Trying 0.0.0.0... Connected to 0. Escape character is '^]'. U-Boot SPL 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) Initializing DDR....using raw memory timing SPI boot Trying to boot from SPI U-Boot 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) SoC: LS1028A Rev1.0 (0x870b0110) Clock Configuration: CPU0(A72):1300 MHz CPU1(A72):1300 MHz Bus: 400 MHz DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 34004010 00000030 00000000 00000000 00000010: 00000000 008f0000 0030c000 00000000 00000020: 06200000 00002580 00000000 00019016 00000030: 00000000 00000048 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000103 00000000 100e7026 00000000 00000070: bb580000 00020000 Model: Kontron SMARC-sAL28 Board Hardware Variant: Single PHY (3) RCW: sl28-3-11_q.bin DRAM: Detected UDIMM Fixed DDR on board 3.9 GiB DDR 3.9 GiB (DDR3, 32-bit, CL=11, ECC on) Using SERDES1 Protocol: 47960 (0xbb58) PCIe1: pcie@3400000 Root Complex: no link PCIe2: pcie@3500000 Root Complex: no link CPLD: v18 WDT: Started with servicing (60s timeout) Waking secondary cores to start from fbd3c000 All (2) cores are up. MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPI Flash... SF: Detected w25q32jw with page size 256 Bytes, erase size 64 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial VPD: Using device 0x50 on I2C Bus 2 Net: eth0: enetc-0, eth2: enetc-2 Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => dhcp dhcp enetc-0 Waiting for PHY auto negotiation to complete.... done BOOTP broadcast 1 BOOTP broadcast 2 DHCP client bound to address 172.16.0.106 (254 ms) => setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 => tftp 0x82000000 491760/tftp-deploy-i8400qp6/kernel/Image tftp 0x82000000 491760/tftp-deploy-i8400qp6/kernel/Image Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.106; sending through gateway 172.16.0.254 Filename '491760/tftp-deploy-i8400qp6/kernel/Image'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################### 15.6 MiB/s done Bytes transferred = 42252800 (284ba00 hex) => tftp 0x90080000 491760/tftp-deploy-i8400qp6/ramdisk/ramdisk.cpio.gz.uboot tftp 0x90080000 491760/tftp-deploy-i8400qp6/ramdisk/ramdisk.cpio.gz.uboot Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.106; sending through gateway 172.16.0.254 Filename '491760/tftp-deploy-i8400qp6/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x90080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############## 17.3 MiB/s done Bytes transferred = 24058374 (16f1a06 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 491760/tftp-deploy-i8400qp6/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb tftp 0x90000000 491760/tftp-deploy-i8400qp6/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.106; sending through gateway 172.16.0.254 Filename '491760/tftp-deploy-i8400qp6/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb'. Load address: 0x90000000 Loading: *### 3.5 MiB/s done Bytes transferred = 29445 (7305 hex) => setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => booti 0x82000000 0x90080000 0x90000000 booti 0x82000000 0x90080000 0x90000000 ## Loading init Ramdisk from Legacy Image at 90080000 ... Image Name: Created: 2024-08-30 9:06:12 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 24058310 Bytes = 22.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Using Device Tree in place at 0000000090000000, end 000000009000a304 WARNING could not find node fsl,ls1028a-gpu: FDT_ERR_NOTFOUND. Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [ 0.000000] Linux version 6.6.46 (KernelCI@build-j301746-arm64-gcc-12-defconfig-config-randomize-base9pnmn) (aarch64-linux-gnu-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP PREEMPT Fri Aug 30 08:46:19 UTC 2024 [ 0.000000] KASLR disabled due to lack of seed [ 0.000000] Machine model: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: ns16550a0 at MMIO 0x00000000021c0500 (options '115200n8') [ 0.000000] printk: bootconsole [ns16550a0] enabled [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x20ff7f3740-0x20ff7f6fff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000020ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] NoSplit zone start for each node [ 0.000000] NoMerge zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fbdfffff] [ 0.000000] node 0: [mem 0x0000002080000000-0x00000020ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] On node 0, zone Normal: 16896 pages in unavailable ranges [ 0.000000] cma: Reserved 32 MiB at 0x00000000f9c00000 on node -1 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv0.2 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] percpu: Embedded 22 pages/cpu s52264 r8192 d29656 u90112 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: Spectre-v3a [ 0.000000] CPU features: detected: Spectre-v4 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: detected: ARM erratum 1742098 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <5>[ 0.000000] Unknown kernel command line parameters \"n8\", will be passed to user space. <6>[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] Fallback order for Node 0: 0 <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1015296 <6>[ 0.000000] Policy zone: Normal <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] software IO TLB: area num 2. <6>[ 0.000000] software IO TLB: mapped [mem 0x00000000f5c00000-0x00000000f9c00000] (64MB) <6>[ 0.000000] Memory: 3882012K/4126720K available (16768K kernel code, 4462K rwdata, 10660K rodata, 9216K init, 642K bss, 211940K reserved, 32768K cma-reserved) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=2. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode <6>[ 0.000000] GICv3: 256 SPIs implemented <6>[ 0.000000] GICv3: 0 Extended SPIs implemented <6>[ 0.000000] Root IRQ handler: gic_handle_irq <6>[ 0.000000] GICv3: GICv3 features: 16 PPIs <6>[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006040000 <6>[ 0.000000] ITS [mem 0x06020000-0x0603ffff] <6>[ 0.000000] ITS@0x0000000006020000: allocated 65536 Devices @2080080000 (flat, esz 8, psz 64K, shr 0) <6>[ 0.000000] ITS: using cache flushing for cmd queue <6>[ 0.000000] GICv3: using LPI property table @0x0000002080030000 <6>[ 0.000000] GIC: using cache flushing for LPI property table <6>[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000002080040000 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns <6>[ 0.000000] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns <6>[ 0.008853] Console: colour dummy device 80x25 <6>[ 0.013651] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) <6>[ 0.024371] pid_max: default: 32768 minimum: 301 <6>[ 0.029334] LSM: initializing lsm=capability,integrity <6>[ 0.034855] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.042603] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.051760] RCU Tasks: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1. <6>[ 0.059204] RCU Tasks Trace: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1. <6>[ 0.067244] rcu: Hierarchical SRCU implementation. <6>[ 0.072346] rcu: Max phase no-delay instances is 1000. <6>[ 0.078027] Platform MSI: msi-controller@6020000 domain created <6>[ 0.084353] PCI/MSI: /interrupt-controller@6000000/msi-controller@6020000 domain created <6>[ 0.092838] fsl-mc MSI: msi-controller@6020000 domain created <6>[ 0.099672] EFI services will not be available. <6>[ 0.104613] smp: Bringing up secondary CPUs ... <6>[ 0.109738] Detected PIPT I-cache on CPU1 <6>[ 0.109777] GICv3: CPU1: found redistributor 1 region 0:0x0000000006060000 <6>[ 0.109786] GICv3: CPU1: using allocated LPI pending table @0x0000002080050000 <6>[ 0.109811] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] <6>[ 0.109872] smp: Brought up 1 node, 2 CPUs <6>[ 0.140186] SMP: Total of 2 processors activated. <6>[ 0.145198] CPU features: detected: 32-bit EL0 Support <6>[ 0.150655] CPU features: detected: 32-bit EL1 Support <6>[ 0.156107] CPU features: detected: CRC32 instructions <6>[ 0.161603] CPU: All CPU(s) started at EL2 <6>[ 0.166018] alternatives: applying system-wide alternatives <6>[ 0.173136] devtmpfs: initialized <6>[ 0.180348] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.190469] futex hash table entries: 512 (order: 3, 32768 bytes, linear) <6>[ 0.198146] pinctrl core: initialized pinctrl subsystem <6>[ 0.204172] Machine: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier <6>[ 0.211818] SoC family: QorIQ LS1028A <6>[ 0.215771] SoC ID: svr:0x870b0110, Revision: 1.0 <6>[ 0.221022] DMI not present or invalid. <6>[ 0.225811] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.232562] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.240070] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.248184] audit: initializing netlink subsys (disabled) <5>[ 0.253991] audit: type=2000 audit(0.152:1): state=initialized audit_enabled=0 res=1 <6>[ 0.254660] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.262082] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.268444] cpuidle: using governor menu <6>[ 0.279643] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.286790] ASID allocator initialised with 65536 entries <6>[ 0.293653] Serial: AMBA PL011 UART driver <6>[ 0.309386] Modules: 22272 pages in range for non-PLT usage <6>[ 0.309394] Modules: 513792 pages in range for PLT usage <6>[ 0.315713] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.328466] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page <6>[ 0.335056] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.342172] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page <6>[ 0.348762] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.355877] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page <6>[ 0.362466] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.369581] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page <6>[ 0.377229] ACPI: Interpreter disabled. <6>[ 0.382906] iommu: Default domain type: Translated <6>[ 0.388015] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.394658] SCSI subsystem initialized <6>[ 0.398909] usbcore: registered new interface driver usbfs <6>[ 0.404733] usbcore: registered new interface driver hub <6>[ 0.410377] usbcore: registered new device driver usb <6>[ 0.416065] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.423900] i2c i2c-0: IMX I2C adapter registered <6>[ 0.429163] imx-i2c 2030000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.436829] i2c i2c-1: IMX I2C adapter registered <6>[ 0.441953] imx-i2c 2040000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.449689] i2c i2c-2: IMX I2C adapter registered <6>[ 0.455158] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.460438] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.469941] PTP clock support registered <6>[ 0.474262] EDAC MC: Ver: 3.0.0 <6>[ 0.478152] scmi_core: SCMI protocol bus registered <6>[ 0.483807] FPGA manager framework <6>[ 0.487567] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.494557] vgaarb: loaded <6>[ 0.497784] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.504342] VFS: Disk quotas dquot_6.6.0 <6>[ 0.508585] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 0.515895] pnp: PnP ACPI: disabled <6>[ 0.523836] NET: Registered PF_INET protocol family <6>[ 0.529201] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 0.538966] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear) <6>[ 0.547894] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.555988] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) <6>[ 0.564330] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes, linear) <6>[ 0.572688] TCP: Hash tables configured (established 32768 bind 32768) <6>[ 0.579647] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.586717] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.594299] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.600581] RPC: Registered named UNIX socket transport module. <6>[ 0.606829] RPC: Registered udp transport module. <6>[ 0.611840] RPC: Registered tcp transport module. <6>[ 0.616849] RPC: Registered tcp-with-tls transport module. <6>[ 0.622655] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.629428] PCI: CLS 0 bytes, default 64 <6>[ 0.633821] kvm [1]: IPA Size Limit: 44 bits <6>[ 0.633926] Unpacking initramfs... <6>[ 0.642098] kvm [1]: GICv3: no GICV resource entry <6>[ 0.642103] kvm [1]: disabling GICv2 emulation <6>[ 0.647200] kvm [1]: GIC system register CPU interface enabled <6>[ 0.647216] kvm [1]: vgic interrupt IRQ9 <6>[ 0.662347] kvm [1]: Hyp mode initialized successfully <5>[ 0.670244] Initialise system trusted keyrings <6>[ 0.675141] workingset: timestamp_bits=42 max_order=20 bucket_order=0 <6>[ 0.682142] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.688500] NFS: Registering the id_resolver key type <5>[ 0.693889] Key type id_resolver registered <5>[ 0.698378] Key type id_legacy registered <6>[ 0.702704] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.709738] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 0.717596] 9p: Installing v9fs 9p2000 file system support <5>[ 0.742411] Key type asymmetric registered <5>[ 0.746820] Asymmetric key parser 'x509' registered <6>[ 0.752063] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 0.759822] io scheduler mq-deadline registered <6>[ 0.764670] io scheduler kyber registered <6>[ 0.769026] io scheduler bfq registered <6>[ 0.780555] pci-host-generic 1f0000000.pcie: host bridge /soc/pcie@1f0000000 ranges: <6>[ 0.788717] pci-host-generic 1f0000000.pcie: MEM 0x01f8000000..0x01f815ffff -> 0x01f8000000 <6>[ 0.797900] pci-host-generic 1f0000000.pcie: MEM 0x01f8160000..0x01f81cffff -> 0x01f8160000 <6>[ 0.807071] pci-host-generic 1f0000000.pcie: MEM 0x01f81d0000..0x01f81effff -> 0x01f81d0000 <6>[ 0.816243] pci-host-generic 1f0000000.pcie: MEM 0x01f81f0000..0x01f820ffff -> 0x01f81f0000 <6>[ 0.825411] pci-host-generic 1f0000000.pcie: MEM 0x01f8210000..0x01f822ffff -> 0x01f8210000 <6>[ 0.834581] pci-host-generic 1f0000000.pcie: MEM 0x01f8230000..0x01f824ffff -> 0x01f8230000 <6>[ 0.843745] pci-host-generic 1f0000000.pcie: MEM 0x01fc000000..0x01fc3fffff -> 0x01fc000000 <6>[ 0.852971] pci-host-generic 1f0000000.pcie: ECAM at [mem 0x1f0000000-0x1f00fffff] for [bus 00] <6>[ 0.862245] pci-host-generic 1f0000000.pcie: PCI host bridge to bus 0000:00 <6>[ 0.869552] pci_bus 0000:00: root bus resource [bus 00] <6>[ 0.875111] pci_bus 0000:00: root bus resource [mem 0x1f8000000-0x1f815ffff] <6>[ 0.882511] pci_bus 0000:00: root bus resource [mem 0x1f8160000-0x1f81cffff pref] <6>[ 0.890350] pci_bus 0000:00: root bus resource [mem 0x1f81d0000-0x1f81effff] <6>[ 0.897758] pci_bus 0000:00: root bus resource [mem 0x1f81f0000-0x1f820ffff pref] <6>[ 0.905597] pci_bus 0000:00: root bus resource [mem 0x1f8210000-0x1f822ffff] <6>[ 0.913003] pci_bus 0000:00: root bus resource [mem 0x1f8230000-0x1f824ffff pref] <6>[ 0.920845] pci_bus 0000:00: root bus resource [mem 0x1fc000000-0x1fc3fffff] <6>[ 0.928266] pci 0000:00:00.0: [1957:e100] type 00 class 0x020001 <6>[ 0.934644] pci 0000:00:00.0: BAR 0: [mem 0x1f8000000-0x1f803ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 0.945473] pci 0000:00:00.0: BAR 2: [mem 0x1f8160000-0x1f816ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 0.956741] pci 0000:00:00.0: VF BAR 0: [mem 0x1f81d0000-0x1f81dffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 0.967826] pci 0000:00:00.0: VF BAR 2: [mem 0x1f81f0000-0x1f81fffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 0.979379] pci 0000:00:00.0: PME# supported from D0 D3hot <6>[ 0.985194] pci 0000:00:00.0: VF(n) BAR0 space: [mem 0x1f81d0000-0x1f81effff 64bit] (contains BAR0 for 2 VFs) <6>[ 0.995486] pci 0000:00:00.0: VF(n) BAR2 space: [mem 0x1f81f0000-0x1f820ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 1.006434] pci 0000:00:00.1: [1957:e100] type 00 class 0x020001 <6>[ 1.012798] pci 0000:00:00.1: BAR 0: [mem 0x1f8040000-0x1f807ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.023630] pci 0000:00:00.1: BAR 2: [mem 0x1f8170000-0x1f817ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.034894] pci 0000:00:00.1: VF BAR 0: [mem 0x1f8210000-0x1f821ffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 1.045987] pci 0000:00:00.1: VF BAR 2: [mem 0x1f8230000-0x1f823ffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 1.057533] pci 0000:00:00.1: PME# supported from D0 D3hot <6>[ 1.063366] pci 0000:00:00.1: VF(n) BAR0 space: [mem 0x1f8210000-0x1f822ffff 64bit] (contains BAR0 for 2 VFs) <6>[ 1.073664] pci 0000:00:00.1: VF(n) BAR2 space: [mem 0x1f8230000-0x1f824ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 1.084599] pci 0000:00:00.2: [1957:e100] type 00 class 0x020001 <6>[ 1.090978] pci 0000:00:00.2: BAR 0: [mem 0x1f8080000-0x1f80bffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.101803] pci 0000:00:00.2: BAR 2: [mem 0x1f8180000-0x1f818ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.113086] pci 0000:00:00.2: PME# supported from D0 D3hot <6>[ 1.119084] pci 0000:00:00.3: [1957:ee01] type 00 class 0x088001 <6>[ 1.125450] pci 0000:00:00.3: BAR 0: [mem 0x1f8100000-0x1f811ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.136260] pci 0000:00:00.3: BAR 2: [mem 0x1f8190000-0x1f819ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.147518] pci 0000:00:00.3: PME# supported from D0 D3hot <6>[ 1.153490] pci 0000:00:00.4: [1957:ee02] type 00 class 0x088001 <6>[ 1.159852] pci 0000:00:00.4: BAR 0: [mem 0x1f8120000-0x1f813ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.170670] pci 0000:00:00.4: BAR 2: [mem 0x1f81a0000-0x1f81affff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.181929] pci 0000:00:00.4: PME# supported from D0 D3hot <6>[ 1.187942] pci 0000:00:00.5: [1957:eef0] type 00 class 0x020801 <6>[ 1.194305] pci 0000:00:00.5: BAR 0: [mem 0x1f8140000-0x1f815ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.205116] pci 0000:00:00.5: BAR 2: [mem 0x1f81b0000-0x1f81bffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.216362] pci 0000:00:00.5: BAR 4: [mem 0x1fc000000-0x1fc3fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.227185] pci 0000:00:00.5: PME# supported from D0 D3hot <6>[ 1.233245] pci 0000:00:00.6: [1957:e100] type 00 class 0x020001 <6>[ 1.239629] pci 0000:00:00.6: BAR 0: [mem 0x1f80c0000-0x1f80fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.250454] pci 0000:00:00.6: BAR 2: [mem 0x1f81c0000-0x1f81cffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.261735] pci 0000:00:00.6: PME# supported from D0 D3hot <6>[ 1.268474] pci 0000:00:1f.0: [1957:e001] type 00 class 0x080700 <6>[ 1.274883] OF: /soc/pcie@1f0000000: no msi-map translation for id 0xf8 on (null) <6>[ 1.389811] pci 0000:00:00.1: enabling device (0400 -> 0402) <6>[ 1.396614] pci 0000:00:00.1: enetc_fixup_clear_rss_rfs+0x0/0x5c took 111049 usecs <6>[ 1.489005] Freeing initrd memory: 23488K <6>[ 1.509797] pci 0000:00:00.2: enabling device (0400 -> 0402) <6>[ 1.516107] pci 0000:00:00.2: enetc_fixup_clear_rss_rfs+0x0/0x5c took 108924 usecs <6>[ 1.629794] pci 0000:00:00.6: enabling device (0400 -> 0402) <6>[ 1.636064] pci 0000:00:00.6: enetc_fixup_clear_rss_rfs+0x0/0x5c took 109375 usecs <6>[ 1.644010] OF: /soc/pcie@1f0000000: no iommu-map translation for id 0xf8 on (null) <6>[ 1.652178] pcieport 0000:00:1f.0: PME: Signaling with IRQ 19 <6>[ 1.658455] pcieport 0000:00:1f.0: AER: enabled with IRQ 19 <6>[ 1.665103] layerscape-pcie 3400000.pcie: host bridge /soc/pcie@3400000 ranges: <6>[ 1.672791] layerscape-pcie 3400000.pcie: IO 0x8000010000..0x800001ffff -> 0x0000000000 <6>[ 1.681687] layerscape-pcie 3400000.pcie: MEM 0x8040000000..0x807fffffff -> 0x0040000000 <6>[ 1.690615] layerscape-pcie 3400000.pcie: iATU: unroll F, 8 ob, 6 ib, align 4K, limit 4G <6>[ 2.699154] layerscape-pcie 3400000.pcie: Phy link never came up <6>[ 2.705554] layerscape-pcie 3400000.pcie: PCI host bridge to bus 0001:00 <6>[ 2.712588] pci_bus 0001:00: root bus resource [bus 00-ff] <6>[ 2.718391] pci_bus 0001:00: root bus resource [io 0x0000-0xffff] <6>[ 2.724896] pci_bus 0001:00: root bus resource [mem 0x8040000000-0x807fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 2.735806] pci 0001:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 2.742191] pci 0001:00:00.0: supports D1 D2 <6>[ 2.746766] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 2.754029] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 2.760981] pci 0001:00:00.0: PCI bridge to [bus 01] <6>[ 2.766380] layerscape-pcie 3500000.pcie: host bridge /soc/pcie@3500000 ranges: <6>[ 2.774052] layerscape-pcie 3500000.pcie: IO 0x8800010000..0x880001ffff -> 0x0000000000 <6>[ 2.782936] layerscape-pcie 3500000.pcie: MEM 0x8840000000..0x887fffffff -> 0x0040000000 <6>[ 2.791847] layerscape-pcie 3500000.pcie: iATU: unroll F, 8 ob, 6 ib, align 4K, limit 4G <6>[ 3.800381] layerscape-pcie 3500000.pcie: Phy link never came up <6>[ 3.806771] layerscape-pcie 3500000.pcie: PCI host bridge to bus 0002:00 <6>[ 3.813805] pci_bus 0002:00: root bus resource [bus 00-ff] <6>[ 3.819608] pci_bus 0002:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) <6>[ 3.828921] pci_bus 0002:00: root bus resource [mem 0x8840000000-0x887fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 3.839826] pci 0002:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 3.846209] pci 0002:00:00.0: supports D1 D2 <6>[ 3.850783] pci 0002:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 3.858000] pci_bus 0002:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 3.864950] pci 0002:00:00.0: PCI bridge to [bus 01] <6>[ 3.871062] EINJ: ACPI disabled. <6>[ 3.891720] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 3.900283] printk: console [ttyS0] disabled <6>[ 3.905060] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 20, base_baud = 12500000) is a 16550A <6>[ 3.914224] printk: console [ttyS0] enabled <6>[ 3.914224] printk: console [ttyS0] enabled <6>[ 3.923169] printk: bootconsole [ns16550a0] disabled <6>[ 3.923169] printk: bootconsole [ns16550a0] disabled <6>[ 3.938350] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 20, base_baud = 12500000) is a 16550A <6>[ 3.947814] SuperH (H)SCI(F) driver initialized <6>[ 3.952946] msm_serial: driver initialized <6>[ 3.957892] 2270000.serial: ttyLP2 at MMIO 0x2270000 (irq = 21, base_baud = 12500000) is a FSL_LPUART <6>[ 3.967799] STM32 USART driver initialized <5>[ 3.975238] arm-smmu 5000000.iommu: probing hardware configuration... <5>[ 3.981972] arm-smmu 5000000.iommu: SMMUv2 with: <5>[ 3.986868] arm-smmu 5000000.iommu: stage 1 translation <5>[ 3.992460] arm-smmu 5000000.iommu: stage 2 translation <5>[ 3.998073] arm-smmu 5000000.iommu: nested translation <5>[ 4.003584] arm-smmu 5000000.iommu: coherent table walk <5>[ 4.009182] arm-smmu 5000000.iommu: (IDR0.CTTW overridden by FW configuration) <5>[ 4.016787] arm-smmu 5000000.iommu: stream matching with 128 register groups <5>[ 4.024214] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) <5>[ 4.031035] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 <5>[ 4.037762] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA <5>[ 4.044488] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA <5>[ 4.051435] arm-smmu 5000000.iommu: preserved 0 boot mappings <4>[ 4.057606] arm-smmu 5000000.iommu: Failed to disable prefetcher [errata #841119 and #826419], check ACR.CACHE_LOCK <6>[ 4.071675] loop: module loaded <6>[ 4.082680] megasas: 07.725.01.00-rc1 <6>[ 4.088850] spi-nor spi1.0: w25q128fw (16384 Kbytes) <6>[ 4.110162] spi-nor spi0.0: w25q32jwm (4096 Kbytes) <5>[ 4.144752] 5 fixed-partitions partitions found on MTD device 20c0000.spi <5>[ 4.151873] Creating 5 MTD partitions on \"20c0000.spi\": <5>[ 4.157383] 0x000000000000-0x000000010000 : \"rcw\" <5>[ 4.163194] 0x000000010000-0x0000001e0000 : \"failsafe bootloader\" <5>[ 4.170208] 0x000000200000-0x000000210000 : \"configuration store\" <5>[ 4.177215] 0x000000210000-0x0000003e0000 : \"bootloader\" <5>[ 4.183425] 0x0000003e0000-0x000000400000 : \"bootloader environment\" <6>[ 4.193490] tun: Universal TUN/TAP device driver, 1.6 <6>[ 4.199510] thunder_xcv, ver 1.0 <6>[ 4.203036] thunder_bgx, ver 1.0 <6>[ 4.206553] nicpf, ver 1.0 <6>[ 4.210128] fsl_enetc 0000:00:00.0: Adding to iommu group 0 <6>[ 4.216401] fsl_enetc_mdio 0000:00:00.3: Adding to iommu group 1 <6>[ 4.329796] fsl_enetc_mdio 0000:00:00.3: enabling device (0400 -> 0402) <6>[ 4.354123] fsl_enetc_ptp 0000:00:00.4: Adding to iommu group 2 <6>[ 4.360425] fsl_enetc_ptp 0000:00:00.4: enabling device (0404 -> 0406) <4>[ 4.367372] ptp_qoriq: device tree node missing required elements, try automatic configuration <6>[ 4.376398] pps pps0: new PPS source ptp0 <6>[ 4.381213] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 4.388738] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 4.394366] hclge is initializing <6>[ 4.397968] e1000: Intel(R) PRO/1000 Network Driver <6>[ 4.403126] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 4.409177] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 4.414420] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 4.420644] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 4.426323] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 4.432194] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 4.438749] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 4.445186] sky2: driver version 1.30 <6>[ 4.450035] VFIO - User Level meta-driver version: 0.3 <6>[ 4.455785] dwc3 3100000.usb: Adding to iommu group 3 <6>[ 4.462022] dwc3 3110000.usb: Adding to iommu group 4 <6>[ 4.469635] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 4.475427] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 <6>[ 4.483496] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000808002000010 <6>[ 4.493201] xhci-hcd xhci-hcd.0.auto: irq 98, io mem 0x03100000 <6>[ 4.499497] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 4.505269] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 <6>[ 4.513220] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed <6>[ 4.520430] hub 1-0:1.0: USB hub found <6>[ 4.524474] hub 1-0:1.0: 1 port detected <6>[ 4.528859] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 4.537515] hub 2-0:1.0: USB hub found <6>[ 4.541557] hub 2-0:1.0: 1 port detected <6>[ 4.546066] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 4.551856] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 <6>[ 4.559932] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000808002000010 <6>[ 4.569667] xhci-hcd xhci-hcd.1.auto: irq 99, io mem 0x03110000 <6>[ 4.575957] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 4.581730] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 <6>[ 4.589682] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed <6>[ 4.596809] hub 3-0:1.0: USB hub found <6>[ 4.600852] hub 3-0:1.0: 1 port detected <6>[ 4.605226] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 4.613888] hub 4-0:1.0: USB hub found <6>[ 4.617924] hub 4-0:1.0: 1 port detected <6>[ 4.622671] usbcore: registered new interface driver usb-storage <6>[ 4.631073] i2c_dev: i2c /dev entries driver <6>[ 4.639116] sp805-wdt c000000.watchdog: registration successful <6>[ 4.645476] sp805-wdt c010000.watchdog: registration successful <6>[ 4.653827] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver <6>[ 4.662692] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.669177] sdhci: Copyright(c) Pierre Ossman <6>[ 4.674352] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.681310] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.687869] sdhci-esdhc 2150000.mmc: Adding to iommu group 5 <6>[ 4.693847] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.694107] sdhci-esdhc 2140000.mmc: Adding to iommu group 6 <6>[ 4.708326] usbcore: registered new interface driver usbhid <6>[ 4.714270] usbhid: USB HID core driver <6>[ 4.720667] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available <6>[ 4.729861] mmc1: SDHCI controller on 2140000.mmc [2140000.mmc] using ADMA <6>[ 4.730319] mmc0: SDHCI controller on 2150000.mmc [2150000.mmc] using ADMA <6>[ 4.740341] NET: Registered PF_PACKET protocol family <6>[ 4.749676] 9pnet: Installing 9P2000 support <5>[ 4.754270] Key type dns_resolver registered <6>[ 4.765017] registered taskstats version 1 <5>[ 4.769470] Loading compiled-in X.509 certificates <6>[ 4.782275] fsl-edma 22c0000.dma-controller: Adding to iommu group 7 <6>[ 4.790141] pcieport 0001:00:00.0: Adding to iommu group 8 <6>[ 4.796084] pcieport 0001:00:00.0: PME: Signaling with IRQ 104 <6>[ 4.802422] pcieport 0001:00:00.0: AER: enabled with IRQ 104 <6>[ 4.808556] pcieport 0002:00:00.0: Adding to iommu group 9 <6>[ 4.814560] pcieport 0002:00:00.0: PME: Signaling with IRQ 105 <6>[ 4.820848] pcieport 0002:00:00.0: AER: enabled with IRQ 105 <6>[ 4.854618] mmc0: new HS400 MMC card at address 0001 <6>[ 4.860287] mmcblk0: mmc0:0001 S0J56X 7.34 GiB <6>[ 4.865031] usb 3-1: new high-speed USB device number 2 using xhci-hcd <6>[ 4.873209] mmcblk0: p1 p2 <6>[ 4.876742] mmcblk0boot0: mmc0:0001 S0J56X 31.5 MiB <6>[ 4.882903] mmcblk0boot1: mmc0:0001 S0J56X 31.5 MiB <6>[ 4.888936] mmcblk0rpmb: mmc0:0001 S0J56X 4.00 MiB, chardev (234:0) <6>[ 4.933803] fsl_enetc 0000:00:00.0: enabling device (0400 -> 0402) <6>[ 4.941235] fsl_enetc 0000:00:00.0: no MAC address specified for SI1, using 9e:40:50:02:1d:2c <6>[ 4.950093] fsl_enetc 0000:00:00.0: no MAC address specified for SI2, using 26:e7:b4:76:09:8d <6>[ 4.962422] input: buttons0 as /devices/platform/buttons0/input/input0 <6>[ 5.003387] fsl_enetc 0000:00:00.0 eth0: PHY [0000:00:00.3:05] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL) <6>[ 5.014998] fsl_enetc 0000:00:00.0 eth0: configuring for inband/sgmii link mode <6>[ 5.076972] hub 3-1:1.0: USB hub found <6>[ 5.081202] hub 3-1:1.0: 7 ports detected <6>[ 8.094821] fsl_enetc 0000:00:00.0 eth0: Link is Up - 1Gbps/Full - flow control rx/tx <5>[ 8.117837] Sending DHCP requests ., OK <6>[ 8.138063] IP-Config: Got DHCP answer from 172.16.0.254, my address is 172.16.0.106 <6>[ 8.146161] IP-Config: Complete: <6>[ 8.149672] device=eth0, hwaddr=00:e0:4b:6e:9b:2b, ipaddr=172.16.0.106, mask=255.255.255.0, gw=172.16.0.254 <6>[ 8.160200] host=172.16.0.106, domain=lava.lan, nis-domain=(none) <6>[ 8.167049] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 8.167067] nameserver0=8.8.8.8 <6>[ 8.177924] clk: Disabling unused clocks <6>[ 8.182255] ALSA device list: <6>[ 8.185499] No soundcards found. <6>[ 8.193928] Freeing unused kernel memory: 9216K <6>[ 8.198971] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 8.266784] udevd[103]: starting version 3.2.9 <5>[ 9.373792] random: crng init done <27>[ 9.380401] udevd[103]: specified user 'tss' unknown <27>[ 9.385815] udevd[103]: specified group 'tss' unknown <30>[ 9.392231] udevd[104]: starting eudev-3.2.9 <6>[ 9.637460] EDAC MC0: Giving out device to module fsl_ddr_edac controller fsl_mc_err: DEV fsl_mc_err (INTERRUPT) <6>[ 9.640957] fsl_enetc 0000:00:00.0 enp0s0f0: renamed from eth0 (while UP) <6>[ 9.648071] fsl_ddr_edac acquired irq 111 for MC <6>[ 9.670490] NET: Registered PF_INET6 protocol family <6>[ 9.675779] fsl_ddr_edac MC err registered <6>[ 9.687040] Segment Routing with IPv6 <6>[ 9.691474] In-situ OAM (IOAM) with IPv6 <4>[ 9.697528] rtc-rv8803 0-0032: Voltage low, temperature compensation stopped. <6>[ 9.737692] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. <4>[ 9.765869] rtc-rv8803 0-0032: Voltage low, data loss detected. <4>[ 9.775491] wm8904 2-001a: supply DCVDD not found, using dummy regulator <4>[ 9.783103] at24 0-0050: supply vcc not found, using dummy regulator <4>[ 9.790266] wm8904 2-001a: supply DBVDD not found, using dummy regulator <6>[ 9.801286] at24 0-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 9.810747] rtc-rv8803 0-0032: Voltage low, data is invalid. <4>[ 9.817712] wm8904 2-001a: supply AVDD not found, using dummy regulator <4>[ 9.826089] at24 1-0057: supply vcc not found, using dummy regulator <6>[ 9.832820] rtc-rv8803 0-0032: registered as rtc0 <6>[ 9.833293] sl28cpld-wdt 2000000.i2c:sl28cpld@4a:watchdog@4: initial timeout 6 sec <4>[ 9.838158] wm8904 2-001a: supply CPVDD not found, using dummy regulator <6>[ 9.846766] at24 1-0057: 8192 byte 24c64 EEPROM, writable, 32 bytes/write <4>[ 9.852745] wm8904 2-001a: supply MICVDD not found, using dummy regulator <4>[ 9.867290] at24 2-0050: supply vcc not found, using dummy regulator <4>[ 9.874502] rtc-rv8803 0-0032: Voltage low, data is invalid. <6>[ 9.879136] wm8904 2-001a: revision A <3>[ 9.880473] rtc-rv8803 0-0032: hctosys: unable to read the hardware clock <6>[ 9.894016] CAN device driver interface <6>[ 9.898637] at24 2-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <6>[ 9.947672] caam 8000000.crypto: Entropy delay = 3200 <6>[ 9.969461] caam 8000000.crypto: Instantiated RNG4 SH0 <6>[ 9.975236] ftm-alarm 2800000.timer: registered as rtc1 <6>[ 9.981602] caam 8000000.crypto: Instantiated RNG4 SH1 <6>[ 9.989852] caam 8000000.crypto: device ID = 0x0a12070000000000 (Era 10) <6>[ 9.997088] caam 8000000.crypto: job rings = 4, qi = 0 <6>[ 10.012901] usbcore: registered new device driver onboard-usb-hub <6>[ 10.081111] mali-dp f080000.display: Adding to iommu group 10 <6>[ 10.093519] etnaviv etnaviv: bound f0c0000.gpu (ops gpu_ops [etnaviv]) <6>[ 10.143810] etnaviv-gpu f0c0000.gpu: model: GC7000, revision: 6202 <6>[ 10.151455] caam_jr 8010000.jr: Adding to iommu group 11 <6>[ 10.156677] [drm] Initialized etnaviv 1.4.0 20151214 for etnaviv on minor 0 <6>[ 10.161859] caam algorithms registered in /proc/crypto <6>[ 10.169853] caam 8000000.crypto: registering rng-caam <6>[ 10.175331] caam 8000000.crypto: rng crypto API alg registered prng-caam <6>[ 10.182542] caam_jr 8020000.jr: Adding to iommu group 12 <6>[ 10.190106] caam_jr 8030000.jr: Adding to iommu group 13 <6>[ 10.196264] caam_jr 8040000.jr: Adding to iommu group 14 <6>[ 10.389020] hub 3-1:1.0: USB hub found <6>[ 10.393300] hub 3-1:1.0: 7 ports detected done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # <6>[ 10.548817] hub 3-1:1.0: USB hub found <6>[ 10.553022] hub 3-1:1.0: 7 ports detected / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-491760/environment . /lava-491760/environment / # /lava-491760/bin/lava-test-runner /lava-491760/0 /lava-491760/bin/lava-test-runner /lava-491760/0 + export 'TESTRUN_ID=0_dmesg' + c<8>[ 11.050213] d /lava-491760/0/tests/0_dmesg + cat uuid + UUID=491760_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 11.071596] <8>[ 11.093089] <8>[ 11.116267] + set +x <8>[ 11.125709] / #