Trying 0.0.0.0... Connected to 0. Escape character is '^]'. U-Boot SPL 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) Initializing DDR....using raw memory timing SPI boot Trying to boot from SPI U-Boot 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) SoC: LS1028A Rev1.0 (0x870b0110) Clock Configuration: CPU0(A72):1300 MHz CPU1(A72):1300 MHz Bus: 400 MHz DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 34004010 00000030 00000000 00000000 00000010: 00000000 008f0000 0030c000 00000000 00000020: 06200000 00002580 00000000 00019016 00000030: 00000000 00000048 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000103 00000000 100e7026 00000000 00000070: bb580000 00020000 Model: Kontron SMARC-sAL28 Board Hardware Variant: Single PHY (3) RCW: sl28-3-11_q.bin DRAM: Detected UDIMM Fixed DDR on board 3.9 GiB DDR 3.9 GiB (DDR3, 32-bit, CL=11, ECC on) Using SERDES1 Protocol: 47960 (0xbb58) PCIe1: pcie@3400000 Root Complex: no link PCIe2: pcie@3500000 Root Complex: no link CPLD: v18 WDT: Started with servicing (60s timeout) Waking secondary cores to start from fbd3c000 All (2) cores are up. MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPI Flash... SF: Detected w25q32jw with page size 256 Bytes, erase size 64 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial VPD: Using device 0x50 on I2C Bus 2 Net: eth0: enetc-0, eth2: enetc-2 Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => dhcp dhcp enetc-0 Waiting for PHY auto negotiation to complete...... done BOOTP broadcast 1 BOOTP broadcast 2 DHCP client bound to address 172.16.0.106 (256 ms) => setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 => tftp 0x82000000 491750/tftp-deploy-7tzao22j/kernel/Image tftp 0x82000000 491750/tftp-deploy-7tzao22j/kernel/Image Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.106; sending through gateway 172.16.0.254 Filename '491750/tftp-deploy-7tzao22j/kernel/Image'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################### 17.1 MiB/s done Bytes transferred = 42252800 (284ba00 hex) => tftp 0x90080000 491750/tftp-deploy-7tzao22j/ramdisk/ramdisk.cpio.gz.uboot tftp 0x90080000 491750/tftp-deploy-7tzao22j/ramdisk/ramdisk.cpio.gz.uboot Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.106; sending through gateway 172.16.0.254 Filename '491750/tftp-deploy-7tzao22j/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x90080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############### 5.7 MiB/s done Bytes transferred = 24061668 (16f26e4 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 491750/tftp-deploy-7tzao22j/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb tftp 0x90000000 491750/tftp-deploy-7tzao22j/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.106; sending through gateway 172.16.0.254 Filename '491750/tftp-deploy-7tzao22j/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb'. Load address: 0x90000000 Loading: *### 4.7 MiB/s done Bytes transferred = 29445 (7305 hex) => setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => booti 0x82000000 0x90080000 0x90000000 booti 0x82000000 0x90080000 0x90000000 ## Loading init Ramdisk from Legacy Image at 90080000 ... Image Name: Created: 2024-08-30 9:04:59 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 24061604 Bytes = 22.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Using Device Tree in place at 0000000090000000, end 000000009000a304 WARNING could not find node fsl,ls1028a-gpu: FDT_ERR_NOTFOUND. Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [ 0.000000] Linux version 6.6.46 (KernelCI@build-j301731-arm64-gcc-12-defconfig-xrgf8) (aarch64-linux-gnu-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP PREEMPT Fri Aug 30 08:41:42 UTC 2024 [ 0.000000] KASLR disabled due to lack of seed [ 0.000000] Machine model: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: ns16550a0 at MMIO 0x00000000021c0500 (options '115200n8') [ 0.000000] printk: bootconsole [ns16550a0] enabled [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x20ff7f3740-0x20ff7f6fff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000020ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] NoSplit zone start for each node [ 0.000000] NoMerge zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fbdfffff] [ 0.000000] node 0: [mem 0x0000002080000000-0x00000020ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] On node 0, zone Normal: 16896 pages in unavailable ranges [ 0.000000] cma: Reserved 32 MiB at 0x00000000f9c00000 on node -1 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv0.2 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] percpu: Embedded 22 pages/cpu s52264 r8192 d29656 u90112 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: Spectre-v3a [ 0.000000] CPU features: detected: Spectre-v4 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: detected: ARM erratum 1742098 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <5>[ 0.000000] Unknown kernel command line parameters \"n8\", will be passed to user space. <6>[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] Fallback order for Node 0: 0 <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1015296 <6>[ 0.000000] Policy zone: Normal <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] software IO TLB: area num 2. <6>[ 0.000000] software IO TLB: mapped [mem 0x00000000f5c00000-0x00000000f9c00000] (64MB) <6>[ 0.000000] Memory: 3882008K/4126720K available (16768K kernel code, 4462K rwdata, 10660K rodata, 9216K init, 642K bss, 211944K reserved, 32768K cma-reserved) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=2. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode <6>[ 0.000000] GICv3: 256 SPIs implemented <6>[ 0.000000] GICv3: 0 Extended SPIs implemented <6>[ 0.000000] Root IRQ handler: gic_handle_irq <6>[ 0.000000] GICv3: GICv3 features: 16 PPIs <6>[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006040000 <6>[ 0.000000] ITS [mem 0x06020000-0x0603ffff] <6>[ 0.000000] ITS@0x0000000006020000: allocated 65536 Devices @2080080000 (flat, esz 8, psz 64K, shr 0) <6>[ 0.000000] ITS: using cache flushing for cmd queue <6>[ 0.000000] GICv3: using LPI property table @0x0000002080030000 <6>[ 0.000000] GIC: using cache flushing for LPI property table <6>[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000002080040000 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns <6>[ 0.000000] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns <6>[ 0.008854] Console: colour dummy device 80x25 <6>[ 0.013650] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) <6>[ 0.024370] pid_max: default: 32768 minimum: 301 <6>[ 0.029333] LSM: initializing lsm=capability,integrity <6>[ 0.034853] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.042601] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.051752] RCU Tasks: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1. <6>[ 0.059195] RCU Tasks Trace: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1. <6>[ 0.067235] rcu: Hierarchical SRCU implementation. <6>[ 0.072337] rcu: Max phase no-delay instances is 1000. <6>[ 0.078021] Platform MSI: msi-controller@6020000 domain created <6>[ 0.084353] PCI/MSI: /interrupt-controller@6000000/msi-controller@6020000 domain created <6>[ 0.092836] fsl-mc MSI: msi-controller@6020000 domain created <6>[ 0.099668] EFI services will not be available. <6>[ 0.104613] smp: Bringing up secondary CPUs ... <6>[ 0.109736] Detected PIPT I-cache on CPU1 <6>[ 0.109776] GICv3: CPU1: found redistributor 1 region 0:0x0000000006060000 <6>[ 0.109785] GICv3: CPU1: using allocated LPI pending table @0x0000002080050000 <6>[ 0.109810] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] <6>[ 0.109872] smp: Brought up 1 node, 2 CPUs <6>[ 0.140186] SMP: Total of 2 processors activated. <6>[ 0.145198] CPU features: detected: 32-bit EL0 Support <6>[ 0.150656] CPU features: detected: 32-bit EL1 Support <6>[ 0.156108] CPU features: detected: CRC32 instructions <6>[ 0.161604] CPU: All CPU(s) started at EL2 <6>[ 0.166019] alternatives: applying system-wide alternatives <6>[ 0.173138] devtmpfs: initialized <6>[ 0.180343] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.190467] futex hash table entries: 512 (order: 3, 32768 bytes, linear) <6>[ 0.198150] pinctrl core: initialized pinctrl subsystem <6>[ 0.204178] Machine: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier <6>[ 0.211824] SoC family: QorIQ LS1028A <6>[ 0.215777] SoC ID: svr:0x870b0110, Revision: 1.0 <6>[ 0.221032] DMI not present or invalid. <6>[ 0.225827] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.232578] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.240086] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.248201] audit: initializing netlink subsys (disabled) <5>[ 0.254007] audit: type=2000 audit(0.152:1): state=initialized audit_enabled=0 res=1 <6>[ 0.254673] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.262098] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.268460] cpuidle: using governor menu <6>[ 0.279661] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.286807] ASID allocator initialised with 65536 entries <6>[ 0.293662] Serial: AMBA PL011 UART driver <6>[ 0.309413] Modules: 22272 pages in range for non-PLT usage <6>[ 0.309420] Modules: 513792 pages in range for PLT usage <6>[ 0.315741] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.328493] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page <6>[ 0.335084] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.342199] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page <6>[ 0.348789] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.355904] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page <6>[ 0.362493] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.369608] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page <6>[ 0.377258] ACPI: Interpreter disabled. <6>[ 0.382930] iommu: Default domain type: Translated <6>[ 0.388039] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.394682] SCSI subsystem initialized <6>[ 0.398932] usbcore: registered new interface driver usbfs <6>[ 0.404755] usbcore: registered new interface driver hub <6>[ 0.410400] usbcore: registered new device driver usb <6>[ 0.416089] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.423924] i2c i2c-0: IMX I2C adapter registered <6>[ 0.429192] imx-i2c 2030000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.436855] i2c i2c-1: IMX I2C adapter registered <6>[ 0.441980] imx-i2c 2040000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.449716] i2c i2c-2: IMX I2C adapter registered <6>[ 0.455188] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.460468] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.469971] PTP clock support registered <6>[ 0.474295] EDAC MC: Ver: 3.0.0 <6>[ 0.478181] scmi_core: SCMI protocol bus registered <6>[ 0.483838] FPGA manager framework <6>[ 0.487598] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.494589] vgaarb: loaded <6>[ 0.497815] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.504374] VFS: Disk quotas dquot_6.6.0 <6>[ 0.508617] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 0.515928] pnp: PnP ACPI: disabled <6>[ 0.523873] NET: Registered PF_INET protocol family <6>[ 0.529239] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 0.539000] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear) <6>[ 0.547930] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.556023] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) <6>[ 0.564367] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes, linear) <6>[ 0.572728] TCP: Hash tables configured (established 32768 bind 32768) <6>[ 0.579687] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.586758] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.594337] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.600618] RPC: Registered named UNIX socket transport module. <6>[ 0.606866] RPC: Registered udp transport module. <6>[ 0.611877] RPC: Registered tcp transport module. <6>[ 0.616887] RPC: Registered tcp-with-tls transport module. <6>[ 0.622693] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.629467] PCI: CLS 0 bytes, default 64 <6>[ 0.633860] kvm [1]: IPA Size Limit: 44 bits <6>[ 0.633965] Unpacking initramfs... <6>[ 0.642137] kvm [1]: GICv3: no GICV resource entry <6>[ 0.642142] kvm [1]: disabling GICv2 emulation <6>[ 0.647240] kvm [1]: GIC system register CPU interface enabled <6>[ 0.647255] kvm [1]: vgic interrupt IRQ9 <6>[ 0.662386] kvm [1]: Hyp mode initialized successfully <5>[ 0.670272] Initialise system trusted keyrings <6>[ 0.675175] workingset: timestamp_bits=42 max_order=20 bucket_order=0 <6>[ 0.682177] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.693897] NFS: Registering the id_resolver key type <5>[ 0.699285] Key type id_resolver registered <5>[ 0.703770] Key type id_legacy registered <6>[ 0.708097] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.715131] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 0.723005] 9p: Installing v9fs 9p2000 file system support <6>[ 0.744138] jitterentropy: Initialization failed with host not compliant with requirements: 9 <5>[ 0.753040] Key type asymmetric registered <5>[ 0.757440] Asymmetric key parser 'x509' registered <6>[ 0.762686] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 0.770435] io scheduler mq-deadline registered <6>[ 0.775273] io scheduler kyber registered <6>[ 0.779635] io scheduler bfq registered <6>[ 0.791194] pci-host-generic 1f0000000.pcie: host bridge /soc/pcie@1f0000000 ranges: <6>[ 0.799331] pci-host-generic 1f0000000.pcie: MEM 0x01f8000000..0x01f815ffff -> 0x01f8000000 <6>[ 0.808517] pci-host-generic 1f0000000.pcie: MEM 0x01f8160000..0x01f81cffff -> 0x01f8160000 <6>[ 0.817702] pci-host-generic 1f0000000.pcie: MEM 0x01f81d0000..0x01f81effff -> 0x01f81d0000 <6>[ 0.826874] pci-host-generic 1f0000000.pcie: MEM 0x01f81f0000..0x01f820ffff -> 0x01f81f0000 <6>[ 0.836046] pci-host-generic 1f0000000.pcie: MEM 0x01f8210000..0x01f822ffff -> 0x01f8210000 <6>[ 0.845216] pci-host-generic 1f0000000.pcie: MEM 0x01f8230000..0x01f824ffff -> 0x01f8230000 <6>[ 0.854382] pci-host-generic 1f0000000.pcie: MEM 0x01fc000000..0x01fc3fffff -> 0x01fc000000 <6>[ 0.863589] pci-host-generic 1f0000000.pcie: ECAM at [mem 0x1f0000000-0x1f00fffff] for [bus 00] <6>[ 0.872864] pci-host-generic 1f0000000.pcie: PCI host bridge to bus 0000:00 <6>[ 0.880193] pci_bus 0000:00: root bus resource [bus 00] <6>[ 0.885753] pci_bus 0000:00: root bus resource [mem 0x1f8000000-0x1f815ffff] <6>[ 0.893156] pci_bus 0000:00: root bus resource [mem 0x1f8160000-0x1f81cffff pref] <6>[ 0.901009] pci_bus 0000:00: root bus resource [mem 0x1f81d0000-0x1f81effff] <6>[ 0.908411] pci_bus 0000:00: root bus resource [mem 0x1f81f0000-0x1f820ffff pref] <6>[ 0.916253] pci_bus 0000:00: root bus resource [mem 0x1f8210000-0x1f822ffff] <6>[ 0.923656] pci_bus 0000:00: root bus resource [mem 0x1f8230000-0x1f824ffff pref] <6>[ 0.931500] pci_bus 0000:00: root bus resource [mem 0x1fc000000-0x1fc3fffff] <6>[ 0.938926] pci 0000:00:00.0: [1957:e100] type 00 class 0x020001 <6>[ 0.945303] pci 0000:00:00.0: BAR 0: [mem 0x1f8000000-0x1f803ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 0.956134] pci 0000:00:00.0: BAR 2: [mem 0x1f8160000-0x1f816ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 0.967399] pci 0000:00:00.0: VF BAR 0: [mem 0x1f81d0000-0x1f81dffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 0.978488] pci 0000:00:00.0: VF BAR 2: [mem 0x1f81f0000-0x1f81fffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 0.990029] pci 0000:00:00.0: PME# supported from D0 D3hot <6>[ 0.995844] pci 0000:00:00.0: VF(n) BAR0 space: [mem 0x1f81d0000-0x1f81effff 64bit] (contains BAR0 for 2 VFs) <6>[ 1.006144] pci 0000:00:00.0: VF(n) BAR2 space: [mem 0x1f81f0000-0x1f820ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 1.017083] pci 0000:00:00.1: [1957:e100] type 00 class 0x020001 <6>[ 1.023468] pci 0000:00:00.1: BAR 0: [mem 0x1f8040000-0x1f807ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.034295] pci 0000:00:00.1: BAR 2: [mem 0x1f8170000-0x1f817ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.045561] pci 0000:00:00.1: VF BAR 0: [mem 0x1f8210000-0x1f821ffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 1.056649] pci 0000:00:00.1: VF BAR 2: [mem 0x1f8230000-0x1f823ffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 1.068204] pci 0000:00:00.1: PME# supported from D0 D3hot <6>[ 1.074032] pci 0000:00:00.1: VF(n) BAR0 space: [mem 0x1f8210000-0x1f822ffff 64bit] (contains BAR0 for 2 VFs) <6>[ 1.084327] pci 0000:00:00.1: VF(n) BAR2 space: [mem 0x1f8230000-0x1f824ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 1.095270] pci 0000:00:00.2: [1957:e100] type 00 class 0x020001 <6>[ 1.101639] pci 0000:00:00.2: BAR 0: [mem 0x1f8080000-0x1f80bffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.112450] pci 0000:00:00.2: BAR 2: [mem 0x1f8180000-0x1f818ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.123712] pci 0000:00:00.2: PME# supported from D0 D3hot <6>[ 1.129716] pci 0000:00:00.3: [1957:ee01] type 00 class 0x088001 <6>[ 1.136079] pci 0000:00:00.3: BAR 0: [mem 0x1f8100000-0x1f811ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.146887] pci 0000:00:00.3: BAR 2: [mem 0x1f8190000-0x1f819ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.158146] pci 0000:00:00.3: PME# supported from D0 D3hot <6>[ 1.164122] pci 0000:00:00.4: [1957:ee02] type 00 class 0x088001 <6>[ 1.170483] pci 0000:00:00.4: BAR 0: [mem 0x1f8120000-0x1f813ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.181298] pci 0000:00:00.4: BAR 2: [mem 0x1f81a0000-0x1f81affff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.192564] pci 0000:00:00.4: PME# supported from D0 D3hot <6>[ 1.198572] pci 0000:00:00.5: [1957:eef0] type 00 class 0x020801 <6>[ 1.204936] pci 0000:00:00.5: BAR 0: [mem 0x1f8140000-0x1f815ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.215747] pci 0000:00:00.5: BAR 2: [mem 0x1f81b0000-0x1f81bffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.227019] pci 0000:00:00.5: BAR 4: [mem 0x1fc000000-0x1fc3fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.237859] pci 0000:00:00.5: PME# supported from D0 D3hot <6>[ 1.243884] pci 0000:00:00.6: [1957:e100] type 00 class 0x020001 <6>[ 1.250255] pci 0000:00:00.6: BAR 0: [mem 0x1f80c0000-0x1f80fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.261067] pci 0000:00:00.6: BAR 2: [mem 0x1f81c0000-0x1f81cffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.272327] pci 0000:00:00.6: PME# supported from D0 D3hot <6>[ 1.279052] pci 0000:00:1f.0: [1957:e001] type 00 class 0x080700 <6>[ 1.285444] OF: /soc/pcie@1f0000000: no msi-map translation for id 0xf8 on (null) <6>[ 1.397849] pci 0000:00:00.1: enabling device (0400 -> 0402) <6>[ 1.404660] pci 0000:00:00.1: enetc_fixup_clear_rss_rfs+0x0/0x5c took 108607 usecs <6>[ 1.488814] Freeing initrd memory: 23492K <6>[ 1.517829] pci 0000:00:00.2: enabling device (0400 -> 0402) <6>[ 1.524141] pci 0000:00:00.2: enetc_fixup_clear_rss_rfs+0x0/0x5c took 108906 usecs <6>[ 1.637825] pci 0000:00:00.6: enabling device (0400 -> 0402) <6>[ 1.644098] pci 0000:00:00.6: enetc_fixup_clear_rss_rfs+0x0/0x5c took 109373 usecs <6>[ 1.652045] OF: /soc/pcie@1f0000000: no iommu-map translation for id 0xf8 on (null) <6>[ 1.660212] pcieport 0000:00:1f.0: PME: Signaling with IRQ 19 <6>[ 1.666491] pcieport 0000:00:1f.0: AER: enabled with IRQ 19 <6>[ 1.673137] layerscape-pcie 3400000.pcie: host bridge /soc/pcie@3400000 ranges: <6>[ 1.680815] layerscape-pcie 3400000.pcie: IO 0x8000010000..0x800001ffff -> 0x0000000000 <6>[ 1.689708] layerscape-pcie 3400000.pcie: MEM 0x8040000000..0x807fffffff -> 0x0040000000 <6>[ 1.698630] layerscape-pcie 3400000.pcie: iATU: unroll F, 8 ob, 6 ib, align 4K, limit 4G <6>[ 2.707171] layerscape-pcie 3400000.pcie: Phy link never came up <6>[ 2.713569] layerscape-pcie 3400000.pcie: PCI host bridge to bus 0001:00 <6>[ 2.720603] pci_bus 0001:00: root bus resource [bus 00-ff] <6>[ 2.726406] pci_bus 0001:00: root bus resource [io 0x0000-0xffff] <6>[ 2.732910] pci_bus 0001:00: root bus resource [mem 0x8040000000-0x807fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 2.743820] pci 0001:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 2.750205] pci 0001:00:00.0: supports D1 D2 <6>[ 2.754779] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 2.762039] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 2.768992] pci 0001:00:00.0: PCI bridge to [bus 01] <6>[ 2.774394] layerscape-pcie 3500000.pcie: host bridge /soc/pcie@3500000 ranges: <6>[ 2.782065] layerscape-pcie 3500000.pcie: IO 0x8800010000..0x880001ffff -> 0x0000000000 <6>[ 2.790950] layerscape-pcie 3500000.pcie: MEM 0x8840000000..0x887fffffff -> 0x0040000000 <6>[ 2.799860] layerscape-pcie 3500000.pcie: iATU: unroll F, 8 ob, 6 ib, align 4K, limit 4G <6>[ 3.808395] layerscape-pcie 3500000.pcie: Phy link never came up <6>[ 3.814785] layerscape-pcie 3500000.pcie: PCI host bridge to bus 0002:00 <6>[ 3.821819] pci_bus 0002:00: root bus resource [bus 00-ff] <6>[ 3.827622] pci_bus 0002:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) <6>[ 3.836935] pci_bus 0002:00: root bus resource [mem 0x8840000000-0x887fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 3.847842] pci 0002:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 3.854224] pci 0002:00:00.0: supports D1 D2 <6>[ 3.858797] pci 0002:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 3.866010] pci_bus 0002:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 3.872961] pci 0002:00:00.0: PCI bridge to [bus 01] <6>[ 3.879069] EINJ: ACPI disabled. <6>[ 3.899747] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 3.908295] printk: console [ttyS0] disabled <6>[ 3.913051] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 20, base_baud = 12500000) is a 16550A <6>[ 3.922237] printk: console [ttyS0] enabled <6>[ 3.922237] printk: console [ttyS0] enabled <6>[ 3.931197] printk: bootconsole [ns16550a0] disabled <6>[ 3.931197] printk: bootconsole [ns16550a0] disabled <6>[ 3.946367] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 20, base_baud = 12500000) is a 16550A <6>[ 3.955831] SuperH (H)SCI(F) driver initialized <6>[ 3.960961] msm_serial: driver initialized <6>[ 3.965911] 2270000.serial: ttyLP2 at MMIO 0x2270000 (irq = 21, base_baud = 12500000) is a FSL_LPUART <6>[ 3.975813] STM32 USART driver initialized <5>[ 3.983247] arm-smmu 5000000.iommu: probing hardware configuration... <5>[ 3.989982] arm-smmu 5000000.iommu: SMMUv2 with: <5>[ 3.994878] arm-smmu 5000000.iommu: stage 1 translation <5>[ 4.000490] arm-smmu 5000000.iommu: stage 2 translation <5>[ 4.006089] arm-smmu 5000000.iommu: nested translation <5>[ 4.011600] arm-smmu 5000000.iommu: coherent table walk <5>[ 4.017192] arm-smmu 5000000.iommu: (IDR0.CTTW overridden by FW configuration) <5>[ 4.024795] arm-smmu 5000000.iommu: stream matching with 128 register groups <5>[ 4.032221] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) <5>[ 4.039040] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 <5>[ 4.045768] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA <5>[ 4.052494] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA <5>[ 4.059443] arm-smmu 5000000.iommu: preserved 0 boot mappings <4>[ 4.065611] arm-smmu 5000000.iommu: Failed to disable prefetcher [errata #841119 and #826419], check ACR.CACHE_LOCK <6>[ 4.079667] loop: module loaded <6>[ 4.090606] megasas: 07.725.01.00-rc1 <6>[ 4.096773] spi-nor spi1.0: w25q128fw (16384 Kbytes) <6>[ 4.118129] spi-nor spi0.0: w25q32jwm (4096 Kbytes) <5>[ 4.152994] 5 fixed-partitions partitions found on MTD device 20c0000.spi <5>[ 4.160116] Creating 5 MTD partitions on \"20c0000.spi\": <5>[ 4.165626] 0x000000000000-0x000000010000 : \"rcw\" <5>[ 4.171442] 0x000000010000-0x0000001e0000 : \"failsafe bootloader\" <5>[ 4.178453] 0x000000200000-0x000000210000 : \"configuration store\" <5>[ 4.185425] 0x000000210000-0x0000003e0000 : \"bootloader\" <5>[ 4.191666] 0x0000003e0000-0x000000400000 : \"bootloader environment\" <6>[ 4.201730] tun: Universal TUN/TAP device driver, 1.6 <6>[ 4.207738] thunder_xcv, ver 1.0 <6>[ 4.211267] thunder_bgx, ver 1.0 <6>[ 4.214792] nicpf, ver 1.0 <6>[ 4.218365] fsl_enetc 0000:00:00.0: Adding to iommu group 0 <6>[ 4.224636] fsl_enetc_mdio 0000:00:00.3: Adding to iommu group 1 <6>[ 4.337826] fsl_enetc_mdio 0000:00:00.3: enabling device (0400 -> 0402) <6>[ 4.361348] fsl_enetc_ptp 0000:00:00.4: Adding to iommu group 2 <6>[ 4.367650] fsl_enetc_ptp 0000:00:00.4: enabling device (0404 -> 0406) <4>[ 4.374604] ptp_qoriq: device tree node missing required elements, try automatic configuration <6>[ 4.383630] pps pps0: new PPS source ptp0 <6>[ 4.388451] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 4.395973] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 4.401597] hclge is initializing <6>[ 4.405199] e1000: Intel(R) PRO/1000 Network Driver <6>[ 4.410357] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 4.416408] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 4.421652] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 4.427876] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 4.433556] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 4.439427] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 4.445983] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 4.452419] sky2: driver version 1.30 <6>[ 4.457275] VFIO - User Level meta-driver version: 0.3 <6>[ 4.463020] dwc3 3100000.usb: Adding to iommu group 3 <6>[ 4.469237] dwc3 3110000.usb: Adding to iommu group 4 <6>[ 4.476873] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 4.482665] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 <6>[ 4.490734] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000808002000010 <6>[ 4.500439] xhci-hcd xhci-hcd.0.auto: irq 98, io mem 0x03100000 <6>[ 4.506732] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 4.512504] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 <6>[ 4.520455] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed <6>[ 4.527665] hub 1-0:1.0: USB hub found <6>[ 4.531713] hub 1-0:1.0: 1 port detected <6>[ 4.536101] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 4.544840] hub 2-0:1.0: USB hub found <6>[ 4.548879] hub 2-0:1.0: 1 port detected <6>[ 4.553308] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 4.559098] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 <6>[ 4.567179] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000808002000010 <6>[ 4.576901] xhci-hcd xhci-hcd.1.auto: irq 99, io mem 0x03110000 <6>[ 4.583191] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 4.588963] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 <6>[ 4.596915] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed <6>[ 4.604055] hub 3-0:1.0: USB hub found <6>[ 4.608099] hub 3-0:1.0: 1 port detected <6>[ 4.612477] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 4.621130] hub 4-0:1.0: USB hub found <6>[ 4.625170] hub 4-0:1.0: 1 port detected <6>[ 4.629942] usbcore: registered new interface driver usb-storage <6>[ 4.638340] i2c_dev: i2c /dev entries driver <6>[ 4.646391] sp805-wdt c000000.watchdog: registration successful <6>[ 4.652748] sp805-wdt c010000.watchdog: registration successful <6>[ 4.661076] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver <6>[ 4.669987] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.676458] sdhci: Copyright(c) Pierre Ossman <6>[ 4.681620] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.688579] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.695211] sdhci-esdhc 2150000.mmc: Adding to iommu group 5 <6>[ 4.701197] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.701454] sdhci-esdhc 2140000.mmc: Adding to iommu group 6 <6>[ 4.715676] usbcore: registered new interface driver usbhid <6>[ 4.721547] usbhid: USB HID core driver <6>[ 4.727969] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available <6>[ 4.737858] mmc1: SDHCI controller on 2140000.mmc [2140000.mmc] using ADMA <6>[ 4.738348] mmc0: SDHCI controller on 2150000.mmc [2150000.mmc] using ADMA <6>[ 4.747663] NET: Registered PF_PACKET protocol family <6>[ 4.757674] 9pnet: Installing 9P2000 support <5>[ 4.762266] Key type dns_resolver registered <6>[ 4.773005] registered taskstats version 1 <5>[ 4.777454] Loading compiled-in X.509 certificates <6>[ 4.790232] fsl-edma 22c0000.dma-controller: Adding to iommu group 7 <6>[ 4.798107] pcieport 0001:00:00.0: Adding to iommu group 8 <6>[ 4.804068] pcieport 0001:00:00.0: PME: Signaling with IRQ 104 <6>[ 4.810404] pcieport 0001:00:00.0: AER: enabled with IRQ 104 <6>[ 4.816538] pcieport 0002:00:00.0: Adding to iommu group 9 <6>[ 4.822529] pcieport 0002:00:00.0: PME: Signaling with IRQ 105 <6>[ 4.828820] pcieport 0002:00:00.0: AER: enabled with IRQ 105 <6>[ 4.862580] mmc0: new HS400 MMC card at address 0001 <6>[ 4.868271] mmcblk0: mmc0:0001 S0J56X 7.34 GiB <6>[ 4.873015] usb 3-1: new high-speed USB device number 2 using xhci-hcd <6>[ 4.881131] mmcblk0: p1 p2 <6>[ 4.884664] mmcblk0boot0: mmc0:0001 S0J56X 31.5 MiB <6>[ 4.890834] mmcblk0boot1: mmc0:0001 S0J56X 31.5 MiB <6>[ 4.896871] mmcblk0rpmb: mmc0:0001 S0J56X 4.00 MiB, chardev (234:0) <6>[ 4.941860] fsl_enetc 0000:00:00.0: enabling device (0400 -> 0402) <6>[ 4.949277] fsl_enetc 0000:00:00.0: no MAC address specified for SI1, using 96:17:51:e0:a9:d0 <6>[ 4.958167] fsl_enetc 0000:00:00.0: no MAC address specified for SI2, using 56:2b:b8:a3:96:64 <6>[ 4.970442] input: buttons0 as /devices/platform/buttons0/input/input0 <6>[ 5.015224] fsl_enetc 0000:00:00.0 eth0: PHY [0000:00:00.3:05] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL) <6>[ 5.026873] fsl_enetc 0000:00:00.0 eth0: configuring for inband/sgmii link mode <6>[ 5.083970] hub 3-1:1.0: USB hub found <6>[ 5.088100] hub 3-1:1.0: 7 ports detected <6>[ 8.094808] fsl_enetc 0000:00:00.0 eth0: Link is Up - 1Gbps/Full - flow control rx/tx <5>[ 8.121862] Sending DHCP requests ., OK <6>[ 8.142121] IP-Config: Got DHCP answer from 172.16.0.254, my address is 172.16.0.106 <6>[ 8.150234] IP-Config: Complete: <6>[ 8.153745] device=eth0, hwaddr=00:e0:4b:6e:9b:2b, ipaddr=172.16.0.106, mask=255.255.255.0, gw=172.16.0.254 <6>[ 8.164269] host=172.16.0.106, domain=lava.lan, nis-domain=(none) <6>[ 8.171120] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 8.171137] nameserver0=8.8.8.8 <6>[ 8.181961] clk: Disabling unused clocks <6>[ 8.186290] ALSA device list: <6>[ 8.189534] No soundcards found. <6>[ 8.197895] Freeing unused kernel memory: 9216K <6>[ 8.202933] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 8.270695] udevd[104]: starting version 3.2.9 <5>[ 9.377822] random: crng init done <27>[ 9.384318] udevd[104]: specified user 'tss' unknown <27>[ 9.389708] udevd[104]: specified group 'tss' unknown <30>[ 9.396130] udevd[105]: starting eudev-3.2.9 <6>[ 9.648444] EDAC MC0: Giving out device to module fsl_ddr_edac controller fsl_mc_err: DEV fsl_mc_err (INTERRUPT) <6>[ 9.686615] fsl_ddr_edac acquired irq 111 for MC <6>[ 9.695189] fsl_enetc 0000:00:00.0 enp0s0f0: renamed from eth0 (while UP) <4>[ 9.712984] rtc-rv8803 0-0032: Voltage low, temperature compensation stopped. <6>[ 9.721696] fsl_ddr_edac MC err registered <6>[ 9.726942] NET: Registered PF_INET6 protocol family <4>[ 9.730211] rtc-rv8803 0-0032: Voltage low, data loss detected. <6>[ 9.743111] Segment Routing with IPv6 <4>[ 9.747795] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 9.748078] In-situ OAM (IOAM) with IPv6 <6>[ 9.768041] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. <4>[ 9.784081] wm8904 2-001a: supply DCVDD not found, using dummy regulator <4>[ 9.791623] wm8904 2-001a: supply DBVDD not found, using dummy regulator <4>[ 9.798768] rtc-rv8803 0-0032: Voltage low, data is invalid. <6>[ 9.807576] at24 0-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <6>[ 9.817361] rtc-rv8803 0-0032: registered as rtc0 <4>[ 9.822589] wm8904 2-001a: supply AVDD not found, using dummy regulator <4>[ 9.832196] at24 1-0057: supply vcc not found, using dummy regulator <4>[ 9.839611] wm8904 2-001a: supply CPVDD not found, using dummy regulator <4>[ 9.847307] wm8904 2-001a: supply MICVDD not found, using dummy regulator <4>[ 9.858863] rtc-rv8803 0-0032: Voltage low, data is invalid. <3>[ 9.868587] rtc-rv8803 0-0032: hctosys: unable to read the hardware clock <6>[ 9.868992] at24 1-0057: 8192 byte 24c64 EEPROM, writable, 32 bytes/write <6>[ 9.886807] CAN device driver interface <4>[ 9.887343] at24 2-0050: supply vcc not found, using dummy regulator <6>[ 9.898351] wm8904 2-001a: revision A <6>[ 9.902805] sl28cpld-wdt 2000000.i2c:sl28cpld@4a:watchdog@4: initial timeout 6 sec <6>[ 9.923176] at24 2-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <6>[ 9.956806] ftm-alarm 2800000.timer: registered as rtc1 <6>[ 9.983173] caam 8000000.crypto: Entropy delay = 3200 <6>[ 9.992705] usbcore: registered new device driver onboard-usb-hub <6>[ 10.004090] caam 8000000.crypto: Instantiated RNG4 SH0 <6>[ 10.009630] caam 8000000.crypto: Instantiated RNG4 SH1 <6>[ 10.015177] caam 8000000.crypto: device ID = 0x0a12070000000000 (Era 10) <6>[ 10.029880] caam 8000000.crypto: job rings = 4, qi = 0 <6>[ 10.076641] mali-dp f080000.display: Adding to iommu group 10 <6>[ 10.091164] etnaviv etnaviv: bound f0c0000.gpu (ops gpu_ops [etnaviv]) <6>[ 10.123612] etnaviv-gpu f0c0000.gpu: model: GC7000, revision: 6202 <6>[ 10.132073] [drm] Initialized etnaviv 1.4.0 20151214 for etnaviv on minor 0 <6>[ 10.159749] caam_jr 8010000.jr: Adding to iommu group 11 <6>[ 10.169960] caam algorithms registered in /proc/crypto <6>[ 10.175486] caam 8000000.crypto: registering rng-caam <6>[ 10.180986] caam 8000000.crypto: rng crypto API alg registered prng-caam <6>[ 10.188168] caam_jr 8020000.jr: Adding to iommu group 12 <6>[ 10.194431] caam_jr 8030000.jr: Adding to iommu group 13 <6>[ 10.200631] caam_jr 8040000.jr: Adding to iommu group 14 <6>[ 10.364245] hub 3-1:1.0: USB hub found <6>[ 10.368510] hub 3-1:1.0: 7 ports detected done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # <6>[ 10.523948] hub 3-1:1.0: USB hub found <6>[ 10.528052] hub 3-1:1.0: 7 ports detected / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-491750/environment . /lava-491750/environment / # /lava-491750/bin/lava-test-runner /lava-491750/0 /lava-491750/bin/lava-test-runner /lava-491750/0 + export 'TESTRUN_ID=0_dmesg' + c<8>[ 11.025159] d /lava-491750/0/tests/0_dmesg + cat uuid + UUID=491750_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 11.046602] <8>[ 11.068156] <8>[ 11.091859] + set +x <8>[ 11.101580] / #