443] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page <6>[ 0.345032] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.352147] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page <6>[ 0.358736] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.365850] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page <6>[ 0.373550] ACPI: Interpreter disabled. <6>[ 0.379165] iommu: Default domain type: Translated <6>[ 0.384262] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.390933] SCSI subsystem initialized <6>[ 0.395195] usbcore: registered new interface driver usbfs <6>[ 0.401022] usbcore: registered new interface driver hub <6>[ 0.406667] usbcore: registered new device driver usb <6>[ 0.412353] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.420200] i2c i2c-0: IMX I2C adapter registered <6>[ 0.425421] imx-i2c 2030000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.433091] i2c i2c-1: IMX I2C adapter registered <6>[ 0.438213] imx-i2c 2040000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.445872] i2c i2c-2: IMX I2C adapter registered <6>[ 0.451263] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.456542] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.466044] PTP clock support registered <6>[ 0.470368] EDAC MC: Ver: 3.0.0 <6>[ 0.474167] scmi_core: SCMI protocol bus registered <6>[ 0.479794] FPGA manager framework <6>[ 0.483547] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.490474] vgaarb: loaded <6>[ 0.493701] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.500264] VFS: Disk quotas dquot_6.6.0 <6>[ 0.504509] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 0.511813] pnp: PnP ACPI: disabled <6>[ 0.519816] NET: Registered PF_INET protocol family <6>[ 0.525180] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 0.534849] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear) <6>[ 0.543784] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.551878] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) <6>[ 0.560227] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes, linear) <6>[ 0.568577] TCP: Hash tables configured (established 32768 bind 32768) <6>[ 0.575532] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.582602] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.590187] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.596477] RPC: Registered named UNIX socket transport module. <6>[ 0.602726] RPC: Registered udp transport module. <6>[ 0.607736] RPC: Registered tcp transport module. <6>[ 0.612746] RPC: Registered tcp-with-tls transport module. <6>[ 0.618551] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.625324] PCI: CLS 0 bytes, default 64 <6>[ 0.629717] kvm [1]: IPA Size Limit: 44 bits <6>[ 0.629732] Unpacking initramfs... <6>[ 0.637992] kvm [1]: GICv3: no GICV resource entry <6>[ 0.637996] kvm [1]: disabling GICv2 emulation <6>[ 0.643093] kvm [1]: GIC system register CPU interface enabled <6>[ 0.643108] kvm [1]: vgic interrupt IRQ9 <6>[ 0.658243] kvm [1]: Hyp mode initialized successfully <5>[ 0.666158] Initialise system trusted keyrings <6>[ 0.671058] workingset: timestamp_bits=42 max_order=20 bucket_order=0 <6>[ 0.678071] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.684430] NFS: Registering the id_resolver key type <5>[ 0.689811] Key type id_resolver registered <5>[ 0.694300] Key type id_legacy registered <6>[ 0.698627] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.705661] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 0.713514] 9p: Installing v9fs 9p2000 file system support <6>[ 0.731471] jitterentropy: Initialization failed with host not compliant with requirements: 9 <5>[ 0.740365] Key type asymmetric registered <5>[ 0.744778] Asymmetric key parser 'x509' registered <6>[ 0.750024] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 0.757767] io scheduler mq-deadline registered <6>[ 0.762613] io scheduler kyber registered <6>[ 0.766965] io scheduler bfq registered <6>[ 0.778267] pci-host-generic 1f0000000.pcie: host bridge /soc/pcie@1f0000000 ranges: <6>[ 0.786425] pci-host-generic 1f0000000.pcie: MEM 0x01f8000000..0x01f815ffff -> 0x01f8000000 <6>[ 0.795605] pci-host-generic 1f0000000.pcie: MEM 0x01f8160000..0x01f81cffff -> 0x01f8160000 <6>[ 0.804780] pci-host-generic 1f0000000.pcie: MEM 0x01f81d0000..0x01f81effff -> 0x01f81d0000 <6>[ 0.813948] pci-host-generic 1f0000000.pcie: MEM 0x01f81f0000..0x01f820ffff -> 0x01f81f0000 <6>[ 0.823116] pci-host-generic 1f0000000.pcie: MEM 0x01f8210000..0x01f822ffff -> 0x01f8210000 <6>[ 0.832284] pci-host-generic 1f0000000.pcie: MEM 0x01f8230000..0x01f824ffff -> 0x01f8230000 <6>[ 0.841452] pci-host-generic 1f0000000.pcie: MEM 0x01fc000000..0x01fc3fffff -> 0x01fc000000 <6>[ 0.850685] pci-host-generic 1f0000000.pcie: ECAM at [mem 0x1f0000000-0x1f00fffff] for [bus 00] <6>[ 0.859959] pci-host-generic 1f0000000.pcie: PCI host bridge to bus 0000:00 <6>[ 0.867282] pci_bus 0000:00: root bus resource [bus 00] <6>[ 0.872837] pci_bus 0000:00: root bus resource [mem 0x1f8000000-0x1f815ffff] <6>[ 0.880237] pci_bus 0000:00: root bus resource [mem 0x1f8160000-0x1f81cffff pref] <6>[ 0.888074] pci_bus 0000:00: root bus resource [mem 0x1f81d0000-0x1f81effff] <6>[ 0.895470] pci_bus 0000:00: root bus resource [mem 0x1f81f0000-0x1f820ffff pref] <6>[ 0.903304] pci_bus 0000:00: root bus resource [mem 0x1f8210000-0x1f822ffff] <6>[ 0.910704] pci_bus 0000:00: root bus resource [mem 0x1f8230000-0x1f824ffff pref] <6>[ 0.918539] pci_bus 0000:00: root bus resource [mem 0x1fc000000-0x1fc3fffff] <6>[ 0.925958] pci 0000:00:00.0: [1957:e100] type 00 class 0x020001 <6>[ 0.932328] pci 0000:00:00.0: BAR 0: [mem 0x1f8000000-0x1f803ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 0.943151] pci 0000:00:00.0: BAR 2: [mem 0x1f8160000-0x1f816ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 0.954417] pci 0000:00:00.0: VF BAR 0: [mem 0x1f81d0000-0x1f81dffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 0.965506] pci 0000:00:00.0: VF BAR 2: [mem 0x1f81f0000-0x1f81fffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 0.977056] pci 0000:00:00.0: PME# supported from D0 D3hot <6>[ 0.982881] pci 0000:00:00.0: VF(n) BAR0 space: [mem 0x1f81d0000-0x1f81effff 64bit] (contains BAR0 for 2 VFs) <6>[ 0.993186] pci 0000:00:00.0: VF(n) BAR2 space: [mem 0x1f81f0000-0x1f820ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 1.004132] pci 0000:00:00.1: [1957:e100] type 00 class 0x020001 <6>[ 1.010515] pci 0000:00:00.1: BAR 0: [mem 0x1f8040000-0x1f807ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.021339] pci 0000:00:00.1: BAR 2: [mem 0x1f8170000-0x1f817ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.032596] pci 0000:00:00.1: VF BAR 0: [mem 0x1f8210000-0x1f821ffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 1.043690] pci 0000:00:00.1: VF BAR 2: [mem 0x1f8230000-0x1f823ffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 1.055226] pci 0000:00:00.1: PME# supported from D0 D3hot <6>[ 1.061044] pci 0000:00:00.1: VF(n) BAR0 space: [mem 0x1f8210000-0x1f822ffff 64bit] (contains BAR0 for 2 VFs) <6>[ 1.071334] pci 0000:00:00.1: VF(n) BAR2 space: [mem 0x1f8230000-0x1f824ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 1.082273] pci 0000:00:00.2: [1957:e100] type 00 class 0x020001 <6>[ 1.088653] pci 0000:00:00.2: BAR 0: [mem 0x1f8080000-0x1f80bffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.099481] pci 0000:00:00.2: BAR 2: [mem 0x1f8180000-0x1f818ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.110762] pci 0000:00:00.2: PME# supported from D0 D3hot <6>[ 1.116749] pci 0000:00:00.3: [1957:ee01] type 00 class 0x088001 <6>[ 1.123123] pci 0000:00:00.3: BAR 0: [mem 0x1f8100000-0x1f811ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.133946] pci 0000:00:00.3: BAR 2: [mem 0x1f8190000-0x1f819ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.145214] pci 0000:00:00.3: PME# supported from D0 D3hot <6>[ 1.151220] pci 0000:00:00.4: [1957:ee02] type 00 class 0x088001 <6>[ 1.157579] pci 0000:00:00.4: BAR 0: [mem 0x1f8120000-0x1f813ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.168411] pci 0000:00:00.4: BAR 2: [mem 0x1f81a0000-0x1f81affff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.179694] pci 0000:00:00.4: PME# supported from D0 D3hot <6>[ 1.185741] pci 0000:00:00.5: [1957:eef0] type 00 class 0x020801 <6>[ 1.192103] pci 0000:00:00.5: BAR 0: [mem 0x1f8140000-0x1f815ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.202930] pci 0000:00:00.5: BAR 2: [mem 0x1f81b0000-0x1f81bffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.214193] pci 0000:00:00.5: BAR 4: [mem 0x1fc000000-0x1fc3fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.225031] pci 0000:00:00.5: PME# supported from D0 D3hot <6>[ 1.231059] pci 0000:00:00.6: [1957:e100] type 00 class 0x020001 <6>[ 1.237438] pci 0000:00:00.6: BAR 0: [mem 0x1f80c0000-0x1f80fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.248274] pci 0000:00:00.6: BAR 2: [mem 0x1f81c0000-0x1f81cffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.259550] pci 0000:00:00.6: PME# supported from D0 D3hot <6>[ 1.266263] pci 0000:00:1f.0: [1957:e001] type 00 class 0x080700 <6>[ 1.272661] OF: /soc/pcie@1f0000000: no msi-map translation for id 0xf8 on (null) <6>[ 1.280734] OF: /soc/pcie@1f0000000: no iommu-map translation for id 0xf8 on (null) <6>[ 1.288914] pcieport 0000:00:1f.0: PME: Signaling with IRQ 19 <6>[ 1.295238] pcieport 0000:00:1f.0: AER: enabled with IRQ 19 <6>[ 1.301985] layerscape-pcie 3400000.pcie: host bridge /soc/pcie@3400000 ranges: <6>[ 1.309681] layerscape-pcie 3400000.pcie: IO 0x8000010000..0x800001ffff -> 0x0000000000 <6>[ 1.318601] layerscape-pcie 3400000.pcie: MEM 0x8040000000..0x807fffffff -> 0x0040000000 <6>[ 1.327539] layerscape-pcie 3400000.pcie: iATU: unroll F, 8 ob, 6 ib, align 4K, limit 4G <6>[ 1.538853] Freeing initrd memory: 24164K <6>[ 2.329793] layerscape-pcie 3400000.pcie: Phy link never came up <6>[ 2.336263] layerscape-pcie 3400000.pcie: PCI host bridge to bus 0001:00 <6>[ 2.343299] pci_bus 0001:00: root bus resource [bus 00-ff] <6>[ 2.349105] pci_bus 0001:00: root bus resource [io 0x0000-0xffff] <6>[ 2.355610] pci_bus 0001:00: root bus resource [mem 0x8040000000-0x807fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 2.366524] pci 0001:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 2.372912] pci 0001:00:00.0: supports D1 D2 <6>[ 2.377486] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 2.384799] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 2.391753] pci 0001:00:00.0: PCI bridge to [bus 01] <6>[ 2.397181] layerscape-pcie 3500000.pcie: host bridge /soc/pcie@3500000 ranges: <6>[ 2.404860] layerscape-pcie 3500000.pcie: IO 0x8800010000..0x880001ffff -> 0x0000000000 <6>[ 2.413749] layerscape-pcie 3500000.pcie: MEM 0x8840000000..0x887fffffff -> 0x0040000000 <6>[ 2.422662] layerscape-pcie 3500000.pcie: iATU: unroll F, 8 ob, 6 ib, align 4K, limit 4G <6>[ 3.431199] layerscape-pcie 3500000.pcie: Phy link never came up <6>[ 3.437594] layerscape-pcie 3500000.pcie: PCI host bridge to bus 0002:00 <6>[ 3.444628] pci_bus 0002:00: root bus resource [bus 00-ff] <6>[ 3.450431] pci_bus 0002:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) <6>[ 3.459745] pci_bus 0002:00: root bus resource [mem 0x8840000000-0x887fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 3.470653] pci 0002:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 3.477037] pci 0002:00:00.0: supports D1 D2 <6>[ 3.481611] pci 0002:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 3.488836] pci_bus 0002:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 3.495791] pci 0002:00:00.0: PCI bridge to [bus 01] <6>[ 3.501932] EINJ: ACPI disabled. <6>[ 3.522223] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 3.530868] printk: console [ttyS0] disabled <6>[ 3.535652] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 20, base_baud = 12500000) is a 16550A <6>[ 3.544815] printk: console [ttyS0] enabled <6>[ 3.544815] printk: console [ttyS0] enabled <6>[ 3.553757] printk: bootconsole [ns16550a0] disabled <6>[ 3.553757] printk: bootconsole [ns16550a0] disabled <6>[ 3.566262] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 20, base_baud = 12500000) is a 16550A <6>[ 3.575742] SuperH (H)SCI(F) driver initialized <6>[ 3.580874] msm_serial: driver initialized <6>[ 3.585827] 2270000.serial: ttyLP2 at MMIO 0x2270000 (irq = 21, base_baud = 12500000) is a FSL_LPUART <6>[ 3.595712] STM32 USART driver initialized <5>[ 3.603113] arm-smmu 5000000.iommu: probing hardware configuration... <5>[ 3.609847] arm-smmu 5000000.iommu: SMMUv2 with: <5>[ 3.614744] arm-smmu 5000000.iommu: stage 1 translation <5>[ 3.620337] arm-smmu 5000000.iommu: stage 2 translation <5>[ 3.625930] arm-smmu 5000000.iommu: nested translation <5>[ 3.631435] arm-smmu 5000000.iommu: coherent table walk <5>[ 3.637028] arm-smmu 5000000.iommu: (IDR0.CTTW overridden by FW configuration) <5>[ 3.644630] arm-smmu 5000000.iommu: stream matching with 128 register groups <5>[ 3.652057] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) <5>[ 3.658878] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 <5>[ 3.665605] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA <5>[ 3.672331] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA <5>[ 3.679287] arm-smmu 5000000.iommu: preserved 0 boot mappings <4>[ 3.685457] arm-smmu 5000000.iommu: Failed to disable prefetcher [errata #841119 and #826419], check ACR.CACHE_LOCK <6>[ 3.699585] loop: module loaded <6>[ 3.710907] megasas: 07.725.01.00-rc1 <6>[ 3.715617] ahci-qoriq 3200000.sata: Adding to iommu group 0 <4>[ 3.721661] ahci-qoriq 3200000.sata: supply ahci not found, using dummy regulator <4>[ 3.729520] ahci-qoriq 3200000.sata: supply phy not found, using dummy regulator <4>[ 3.737236] ahci-qoriq 3200000.sata: supply target not found, using dummy regulator <6>[ 3.745312] ahci-qoriq 3200000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode <6>[ 3.754579] ahci-qoriq 3200000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst <6>[ 3.764994] scsi host0: ahci-qoriq <6>[ 3.768809] ata1: SATA max UDMA/133 mmio [mem 0x03200000-0x0320ffff] port 0x100 irq 95 <6>[ 3.779412] spi-nor spi0.0: w25q32dw (4096 Kbytes) <6>[ 4.091922] ata1: SATA link down (SStatus 0 SControl 300) <5>[ 4.111411] 5 fixed-partitions partitions found on MTD device 20c0000.spi <5>[ 4.118533] Creating 5 MTD partitions on \"20c0000.spi\": <5>[ 4.124043] 0x000000000000-0x000000010000 : \"rcw\" <5>[ 4.129792] 0x000000010000-0x0000001e0000 : \"failsafe bootloader\" <5>[ 4.136938] 0x000000200000-0x000000210000 : \"configuration store\" <5>[ 4.143938] 0x000000210000-0x0000003e0000 : \"bootloader\" <5>[ 4.150179] 0x0000003e0000-0x000000400000 : \"bootloader environment\" <6>[ 4.160444] tun: Universal TUN/TAP device driver, 1.6 <6>[ 4.166428] thunder_xcv, ver 1.0 <6>[ 4.169961] thunder_bgx, ver 1.0 <6>[ 4.173477] nicpf, ver 1.0 <6>[ 4.177034] fsl_enetc 0000:00:00.0: Adding to iommu group 1 <6>[ 4.183122] fsl_enetc 0000:00:00.1: Adding to iommu group 2 <6>[ 4.189145] fsl_enetc 0000:00:00.2: Adding to iommu group 3 <6>[ 4.195160] fsl_enetc 0000:00:00.6: Adding to iommu group 4 <6>[ 4.201388] fsl_enetc_mdio 0000:00:00.3: Adding to iommu group 5 <6>[ 4.313713] fsl_enetc_mdio 0000:00:00.3: enabling device (0400 -> 0402) <6>[ 4.350768] mdio_bus 0000:00:00.3:04: Fixed dependency cycle(s) with /soc/pcie@1f0000000/mdio@0,3/ethernet-phy@4/vddio-regulator <6>[ 4.428840] fsl_enetc_ptp 0000:00:00.4: Adding to iommu group 6 <6>[ 4.435149] fsl_enetc_ptp 0000:00:00.4: enabling device (0404 -> 0406) <4>[ 4.442170] ptp_qoriq: device tree node missing required elements, try automatic configuration <6>[ 4.451204] pps pps0: new PPS source ptp0 <6>[ 4.455998] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 4.463519] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 4.469146] hclge is initializing <6>[ 4.472751] e1000: Intel(R) PRO/1000 Network Driver <6>[ 4.477906] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 4.483956] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 4.489199] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 4.495423] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 4.501103] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 4.506976] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 4.513527] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 4.519952] sky2: driver version 1.30 <6>[ 4.524774] VFIO - User Level meta-driver version: 0.3 <6>[ 4.530519] dwc3 3100000.usb: Adding to iommu group 7 <6>[ 4.536769] dwc3 3110000.usb: Adding to iommu group 8 <6>[ 4.544399] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 4.550196] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 <6>[ 4.558271] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000808002000010 <6>[ 4.567990] xhci-hcd xhci-hcd.0.auto: irq 100, io mem 0x03110000 <6>[ 4.574377] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 4.580149] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 <6>[ 4.588100] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed <6>[ 4.595297] hub 1-0:1.0: USB hub found <6>[ 4.599340] hub 1-0:1.0: 1 port detected <6>[ 4.603729] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 4.612392] hub 2-0:1.0: USB hub found <6>[ 4.616435] hub 2-0:1.0: 1 port detected <6>[ 4.621160] usbcore: registered new interface driver usb-storage <6>[ 4.629537] i2c_dev: i2c /dev entries driver <6>[ 4.637467] sp805-wdt c000000.watchdog: registration successful <6>[ 4.643821] sp805-wdt c010000.watchdog: registration successful <6>[ 4.652037] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver <6>[ 4.660902] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.667380] sdhci: Copyright(c) Pierre Ossman <6>[ 4.672514] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.679453] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.685993] sdhci-esdhc 2140000.mmc: Adding to iommu group 9 <6>[ 4.692085] sdhci-esdhc 2150000.mmc: Adding to iommu group 10 <6>[ 4.698570] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.706678] usbcore: registered new interface driver usbhid <6>[ 4.712548] usbhid: USB HID core driver <6>[ 4.717732] mmc1: SDHCI controller on 2140000.mmc [2140000.mmc] using ADMA <6>[ 4.724934] mmc0: SDHCI controller on 2150000.mmc [2150000.mmc] using ADMA <6>[ 4.725051] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available <6>[ 4.744491] NET: Registered PF_PACKET protocol family <6>[ 4.749896] 9pnet: Installing 9P2000 support <5>[ 4.754480] Key type dns_resolver registered <6>[ 4.765527] registered taskstats version 1 <5>[ 4.770049] Loading compiled-in X.509 certificates <6>[ 4.783495] fsl-edma 22c0000.dma-controller: Adding to iommu group 11 <6>[ 4.791504] pcieport 0001:00:00.0: Adding to iommu group 12 <6>[ 4.797557] pcieport 0001:00:00.0: PME: Signaling with IRQ 105 <6>[ 4.803917] pcieport 0001:00:00.0: AER: enabled with IRQ 105 <6>[ 4.810073] pcieport 0002:00:00.0: Adding to iommu group 13 <6>[ 4.816115] pcieport 0002:00:00.0: PME: Signaling with IRQ 106 <6>[ 4.822412] pcieport 0002:00:00.0: AER: enabled with IRQ 106 <6>[ 4.849180] mmc0: new HS400 MMC card at address 0001 <6>[ 4.854853] mmcblk0: mmc0:0001 S0J58X 29.6 GiB <6>[ 4.860869] mmcblk0: p1 p2 p3 <6>[ 4.864226] usb 1-1: new high-speed USB device number 2 using xhci-hcd <6>[ 4.871628] mmcblk0boot0: mmc0:0001 S0J58X 31.5 MiB <6>[ 4.877803] mmcblk0boot1: mmc0:0001 S0J58X 31.5 MiB <6>[ 4.883813] mmcblk0rpmb: mmc0:0001 S0J58X 4.00 MiB, chardev (234:0) <6>[ 4.933719] fsl_enetc 0000:00:00.0: enabling device (0400 -> 0402) <6>[ 4.941247] fsl_enetc 0000:00:00.0: no MAC address specified for SI1, using 06:a3:a6:65:2f:0e <6>[ 4.950137] fsl_enetc 0000:00:00.0: no MAC address specified for SI2, using e2:6b:08:e6:7d:1b <6>[ 5.065775] fsl_enetc 0000:00:00.1: enabling device (0400 -> 0402) <6>[ 5.073288] fsl_enetc 0000:00:00.1: no MAC address specified for SI1, using 76:9c:e6:35:41:db <6>[ 5.075343] hub 1-1:1.0: USB hub found <6>[ 5.082192] fsl_enetc 0000:00:00.1: no MAC address specified for SI2, using 92:ba:d5:d2:9c:2c <6>[ 5.086238] hub 1-1:1.0: 7 ports detected <6>[ 5.201733] fsl_enetc 0000:00:00.2: enabling device (0400 -> 0402) <6>[ 5.317795] fsl_enetc 0000:00:00.6: enabling device (0400 -> 0402) <6>[ 5.334826] input: buttons0 as /devices/platform/buttons0/input/input0 <6>[ 5.407560] fsl_enetc 0000:00:00.0 eth0: PHY [0000:00:00.3:05] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL) <6>[ 5.419298] fsl_enetc 0000:00:00.0 eth0: configuring for inband/sgmii link mode <6>[ 5.425769] usb 1-1.6: new full-speed USB device number 3 using xhci-hcd <6>[ 5.483960] fsl_enetc 0000:00:00.1 eth1: PHY [0000:00:00.3:04] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL) <6>[ 5.495590] fsl_enetc 0000:00:00.1 eth1: configuring for phy/rgmii-id link mode <6>[ 5.520414] fsl_enetc 0000:00:00.2 eth2: configuring for fixed/internal link mode <6>[ 5.528309] fsl_enetc 0000:00:00.2 eth2: Link is Up - 2.5Gbps/Full - flow control rx/tx <6>[ 5.544061] fsl_enetc 0000:00:00.6 eth3: configuring for fixed/internal link mode <6>[ 5.551911] fsl_enetc 0000:00:00.6 eth3: Link is Up - 1Gbps/Full - flow control rx/tx <5>[ 5.577719] Sending DHCP requests . <3>[ 5.622429] hid-generic 0003:064F:2AF9.0001: device has no listeners, quitting <4>[ 7.733741] . <6>[ 8.510669] fsl_enetc 0000:00:00.0 eth0: Link is Up - 1Gbps/Full - flow control rx/tx <4>[ 11.501739] ., OK <6>[ 11.520007] IP-Config: Got DHCP answer from 172.16.0.254, my address is 172.16.0.117 <6>[ 11.528140] IP-Config: Complete: <6>[ 11.531680] device=eth0, hwaddr=00:a0:a5:5c:6c:72, ipaddr=172.16.0.117, mask=255.255.255.0, gw=172.16.0.254 <6>[ 11.542210] host=172.16.0.117, domain=lava.lan, nis-domain=(none) <6>[ 11.549057] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 11.549076] nameserver0=8.8.8.8 <6>[ 11.581018] fsl_enetc 0000:00:00.2 eth2: Link is Down <6>[ 11.607635] fsl_enetc 0000:00:00.6 eth3: Link is Down <6>[ 11.630906] clk: Disabling unused clocks <6>[ 11.635176] ALSA device list: <6>[ 11.638431] No soundcards found. <6>[ 11.643328] Freeing unused kernel memory: 2112K <6>[ 11.648348] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 11.711277] udevd[107]: starting version 3.2.9 <5>[ 12.793709] random: crng init done <27>[ 12.800267] udevd[107]: specified user 'tss' unknown <27>[ 12.805664] udevd[107]: specified group 'tss' unknown <30>[ 12.812128] udevd[108]: starting eudev-3.2.9 <6>[ 13.049942] EDAC MC0: Giving out device to module fsl_ddr_edac controller fsl_mc_err: DEV fsl_mc_err (INTERRUPT) <6>[ 13.068339] fsl_enetc 0000:00:00.6 enp0s0f6: renamed from eth3 <6>[ 13.089140] fsl_ddr_edac acquired irq 121 for MC <6>[ 13.100158] fsl_ddr_edac MC err registered <6>[ 13.105741] fsl_enetc 0000:00:00.1 enp0s0f1: renamed from eth1 <6>[ 13.120051] fsl_enetc 0000:00:00.2 enp0s0f2: renamed from eth2 <4>[ 13.130346] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 13.139819] NET: Registered PF_INET6 protocol family <4>[ 13.148925] rtc-rv8803 0-0032: Voltage low, temperature compensation stopped. <6>[ 13.156832] fsl_enetc 0000:00:00.0 enp0s0f0: renamed from eth0 (while UP) <4>[ 13.172045] rtc-rv8803 0-0032: Voltage low, data loss detected. <6>[ 13.179938] Segment Routing with IPv6 <6>[ 13.188108] In-situ OAM (IOAM) with IPv6 <6>[ 13.192568] at24 0-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 13.203305] rtc-rv8803 0-0032: Voltage low, data is invalid. <4>[ 13.214149] at24 1-0057: supply vcc not found, using dummy regulator <6>[ 13.222898] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. <6>[ 13.237369] rtc-rv8803 0-0032: registered as rtc0 <4>[ 13.243902] rtc-rv8803 0-0032: Voltage low, data is invalid. <6>[ 13.250104] at24 1-0057: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <3>[ 13.257406] rtc-rv8803 0-0032: hctosys: unable to read the hardware clock <4>[ 13.266470] at24 2-0050: supply vcc not found, using dummy regulator <6>[ 13.277609] sl28cpld-wdt 2000000.i2c:sl28cpld@4a:watchdog@4: initial timeout 6 sec <6>[ 13.286690] mscc_felix 0000:00:00.5: Adding to iommu group 14 <6>[ 13.293837] mscc_felix 0000:00:00.5: enabling device (0400 -> 0402) <6>[ 13.301967] at24 2-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <6>[ 13.311051] CAN device driver interface <3>[ 13.345866] leds-gpio leds: Failed to create device link (0x180) with 2000000.i2c:sl28cpld@4a:gpio@15 <6>[ 13.409101] ftm-alarm 2800000.timer: registered as rtc1 <6>[ 13.441443] caam 8000000.crypto: device ID = 0x0a12070000000000 (Era 10) <6>[ 13.459016] usbcore: registered new device driver onboard-usb-hub <6>[ 13.476624] caam 8000000.crypto: job rings = 4, qi = 0 <6>[ 13.482486] usb 1-1.6: USB disconnect, device number 3 <6>[ 13.488755] etnaviv etnaviv: bound f0c0000.gpu (ops gpu_ops [etnaviv]) <6>[ 13.496214] etnaviv-gpu f0c0000.gpu: model: GC7000, revision: 6202 <6>[ 13.503652] [drm] Initialized etnaviv 1.4.0 20151214 for etnaviv on minor 0 <6>[ 13.513655] mali-dp f080000.display: Adding to iommu group 15 <6>[ 13.641837] caam_jr 8010000.jr: Adding to iommu group 16 <6>[ 13.649327] caam algorithms registered in /proc/crypto <6>[ 13.654825] caam 8000000.crypto: registering rng-caam <6>[ 13.660329] caam 8000000.crypto: rng crypto API alg registered prng-caam <6>[ 13.667786] caam_jr 8020000.jr: Adding to iommu group 17 <6>[ 13.678188] caam_jr 8030000.jr: Adding to iommu group 18 <6>[ 13.686370] caam_jr 8040000.jr: Adding to iommu group 19 <6>[ 13.779136] hub 1-1:1.0: USB hub found <6>[ 13.783249] hub 1-1:1.0: 7 ports detected <6>[ 13.876695] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 0 <6>[ 13.883792] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 1 <6>[ 13.890885] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 2 <6>[ 13.897968] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 3 <6>[ 13.931735] mscc_felix 0000:00:00.5: configuring for fixed/internal link mode <6>[ 13.939245] mscc_felix 0000:00:00.5: Link is Up - 2.5Gbps/Full - flow control rx/tx <6>[ 13.939374] hub 1-1:1.0: USB hub found <6>[ 13.951338] hub 1-1:1.0: 7 ports detected <6>[ 13.957312] mscc_felix 0000:00:00.5: configuring for fixed/internal link mode <6>[ 13.964805] mscc_felix 0000:00:00.5: Link is Up - 1Gbps/Full - flow control rx/tx <6>[ 14.036400] mscc_felix 0000:00:00.5 swp0 (uninitialized): PHY [0000:00:00.3:07] driver [Broadcom BCM54140] (irq=POLL) <6>[ 14.112515] mscc_felix 0000:00:00.5 swp1 (uninitialized): PHY [0000:00:00.3:08] driver [Broadcom BCM54140] (irq=POLL) <6>[ 14.153201] mscc_felix 0000:00:00.5 swp2 (uninitialized): PHY [0000:00:00.3:09] driver [Broadcom BCM54140] (irq=POLL) <6>[ 14.229349] mscc_felix 0000:00:00.5 swp3 (uninitialized): PHY [0000:00:00.3:0a] driver [Broadcom BCM54140] (irq=POLL) <6>[ 14.242564] fsl_enetc 0000:00:00.2 enp0s0f2: entered promiscuous mode <6>[ 14.249803] fsl_enetc 0000:00:00.6 enp0s0f6: entered promiscuous mode <6>[ 14.256656] DSA: tree 0 setup done Saving random seed: OK Starting network: <6>[ 14.289749] usb 1-1.6: new full-speed USB device number 4 using xhci-hcd ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # <3>[ 14.454746] hid-generic 0003:064F:2AF9.0002: device has no listeners, quitting # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-494875/environment . /lava-494875/environment / # /lava-494875/bin/lava-test-runner /lava-494875/0 /lava-494875/bin/lava-test-runner /lava-494875/0 + export 'TESTRUN_ID=0_dmesg' + c<8>[ 14.874809] d /lava-494875/0/tests/0_dmesg + cat uuid + UUID=494875_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 14.896005] <8>[ 14.917921] <8>[ 14.940874] + set +x <8>[ 14.950625] / #