Trying 0.0.0.0... Connected to 0. Escape character is '^]'. U-Boot SPL 2021.10 (Oct 25 2021 - 13:39:59 +0200) Trying to boot from SPI U-Boot 2021.10 (Oct 25 2021 - 13:39:59 +0200) SoC: LS1028A Rev1.0 (0x870b0110) Clock Configuration: CPU0(A72):1300 MHz CPU1(A72):1300 MHz Bus: 400 MHz DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 34004010 00000030 00000000 00000000 00000010: 00000000 008f0000 0030c000 00000000 00000020: 06200000 00002580 00000000 00019016 00000030: 00000000 00000048 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000304 00000000 000e7000 00000000 00000070: bb580000 00020000 Model: Kontron SMARC-sAL28 (Dual PHY) EL: 3 DRAM: 4 GiB DDR 4 GiB (DDR3, 32-bit, CL=11, ECC on) SEC0: RNG instantiated CPU: 2 cores online Using SERDES1 Protocol: 47960 (0xbb58) MMC: FSL_SDHC: 1, FSL_SDHC: 0 Loading Environment from SPIFlash... SF: Detected w25q32dw with page size 256 Bytes, erase size 64 KiB, total 4 MiB OK PCIe1: pcie@3400000 Root Complex: no link PCIe2: pcie@3500000 Root Complex: no link In: serial@21c0500 Out: serial@21c0500 Err: serial@21c0500 Net: eth0: enetc-0, eth1: enetc-1 Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => dhcp dhcp enetc-0 Waiting for PHY auto negotiation to complete.... done BOOTP broadcast 1 BOOTP broadcast 2 DHCP client bound to address 172.16.0.117 (255 ms) => setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 => tftp 0x82000000 494864/tftp-deploy-c9iw37o6/kernel/Image tftp 0x82000000 494864/tftp-deploy-c9iw37o6/kernel/Image Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.117; sending through gateway 172.16.0.254 Filename '494864/tftp-deploy-c9iw37o6/kernel/Image'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############## 16.3 MiB/s done Bytes transferred = 42187264 (283ba00 hex) => tftp 0x90080000 494864/tftp-deploy-c9iw37o6/ramdisk/ramdisk.cpio.gz.uboot tftp 0x90080000 494864/tftp-deploy-c9iw37o6/ramdisk/ramdisk.cpio.gz.uboot Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.117; sending through gateway 172.16.0.254 Filename '494864/tftp-deploy-c9iw37o6/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x90080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############### 14.7 MiB/s done Bytes transferred = 24066204 (16f389c hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 494864/tftp-deploy-c9iw37o6/dtb/fsl-ls1028a-kontron-kbox-a-230-ls.dtb tftp 0x90000000 494864/tftp-deploy-c9iw37o6/dtb/fsl-ls1028a-kontron-kbox-a-230-ls.dtb Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.117; sending through gateway 172.16.0.254 Filename '494864/tftp-deploy-c9iw37o6/dtb/fsl-ls1028a-kontron-kbox-a-230-ls.dtb'. Load address: 0x90000000 Loading: *### 7 MiB/s done Bytes transferred = 29429 (72f5 hex) => setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => booti 0x82000000 0x90080000 0x90000000 booti 0x82000000 0x90080000 0x90000000 ## Loading init Ramdisk from Legacy Image at 90080000 ... Image Name: Created: 2024-09-06 17:01:47 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 24066140 Bytes = 23 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Using Device Tree in place at 0000000090000000, end 000000009000a2f4 WARNING could not find node fsl,ls1028a-gpu: FDT_ERR_NOTFOUND. Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [ 0.000000] Linux version 6.6.48 (KernelCI@build-j310416-arm64-gcc-12-defconfig-config-randomize-basewhhqp) (aarch64-linux-gnu-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP PREEMPT Fri Sep 6 16:41:15 UTC 2024 [ 0.000000] KASLR disabled due to lack of seed [ 0.000000] Machine model: Kontron KBox A-230-LS [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: ns16550a0 at MMIO 0x00000000021c0500 (options '115200n8') [ 0.000000] printk: bootconsole [ns16550a0] enabled [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x20ff7d2740-0x20ff7d5fff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000020ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] NoSplit zone start for each node [ 0.000000] NoMerge zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] node 0: [mem 0x0000002080000000-0x00000020ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] cma: Reserved 32 MiB at 0x00000000fcc00000 on node -1 [ 0.000000] percpu: Embedded 22 pages/cpu s52264 r8192 d29656 u90112 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: Spectre-v3a [ 0.000000] CPU features: detected: Spectre-v4 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: detected: ARM erratum 1742098 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <5>[ 0.000000] Unknown kernel command line parameters \"n8\", will be passed to user space. <6>[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] Fallback order for Node 0: 0 <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1032192 <6>[ 0.000000] Policy zone: Normal <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] software IO TLB: area num 2. <6>[ 0.000000] software IO TLB: mapped [mem 0x00000000f8c00000-0x00000000fcc00000] (64MB) <6>[ 0.000000] Memory: 3949532K/4194304K available (16704K kernel code, 4462K rwdata, 10660K rodata, 9216K init, 642K bss, 212004K reserved, 32768K cma-reserved) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=2. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode <6>[ 0.000000] GICv3: 256 SPIs implemented <6>[ 0.000000] GICv3: 0 Extended SPIs implemented <6>[ 0.000000] Root IRQ handler: gic_handle_irq <6>[ 0.000000] GICv3: GICv3 features: 16 PPIs <6>[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006040000 <6>[ 0.000000] ITS [mem 0x06020000-0x0603ffff] <6>[ 0.000000] ITS@0x0000000006020000: allocated 65536 Devices @2080080000 (flat, esz 8, psz 64K, shr 0) <6>[ 0.000000] ITS: using cache flushing for cmd queue <6>[ 0.000000] GICv3: using LPI property table @0x0000002080030000 <6>[ 0.000000] GIC: using cache flushing for LPI property table <6>[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000002080040000 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns <6>[ 0.000000] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns <6>[ 0.008833] Console: colour dummy device 80x25 <6>[ 0.013629] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) <6>[ 0.024350] pid_max: default: 32768 minimum: 301 <6>[ 0.029313] LSM: initializing lsm=capability,integrity <6>[ 0.034835] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.042582] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.051751] RCU Tasks: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1. <6>[ 0.059196] RCU Tasks Trace: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1. <6>[ 0.067238] rcu: Hierarchical SRCU implementation. <6>[ 0.072341] rcu: Max phase no-delay instances is 1000. <6>[ 0.078023] Platform MSI: msi-controller@6020000 domain created <6>[ 0.084354] PCI/MSI: /interrupt-controller@6000000/msi-controller@6020000 domain created <6>[ 0.092838] fsl-mc MSI: msi-controller@6020000 domain created <6>[ 0.099623] EFI services will not be available. <6>[ 0.104566] smp: Bringing up secondary CPUs ... <6>[ 0.109691] Detected PIPT I-cache on CPU1 <6>[ 0.109730] GICv3: CPU1: found redistributor 1 region 0:0x0000000006060000 <6>[ 0.109739] GICv3: CPU1: using allocated LPI pending table @0x0000002080050000 <6>[ 0.109765] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] <6>[ 0.109823] smp: Brought up 1 node, 2 CPUs <6>[ 0.140139] SMP: Total of 2 processors activated. <6>[ 0.145151] CPU features: detected: 32-bit EL0 Support <6>[ 0.150608] CPU features: detected: 32-bit EL1 Support <6>[ 0.156060] CPU features: detected: CRC32 instructions <6>[ 0.161558] CPU: All CPU(s) started at EL2 <6>[ 0.165971] alternatives: applying system-wide alternatives <6>[ 0.173098] devtmpfs: initialized <6>[ 0.180432] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.190555] futex hash table entries: 512 (order: 3, 32768 bytes, linear) <6>[ 0.198233] pinctrl core: initialized pinctrl subsystem <6>[ 0.204261] Machine: Kontron KBox A-230-LS <6>[ 0.208660] SoC family: QorIQ LS1028A <6>[ 0.212613] SoC ID: svr:0x870b0110, Revision: 1.0 <6>[ 0.217871] DMI not present or invalid. <6>[ 0.222470] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.229231] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.236731] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.244850] audit: initializing netlink subsys (disabled) <5>[ 0.250659] audit: type=2000 audit(0.152:1): state=initialized audit_enabled=0 res=1 <6>[ 0.251332] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.258751] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.265113] cpuidle: using governor menu <6>[ 0.276313] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.283460] ASID allocator initialised with 65536 entries <6>[ 0.290324] Serial: AMBA PL011 UART driver <6>[ 0.305359] Modules: 22288 pages in range for non-PLT usage <6>[ 0.305366] Modules: 513808 pages in range for PLT usage <6>[ 0.311704] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.324448] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page <6>[ 0.331038] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.338153] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page <6>[ 0.344743] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.351857] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page <6>[ 0.358447] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.365561] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page <6>[ 0.373236] ACPI: Interpreter disabled. <6>[ 0.378801] iommu: Default domain type: Translated <6>[ 0.383898] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.390556] SCSI subsystem initialized <6>[ 0.394817] usbcore: registered new interface driver usbfs <6>[ 0.400643] usbcore: registered new interface driver hub <6>[ 0.406287] usbcore: registered new device driver usb <6>[ 0.411966] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.419804] i2c i2c-0: IMX I2C adapter registered <6>[ 0.425023] imx-i2c 2030000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.432691] i2c i2c-1: IMX I2C adapter registered <6>[ 0.437812] imx-i2c 2040000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.445470] i2c i2c-2: IMX I2C adapter registered <6>[ 0.450853] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.456133] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.465635] PTP clock support registered <6>[ 0.469959] EDAC MC: Ver: 3.0.0 <6>[ 0.473757] scmi_core: SCMI protocol bus registered <6>[ 0.479379] FPGA manager framework <6>[ 0.483131] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.490125] vgaarb: loaded <6>[ 0.493351] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.499911] VFS: Disk quotas dquot_6.6.0 <6>[ 0.504153] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 0.511463] pnp: PnP ACPI: disabled <6>[ 0.519482] NET: Registered PF_INET protocol family <6>[ 0.524845] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 0.534609] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear) <6>[ 0.543544] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.551638] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) <6>[ 0.559982] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes, linear) <6>[ 0.568339] TCP: Hash tables configured (established 32768 bind 32768) <6>[ 0.575303] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.582374] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.589955] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.596233] RPC: Registered named UNIX socket transport module. <6>[ 0.602484] RPC: Registered udp transport module. <6>[ 0.607495] RPC: Registered tcp transport module. <6>[ 0.612506] RPC: Registered tcp-with-tls transport module. <6>[ 0.618306] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.625078] PCI: CLS 0 bytes, default 64 <6>[ 0.629443] Unpacking initramfs... <6>[ 0.633412] kvm [1]: IPA Size Limit: 44 bits <6>[ 0.639141] kvm [1]: GICv3: no GICV resource entry <6>[ 0.644346] kvm [1]: disabling GICv2 emulation <6>[ 0.649119] kvm [1]: GIC system register CPU interface enabled <6>[ 0.655315] kvm [1]: vgic interrupt IRQ9 <6>[ 0.659570] kvm [1]: Hyp mode initialized successfully <5>[ 0.665803] Initialise system trusted keyrings <6>[ 0.670700] workingset: timestamp_bits=42 max_order=20 bucket_order=0 <6>[ 0.677694] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.684041] NFS: Registering the id_resolver key type <5>[ 0.689457] Key type id_resolver registered <5>[ 0.693947] Key type id_legacy registered <6>[ 0.698281] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.705321] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 0.713204] 9p: Installing v9fs 9p2000 file system support <6>[ 0.734276] jitterentropy: Initialization failed with host not compliant with requirements: 9 <5>[ 0.743160] Key type asymmetric registered <5>[ 0.747560] Asymmetric key parser 'x509' registered <6>[ 0.752805] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 0.760544] io scheduler mq-deadline registered <6>[ 0.765381] io scheduler kyber registered <6>[ 0.769735] io scheduler bfq registered <6>[ 0.780624] pci-host-generic 1f0000000.pcie: host bridge /soc/pcie@1f0000000 ranges: <6>[ 0.788769] pci-host-generic 1f0000000.pcie: MEM 0x01f8000000..0x01f815ffff -> 0x01f8000000 <6>[ 0.797935] pci-host-generic 1f0000000.pcie: MEM 0x01f8160000..0x01f81cffff -> 0x01f8160000 <6>[ 0.807096] pci-host-generic 1f0000000.pcie: MEM 0x01f81d0000..0x01f81effff -> 0x01f81d0000 <6>[ 0.816257] pci-host-generic 1f0000000.pcie: MEM 0x01f81f0000..0x01f820ffff -> 0x01f81f0000 <6>[ 0.825407] pci-host-generic 1f0000000.pcie: MEM 0x01f8210000..0x01f822ffff -> 0x01f8210000 <6>[ 0.834556] pci-host-generic 1f0000000.pcie: MEM 0x01f8230000..0x01f824ffff -> 0x01f8230000 <6>[ 0.843709] pci-host-generic 1f0000000.pcie: MEM 0x01fc000000..0x01fc3fffff -> 0x01fc000000 <6>[ 0.852906] pci-host-generic 1f0000000.pcie: ECAM at [mem 0x1f0000000-0x1f00fffff] for [bus 00] <6>[ 0.862157] pci-host-generic 1f0000000.pcie: PCI host bridge to bus 0000:00 <6>[ 0.869461] pci_bus 0000:00: root bus resource [bus 00] <6>[ 0.875013] pci_bus 0000:00: root bus resource [mem 0x1f8000000-0x1f815ffff] <6>[ 0.882402] pci_bus 0000:00: root bus resource [mem 0x1f8160000-0x1f81cffff pref] <6>[ 0.890225] pci_bus 0000:00: root bus resource [mem 0x1f81d0000-0x1f81effff] <6>[ 0.897609] pci_bus 0000:00: root bus resource [mem 0x1f81f0000-0x1f820ffff pref] <6>[ 0.905440] pci_bus 0000:00: root bus resource [mem 0x1f8210000-0x1f822ffff] <6>[ 0.912827] pci_bus 0000:00: root bus resource [mem 0x1f8230000-0x1f824ffff pref] <6>[ 0.920650] pci_bus 0000:00: root bus resource [mem 0x1fc000000-0x1fc3fffff] <6>[ 0.928054] pci 0000:00:00.0: [1957:e100] type 00 class 0x020001 <6>[ 0.934417] pci 0000:00:00.0: BAR 0: [mem 0x1f8000000-0x1f803ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 0.945228] pci 0000:00:00.0: BAR 2: [mem 0x1f8160000-0x1f816ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 0.956474] pci 0000:00:00.0: VF BAR 0: [mem 0x1f81d0000-0x1f81dffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 0.967551] pci 0000:00:00.0: VF BAR 2: [mem 0x1f81f0000-0x1f81fffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 0.979077] pci 0000:00:00.0: PME# supported from D0 D3hot <6>[ 0.984899] pci 0000:00:00.0: VF(n) BAR0 space: [mem 0x1f81d0000-0x1f81effff 64bit] (contains BAR0 for 2 VFs) <6>[ 0.995189] pci 0000:00:00.0: VF(n) BAR2 space: [mem 0x1f81f0000-0x1f820ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 1.006135] pci 0000:00:00.1: [1957:e100] type 00 class 0x020001 <6>[ 1.012512] pci 0000:00:00.1: BAR 0: [mem 0x1f8040000-0x1f807ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.023326] pci 0000:00:00.1: BAR 2: [mem 0x1f8170000-0x1f817ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.034581] pci 0000:00:00.1: VF BAR 0: [mem 0x1f8210000-0x1f821ffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 1.045654] pci 0000:00:00.1: VF BAR 2: [mem 0x1f8230000-0x1f823ffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 1.057181] pci 0000:00:00.1: PME# supported from D0 D3hot <6>[ 1.062993] pci 0000:00:00.1: VF(n) BAR0 space: [mem 0x1f8210000-0x1f822ffff 64bit] (contains BAR0 for 2 VFs) <6>[ 1.073273] pci 0000:00:00.1: VF(n) BAR2 space: [mem 0x1f8230000-0x1f824ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 1.084181] pci 0000:00:00.2: [1957:e100] type 00 class 0x020001 <6>[ 1.090541] pci 0000:00:00.2: BAR 0: [mem 0x1f8080000-0x1f80bffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.101362] pci 0000:00:00.2: BAR 2: [mem 0x1f8180000-0x1f818ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.112626] pci 0000:00:00.2: PME# supported from D0 D3hot <6>[ 1.118611] pci 0000:00:00.3: [1957:ee01] type 00 class 0x088001 <6>[ 1.124997] pci 0000:00:00.3: BAR 0: [mem 0x1f8100000-0x1f811ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.135812] pci 0000:00:00.3: BAR 2: [mem 0x1f8190000-0x1f819ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.147072] pci 0000:00:00.3: PME# supported from D0 D3hot <6>[ 1.153068] pci 0000:00:00.4: [1957:ee02] type 00 class 0x088001 <6>[ 1.159427] pci 0000:00:00.4: BAR 0: [mem 0x1f8120000-0x1f813ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.170244] pci 0000:00:00.4: BAR 2: [mem 0x1f81a0000-0x1f81affff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.181504] pci 0000:00:00.4: PME# supported from D0 D3hot <6>[ 1.187529] pci 0000:00:00.5: [1957:eef0] type 00 class 0x020801 <6>[ 1.193890] pci 0000:00:00.5: BAR 0: [mem 0x1f8140000-0x1f815ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.204702] pci 0000:00:00.5: BAR 2: [mem 0x1f81b0000-0x1f81bffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.215949] pci 0000:00:00.5: BAR 4: [mem 0x1fc000000-0x1fc3fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.226770] pci 0000:00:00.5: PME# supported from D0 D3hot <6>[ 1.232773] pci 0000:00:00.6: [1957:e100] type 00 class 0x020001 <6>[ 1.239152] pci 0000:00:00.6: BAR 0: [mem 0x1f80c0000-0x1f80fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.249965] pci 0000:00:00.6: BAR 2: [mem 0x1f81c0000-0x1f81cffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.261226] pci 0000:00:00.6: PME# supported from D0 D3hot <6>[ 1.267894] pci 0000:00:1f.0: [1957:e001] type 00 class 0x080700 <6>[ 1.274280] OF: /soc/pcie@1f0000000: no msi-map translation for id 0xf8 on (null) <6>[ 1.282324] OF: /soc/pcie@1f0000000: no iommu-map translation for id 0xf8 on (null) <6>[ 1.290495] pcieport 0000:00:1f.0: PME: Signaling with IRQ 19 <6>[ 1.297389] pcieport 0000:00:1f.0: AER: enabled with IRQ 19 <6>[ 1.303991] layerscape-pcie 3400000.pcie: host bridge /soc/pcie@3400000 ranges: <6>[ 1.311690] layerscape-pcie 3400000.pcie: IO 0x8000010000..0x800001ffff -> 0x0000000000 <6>[ 1.320606] layerscape-pcie 3400000.pcie: MEM 0x8040000000..0x807fffffff -> 0x0040000000 <6>[ 1.329575] layerscape-pcie 3400000.pcie: iATU: unroll F, 8 ob, 6 ib, align 4K, limit 4G <6>[ 1.466434] Freeing initrd memory: 23496K <6>[ 2.329438] layerscape-pcie 3400000.pcie: Phy link never came up <6>[ 2.335916] layerscape-pcie 3400000.pcie: PCI host bridge to bus 0001:00 <6>[ 2.342952] pci_bus 0001:00: root bus resource [bus 00-ff] <6>[ 2.348756] pci_bus 0001:00: root bus resource [io 0x0000-0xffff] <6>[ 2.355262] pci_bus 0001:00: root bus resource [mem 0x8040000000-0x807fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 2.366175] pci 0001:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 2.372564] pci 0001:00:00.0: supports D1 D2 <6>[ 2.377139] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 2.384380] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 2.391336] pci 0001:00:00.0: PCI bridge to [bus 01] <6>[ 2.396759] layerscape-pcie 3500000.pcie: host bridge /soc/pcie@3500000 ranges: <6>[ 2.404439] layerscape-pcie 3500000.pcie: IO 0x8800010000..0x880001ffff -> 0x0000000000 <6>[ 2.413323] layerscape-pcie 3500000.pcie: MEM 0x8840000000..0x887fffffff -> 0x0040000000 <6>[ 2.422239] layerscape-pcie 3500000.pcie: iATU: unroll F, 8 ob, 6 ib, align 4K, limit 4G <6>[ 3.430778] layerscape-pcie 3500000.pcie: Phy link never came up <6>[ 3.437169] layerscape-pcie 3500000.pcie: PCI host bridge to bus 0002:00 <6>[ 3.444203] pci_bus 0002:00: root bus resource [bus 00-ff] <6>[ 3.450007] pci_bus 0002:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) <6>[ 3.459321] pci_bus 0002:00: root bus resource [mem 0x8840000000-0x887fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 3.470227] pci 0002:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 3.476609] pci 0002:00:00.0: supports D1 D2 <6>[ 3.481182] pci 0002:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 3.488325] pci_bus 0002:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 3.495280] pci 0002:00:00.0: PCI bridge to [bus 01] <6>[ 3.501391] EINJ: ACPI disabled. <6>[ 3.521002] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 3.529572] printk: console [ttyS0] disabled <6>[ 3.534341] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 20, base_baud = 12500000) is a 16550A <6>[ 3.543506] printk: console [ttyS0] enabled <6>[ 3.543506] printk: console [ttyS0] enabled <6>[ 3.552469] printk: bootconsole [ns16550a0] disabled <6>[ 3.552469] printk: bootconsole [ns16550a0] disabled <6>[ 3.565902] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 20, base_baud = 12500000) is a 16550A <6>[ 3.575361] SuperH (H)SCI(F) driver initialized <6>[ 3.580469] msm_serial: driver initialized <6>[ 3.585388] 2270000.serial: ttyLP2 at MMIO 0x2270000 (irq = 21, base_baud = 12500000) is a FSL_LPUART <6>[ 3.595271] STM32 USART driver initialized <5>[ 3.602668] arm-smmu 5000000.iommu: probing hardware configuration... <5>[ 3.609403] arm-smmu 5000000.iommu: SMMUv2 with: <5>[ 3.614299] arm-smmu 5000000.iommu: stage 1 translation <5>[ 3.619892] arm-smmu 5000000.iommu: stage 2 translation <5>[ 3.625484] arm-smmu 5000000.iommu: nested translation <5>[ 3.630989] arm-smmu 5000000.iommu: coherent table walk <5>[ 3.636581] arm-smmu 5000000.iommu: (IDR0.CTTW overridden by FW configuration) <5>[ 3.644180] arm-smmu 5000000.iommu: stream matching with 128 register groups <5>[ 3.651607] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) <5>[ 3.658427] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 <5>[ 3.665154] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA <5>[ 3.671880] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA <5>[ 3.678837] arm-smmu 5000000.iommu: preserved 0 boot mappings <4>[ 3.685008] arm-smmu 5000000.iommu: Failed to disable prefetcher [errata #841119 and #826419], check ACR.CACHE_LOCK <6>[ 3.699075] loop: module loaded <6>[ 3.709933] megasas: 07.725.01.00-rc1 <6>[ 3.714662] ahci-qoriq 3200000.sata: Adding to iommu group 0 <4>[ 3.720708] ahci-qoriq 3200000.sata: supply ahci not found, using dummy regulator <4>[ 3.728567] ahci-qoriq 3200000.sata: supply phy not found, using dummy regulator <4>[ 3.736296] ahci-qoriq 3200000.sata: supply target not found, using dummy regulator <6>[ 3.744366] ahci-qoriq 3200000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode <6>[ 3.753633] ahci-qoriq 3200000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst <6>[ 3.764033] scsi host0: ahci-qoriq <6>[ 3.767843] ata1: SATA max UDMA/133 mmio [mem 0x03200000-0x0320ffff] port 0x100 irq 95 <6>[ 3.778421] spi-nor spi0.0: w25q32dw (4096 Kbytes) <6>[ 4.087557] ata1: SATA link down (SStatus 0 SControl 300) <5>[ 4.107037] 5 fixed-partitions partitions found on MTD device 20c0000.spi <5>[ 4.114129] Creating 5 MTD partitions on \"20c0000.spi\": <5>[ 4.119638] 0x000000000000-0x000000010000 : \"rcw\" <5>[ 4.125518] 0x000000010000-0x0000001e0000 : \"failsafe bootloader\" <5>[ 4.132564] 0x000000200000-0x000000210000 : \"configuration store\" <5>[ 4.139532] 0x000000210000-0x0000003e0000 : \"bootloader\" <5>[ 4.145758] 0x0000003e0000-0x000000400000 : \"bootloader environment\" <6>[ 4.155869] tun: Universal TUN/TAP device driver, 1.6 <6>[ 4.161863] thunder_xcv, ver 1.0 <6>[ 4.165393] thunder_bgx, ver 1.0 <6>[ 4.168905] nicpf, ver 1.0 <6>[ 4.172454] fsl_enetc 0000:00:00.0: Adding to iommu group 1 <6>[ 4.178539] fsl_enetc 0000:00:00.1: Adding to iommu group 2 <6>[ 4.184566] fsl_enetc 0000:00:00.2: Adding to iommu group 3 <6>[ 4.190576] fsl_enetc 0000:00:00.6: Adding to iommu group 4 <6>[ 4.196800] fsl_enetc_mdio 0000:00:00.3: Adding to iommu group 5 <6>[ 4.309363] fsl_enetc_mdio 0000:00:00.3: enabling device (0400 -> 0402) <6>[ 4.346982] mdio_bus 0000:00:00.3:04: Fixed dependency cycle(s) with /soc/pcie@1f0000000/mdio@0,3/ethernet-phy@4/vddio-regulator <6>[ 4.426847] fsl_enetc_ptp 0000:00:00.4: Adding to iommu group 6 <6>[ 4.433149] fsl_enetc_ptp 0000:00:00.4: enabling device (0404 -> 0406) <4>[ 4.440092] ptp_qoriq: device tree node missing required elements, try automatic configuration <6>[ 4.449127] pps pps0: new PPS source ptp0 <6>[ 4.453940] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 4.461462] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 4.467092] hclge is initializing <6>[ 4.470693] e1000: Intel(R) PRO/1000 Network Driver <6>[ 4.475850] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 4.481905] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 4.487152] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 4.493379] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 4.499060] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 4.504931] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 4.511482] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 4.517907] sky2: driver version 1.30 <6>[ 4.522701] VFIO - User Level meta-driver version: 0.3 <6>[ 4.528440] dwc3 3100000.usb: Adding to iommu group 7 <6>[ 4.534692] dwc3 3110000.usb: Adding to iommu group 8 <6>[ 4.542233] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 4.548022] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 <6>[ 4.556091] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000808002000010 <6>[ 4.565811] xhci-hcd xhci-hcd.0.auto: irq 100, io mem 0x03110000 <6>[ 4.572191] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 4.577964] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 <6>[ 4.585916] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed <6>[ 4.593100] hub 1-0:1.0: USB hub found <6>[ 4.597147] hub 1-0:1.0: 1 port detected <6>[ 4.601539] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 4.610194] hub 2-0:1.0: USB hub found <6>[ 4.614235] hub 2-0:1.0: 1 port detected <6>[ 4.618933] usbcore: registered new interface driver usb-storage <6>[ 4.627210] i2c_dev: i2c /dev entries driver <6>[ 4.635044] sp805-wdt c000000.watchdog: registration successful <6>[ 4.641420] sp805-wdt c010000.watchdog: registration successful <6>[ 4.649615] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver <6>[ 4.658476] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.664955] sdhci: Copyright(c) Pierre Ossman <6>[ 4.670077] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.676986] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.683513] sdhci-esdhc 2140000.mmc: Adding to iommu group 9 <6>[ 4.689624] sdhci-esdhc 2150000.mmc: Adding to iommu group 10 <6>[ 4.695679] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.703767] usbcore: registered new interface driver usbhid <6>[ 4.709646] usbhid: USB HID core driver <6>[ 4.715888] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available <6>[ 4.721415] mmc1: SDHCI controller on 2140000.mmc [2140000.mmc] using ADMA <6>[ 4.724444] mmc0: SDHCI controller on 2150000.mmc [2150000.mmc] using ADMA <6>[ 4.742723] NET: Registered PF_PACKET protocol family <6>[ 4.748145] 9pnet: Installing 9P2000 support <5>[ 4.752751] Key type dns_resolver registered <6>[ 4.763563] registered taskstats version 1 <5>[ 4.768028] Loading compiled-in X.509 certificates <6>[ 4.781168] fsl-edma 22c0000.dma-controller: Adding to iommu group 11 <6>[ 4.789131] pcieport 0001:00:00.0: Adding to iommu group 12 <6>[ 4.795188] pcieport 0001:00:00.0: PME: Signaling with IRQ 105 <6>[ 4.801493] pcieport 0001:00:00.0: AER: enabled with IRQ 105 <6>[ 4.807660] pcieport 0002:00:00.0: Adding to iommu group 13 <6>[ 4.813680] pcieport 0002:00:00.0: PME: Signaling with IRQ 106 <6>[ 4.820010] pcieport 0002:00:00.0: AER: enabled with IRQ 106 <6>[ 4.862005] mmc0: new HS400 MMC card at address 0001 <6>[ 4.867272] usb 1-1: new high-speed USB device number 2 using xhci-hcd <6>[ 4.874530] mmcblk0: mmc0:0001 S0J58X 29.6 GiB <6>[ 4.880553] mmcblk0: p1 p2 p3 <6>[ 4.884394] mmcblk0boot0: mmc0:0001 S0J58X 31.5 MiB <6>[ 4.890556] mmcblk0boot1: mmc0:0001 S0J58X 31.5 MiB <6>[ 4.896625] mmcblk0rpmb: mmc0:0001 S0J58X 4.00 MiB, chardev (234:0) <6>[ 4.933376] fsl_enetc 0000:00:00.0: enabling device (0400 -> 0402) <6>[ 4.940836] fsl_enetc 0000:00:00.0: no MAC address specified for SI1, using 86:5d:cd:30:a9:d6 <6>[ 4.949670] fsl_enetc 0000:00:00.0: no MAC address specified for SI2, using 76:d2:0d:2b:52:61 <6>[ 5.065447] fsl_enetc 0000:00:00.1: enabling device (0400 -> 0402) <6>[ 5.072922] fsl_enetc 0000:00:00.1: no MAC address specified for SI1, using ba:4a:22:41:61:23 <6>[ 5.073120] hub 1-1:1.0: USB hub found <6>[ 5.081797] fsl_enetc 0000:00:00.1: no MAC address specified for SI2, using ba:fe:01:77:0e:3e <6>[ 5.094831] hub 1-1:1.0: 7 ports detected <6>[ 5.189428] fsl_enetc 0000:00:00.2: enabling device (0400 -> 0402) <6>[ 5.305425] fsl_enetc 0000:00:00.6: enabling device (0400 -> 0402) <6>[ 5.318720] input: buttons0 as /devices/platform/buttons0/input/input0 <6>[ 5.379262] fsl_enetc 0000:00:00.0 eth0: PHY [0000:00:00.3:05] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL) <6>[ 5.391027] fsl_enetc 0000:00:00.0 eth0: configuring for inband/sgmii link mode <6>[ 5.425462] usb 1-1.6: new full-speed USB device number 3 using xhci-hcd <6>[ 5.483691] fsl_enetc 0000:00:00.1 eth1: PHY [0000:00:00.3:04] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL) <6>[ 5.495444] fsl_enetc 0000:00:00.1 eth1: configuring for phy/rgmii-id link mode <6>[ 5.533421] fsl_enetc 0000:00:00.2 eth2: configuring for fixed/internal link mode <6>[ 5.541286] fsl_enetc 0000:00:00.2 eth2: Link is Up - 2.5Gbps/Full - flow control rx/tx <6>[ 5.556844] fsl_enetc 0000:00:00.6 eth3: configuring for fixed/internal link mode <6>[ 5.564726] fsl_enetc 0000:00:00.6 eth3: Link is Up - 1Gbps/Full - flow control rx/tx <3>[ 5.586288] hid-generic 0003:064F:2AF9.0001: device has no listeners, quitting <5>[ 5.593373] Sending DHCP requests .. <6>[ 8.478359] fsl_enetc 0000:00:00.0 eth0: Link is Up - 1Gbps/Full - flow control rx/tx <4>[ 11.265392] ., OK <6>[ 11.287663] IP-Config: Got DHCP answer from 172.16.0.254, my address is 172.16.0.117 <6>[ 11.295799] IP-Config: Complete: <6>[ 11.299334] device=eth0, hwaddr=00:a0:a5:5c:6c:72, ipaddr=172.16.0.117, mask=255.255.255.0, gw=172.16.0.254 <6>[ 11.309862] host=172.16.0.117, domain=lava.lan, nis-domain=(none) <6>[ 11.316709] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 11.316727] nameserver0=8.8.8.8 <6>[ 11.348229] fsl_enetc 0000:00:00.2 eth2: Link is Down <6>[ 11.374696] fsl_enetc 0000:00:00.6 eth3: Link is Down <6>[ 11.392726] clk: Disabling unused clocks <6>[ 11.397006] ALSA device list: <6>[ 11.400269] No soundcards found. <6>[ 11.409012] Freeing unused kernel memory: 9216K <6>[ 11.414100] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 11.478046] udevd[108]: starting version 3.2.9 <5>[ 12.577361] random: crng init done <27>[ 12.583896] udevd[108]: specified user 'tss' unknown <27>[ 12.589292] udevd[108]: specified group 'tss' unknown <30>[ 12.595674] udevd[109]: starting eudev-3.2.9 <6>[ 12.843624] fsl_enetc 0000:00:00.1 enp0s0f1: renamed from eth1 <6>[ 12.863976] fsl_enetc 0000:00:00.2 enp0s0f2: renamed from eth2 <6>[ 12.877442] EDAC MC0: Giving out device to module fsl_ddr_edac controller fsl_mc_err: DEV fsl_mc_err (INTERRUPT) <4>[ 12.888609] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 12.895617] fsl_enetc 0000:00:00.0 enp0s0f0: renamed from eth0 (while UP) <6>[ 12.908923] NET: Registered PF_INET6 protocol family <6>[ 12.913691] fsl_ddr_edac acquired irq 121 for MC <6>[ 12.919233] fsl_enetc 0000:00:00.6 enp0s0f6: renamed from eth3 <4>[ 12.929400] rtc-rv8803 0-0032: Voltage low, temperature compensation stopped. <6>[ 12.941687] fsl_ddr_edac MC err registered <6>[ 12.941803] at24 0-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 12.946183] rtc-rv8803 0-0032: Voltage low, data loss detected. <4>[ 12.954250] at24 1-0057: supply vcc not found, using dummy regulator <6>[ 12.966723] Segment Routing with IPv6 <6>[ 12.981411] In-situ OAM (IOAM) with IPv6 <6>[ 12.984037] at24 1-0057: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <6>[ 12.996155] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. <4>[ 13.004702] rtc-rv8803 0-0032: Voltage low, data is invalid. <4>[ 13.016098] at24 2-0050: supply vcc not found, using dummy regulator <6>[ 13.027025] mscc_felix 0000:00:00.5: Adding to iommu group 14 <6>[ 13.033377] mscc_felix 0000:00:00.5: enabling device (0400 -> 0402) <6>[ 13.033846] rtc-rv8803 0-0032: registered as rtc0 <6>[ 13.048472] at24 2-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 13.049611] rtc-rv8803 0-0032: Voltage low, data is invalid. <6>[ 13.071901] sl28cpld-wdt 2000000.i2c:sl28cpld@4a:watchdog@4: initial timeout 6 sec <3>[ 13.085942] rtc-rv8803 0-0032: hctosys: unable to read the hardware clock <6>[ 13.116301] CAN device driver interface <3>[ 13.121515] leds-gpio leds: Failed to create device link (0x180) with 2000000.i2c:sl28cpld@4a:gpio@15 <6>[ 13.195657] ftm-alarm 2800000.timer: registered as rtc1 <6>[ 13.213305] usbcore: registered new device driver onboard-usb-hub <6>[ 13.228518] usb 1-1.6: USB disconnect, device number 3 <6>[ 13.261439] etnaviv etnaviv: bound f0c0000.gpu (ops gpu_ops [etnaviv]) <6>[ 13.268555] etnaviv-gpu f0c0000.gpu: model: GC7000, revision: 6202 <6>[ 13.285019] caam 8000000.crypto: device ID = 0x0a12070000000000 (Era 10) <6>[ 13.286604] [drm] Initialized etnaviv 1.4.0 20151214 for etnaviv on minor 0 <6>[ 13.297361] caam 8000000.crypto: job rings = 4, qi = 0 <6>[ 13.309055] mali-dp f080000.display: Adding to iommu group 15 <6>[ 13.442801] caam_jr 8010000.jr: Adding to iommu group 16 <6>[ 13.453597] caam algorithms registered in /proc/crypto <6>[ 13.459141] caam 8000000.crypto: registering rng-caam <6>[ 13.464726] caam 8000000.crypto: rng crypto API alg registered prng-caam <6>[ 13.472190] caam_jr 8020000.jr: Adding to iommu group 17 <6>[ 13.481993] caam_jr 8030000.jr: Adding to iommu group 18 <6>[ 13.493899] caam_jr 8040000.jr: Adding to iommu group 19 <6>[ 13.552923] hub 1-1:1.0: USB hub found <6>[ 13.557150] hub 1-1:1.0: 7 ports detected <6>[ 13.626680] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 0 <6>[ 13.633780] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 1 <6>[ 13.640883] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 2 <6>[ 13.647970] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 3 <6>[ 13.681462] mscc_felix 0000:00:00.5: configuring for fixed/internal link mode <6>[ 13.688958] mscc_felix 0000:00:00.5: Link is Up - 2.5Gbps/Full - flow control rx/tx <6>[ 13.698991] mscc_felix 0000:00:00.5: configuring for fixed/internal link mode <6>[ 13.706477] mscc_felix 0000:00:00.5: Link is Up - 1Gbps/Full - flow control rx/tx <6>[ 13.712933] hub 1-1:1.0: USB hub found <6>[ 13.718357] hub 1-1:1.0: 7 ports detected <6>[ 13.752201] mscc_felix 0000:00:00.5 swp0 (uninitialized): PHY [0000:00:00.3:07] driver [Broadcom BCM54140] (irq=POLL) <6>[ 13.828422] mscc_felix 0000:00:00.5 swp1 (uninitialized): PHY [0000:00:00.3:08] driver [Broadcom BCM54140] (irq=POLL) <6>[ 13.896789] mscc_felix 0000:00:00.5 swp2 (uninitialized): PHY [0000:00:00.3:09] driver [Broadcom BCM54140] (irq=POLL) <6>[ 13.972787] mscc_felix 0000:00:00.5 swp3 (uninitialized): PHY [0000:00:00.3:0a] driver [Broadcom BCM54140] (irq=POLL) <6>[ 13.985273] fsl_enetc 0000:00:00.2 enp0s0f2: entered promiscuous mode <6>[ 13.992584] fsl_enetc 0000:00:00.6 enp0s0f6: entered promiscuous mode <6>[ 13.999441] DSA: tree 0 setup done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # <6>[ 14.073374] usb 1-1.6: new full- speed USB device number 4 using xhci-hcd / # # #<3>[ 14.228438] hid-generic 0003:064F:2AF9.0002: device has no listeners, quitting / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-494864/environment . /lava-494864/environment / # /lava-494864/bin/lava-test-runner /lava-494864/0 /lava-494864/bin/lava-test-runner /lava-494864/0 + export 'TESTRUN_ID=0_dmesg' + c<8>[ 14.633316] d /lava-494864/0/tests/0_dmesg + cat uuid + UUID=494864_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 14.654794] <8>[ 14.676331] <8>[ 14.698336] + set +x <8>[ 14.708201] / # <6>�