Trying 0.0.0.0... Connected to 0. Escape character is '^]'. U-Boot 2019.04-linux4sam_6.2-icp (May 18 2022 - 22:17:10 +0000), Build: HEAD-0.00-20220518221710 CPU: SAMA7 Reset Source : SYSRESET Watchdog enabled DRAM: 1 GiB MMC: emmc@e0830000: 0 Loading Environment from SPI Flash... SF: Detected sst26vf016b with page size 256 Bytes, erase size 4 KiB, total 2 MiB OK In: serial Out: serial Err: serial VPD: BOARD_SERIAL K1FT90005, MAC 00:A0:A5:5C:6D:A2 Net: eth0: port0 [PRIME], eth1: port1, eth2: port2, eth3: port3, eth4: port4, eth5: port5, eth6: port6, eth7: port7 POST memory PASSED POST env PASSED POST vpd PASSED => setenv autoload no setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp dhcp port4 Waiting for PHY auto negotiation to complete...... done BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 BOOTP broadcast 4 DHCP client bound to address 172.16.0.126 (1758 ms) => setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 => tftp 0x62000000 511630/tftp-deploy-cta9pgkj/kernel/zImage tftp 0x62000000 511630/tftp-deploy-cta9pgkj/kernel/zImage tftp 0x62000000 511630/tftp-deploy-cta9pgkj/kernel/zImage port4 Waiting for PHY auto negotiation to complete...... done Using port4 device TFTP from server 10.228.65.1; our IP address is 172.16.0.126; sending through gateway 172.16.0.254 Filename '511630/tftp-deploy-cta9pgkj/kernel/zImage'. Load address: 0x62000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# 1.7 MiB/s done Bytes transferred = 11440640 (ae9200 hex) => tftp 0x68080000 511630/tftp-deploy-cta9pgkj/ramdisk/ramdisk.cpio.gz.uboot tftp 0x68080000 511630/tftp-deploy-cta9pgkj/ramdisk/ramdisk.cpio.gz.uboot tftp 0x68080000 511630/tftp-deploy-cta9pgkj/ramdisk/ramdisk.cpio.gz.uboot port4 Waiting for PHY auto negotiation to complete....... done Using port4 device TFTP from server 10.228.65.1; our IP address is 172.16.0.126; sending through gateway 172.16.0.254 Filename '511630/tftp-deploy-cta9pgkj/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x68080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ##################################################### 2.4 MiB/s done Bytes transferred = 17940579 (111c063 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x68000000 511630/tftp-deploy-cta9pgkj/dtb/lan966x-kontron-kswitch-d10-mmt-6g-2gs.dtb tftp 0x68000000 511630/tftp-deploy-cta9pgkj/dtb/lan966x-kontron-kswitch-d10-mmt-6g-2gs.dtb tftp 0x68000000 511630/tftp-deploy-cta9pgkj/dtb/lan966x-kontron-kswitch-d10-mmt-6g-2gs.dtb port4 Waiting for PHY auto negotiation to complete....... done Using port4 device TFTP from server 10.228.65.1; our IP address is 172.16.0.126; sending through gateway 172.16.0.254 Filename '511630/tftp-deploy-cta9pgkj/dtb/lan966x-kontron-kswitch-d10-mmt-6g-2gs.dtb'. Load address: 0x68000000 Loading: *# 2 KiB/s done Bytes transferred = 14136 (3738 hex) => setenv bootargs 'console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x62000000 0x68080000 0x68000000 bootz 0x62000000 0x68080000 0x68000000 bootz 0x62000000 0x68080000 0x68000000 ## Loading init Ramdisk from Legacy Image at 68080000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 17940515 Bytes = 17.1 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 68000000 Booting using the fdt blob at 0x68000000 Using Device Tree in place at 68000000, end 68006737 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.12.0-rc2 (KernelCI@build-j363793-arm-gcc-12-multi-v7-defconfig-zpgq5) (arm-linux-gnueabihf-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Tue Nov 5 20:23:39 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Kontron KSwitch D10 MMT 6G-2GS [ 0.000000] earlycon: atmel_serial0 at MMIO 0xe0040200 (options '115200n8') [ 0.000000] printk: legacy bootconsole [atmel_serial0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x9c000000 on node -1 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000060000000-0x000000008fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000090000000-0x000000009fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000060000000-0x000000009fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000060000000-0x000000009fffffff] [ 0.000000] percpu: Embedded 17 pages/cpu s40844 r8192 d20596 u69632 [ 0.000000] Kernel command line: console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 262144 <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] arch_timer: cp15 timer(s) running at 37.50MHz (virt). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x8a60dd6a9, max_idle_ns: 440795204056 ns <6>[ 0.000003] sched_clock: 56 bits at 38MHz, resolution 26ns, wraps every 2199023255540ns <6>[ 0.008281] Switching to timer-based delay loop, resolution 26ns <6>[ 0.017494] Console: colour dummy device 80x30 <6>[ 0.022176] Calibrating delay loop (skipped), value calculated using timer frequency.. 75.00 BogoMIPS (lpj=375000) <6>[ 0.032768] CPU: Testing write buffer coherency: ok <6>[ 0.037876] pid_max: default: 32768 minimum: 301 <6>[ 0.043023] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.050497] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.060141] CPU0: update cpu_capacity 1024 <6>[ 0.064408] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.130807] Setting up static identity map for 0x60300000 - 0x603000ac <6>[ 0.138625] rcu: Hierarchical SRCU implementation. <6>[ 0.143626] rcu: Max phase no-delay instances is 1000. <6>[ 0.151622] EFI services will not be available. <6>[ 0.156765] smp: Bringing up secondary CPUs ... <6>[ 0.161477] smp: Brought up 1 node, 1 CPU <6>[ 0.165715] SMP: Total of 1 processors activated (75.00 BogoMIPS). <6>[ 0.172281] CPU: All CPU(s) started in SVC mode. <6>[ 0.177232] Memory: 924512K/1048576K available (16384K kernel code, 2542K rwdata, 6784K rodata, 2048K init, 431K bss, 56264K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.193807] devtmpfs: initialized <6>[ 0.203554] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 <6>[ 0.211802] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.221901] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.232747] pinctrl core: initialized pinctrl subsystem <6>[ 0.241215] DMI not present or invalid. <6>[ 0.247655] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.256546] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.267383] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.267562] cpuidle: using governor menu <6>[ 0.278487] No ATAGs? <6>[ 0.280985] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.289228] hw-breakpoint: maximum watchpoint size is 8 bytes. <6>[ 0.298639] Serial: AMBA PL011 UART driver <6>[ 0.320897] platform e2004064.pinctrl: Fixed dependency cycle(s) with /soc/pinctrl@e2004064/phy-int-pins <6>[ 0.367517] at_xdmac e0068000.dma-controller: 16 channels, mapped at 0x(ptrval) <6>[ 0.399026] iommu: Default domain type: Translated <6>[ 0.403973] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.421802] SCSI subsystem initialized <6>[ 0.431544] usbcore: registered new interface driver usbfs <6>[ 0.437232] usbcore: registered new interface driver hub <6>[ 0.442899] usbcore: registered new device driver usb <6>[ 0.449732] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.454917] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.464294] PTP clock support registered <6>[ 0.468684] EDAC MC: Ver: 3.0.0 <6>[ 0.518919] scmi_core: SCMI protocol bus registered <6>[ 0.529337] vgaarb: loaded <6>[ 0.539423] clocksource: Switched to clocksource arch_sys_counter <6>[ 0.596024] NET: Registered PF_INET protocol family <6>[ 0.601612] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 0.612938] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) <6>[ 0.621560] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.629531] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 0.637622] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) <6>[ 0.645412] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.652145] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 0.658995] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 0.666658] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.745736] RPC: Registered named UNIX socket transport module. <6>[ 0.751885] RPC: Registered udp transport module. <6>[ 0.756799] RPC: Registered tcp transport module. <6>[ 0.761792] RPC: Registered tcp-with-tls transport module. <6>[ 0.767524] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.774285] PCI: CLS 0 bytes, default 64 <5>[ 0.780538] Initialise system trusted keyrings <6>[ 0.800767] Trying to unpack rootfs image as initramfs... <6>[ 0.879715] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 0.887067] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.924253] NFS: Registering the id_resolver key type <5>[ 0.929687] Key type id_resolver registered <5>[ 0.933999] Key type id_legacy registered <6>[ 0.938327] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.945310] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <5>[ 1.000205] Key type asymmetric registered <5>[ 1.004471] Asymmetric key parser 'x509' registered <6>[ 1.009905] bounce: pool size: 64 pages <6>[ 1.013975] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 1.021601] io scheduler mq-deadline registered <6>[ 1.026346] io scheduler kyber registered <6>[ 1.030687] io scheduler bfq registered <6>[ 1.140297] pinctrl-ocelot e2004064.pinctrl: driver registered <6>[ 1.199686] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 1.639889] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 1.697949] msm_serial: driver initialized <6>[ 1.702864] SuperH (H)SCI(F) driver initialized <6>[ 1.707827] STMicroelectronics ASC driver initialized <6>[ 1.713325] STM32 USART driver initialized <5>[ 1.772253] random: crng init done <6>[ 1.868817] brd: module loaded <6>[ 1.900730] loop: module loaded <6>[ 1.910966] atmel_usart_serial atmel_usart_serial.0.auto: Using FIFO (32 data) <6>[ 1.919285] atmel_usart_serial.0.auto: ttyAT0 at MMIO 0xe0040200 (irq = 32, base_baud = 12500000) is a ATMEL_SERIAL <6>[ 1.930111] printk: legacy console [ttyAT0] enabled <6>[ 1.930111] printk: legacy console [ttyAT0] enabled <6>[ 1.940308] printk: legacy bootconsole [atmel_serial0] disabled <6>[ 1.940308] printk: legacy bootconsole [atmel_serial0] disabled <6>[ 2.163586] CAN device driver interface <6>[ 2.169054] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 2.176547] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 2.181805] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.188020] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 2.193681] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 2.205169] pegasus: Pegasus/Pegasus II USB Ethernet driver <6>[ 2.211146] usbcore: registered new interface driver pegasus <6>[ 2.217075] usbcore: registered new interface driver asix <6>[ 2.222783] usbcore: registered new interface driver ax88179_178a <6>[ 2.229158] usbcore: registered new interface driver cdc_ether <6>[ 2.235298] usbcore: registered new interface driver smsc75xx <6>[ 2.241342] usbcore: registered new interface driver smsc95xx <6>[ 2.247357] usbcore: registered new interface driver net1080 <6>[ 2.253323] usbcore: registered new interface driver cdc_subset <6>[ 2.259559] usbcore: registered new interface driver zaurus <6>[ 2.265416] usbcore: registered new interface driver cdc_ncm <6>[ 2.277041] usbcore: registered new interface driver usb-storage <6>[ 2.563656] i2c_dev: i2c /dev entries driver <6>[ 2.656230] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.662788] sdhci: Copyright(c) Pierre Ossman <6>[ 2.670230] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.678800] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.811587] usbcore: registered new interface driver usbhid <6>[ 2.817416] usbhid: USB HID core driver <6>[ 2.863293] NET: Registered PF_INET6 protocol family <6>[ 2.901289] Segment Routing with IPv6 <6>[ 2.905261] In-situ OAM (IOAM) with IPv6 <6>[ 2.909666] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.916952] NET: Registered PF_PACKET protocol family <6>[ 2.922353] can: controller area network core <6>[ 2.926999] NET: Registered PF_CAN protocol family <6>[ 2.932081] can: raw protocol <6>[ 2.935266] can: broadcast manager protocol <6>[ 2.939760] can: netlink gateway - max_hops=1 <5>[ 2.945133] Key type dns_resolver registered <6>[ 2.950082] ThumbEE CPU extension supported. <5>[ 2.954601] Registering SWP/SWPB emulation handler <5>[ 3.170357] Loading compiled-in X.509 certificates <6>[ 5.558796] Freeing initrd memory: 17524K <6>[ 15.689599] clk: Disabling unused clocks <6>[ 15.693797] PM: genpd: Disabling unused power domains <6>[ 15.705057] Freeing unused kernel image (initmem) memory: 2048K <6>[ 15.709148] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 15.972288] udevd[76]: starting version 3.2.9 <27>[ 15.991649] udevd[76]: specified user 'tss' unknown <27>[ 15.994426] udevd[76]: specified group 'tss' unknown <30>[ 16.004355] udevd[77]: starting eudev-3.2.9 <6>[ 17.945865] atmel_aes e004c000.crypto: version: 0x702 <6>[ 17.963148] MAC addr was not set, use random MAC <6>[ 18.004494] atmel_sha e006c000.crypto: version: 0x700 <6>[ 18.052532] atmel_aes e004c000.crypto: Atmel AES - Using dma0chan0, dma0chan1 for DMA transfers <6>[ 18.156119] atmel_sha e006c000.crypto: using dma0chan3 for DMA transfers <6>[ 18.160595] atmel_sha e006c000.crypto: Atmel SHA1/SHA256/SHA224/SHA384/SHA512 <6>[ 18.188466] atmel_spi e0064400.spi: Using dma0chan4 (tx) and dma0chan5 (rx) for DMA transfers <6>[ 18.194783] atmel_spi e0064400.spi: Using FIFO (32 data) <6>[ 18.204225] at91_i2c e0044600.i2c: using dma0chan2 (tx) and dma0chan6 (rx) for DMA transfers <6>[ 18.270566] at91_i2c e0044600.i2c: AT91 i2c bus driver (hw version: 0x820). <6>[ 18.285060] sfp sfp1: Host maximum power 2.5W <6>[ 18.299047] atmel_spi e0064400.spi: Atmel SPI Controller version 0x401 at 0xe0064400 (irq 41) <6>[ 18.322109] at91_i2c e0070600.i2c: using dma0chan7 (tx) and dma0chan8 (rx) for DMA transfers <6>[ 18.367593] at91_i2c e0070600.i2c: AT91 i2c bus driver (hw version: 0x820). <6>[ 18.455317] sfp sfp0: Host maximum power 2.5W <6>[ 18.528902] MAC addr was not set, use random MAC <6>[ 18.537328] hwmon hwmon0: temp1_input not attached to any thermal zone <6>[ 18.626415] sfp sfp1: module AGILENT HFBR-5710L rev sn 0304140555048996 dc 030414 <6>[ 18.771027] sfp sfp0: module AGILENT HFBR-5710L rev sn 0304140604014998 dc 030414 <6>[ 18.778036] lan966x-switch e0000000.switch eth2: switched to inband/1000base-x link mode <6>[ 18.791880] lan966x-switch e0000000.switch (unnamed net_device) (uninitialized): switched to inband/1000base-x link mode done Saving random seed: OK Starting network: OK Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # # / # export SHELL=/bin/sh export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-511630/environment . /lava-511630/environment . /lava-511630/environment / # /lava-511630/bin/lava-test-runner /lava-511630/0 /lava-511630/bin/lava-test-runner /lava-511630/0 /lava-511630/bin/lava-test-runner /lava-511630/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-511630/0/tests/0_dmesg + cat uuid + UUID=511630_1.5.2.4.1 + set +x <8>[ 22.437822] + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 22.514186] <8>[ 22.581481] <8>[ 22.648717] + set +x <8>[ 22.657707] / #