Trying 192.168.56.21... Connected to conserv1. Escape character is '^]'. ser2net port telnet,3007 device serialdev, /dev/serial/by-path/platform-fd500000.pcie-pci-0000:01:00.0-usb-0:1.2.4.4:1.0-port0, 115200n81, local=false [] (Debian GNU/Linux) G12B:BL:6e7c85:2a3b91;FEAT:E0F83180:402000;POC:B;RCY:0;SPINOR:0;0. bl2_stage_init 0x01 bl2_stage_init 0x81 hw id: 0x0000 - pwm id 0x01 bl2_stage_init 0xc1 bl2_stage_init 0x02 L0:00000000 L1:20000703 L2:00008067 L3:14000000 B2:00402000 B1:e0f83180 TE: 58124 BL2 Built : 15:22:05, Aug 28 2019. g12b g1bf2b53 - luan.yuan@droid15-sz Board ID = 1 Set A53 clk to 24M Set A73 clk to 24M Set clk81 to 24M A53 clk: 1200 MHz A73 clk: 1200 MHz CLK81: 166.6M smccc: 00012a91 DDR driver_vesion: LPDDR4_PHY_V_0_1_18 build time: Aug 28 2019 15:22:01 board id: 1 Load FIP HDR from SPI, src: 0x00010000, des: 0xfffd0000, size: 0x00004000, part: 0 fw parse done Load ddrfw from SPI, src: 0x00030000, des: 0xfffd0000, size: 0x0000c000, part: 0 Load ddrfw from SPI, src: 0x00014000, des: 0xfffd0000, size: 0x00004000, part: 0 PIEI prepare done fastboot data load fastboot data verify verify result: 266 Cfg max: 1, cur: 1. Board id: 255. Force loop cfg LPDDR4 probe ddr clk to 1584MHz Load ddrfw from SPI, src: 0x00018000, des: 0xfffd0000, size: 0x0000c000, part: 0 dmc_version 0001 Check phy result INFO : End of CA training INFO : End of initialization INFO : Training has run successfully! Check phy result INFO : End of initialization INFO : End of read enable training INFO : End of fine write leveling INFO : End of Write leveling coarse delay INFO : Training has run successfully! Check phy result INFO : End of initialization INFO : End of read dq deskew training INFO : End of MPR read delay center optimization INFO : End of write delay center optimization INFO : End of read delay center optimization INFO : End of max read latency training INFO : Training has run successfully! 1D training succeed Load ddrfw from SPI, src: 0x00024000, des: 0xfffd0000, size: 0x0000c000, part: 0 Check phy result INFO : End of initialization INFO : End of 2D read delay Voltage center optimization INFO : End of 2D read delay Voltage center optimization INFO : End of 2D write delay Voltage center optimization INFO : End of 2D write delay Voltage center optimization INFO : Training has run successfully! channel==0 RxClkDly_Margin_A0==88 ps 9 TxDqDly_Margin_A0==98 ps 10 RxClkDly_Margin_A1==88 ps 9 TxDqDly_Margin_A1==98 ps 10 TrainedVREFDQ_A0==74 TrainedVREFDQ_A1==74 VrefDac_Margin_A0==25 DeviceVref_Margin_A0==40 VrefDac_Margin_A1==25 DeviceVref_Margin_A1==40 channel==1 RxClkDly_Margin_A0==98 ps 10 TxDqDly_Margin_A0==98 ps 10 RxClkDly_Margin_A1==98 ps 10 TxDqDly_Margin_A1==88 ps 9 TrainedVREFDQ_A0==77 TrainedVREFDQ_A1==77 VrefDac_Margin_A0==22 DeviceVref_Margin_A0==37 VrefDac_Margin_A1==22 DeviceVref_Margin_A1==37 dwc_ddrphy_apb_wr((0<<20)|(2<<16)|(0<<12)|(0xb0):0004 soc_vref_reg_value 0x 00000019 0000001a 00000017 00000019 00000018 00000019 00000019 00000017 00000018 00000016 00000017 00000016 00000018 00000019 00000017 00000019 00000018 00000019 00000019 00000018 00000016 00000018 00000018 00000019 00000018 00000017 00000019 00000019 0000001a 00000017 00000019 00000017 dram_vref_reg_value 0x 00000060 2D training succeed aml_ddr_fw_vesion: LPDDR4_PHY_V_0_1_18 build time: Aug 28 2019 13:54:19 auto size-- 65535DDR cs0 size: 2048MB DDR cs1 size: 2048MB DMC_DDR_CTRL: 00e00024DDR size: 3928MB cs0 DataBus test pass cs1 DataBus test pass cs0 AddrBus test pass cs1 AddrBus test pass 100bdlr_step_size ps== 420 result report boot times 0Enable ddr reg access Load FIP HDR from SPI, src: 0x00010000, des: 0x01700000, size: 0x00004000, part: 0 Load BL3X from SPI, src: 0x0003c000, des: 0x0172c000, size: 0x000c0000, part: 0 0.0;M3 CHK:0;cm4_sp_mode 0 MVN_1=0x00000000 MVN_2=0x00000000 [Image: g12b_v1.1.3390-6ac5299 2019-09-26 14:10:05 luan.yuan@droid15-sz] OPS=0x10 ring efuse init chipver efuse init 29 0b 10 00 01 05 19 00 00 17 38 33 33 42 42 50 [0.018960 Inits done] secure task start! high task start! low task start! run into bl31 NOTICE: BL31: v1.3(release):4fc40b1 NOTICE: BL31: Built : 15:58:17, May 22 2019 NOTICE: BL31: G12A normal boot! NOTICE: BL31: BL33 decompress pass ERROR: Error initializing runtime service opteed_fast U-Boot 2024.01-rc4+ (Dec 14 2023 - 01:31:33 -0500) Libre Computer AML-A311D-CC Model: Libre Computer AML-A311D-CC Alta SoC: Amlogic Meson G12B (A311D) Revision 29:b (10:2) DRAM: 2 GiB (effective 3.8 GiB) Core: 408 devices, 31 uclasses, devicetree: separate WDT: Not starting watchdog@f0d0 MMC: mmc@ffe05000: 1, mmc@ffe07000: 0 Loading Environment from FAT... Card did not respond to voltage select! : -110 ** Bad device specification mmc 0 ** Card did not respond to voltage select! : -110 ** Bad device specification mmc 0 ** Couldn't find partition mmc 0 Card did not respond to voltage select! : -110 ** Bad device specification mmc 0 ** Couldn't find partition mmc 0 Error: could not access storage. G12B:BL:6e7c85:2a3b91;FEAT:E0F83180:402000;POC:B;RCY:0;SPINOR:0;0. bl2_stage_init 0x01 bl2_stage_init 0x81 hw id: 0x0000 - pwm id 0x01 bl2_stage_init 0xc1 bl2_stage_init 0x02 L0:00000000 L1:20000703 L2:00008067 L3:14000000 B2:00402000 B1:e0f83180 TE: 58124 BL2 Built : 15:22:05, Aug 28 2019. g12b g1bf2b53 - luan.yuan@droid15-sz Board ID = 1 Set A53 clk to 24M Set A73 clk to 24M Set clk81 to 24M A53 clk: 1200 MHz A73 clk: 1200 MHz CLK81: 166.6M smccc: 00012a91 DDR driver_vesion: LPDDR4_PHY_V_0_1_18 build time: Aug 28 2019 15:22:01 board id: 1 Load FIP HDR from SPI, src: 0x00010000, des: 0xfffd0000, size: 0x00004000, part: 0 fw parse done Load ddrfw from SPI, src: 0x00030000, des: 0xfffd0000, size: 0x0000c000, part: 0 Load ddrfw from SPI, src: 0x00014000, des: 0xfffd0000, size: 0x00004000, part: 0 PIEI prepare done fastboot data load fastboot data verify verify result: 266 Cfg max: 1, cur: 1. Board id: 255. Force loop cfg LPDDR4 probe ddr clk to 1584MHz Load ddrfw from SPI, src: 0x00018000, des: 0xfffd0000, size: 0x0000c000, part: 0 dmc_version 0001 Check phy result INFO : End of CA training INFO : End of initialization INFO : Training has run successfully! Check phy result INFO : End of initialization INFO : End of read enable training INFO : End of fine write leveling INFO : End of Write leveling coarse delay INFO : Training has run successfully! Check phy result INFO : End of initialization INFO : End of read dq deskew training INFO : End of MPR read delay center optimization INFO : End of write delay center optimization INFO : End of read delay center optimization INFO : End of max read latency training INFO : Training has run successfully! 1D training succeed Load ddrfw from SPI, src: 0x00024000, des: 0xfffd0000, size: 0x0000c000, part: 0 Check phy result INFO : End of initialization INFO : End of 2D read delay Voltage center optimization INFO : End of 2D read delay Voltage center optimization INFO : End of 2D write delay Voltage center optimization INFO : End of 2D write delay Voltage center optimization INFO : Training has run successfully! channel==0 RxClkDly_Margin_A0==88 ps 9 TxDqDly_Margin_A0==98 ps 10 RxClkDly_Margin_A1==88 ps 9 TxDqDly_Margin_A1==98 ps 10 TrainedVREFDQ_A0==74 TrainedVREFDQ_A1==74 VrefDac_Margin_A0==24 DeviceVref_Margin_A0==40 VrefDac_Margin_A1==24 DeviceVref_Margin_A1==40 channel==1 RxClkDly_Margin_A0==98 ps 10 TxDqDly_Margin_A0==98 ps 10 RxClkDly_Margin_A1==88 ps 9 TxDqDly_Margin_A1==88 ps 9 TrainedVREFDQ_A0==77 TrainedVREFDQ_A1==77 VrefDac_Margin_A0==22 DeviceVref_Margin_A0==37 VrefDac_Margin_A1==24 DeviceVref_Margin_A1==37 dwc_ddrphy_apb_wr((0<<20)|(2<<16)|(0<<12)|(0xb0):0004 soc_vref_reg_value 0x 00000019 0000001a 00000017 00000019 00000018 00000019 00000019 00000017 00000018 00000016 00000018 00000015 00000017 00000018 00000017 00000019 00000018 0000001a 00000019 00000018 00000017 00000018 00000017 00000019 00000018 00000018 00000019 00000019 0000001a 00000017 00000018 00000017 dram_vref_reg_value 0x 0000005f 2D training succeed aml_ddr_fw_vesion: LPDDR4_PHY_V_0_1_18 build time: Aug 28 2019 13:54:19 auto size-- 65535DDR cs0 size: 2048MB DDR cs1 size: 2048MB DMC_DDR_CTRL: 00e00024DDR size: 3928MB cs0 DataBus test pass cs1 DataBus test pass cs0 AddrBus test pass cs1 AddrBus test pass 100bdlr_step_size ps== 420 result report boot times 0Enable ddr reg access Load FIP HDR from SPI, src: 0x00010000, des: 0x01700000, size: 0x00004000, part: 0 Load BL3X from SPI, src: 0x0003c000, des: 0x0172c000, size: 0x000c0000, part: 0 0.0;M3 CHK:0;cm4_sp_mode 0 MVN_1=0x00000000 MVN_2=0x00000000 [Image: g12b_v1.1.3390-6ac5299 2019-09-26 14:10:05 luan.yuan@droid15-sz] OPS=0x10 ring efuse init chipver efuse init 29 0b 10 00 01 05 19 00 00 17 38 33 33 42 42 50 [0.018961 Inits done] secure task start! high task start! low task start! run into bl31 NOTICE: BL31: v1.3(release):4fc40b1 NOTICE: BL31: Built : 15:58:17, May 22 2019 NOTICE: BL31: G12A normal boot! NOTICE: BL31: BL33 decompress pass ERROR: Error initializing runtime service opteed_fast U-Boot 2024.01-rc4+ (Dec 14 2023 - 01:31:33 -0500) Libre Computer AML-A311D-CC Model: Libre Computer AML-A311D-CC Alta SoC: Amlogic Meson G12B (A311D) Revision 29:b (10:2) DRAM: 2 GiB (effective 3.8 GiB) Core: 408 devices, 31 uclasses, devicetree: separate WDT: Not starting watchdog@f0d0 MMC: mmc@ffe05000: 1, mmc@ffe07000: 0 Loading Environment from FAT... Card did not respond to voltage select! : -110 ** Bad device specification mmc 0 ** Card did not respond to voltage select! : -110 ** Bad device specification mmc 0 ** Couldn't find partition mmc 0 Card did not respond to voltage select! : -110 ** Bad device specification mmc 0 ** Couldn't find partition mmc 0 Error: could not access storage. Net: eth0: ethernet@ff3f0000 starting USB... Bus usb@ff500000: Register 3000140 NbrPorts 3 Starting the controller USB XHCI 1.10 scanning bus usb@ff500000 for devices... G12B:BL:6e7c85:2a3b91;FEAT:E0F83180:402000;POC:B;RCY:0;SPINOR:0;0. bl2_stage_init 0x01 bl2_stage_init 0x81 hw id: 0x0000 - pwm id 0x01 bl2_stage_init 0xc1 bl2_stage_init 0x02 L0:00000000 L1:20000703 L2:00008067 L3:14000000 B2:00402000 B1:e0f83180 TE: 58124 BL2 Built : 15:22:05, Aug 28 2019. g12b g1bf2b53 - luan.yuan@droid15-sz Board ID = 1 Set A53 clk to 24M Set A73 clk to 24M Set clk81 to 24M A53 clk: 1200 MHz A73 clk: 1200 MHz CLK81: 166.6M smccc: 00012a92 DDR driver_vesion: LPDDR4_PHY_V_0_1_18 build time: Aug 28 2019 15:22:01 board id: 1 Load FIP HDR from SPI, src: 0x00010000, des: 0xfffd0000, size: 0x00004000, part: 0 fw parse done Load ddrfw from SPI, src: 0x00030000, des: 0xfffd0000, size: 0x0000c000, part: 0 Load ddrfw from SPI, src: 0x00014000, des: 0xfffd0000, size: 0x00004000, part: 0 PIEI prepare done fastboot data load fastboot data verify verify result: 266 Cfg max: 1, cur: 1. Board id: 255. Force loop cfg LPDDR4 probe ddr clk to 1584MHz Load ddrfw from SPI, src: 0x00018000, des: 0xfffd0000, size: 0x0000c000, part: 0 dmc_version 0001 Check phy result INFO : End of CA training INFO : End of initialization INFO : Training has run successfully! Check phy result INFO : End of initialization INFO : End of read enable training INFO : End of fine write leveling INFO : End of Write leveling coarse delay INFO : Training has run successfully! Check phy result INFO : End of initialization INFO : End of read dq deskew training INFO : End of MPR read delay center optimization INFO : End of write delay center optimization INFO : End of read delay center optimization INFO : End of max read latency training INFO : Training has run successfully! 1D training succeed Load ddrfw from SPI, src: 0x00024000, des: 0xfffd0000, size: 0x0000c000, part: 0 Check phy result INFO : End of initialization INFO : End of 2D read delay Voltage center optimization INFO : End of 2D read delay Voltage center optimization INFO : End of 2D write delay Voltage center optimization INFO : End of 2D write delay Voltage center optimization INFO : Training has run successfully! channel==0 RxClkDly_Margin_A0==88 ps 9 TxDqDly_Margin_A0==98 ps 10 RxClkDly_Margin_A1==88 ps 9 TxDqDly_Margin_A1==98 ps 10 TrainedVREFDQ_A0==74 TrainedVREFDQ_A1==74 VrefDac_Margin_A0==25 DeviceVref_Margin_A0==40 VrefDac_Margin_A1==25 DeviceVref_Margin_A1==40 channel==1 RxClkDly_Margin_A0==98 ps 10 TxDqDly_Margin_A0==98 ps 10 RxClkDly_Margin_A1==88 ps 9 TxDqDly_Margin_A1==88 ps 9 TrainedVREFDQ_A0==77 TrainedVREFDQ_A1==77 VrefDac_Margin_A0==22 DeviceVref_Margin_A0==37 VrefDac_Margin_A1==24 DeviceVref_Margin_A1==37 dwc_ddrphy_apb_wr((0<<20)|(2<<16)|(0<<12)|(0xb0):0004 soc_vref_reg_value 0x 00000019 0000001a 00000017 00000019 00000018 00000018 00000018 00000017 00000018 00000016 00000018 00000015 00000017 00000018 00000017 00000019 00000018 00000019 00000019 00000018 00000017 00000018 00000018 00000019 00000018 00000017 00000019 00000019 0000001a 00000016 00000019 00000017 dram_vref_reg_value 0x 00000060 2D training succeed aml_ddr_fw_vesion: LPDDR4_PHY_V_0_1_18 build time: Aug 28 2019 13:54:19 auto size-- 65535DDR cs0 size: 2048MB DDR cs1 size: 2048MB DMC_DDR_CTRL: 00e00024DDR size: 3928MB cs0 DataBus test pass cs1 DataBus test pass cs0 AddrBus test pass cs1 AddrBus test pass 100bdlr_step_size ps== 420 result report boot times 0Enable ddr reg access Load FIP HDR from SPI, src: 0x00010000, des: 0x01700000, size: 0x00004000, part: 0 Load BL3X from SPI, src: 0x0003c000, des: 0x0172c000, size: 0x000c0000, part: 0 0.0;M3 CHK:0;cm4_sp_mode 0 MVN_1=0x00000000 MVN_2=0x00000000 [Image: g12b_v1.1.3390-6ac5299 2019-09-26 14:10:05 luan.yuan@droid15-sz] OPS=0x10 ring efuse init chipver efuse init 29 0b 10 00 01 05 19 00 00 17 38 33 33 42 42 50 [0.018961 Inits done] secure task start! high task start! low task start! run into bl31 NOTICE: BL31: v1.3(release):4fc40b1 NOTICE: BL31: Built : 15:58:17, May 22 2019 NOTICE: BL31: G12A normal boot! NOTICE: BL31: BL33 decompress pass ERROR: Error initializing runtime service opteed_fast U-Boot 2024.01-rc4+ (Dec 14 2023 - 01:31:33 -0500) Libre Computer AML-A311D-CC Model: Libre Computer AML-A311D-CC Alta SoC: Amlogic Meson G12B (A311D) Revision 29:b (10:2) DRAM: 2 GiB (effective 3.8 GiB) Core: 408 devices, 31 uclasses, devicetree: separate WDT: Not starting watchdog@f0d0 MMC: mmc@ffe05000: 1, mmc@ffe07000: 0 Loading Environment from FAT... Card did not respond to voltage select! : -110 ** Bad device specification mmc 0 ** Card did not respond to voltage select! : -110 ** Bad device specification mmc 0 ** Couldn't find partition mmc 0 Card did not respond to voltage select! : -110 ** Bad device specification mmc 0 ** Couldn't find partition mmc 0 Error: could not access storage. Net: eth0: ethernet@ff3f0000 starting USB... Bus usb@ff500000: Register 3000140 NbrPorts 3 Starting the controller USB XHCI 1.10 scanning bus usb@ff500000 for devices... G12B:BL:6e7c85:2a3b91;FEAT:E0F83180:402000;POC:B;RCY:0;SPINOR:0;0. bl2_stage_init 0x01 bl2_stage_init 0x81 hw id: 0x0000 - pwm id 0x01 bl2_stage_init 0xc1 bl2_stage_init 0x02 L0:00000000 L1:20000703 L2:00008067 L3:14000000 B2:00402000 B1:e0f83180 TE: 58159 BL2 Built : 15:22:05, Aug 28 2019. g12b g1bf2b53 - luan.yuan@droid15-sz Board ID = 1 Set A53 clk to 24M Set A73 clk to 24M Set clk81 to 24M A53 clk: 1200 MHz A73 clk: 1200 MHz CLK81: 166.6M smccc: 00012ab5 DDR driver_vesion: LPDDR4_PHY_V_0_1_18 build time: Aug 28 2019 15:22:01 board id: 1 Load FIP HDR from SPI, src: 0x00010000, des: 0xfffd0000, size: 0x00004000, part: 0 fw parse done Load ddrfw from SPI, src: 0x00030000, des: 0xfffd0000, size: 0x0000c000, part: 0 Load ddrfw from SPI, src: 0x00014000, des: 0xfffd0000, size: 0x00004000, part: 0 PIEI prepare done fastboot data load fastboot data verify verify result: 266 Cfg max: 1, cur: 1. Board id: 255. Force loop cfg LPDDR4 probe ddr clk to 1584MHz Load ddrfw from SPI, src: 0x00018000, des: 0xfffd0000, size: 0x0000c000, part: 0 dmc_version 0001 Check phy result INFO : End of CA training INFO : End of initialization INFO : Training has run successfully! Check phy result INFO : End of initialization INFO : End of read enable training INFO : End of fine write leveling INFO : End of Write leveling coarse delay INFO : Training has run successfully! Check phy result INFO : End of initialization INFO : End of read dq deskew training INFO : End of MPR read delay center optimization INFO : End of write delay center optimization INFO : End of read delay center optimization INFO : End of max read latency training INFO : Training has run successfully! 1D training succeed Load ddrfw from SPI, src: 0x00024000, des: 0xfffd0000, size: 0x0000c000, part: 0 Check phy result INFO : End of initialization INFO : End of 2D read delay Voltage center optimization INFO : End of 2D read delay Voltage center optimization INFO : End of 2D write delay Voltage center optimization INFO : End of 2D write delay Voltage center optimization INFO : Training has run successfully! channel==0 RxClkDly_Margin_A0==88 ps 9 TxDqDly_Margin_A0==98 ps 10 RxClkDly_Margin_A1==88 ps 9 TxDqDly_Margin_A1==88 ps 9 TrainedVREFDQ_A0==74 TrainedVREFDQ_A1==74 VrefDac_Margin_A0==25 DeviceVref_Margin_A0==40 VrefDac_Margin_A1==25 DeviceVref_Margin_A1==40 channel==1 RxClkDly_Margin_A0==98 ps 10 TxDqDly_Margin_A0==98 ps 10 RxClkDly_Margin_A1==88 ps 9 TxDqDly_Margin_A1==88 ps 9 TrainedVREFDQ_A0==77 TrainedVREFDQ_A1==77 VrefDac_Margin_A0==22 DeviceVref_Margin_A0==37 VrefDac_Margin_A1==24 DeviceVref_Margin_A1==37 dwc_ddrphy_apb_wr((0<<20)|(2<<16)|(0<<12)|(0xb0):0004 soc_vref_reg_value 0x 00000019 00000019 00000017 00000019 00000018 00000019 00000018 00000017 00000018 00000016 00000018 00000015 00000018 00000019 00000018 00000019 00000018 0000001a 00000019 00000018 00000017 00000018 00000017 00000019 00000018 00000017 00000019 00000019 0000001a 00000016 00000019 00000017 dram_vref_reg_value 0x 00000060 2D training succeed aml_ddr_fw_vesion: LPDDR4_PHY_V_0_1_18 build time: Aug 28 2019 13:54:19 auto size-- 65535DDR cs0 size: 2048MB DDR cs1 size: 2048MB DMC_DDR_CTRL: 00e00024DDR size: 3928MB cs0 DataBus test pass cs1 DataBus test pass cs0 AddrBus test pass cs1 AddrBus test pass 100bdlr_step_size ps== 420 result report boot times 0Enable ddr reg access Load FIP HDR from SPI, src: 0x00010000, des: 0x01700000, size: 0x00004000, part: 0 Load BL3X from SPI, src: 0x0003c000, des: 0x0172c000, size: 0x000c0000, part: 0 0.0;M3 CHK:0;cm4_sp_mode 0 MVN_1=0x00000000 MVN_2=0x00000000 [Image: g12b_v1.1.3390-6ac5299 2019-09-26 14:10:05 luan.yuan@droid15-sz] OPS=0x10 ring efuse init chipver efuse init 29 0b 10 00 01 05 19 00 00 17 38 33 33 42 42 50 [0.018961 Inits done] secure task start! high task start! low task start! run into bl31 NOTICE: BL31: v1.3(release):4fc40b1 NOTICE: BL31: Built : 15:58:17, May 22 2019 NOTICE: BL31: G12A normal boot! NOTICE: BL31: BL33 decompress pass ERROR: Error initializing runtime service opteed_fast U-Boot 2024.01-rc4+ (Dec 14 2023 - 01:31:33 -0500) Libre Computer AML-A311D-CC Model: Libre Computer AML-A311D-CC Alta SoC: Amlogic Meson G12B (A311D) Revision 29:b (10:2) DRAM: 2 GiB (effective 3.8 GiB) Core: 408 devices, 31 uclasses, devicetree: separate WDT: Not starting watchdog@f0d0 MMC: mmc@ffe05000: 1, mmc@ffe07000: 0 Loading Environment from FAT... Card did not respond to voltage select! : -110 ** Bad device specification mmc 0 ** Card did not respond to voltage select! : -110 ** Bad device specification mmc 0 ** Couldn't find partition mmc 0 Card did not respond to voltage select! : -110 ** Bad device specification mmc 0 ** Couldn't find partition mmc 0 Error: could not access storage. Net: eth0: ethernet@ff3f0000 starting USB... Bus usb@ff500000: Register 3000140 NbrPorts 3 Starting the controller USB XHCI 1.10 scanning bus usb@ff500000 for devices... 3 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Hit any key to stop autoboot: 1  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp Speed: 1000, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.6.27 (9 ms) => setenv serverip 192.168.6.2 setenv serverip 192.168.6.2 => tftpboot 0x01080000 956817/tftp-deploy-_qrmi95a/kernel/uImage tftpboot 0x01080000 956817/tftp-deploy-_qrmi95a/kernel/uImage Speed: 1000, full duplex Using ethernet@ff3f0000 device TFTP from server 192.168.6.2; our IP address is 192.168.6.27 Filename '956817/tftp-deploy-_qrmi95a/kernel/uImage'. Load address: 0x1080000 Loading: *################################## UDP wrong checksum 000000ff 000054fc # UDP wrong checksum 000000ff 0000eaee ############### 43.6 MiB 15.4 MiB/s done Bytes transferred = 45713984 (2b98a40 hex) => tftpboot 0x08000000 956817/tftp-deploy-_qrmi95a/ramdisk/ramdisk.cpio.gz.uboot tftpboot 0x08000000 956817/tftp-deploy-_qrmi95a/ramdisk/ramdisk.cpio.gz.uboot Speed: 1000, full duplex Using ethernet@ff3f0000 device TFTP from server 192.168.6.2; our IP address is 192.168.6.27 Filename '956817/tftp-deploy-_qrmi95a/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x8000000 Loading: *################### UDP wrong checksum 000000ff 0000da8b UDP wrong checksum 000000ff 00003314 T ############################### 22.3 MiB 3.3 MiB/s done Bytes transferred = 23432224 (1658c20 hex) => tftpboot 0x01070000 956817/tftp-deploy-_qrmi95a/dtb/meson-g12b-a311d-libretech-cc.dtb tftpboot 0x01070000 956817/tftp-deploy-_qrmi95a/dtb/meson-g12b-a311d-libretech-cc.dtb Speed: 1000, full duplex Using ethernet@ff3f0000 device TFTP from server 192.168.6.2; our IP address is 192.168.6.27 Filename '956817/tftp-deploy-_qrmi95a/dtb/meson-g12b-a311d-libretech-cc.dtb'. Load address: 0x1070000 Loading: *################################################## 53.4 KiB 3.1 MiB/s done Bytes transferred = 54703 (d5af hex) => setenv bootargs 'console=ttyAML0,115200n8 root=/dev/nfs rw nfsroot=192.168.6.2:/var/lib/lava/dispatcher/tmp/956817/extract-nfsrootfs-uzrwqge2,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyAML0,115200n8 root=/dev/nfs rw nfsroot=192.168.6.2:/var/lib/lava/dispatcher/tmp/956817/extract-nfsrootfs-uzrwqge2,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootm 0x01080000 0x08000000 0x01070000 bootm 0x01080000 0x08000000 0x01070000 ## Booting kernel from Legacy Image at 01080000 ... Image Name: Image Type: AArch64 Linux Kernel Image (uncompressed) Data Size: 45713920 Bytes = 43.6 MiB Load Address: 01080000 Entry Point: 01080000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 08000000 ... Image Name: Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 23432160 Bytes = 22.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01070000 Booting using the fdt blob at 0x1070000 Working FDT set to 1070000 Loading Kernel Image Loading Ramdisk to 7e9a7000, end 7ffffbe0 ... OK Loading Device Tree to 000000007e996000, end 000000007e9a65ae ... OK Working FDT set to 7e996000 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 6.12.0-rc2 (KernelCI@build-j367672-arm64-gcc-12-defconfig-tngf7) (aarch64-linux-gnu-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP PREEMPT Fri Nov 8 00:30:12 UTC 2024 [ 0.000000] KASLR disabled due to lack of seed [ 0.000000] Machine model: Libre Computer AML-A311D-CC Alta [ 0.000000] efi: UEFI not found. [ 0.000000] [Firmware Bug]: Kernel image misaligned at boot, please fix your bootloader! [ 0.000000] Reserved memory: created CMA memory pool at 0x00000000e4c00000, size 256 MiB [ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool [ 0.000000] OF: reserved mem: 0x00000000e4c00000..0x00000000f4bfffff (262144 KiB) map reusable linux,cma [ 0.000000] OF: reserved mem: 0x0000000005000000..0x00000000052fffff (3072 KiB) nomap non-reusable secmon@5000000 [ 0.000000] OF: reserved mem: 0x0000000005300000..0x00000000072fffff (32768 KiB) nomap non-reusable secmon@5300000 [ 0.000000] earlycon: meson0 at MMIO 0x00000000ff803000 (options '115200n8') [ 0.000000] printk: legacy bootconsole [meson0] enabled [ 0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x00000000f4e5afff] [ 0.000000] NODE_DATA(0) allocated [mem 0xe4666a80-0xe46690bf] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x00000000f4e5afff] [ 0.000000] DMA32 empty [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000004ffffff] [ 0.000000] node 0: [mem 0x0000000005000000-0x00000000072fffff] [ 0.000000] node 0: [mem 0x0000000007300000-0x00000000f4e5afff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x00000000f4e5afff] [ 0.000000] On node 0, zone DMA: 12709 pages in unavailable ranges [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 25 pages/cpu s61656 r8192 d32552 u102400 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: ARM erratum 845719 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Kernel command line: console=ttyAML0,115200n8 root=/dev/nfs rw nfsroot=192.168.6.2:/var/lib/lava/dispatcher/tmp/956817/extract-nfsrootfs-uzrwqge2,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] Fallback order for Node 0: 0 <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1003099 <6>[ 0.000000] Policy zone: DMA <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] software IO TLB: SWIOTLB bounce buffer size adjusted to 3MB <6>[ 0.000000] software IO TLB: area num 8. <6>[ 0.000000] software IO TLB: mapped [mem 0x00000000dfc00000-0x00000000e0000000] (4MB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=6. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=6 <6>[ 0.000000] RCU Tasks: Setting shift to 3 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=6. <6>[ 0.000000] RCU Tasks Trace: Setting shift to 3 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=6. <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] Root IRQ handler: gic_handle_irq <6>[ 0.000000] GIC: Using split EOI/Deactivate mode <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns <6>[ 0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns <6>[ 0.008793] Console: colour dummy device 80x25 <6>[ 0.012937] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) <6>[ 0.023294] pid_max: default: 32768 minimum: 301 <6>[ 0.028189] LSM: initializing lsm=capability <6>[ 0.032727] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.040211] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.052298] rcu: Hierarchical SRCU implementation. <6>[ 0.053215] rcu: Max phase no-delay instances is 1000. <6>[ 0.058879] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level <6>[ 0.071583] EFI services will not be available. <6>[ 0.075233] smp: Bringing up secondary CPUs ... <6>[ 0.077132] Detected VIPT I-cache on CPU1 <6>[ 0.077252] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] <6>[ 0.078591] CPU features: detected: Spectre-v2 <6>[ 0.078605] CPU features: detected: Spectre-v4 <6>[ 0.078611] CPU features: detected: Spectre-BHB <6>[ 0.078617] CPU features: detected: ARM erratum 858921 <6>[ 0.078625] Detected VIPT I-cache on CPU2 <6>[ 0.078699] arch_timer: Enabling local workaround for ARM erratum 858921 <6>[ 0.078716] arch_timer: CPU2: Trapping CNTVCT access <6>[ 0.078726] CPU2: Booted secondary processor 0x0000000100 [0x410fd092] <6>[ 0.083580] Detected VIPT I-cache on CPU3 <6>[ 0.083625] arch_timer: Enabling local workaround for ARM erratum 858921 <6>[ 0.083634] arch_timer: CPU3: Trapping CNTVCT access <6>[ 0.083641] CPU3: Booted secondary processor 0x0000000101 [0x410fd092] <6>[ 0.087617] Detected VIPT I-cache on CPU4 <6>[ 0.087664] arch_timer: Enabling local workaround for ARM erratum 858921 <6>[ 0.087673] arch_timer: CPU4: Trapping CNTVCT access <6>[ 0.087680] CPU4: Booted secondary processor 0x0000000102 [0x410fd092] <6>[ 0.091614] Detected VIPT I-cache on CPU5 <6>[ 0.091662] arch_timer: Enabling local workaround for ARM erratum 858921 <6>[ 0.091671] arch_timer: CPU5: Trapping CNTVCT access <6>[ 0.091678] CPU5: Booted secondary processor 0x0000000103 [0x410fd092] <6>[ 0.091792] smp: Brought up 1 node, 6 CPUs <6>[ 0.213021] SMP: Total of 6 processors activated. <6>[ 0.217926] CPU: All CPU(s) started at EL2 <6>[ 0.222276] CPU features: detected: 32-bit EL0 Support <6>[ 0.227587] CPU features: detected: 32-bit EL1 Support <6>[ 0.232933] CPU features: detected: CRC32 instructions <6>[ 0.238337] alternatives: applying system-wide alternatives <6>[ 0.245526] Memory: 3557436K/4012396K available (17280K kernel code, 4898K rwdata, 11876K rodata, 10432K init, 742K bss, 187796K reserved, 262144K cma-reserved) <6>[ 0.259865] devtmpfs: initialized <6>[ 0.269057] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.273411] futex hash table entries: 2048 (order: 5, 131072 bytes, linear) <6>[ 0.284207] 21392 pages in range for non-PLT usage <6>[ 0.284217] 512912 pages in range for PLT usage <6>[ 0.285764] pinctrl core: initialized pinctrl subsystem <6>[ 0.297845] DMI not present or invalid. <6>[ 0.302136] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.306880] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.313651] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.321752] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations <6>[ 0.329243] audit: initializing netlink subsys (disabled) <5>[ 0.334987] audit: type=2000 audit(0.256:1): state=initialized audit_enabled=0 res=1 <6>[ 0.336492] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.342747] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.349009] cpuidle: using governor menu <6>[ 0.359989] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.366925] ASID allocator initialised with 65536 entries <6>[ 0.374443] Serial: AMBA PL011 UART driver <6>[ 0.385025] platform ff600000.hdmi-tx: Fixed dependency cycle(s) with /soc/vpu@ff900000 <6>[ 0.400535] platform ff600000.hdmi-tx: Fixed dependency cycle(s) with /soc/vpu@ff900000 <6>[ 0.403207] platform ff900000.vpu: Fixed dependency cycle(s) with /soc/bus@ff600000/hdmi-tx@0 <6>[ 0.416359] platform ff900000.vpu: Fixed dependency cycle(s) with /cvbs-connector <6>[ 0.419580] platform cvbs-connector: Fixed dependency cycle(s) with /soc/vpu@ff900000 <6>[ 0.428005] platform ff600000.hdmi-tx: Fixed dependency cycle(s) with /hdmi-connector <6>[ 0.435629] platform hdmi-connector: Fixed dependency cycle(s) with /soc/bus@ff600000/hdmi-tx@0 <6>[ 0.449207] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.451447] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page <6>[ 0.457928] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.464905] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page <6>[ 0.471374] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.478360] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page <6>[ 0.484829] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.491814] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page <6>[ 0.499814] ACPI: Interpreter disabled. <6>[ 0.505323] iommu: Default domain type: Translated <6>[ 0.507348] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.514033] SCSI subsystem initialized <6>[ 0.517954] usbcore: registered new interface driver usbfs <6>[ 0.523404] usbcore: registered new interface driver hub <6>[ 0.528924] usbcore: registered new device driver usb <6>[ 0.535194] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.539341] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.548661] PTP clock support registered <6>[ 0.552903] EDAC MC: Ver: 3.0.0 <6>[ 0.556557] scmi_core: SCMI protocol bus registered <6>[ 0.562211] FPGA manager framework <6>[ 0.564924] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.571861] vgaarb: loaded <6>[ 0.574429] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.580579] VFS: Disk quotas dquot_6.6.0 <6>[ 0.584555] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 0.591767] pnp: PnP ACPI: disabled <6>[ 0.600271] NET: Registered PF_INET protocol family <6>[ 0.600585] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 0.610757] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear) <6>[ 0.616762] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.624655] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) <6>[ 0.632889] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes, linear) <6>[ 0.640689] TCP: Hash tables configured (established 32768 bind 32768) <6>[ 0.647167] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.654011] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.661438] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.667529] RPC: Registered named UNIX socket transport module. <6>[ 0.673295] RPC: Registered udp transport module. <6>[ 0.678204] RPC: Registered tcp transport module. <6>[ 0.683119] RPC: Registered tcp-with-tls transport module. <6>[ 0.688812] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.695459] PCI: CLS 0 bytes, default 64 <6>[ 0.699727] Unpacking initramfs... <6>[ 0.705839] kvm [1]: nv: 554 coarse grained trap handlers <6>[ 0.709153] kvm [1]: IPA Size Limit: 40 bits <6>[ 0.714759] kvm [1]: vgic interrupt IRQ9 <6>[ 0.717469] kvm [1]: Hyp nVHE mode initialized successfully <5>[ 0.724798] Initialise system trusted keyrings <6>[ 0.728051] workingset: timestamp_bits=42 max_order=20 bucket_order=0 <6>[ 0.734783] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.740850] NFS: Registering the id_resolver key type <5>[ 0.745855] Key type id_resolver registered <5>[ 0.750225] Key type id_legacy registered <6>[ 0.754478] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.761351] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 0.769108] 9p: Installing v9fs 9p2000 file system support <5>[ 0.815834] Key type asymmetric registered <5>[ 0.815876] Asymmetric key parser 'x509' registered <6>[ 0.819738] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 0.827258] io scheduler mq-deadline registered <6>[ 0.831998] io scheduler kyber registered <6>[ 0.836264] io scheduler bfq registered <6>[ 0.842159] irq_meson_gpio: 100 to 8 gpio interrupt mux initialized <6>[ 0.862528] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 0.893899] soc soc0: Amlogic Meson G12B (A311D) Revision 29:b (10:2) Detected <6>[ 0.907596] Serial: 8250/16550 driver, 4 ports<6>[ 0.912201] ff803000.serial: ttyAML0 at MMIO 0xff803000 (irq = 14, base_baud = 1500000) is a meson_uart <6>[ 0.921832] printk: legacy console [ttyAML0] enabled <6>[ 0.921832] printk: legacy console [ttyAML0] enabled <6>[ 0.926626] printk: legacy bootconsole [meson0] disabled <6>[ 0.926626] printk: legacy bootconsole [meson0] disabled <6>[ 0.939226] msm_serial: driver initialized <6>[ 0.942621] SuperH (H)SCI(F) driver initialized <6>[ 0.947083] STM32 USART driver initialized <5>[ 0.953304] random: crng init done <6>[ 0.959021] loop: module loaded <6>[ 0.960302] megasas: 07.727.03.00-rc1 <6>[ 0.969282] tun: Universal TUN/TAP device driver, 1.6 <6>[ 0.970507] thunder_xcv, ver 1.0 <6>[ 0.972441] thunder_bgx, ver 1.0 <6>[ 0.975923] nicpf, ver 1.0 <6>[ 0.980482] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 0.986301] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 0.991890] hclge is initializing <6>[ 0.995427] e1000: Intel(R) PRO/1000 Network Driver <6>[ 1.000509] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 1.006536] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 1.011689] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 1.017872] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 1.023475] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.029308] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 1.035794] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 1.042565] sky2: driver version 1.30 <6>[ 1.047656] VFIO - User Level meta-driver version: 0.3 <6>[ 1.055201] usbcore: registered new interface driver usb-storage <6>[ 1.061396] i2c_dev: i2c /dev entries driver <6>[ 1.072456] sdhci: Secure Digital Host Controller Interface driver <6>[ 1.073259] sdhci: Copyright(c) Pierre Ossman <6>[ 1.079024] Synopsys Designware Multimedia Card Interface Driver <6>[ 1.085534] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 1.093189] meson-sm: secure-monitor enabled <6>[ 1.095776] usbcore: registered new interface driver usbhid <6>[ 1.100326] usbhid: USB HID core driver <6>[ 1.115161] NET: Registered PF_PACKET protocol family <6>[ 1.115248] 9pnet: Installing 9P2000 support <5>[ 1.119402] Key type dns_resolver registered <6>[ 1.130973] registered taskstats version 1 <5>[ 1.131127] Loading compiled-in X.509 certificates <6>[ 1.139811] Demotion targets for Node 0: null <6>[ 1.182810] dwc3-meson-g12a ffe09000.usb: USB2 ports: 2 <6>[ 1.182855] dwc3-meson-g12a ffe09000.usb: USB3 ports: 1 <4>[ 1.193030] dwc2 ff400000.usb: supply vusb_d not found, using dummy regulator <4>[ 1.195647] dwc2 ff400000.usb: supply vusb_a not found, using dummy regulator <6>[ 1.203188] dwc2 ff400000.usb: EPs: 7, dedicated fifos, 712 entries in SPRAM <6>[ 1.212478] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 1.215890] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 <6>[ 1.223877] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228fe6c hci version 0x110 quirks 0x0000808000000010 <6>[ 1.233410] xhci-hcd xhci-hcd.0.auto: irq 16, io mem 0xff500000 <6>[ 1.239635] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 1.245260] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 <6>[ 1.253144] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed <6>[ 1.260424] hub 1-0:1.0: USB hub found <6>[ 1.263915] hub 1-0:1.0: 2 ports detected <6>[ 1.269975] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 1.276871] hub 2-0:1.0: USB hub found <6>[ 1.280458] hub 2-0:1.0: 1 port detected <6>[ 1.311385] meson-gx-mmc ffe05000.mmc: Got CD GPIO <6>[ 1.321516] meson-gx-mmc ffe07000.mmc: allocated mmc-pwrseq <6>[ 1.353363] Trying to probe devices needed for running init ... <6>[ 1.518465] usb 1-1: new high-speed USB device number 2 using xhci-hcd <6>[ 1.661814] mmc0: new ultra high speed SDR104 SDXC card at address e624 <6>[ 1.663922] mmcblk0: mmc0:e624 SD64G 59.5 GiB <6>[ 1.669903] mmcblk0: p1 <6>[ 1.671790] Freeing initrd memory: 22880K <6>[ 1.708226] hub 1-1:1.0: USB hub found <6>[ 1.708515] hub 1-1:1.0: 4 ports detected <6>[ 1.774569] usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd <6>[ 1.820895] hub 2-1:1.0: USB hub found <6>[ 1.821716] hub 2-1:1.0: 4 ports detected <6>[ 13.650521] clk: Disabling unused clocks <6>[ 13.650766] PM: genpd: Disabling unused power domains <6>[ 13.654404] ALSA device list: <6>[ 13.657596] No soundcards found. <6>[ 13.671463] Freeing unused kernel memory: 10432K <6>[ 13.671593] Run /init as init process Loading, please wait... Starting systemd-udevd version 252.22-1~deb12u1 <6>[ 14.142830] meson8b-dwmac ff3f0000.ethernet: IRQ eth_wake_irq not found <6>[ 14.144072] meson8b-dwmac ff3f0000.ethernet: IRQ eth_lpi not found <6>[ 14.153184] meson8b-dwmac ff3f0000.ethernet: IRQ sfty not found <6>[ 14.156753] meson8b-dwmac ff3f0000.ethernet: PTP uses main clock <6>[ 14.173601] meson-vrtc ff8000a8.rtc: registered as rtc0 <6>[ 14.173664] meson-vrtc ff8000a8.rtc: setting system clock to 1970-01-01T00:00:14 UTC (14) <4>[ 14.182531] meson-pwm ff802000.pwm: using obsolete compatible, please consider updating dt <6>[ 14.185146] meson8b-dwmac ff3f0000.ethernet: User ID: 0x11, Synopsys ID: 0x37 <6>[ 14.192372] mc: Linux media interface: v0.10 <6>[ 14.197760] meson8b-dwmac ff3f0000.ethernet: DWMAC1000 <6>[ 14.197771] meson8b-dwmac ff3f0000.ethernet: DMA HW capability register supported <6>[ 14.215460] meson8b-dwmac ff3f0000.ethernet: RX Checksum Offload Engine supported <6>[ 14.223409] meson8b-dwmac ff3f0000.ethernet: COE Type 2 <6>[ 14.224227] Registered IR keymap rc-empty <6>[ 14.227853] panfrost ffe40000.gpu: clock rate = 24000000 <3>[ 14.227906] panfrost ffe40000.gpu: error -ENODEV: _opp_set_regulators: no regulator (mali) found <6>[ 14.228606] meson8b-dwmac ff3f0000.ethernet: TX Checksum insertion supported <6>[ 14.228614] meson8b-dwmac ff3f0000.ethernet: Wake-Up On Lan supported <6>[ 14.229626] panfrost ffe40000.gpu: mali-g52 id 0x7212 major 0x0 minor 0x0 status 0x0 <6>[ 14.229638] panfrost ffe40000.gpu: features: 00000000,00000cf7, issues: 00000000,00000400 <6>[ 14.229645] panfrost ffe40000.gpu: Features: L2:0x07110206 Shader:0x00000000 Tiler:0x00000809 Mem:0x1 MMU:0x00002830 AS:0xff JS:0x7 <6>[ 14.229654] panfrost ffe40000.gpu: shader_present=0x3 l2_present=0x1 <3>[ 14.231438] debugfs: Directory 'ff800280.cec' with parent 'regmap' already present! <6>[ 14.232936] rc rc0: meson-ir as /devices/platform/soc/ff800000.bus/ff808000.ir/rc/rc0 <6>[ 14.238479] meson8b-dwmac ff3f0000.ethernet: Normal descriptors <6>[ 14.247541] input: meson-ir as /devices/platform/soc/ff800000.bus/ff808000.ir/rc/rc0/input0 <6>[ 14.255828] meson8b-dwmac ff3f0000.ethernet: Ring mode enabled <6>[ 14.261710] rc rc0: sw decoder init <6>[ 14.269758] meson8b-dwmac ff3f0000.ethernet: Enable RX Mitigation via HW Watchdog Timer <6>[ 14.277803] meson-ir ff808000.ir: receiver initialized <6>[ 14.297119] meson-drm ff900000.vpu: Queued 2 outputs on vpu <6>[ 14.306971] videodev: Linux video capture interface: v2.00 <6>[ 14.319140] [drm] Initialized panfrost 1.2.0 for ffe40000.gpu on minor 0 <6>[ 14.359164] meson-dw-hdmi ff600000.hdmi-tx: Detected HDMI TX controller v2.01a with HDCP (meson_dw_hdmi_phy) <6>[ 14.379719] meson-dw-hdmi ff600000.hdmi-tx: registered DesignWare HDMI I2C bus driver <4>[ 14.382009] meson_vdec: module is from the staging directory, the quality is unknown, you have been warned. <6>[ 14.400024] meson-drm ff900000.vpu: bound ff600000.hdmi-tx (ops meson_dw_hdmi_ops [meson_dw_hdmi]) <3>[ 14.406903] meson-drm ff900000.vpu: DSI transceiver device is disabled <6>[ 14.413634] [drm] Initialized meson 1.0.0 for ff900000.vpu on minor 1 <6>[ 14.424867] cpufreq: cpufreq_online: CPU2: Running at unlisted initial frequency: 999999 KHz, changing to: 1000000 KHz <6>[ 14.454681] meson8b-dwmac ff3f0000.ethernet end0: renamed from eth0 <6>[ 14.455463] usbcore: registered new device driver onboard-usb-dev <4>[ 14.462474] rc rc0: two consecutive events of type space <6>[ 14.611211] Console: switching to colour frame buffer device 128x48 <6>[ 14.649140] meson-drm ff900000.vpu: [drm] fb0: mesondrmfb frame buffer device <6>[ 14.892209] hub 1-1:1.0: USB hub found <6>[ 14.892488] hub 1-1:1.0: 4 ports detected <6>[ 14.897321] onboard-usb-dev 1-1: USB disconnect, device number 2 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/end0 found done. Begin: Waiting up to 180 secs for any network device to become available ... done. IP-Config: end0 hardware address de:ca:d3:e3:c6:63 mtu 1500 DHCP <6>[ 15.119544] meson8b-dwmac ff3f0000.ethernet end0: Register MEM_TYPE_PAGE_POOL RxQ-0 <6>[ 15.210542] meson8b-dwmac ff3f0000.ethernet end0: PHY [mdio_mux-0.0:00] driver [RTL8211F Gigabit Ethernet] (irq=32) <6>[ 15.226581] meson8b-dwmac ff3f0000.ethernet end0: No Safety Features support found <6>[ 15.228772] meson8b-dwmac ff3f0000.ethernet end0: PTP not supported by HW <6>[ 15.236138] meson8b-dwmac ff3f0000.ethernet end0: configuring for phy/rgmii link mode <6>[ 15.266460] usb 1-1: new high-speed USB device number 3 using xhci-hcd <6>[ 15.468145] hub 1-1:1.0: USB hub found <6>[ 15.468435] hub 1-1:1.0: 4 ports detected <6>[ 15.660195] usb 2-1: reset SuperSpeed USB device number 2 using xhci-hcd <6>[ 15.916789] usb 2-1: reset SuperSpeed USB device number 2 using xhci-hcd IP-Config: no response after 2 secs - giving up IP-Config: end0 hardware address de:ca:d3:e3:c6:63 mtu 1500 DHCP <6>[ 18.195023] meson8b-dwmac ff3f0000.ethernet end0: Link is Up - 1Gbps/Full - flow control off IP-Config: end0 guessed broadcast address 192.168.6.255 IP-Config: end0 complete (dhcp from 192.168.6.1): address: 192.168.6.27 broadcast: 192.168.6.255 netmask: 255.255.255.0 gateway: 192.168.6.1 dns0 : 10.255.253.1 dns1 : 0.0.0.0 rootserver: 192.168.6.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 19.404645] systemd[1]: System time before build time, advancing clock. <6>[ 19.464507] NET: Registered PF_INET6 protocol family <6>[ 19.467640] Segment Routing with IPv6 <6>[ 19.468010] In-situ OAM (IOAM) with IPv6 <30>[ 19.517824] systemd[1]: systemd 252.22-1~deb12u1 running in system mode (+PAM +AUDIT +SELINUX +APPARMOR +IMA +SMACK +SECCOMP +GCRYPT -GNUTLS +OPENSSL +ACL +BLKID +CURL +ELFUTILS +FIDO2 +IDN2 -IDN +IPTC +KMOD +LIBCRYPTSETUP +LIBFDISK +PCRE2 -PWQUALITY +P11KIT +QRENCODE +TPM2 +BZIP2 +LZ4 +XZ +ZLIB +ZSTD -BPF_FRAMEWORK -XKBCOMMON +UTMP +SYSVINIT default-hierarchy=unified) <30>[ 19.545285] systemd[1]: Detected architecture arm64. Welcome to [1mDebian GNU/Linux 12 (bookworm)[0m! <30>[ 19.564032] systemd[1]: Hostname set to . <30>[ 20.276070] systemd[1]: Queued start job for default target graphical.target. <30>[ 20.324793] systemd[1]: Created slice system-getty.slice - Slice /system/getty. [[0;32m OK [0m] Created slice [0;1;39msystem-getty.slice[0m - Slice /system/getty. <30>[ 20.343447] systemd[1]: Created slice system-modprobe.slice - Slice /system/modprobe. [[0;32m OK [0m] Created slice [0;1;39msystem-modpr…lice[0m - Slice /system/modprobe. <30>[ 20.363488] systemd[1]: Created slice system-serial\x2dgetty.slice - Slice /system/serial-getty. [[0;32m OK [0m] Created slice [0;1;39msystem-seria…[0m - Slice /system/serial-getty. <30>[ 20.383199] systemd[1]: Created slice user.slice - User and Session Slice. [[0;32m OK [0m] Created slice [0;1;39muser.slice[0m - User and Session Slice. <30>[ 20.398704] systemd[1]: Started systemd-ask-password-console.path - Dispatch Password Requests to Console Directory Watch. [[0;32m OK [0m] Started [0;1;39msystemd-ask-passwo…quests to Console Directory Watch. <30>[ 20.418634] systemd[1]: Started systemd-ask-password-wall.path - Forward Password Requests to Wall Directory Watch. [[0;32m OK [0m] Started [0;1;39msystemd-ask-passwo… Requests to Wall Directory Watch. <30>[ 20.438608] systemd[1]: proc-sys-fs-binfmt_misc.automount - Arbitrary Executable File Formats File System Automount Point was skipped because of an unmet condition check (ConditionPathExists=/proc/sys/fs/binfmt_misc). <30>[ 20.452664] systemd[1]: Expecting device dev-ttyAML0.device - /dev/ttyAML0... Expecting device [0;1;39mdev-ttyAML0.device[0m - /dev/ttyAML0... <30>[ 20.474522] systemd[1]: Reached target cryptsetup.target - Local Encrypted Volumes. [[0;32m OK [0m] Reached target [0;1;39mcryptsetup.…get[0m - Local Encrypted Volumes. <30>[ 20.498546] systemd[1]: Reached target integritysetup.target - Local Integrity Protected Volumes. [[0;32m OK [0m] Reached target [0;1;39mintegrityse…Local Integrity Protected Volumes. <30>[ 20.518567] systemd[1]: Reached target paths.target - Path Units. [[0;32m OK [0m] Reached target [0;1;39mpaths.target[0m - Path Units. <30>[ 20.534529] systemd[1]: Reached target remote-fs.target - Remote File Systems. [[0;32m OK [0m] Reached target [0;1;39mremote-fs.target[0m - Remote File Systems. <30>[ 20.550525] systemd[1]: Reached target slices.target - Slice Units. [[0;32m OK [0m] Reached target [0;1;39mslices.target[0m - Slice Units. <30>[ 20.566545] systemd[1]: Reached target swap.target - Swaps. [[0;32m OK [0m] Reached target [0;1;39mswap.target[0m - Swaps. <30>[ 20.582558] systemd[1]: Reached target veritysetup.target - Local Verity Protected Volumes. [[0;32m OK [0m] Reached target [0;1;39mveritysetup… - Local Verity Protected Volumes. <30>[ 20.606722] systemd[1]: Listening on systemd-initctl.socket - initctl Compatibility Named Pipe. [[0;32m OK [0m] Listening on [0;1;39msystemd-initc… initctl Compatibility Named Pipe. <30>[ 20.627948] systemd[1]: Listening on systemd-journald-audit.socket - Journal Audit Socket. [[0;32m OK [0m] Listening on [0;1;39msystemd-journ…socket[0m - Journal Audit Socket. <30>[ 20.648024] systemd[1]: Listening on systemd-journald-dev-log.socket - Journal Socket (/dev/log). [[0;32m OK [0m] Listening on [0;1;39msystemd-journ…t[0m - Journal Socket (/dev/log). <30>[ 20.667341] systemd[1]: Listening on systemd-journald.socket - Journal Socket. [[0;32m OK [0m] Listening on [0;1;39msystemd-journald.socket[0m - Journal Socket. <30>[ 20.692162] systemd[1]: Listening on systemd-networkd.socket - Network Service Netlink Socket. [[0;32m OK [0m] Listening on [0;1;39msystemd-netwo… - Network Service Netlink Socket. <30>[ 20.713270] systemd[1]: Listening on systemd-udevd-control.socket - udev Control Socket. [[0;32m OK [0m] Listening on [0;1;39msystemd-udevd….socket[0m - udev Control Socket. <30>[ 20.731173] systemd[1]: Listening on systemd-udevd-kernel.socket - udev Kernel Socket. [[0;32m OK [0m] Listening on [0;1;39msystemd-udevd…l.socket[0m - udev Kernel Socket. <30>[ 20.794741] systemd[1]: Mounting dev-hugepages.mount - Huge Pages File System... Mounting [0;1;39mdev-hugepages.mount[0m - Huge Pages File System... <30>[ 20.816178] systemd[1]: Mounting dev-mqueue.mount - POSIX Message Queue File System... Mounting [0;1;39mdev-mqueue.mount…POSIX Message Queue File System... <30>[ 20.837032] systemd[1]: Mounting sys-kernel-debug.mount - Kernel Debug File System... Mounting [0;1;39msys-kernel-debug.…[0m - Kernel Debug File System... <30>[ 20.858856] systemd[1]: sys-kernel-tracing.mount - Kernel Trace File System was skipped because of an unmet condition check (ConditionPathExists=/sys/kernel/tracing). <30>[ 20.871962] systemd[1]: Starting kmod-static-nodes.service - Create List of Static Device Nodes... Starting [0;1;39mkmod-static-nodes…ate List of Static Device Nodes... <30>[ 20.897325] systemd[1]: Starting modprobe@configfs.service - Load Kernel Module configfs... Starting [0;1;39mmodprobe@configfs…m - Load Kernel Module configfs... <30>[ 20.921322] systemd[1]: Starting modprobe@dm_mod.service - Load Kernel Module dm_mod... Starting [0;1;39mmodprobe@dm_mod.s…[0m - Load Kernel Module dm_mod... <6>[ 20.942782] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@lists.linux.dev <30>[ 20.945064] systemd[1]: Starting modprobe@drm.service - Load Kernel Module drm... Starting [0;1;39mmodprobe@drm.service[0m - Load Kernel Module drm... <30>[ 20.973106] systemd[1]: Starting modprobe@efi_pstore.service - Load Kernel Module efi_pstore... Starting [0;1;39mmodprobe@efi_psto…- Load Kernel Module efi_pstore... <30>[ 20.995668] systemd[1]: Starting modprobe@fuse.service - Load Kernel Module fuse... Starting [0;1;39mmodprobe@fuse.ser…e[0m - Load Kernel Module fuse... <6>[ 21.020466] fuse: init (API version 7.41) <30>[ 21.023900] systemd[1]: Starting modprobe@loop.service - Load Kernel Module loop... Starting [0;1;39mmodprobe@loop.ser…e[0m - Load Kernel Module loop... <30>[ 21.051038] systemd[1]: Starting systemd-journald.service - Journal Service... Starting [0;1;39msystemd-journald.service[0m - Journal Service... <30>[ 21.078656] systemd[1]: Starting systemd-modules-load.service - Load Kernel Modules... Starting [0;1;39msystemd-modules-l…rvice[0m - Load Kernel Modules... <30>[ 21.100693] systemd[1]: Starting systemd-network-generator.service - Generate network units from Kernel command line... Starting [0;1;39msystemd-network-g… units from Kernel command line... <30>[ 21.158809] systemd[1]: Starting systemd-remount-fs.service - Remount Root and Kernel File Systems... Starting [0;1;39msystemd-remount-f…nt Root and Kernel File Systems... <30>[ 21.180831] systemd[1]: Starting systemd-udev-trigger.service - Coldplug All udev Devices... Starting [0;1;39msystemd-udev-trig…[0m - Coldplug All udev Devices... <30>[ 21.210729] systemd[1]: Started systemd-journald.service - Journal Service. [[0;32m OK [0m] Started [0;1;39msystemd-journald.service[0m - Journal Service. [[0;32m OK [0m] Mounted [0;1;39mdev-hugepages.mount[0m - Huge Pages File System. [[0;32m OK [0m] Mounted [0;1;39mdev-mqueue.mount[…- POSIX Message Queue File System. [[0;32m OK [0m] Mounted [0;1;39msys-kernel-debug.m…nt[0m - Kernel Debug File System. [[0;32m OK [0m] Finished [0;1;39mkmod-static-nodes…reate List of Static Device Nodes. [[0;32m OK [0m] Finished [0;1;39mmodprobe@configfs…[0m - Load Kernel Module configfs. [[0;32m OK [0m] Finished [0;1;39mmodprobe@dm_mod.s…e[0m - Load Kernel Module dm_mod. [[0;32m OK [0m] Finished [0;1;39mmodprobe@drm.service[0m - Load Kernel Module drm. [[0;32m OK [0m] Finished [0;1;39mmodprobe@efi_psto…m - Load Kernel Module efi_pstore. [[0;32m OK [0m] Finished [0;1;39mmodprobe@fuse.service[0m - Load Kernel Module fuse. [[0;32m OK [0m] Finished [0;1;39mmodprobe@loop.service[0m - Load Kernel Module loop. [[0;32m OK [0m] Finished [0;1;39msystemd-modules-l…service[0m - Load Kernel Modules. [[0;32m OK [0m] Finished [0;1;39msystemd-network-g…rk units from Kernel command line. [[0;32m OK [0m] Finished [0;1;39msystemd-remount-f…ount Root and Kernel File Systems. [[0;32m OK [0m] Reached target [0;1;39mnetwork-pre…get[0m - Preparation for Network. Mounting [0;1;39msys-fs-fuse-conne…[0m - FUSE Control File System... Mounting [0;1;39msys-kernel-config…ernel Configuration File System... Starting [0;1;39msystemd-journal-f…h Journal to Persistent Storage... Starting [0;1;39msystemd-random-se…ice[0m - Load/Save Random Seed... <46>[ 21.538523] systemd-journald[231]: Received client request to flush runtime journal. Starting [0;1;39msystemd-sysctl.se…ce[0m - Apply Kernel Variables... Starting [0;1;39msystemd-sysusers.…rvice[0m - Create System Users... [[0;32m OK [0m] Finished [0;1;39msystemd-udev-trig…e[0m - Coldplug All udev Devices. [[0;32m OK [0m] Mounted [0;1;39msys-fs-fuse-connec…nt[0m - FUSE Control File System. [[0;32m OK [0m] Mounted [0;1;39msys-kernel-config.… Kernel Configuration File System. [[0;32m OK [0m] Finished [0;1;39msystemd-random-se…rvice[0m - Load/Save Random Seed. [[0;32m OK [0m] Finished [0;1;39msystemd-sysctl.service[0m - Apply Kernel Variables. [[0;32m OK [0m] Finished [0;1;39msystemd-sysusers.service[0m - Create System Users. Starting [0;1;39msystemd-tmpfiles-…ate Static Device Nodes in /dev... [[0;32m OK [0m] Finished [0;1;39msystemd-journal-f…ush Journal to Persistent Storage. [[0;32m OK [0m] Finished [0;1;39msystemd-tmpfiles-…reate Static Device Nodes in /dev. [[0;32m OK [0m] Reached target [0;1;39mlocal-fs-pr…reparation for Local File Systems. [[0;32m OK [0m] Reached target [0;1;39mlocal-fs.target[0m - Local File Systems. Starting [0;1;39msystemd-tmpfiles-… Volatile Files and Directories... Starting [0;1;39msystemd-udevd.ser…ger for Device Events and Files... [[0;32m OK [0m] Started [0;1;39msystemd-udevd.serv…nager for Device Events and Files. Starting [0;1;39msystemd-networkd.…ice[0m - Network Configuration... [[0;32m OK [0m] Found device [0;1;39mdev-ttyAML0.device[0m - /dev/ttyAML0. [[0;32m OK [0m] Finished [0;1;39msystemd-tmpfiles-…te Volatile Files and Directories. Starting [0;1;39msystemd-timesyncd… - Network Time Synchronization... Starting [0;1;39msystemd-update-ut…rd System Boot/Shutdown in UTMP... <5>[ 22.367889] cfg80211: Loading compiled-in X.509 certificates for regulatory database <5>[ 22.406820] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [<5>[ 22.407513] Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600' <4>[ 22.415556] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 <6>[ 22.423614] cfg80211: failed to load regulatory.db [0;32m OK [0m] Finished [0;1;39msystemd-update-ut…cord System Boot/Shutdown in UTMP. [[0;32m OK [0m] Started [0;1;39msystemd-networkd.service[0m - Network Configuration. [[0;32m OK [0m] Reached target [0;1;39mnetwork.target[0m - Network. [[0;32m OK [0m] Started [0;1;39msystemd-timesyncd.…0m - Network Time Synchronization. [[0;32m OK [0m] Reached target [0;1;39msysinit.target[0m - System Initialization. [[0;32m OK [0m] Started [0;1;39msystemd-tmpfiles-c… Cleanup of Temporary Directories. [[0;32m OK [0m] Reached target [0;1;39mtime-set.target[0m - System Time Set. <46>[ 22.564808] systemd-journald[231]: Oldest entry in /var/log/journal/44a983756b26438995e691b947c527e4/system.journal is older than the configured file retention duration (1month), suggesting rotation. <46>[ 22.578766] systemd-journald[231]: /var/log/journal/44a983756b26438995e691b947c527e4/system.journal: Journal header limits reached or header out-of-date, rotating. [[0;32m OK [0m] Started [0;1;39mapt-daily.timer[0m - Daily apt download activities. [[0;32m OK [0m] Started [0;1;39mapt-daily-upgrade.… apt upgrade and clean activities. [[0;32m OK [0m] Started [0;1;39mdpkg-db-backup.tim… Daily dpkg database backup timer. [[0;32m OK [0m] Started [0;1;39me2scrub_all.timer…etadata Check for All Filesystems. [[0;32m OK [0m] Started [0;1;39mfstrim.timer[0m - Discard unused blocks once a week. [[0;32m OK [0m] Reached target [0;1;39mtimers.target[0m - Timer Units. [[0;32m OK [0m] Listening on [0;1;39mdbus.socket[…- D-Bus System Message Bus Socket. [[0;32m OK [0m] Reached target [0;1;39msockets.target[0m - Socket Units. [[0;32m OK [0m] Reached target [0;1;39mbasic.target[0m - Basic System. Starting [0;1;39mdbus.service[0m - D-Bus System Message Bus... Starting [0;1;39me2scrub_reap.serv…e ext4 Metadata Check Snapshots... Starting [0;1;39msystemd-logind.se…ice[0m - User Login Management... Starting [0;1;39msystemd-user-sess…vice[0m - Permit User Sessions... [[0;32m OK [0m] Finished [0;1;39msystemd-user-sess…ervice[0m - Permit User Sessions. [[0;32m OK [0m] Reached target [0;1;39musb-gadget.…m - Hardware activated USB gadget. [[0;32m OK [0m] Listening on [0;1;39msystemd-rfkil…l Switch Status /dev/rfkill Watch. Starting [0;1;39malsa-restore.serv…- Save/Restore Sound Card State... [[0;32m OK [0m] Started [0;1;39mgetty@tty1.service[0m - Getty on tty1. [[0;32m OK [0m] Started [0;1;39mserial-getty@ttyAM…ice[0m - Serial Getty on ttyAML0. [[0;32m OK [0m] Reached target [0;1;39mgetty.target[0m - Login Prompts. [[0;32m OK [0m] Started [0;1;39mdbus.service[0m - D-Bus System Message Bus. [[0;32m OK [0m] Finished [0;1;39me2scrub_reap.serv…ine ext4 Metadata Check Snapshots. [[0;32m OK [0m] Finished [0;1;39malsa-restore.serv…m - Save/Restore Sound Card State. [[0;32m OK [0m] Reached target [0;1;39msound.target[0m - Sound Card. [[0;32m OK [0m] Started [0;1;39msystemd-logind.service[0m - User Login Management. [[0;32m OK [0m] Reached target [0;1;39mmulti-user.target[0m - Multi-User System. [[0;32m OK [0m] Reached target [0;1;39mgraphical.target[0m - Graphical Interface. Starting [0;1;39msystemd-update-ut… Record Runlevel Change in UTMP... [[0;32m OK [0m] Finished [0;1;39msystemd-update-ut… - Record Runlevel Change in UTMP. Debian GNU/Linux 12 debian-bookworm-arm64 ttyAML0 debian-bookworm-arm64 login: root (automatic login) Linux debian-bookworm-arm64 6.12.0-rc2 #1 SMP PREEMPT Fri Nov 8 00:30:12 UTC 2024 aarch64 The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # <4>[ 24.258452] rc rc0: nonsensical timing event of duration 0 / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/956817/extract-nfsrootfs-uzrwqge2' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/956817/extract-nfsrootfs-uzrwqge2' / # export NFS_SERVER_IP='192.168.6.2' export NFS_SERVER_IP='192.168.6.2' / # # # / # export SHELL=/bin/bash export SHELL=/bin/bash / # . /lava-956817/environment . /lava-956817/environment / # /lava-956817/bin/lava-test-runner /lava-956817/0 /lava-956817/bin/lava-test-runner /lava-956817/0 + export TESTRUN_ID=0_timesync-off + TESTRUN_ID=0_timesync-off + cd /lava-956817/0/tests/0_timesync-off ++ cat uuid + UUID=956817_1.6.2.4.1 + set +x + systemctl stop systemd-timesyncd + set +x + export TESTRUN_ID=1_kselftest-rtc + TESTRUN_ID=1_kselftest-rtc + cd /lava-956817/0/tests/1_kselftest-rtc ++ cat uuid + UUID=956817_1.6.2.4.5 + set +x + cd ./automated/linux/kselftest/ + ./kselftest.sh -c rtc -T '' -t kselftest_armhf.tar.gz -s True -u http://storage.kernelci.org/broonie-sound/for-next/asoc-fix-v6.12-rc6-244-g80b3d72150d5/arm64/defconfig/gcc-12/kselftest.tar.xz -L '' -S /dev/null -b meson-g12b-a311d-libretech-cc -g broonie-sound -e '' -p /opt/kselftests/mainline/ -n 1 -i 1 -E '' INFO: install_deps skipped --2024-11-08 02:29:31-- http://storage.kernelci.org/broonie-sound/for-next/asoc-fix-v6.12-rc6-244-g80b3d72150d5/arm64/defconfig/gcc-12/kselftest.tar.xz Resolving storage.kernelci.org (storage.kernelci.org)... 20.171.243.82 Connecting to storage.kernelci.org (storage.kernelci.org)|20.171.243.82|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 6923632 (6.6M) [application/octet-stream] Saving to: 'kselftest_armhf.tar.gz' kselftest_armhf.tar 0%[ ] 0 --.-KB/s kselftest_armhf.tar 0%[ ] 49.92K 174KB/s kselftest_armhf.tar 3%[ ] 218.67K 383KB/s kselftest_armhf.tar 13%[=> ] 893.67K 1.02MB/s kselftest_armhf.tar 53%[=========> ] 3.51M 3.07MB/s kselftest_armhf.tar 100%[===================>] 6.60M 5.04MB/s in 1.3s 2024-11-08 02:29:33 (5.04 MB/s) - 'kselftest_armhf.tar.gz' saved [6923632/6923632] skiplist: ======================================== ======================================== rtc:rtctest ============== Tests to run =============== rtc:rtctest ===========End Tests to run =============== shardfile-rtc pass <12>[ 43.906655] kselftest: Running tests in rtc TAP version 13 1..1 # timeout set to 210 # selftests: rtc: rtctest # TAP version 13 # 1..8 # # Starting 8 tests from 1 test cases. # # RUN rtc.date_read ... # # rtctest.c:52:date_read:Current RTC date/time is 08/11/2024 02:29:43. # # OK rtc.date_read # ok 1 rtc.date_read # # RUN rtc.date_read_loop ... # # rtctest.c:95:date_read_loop:Continuously reading RTC time for 30s (with 11ms breaks after every read). # # rtctest.c:122:date_read_loop:Performed 2763 RTC time reads. # # OK rtc.date_read_loop # ok 2 rtc.date_read_loop # # RUN rtc.uie_read ... # # uie_read: Test terminated by timeout # # FAIL rtc.uie_read # not ok 3 rtc.uie_read # # RUN rtc.uie_select ... # # rtctest.c:179:uie_select:Expected 0 (0) != rc (0) # # uie_select: Test terminated by assertion # # FAIL rtc.uie_select # not ok 4 rtc.uie_select # # RUN rtc.alarm_alm_set ... # # rtctest.c:221:alarm_alm_set:Alarm time now set to 02:30:24. # # rtctest.c:233:alarm_alm_set:Expected 0 (0) != rc (0) # # alarm_alm_set: Test terminated by assertion # # FAIL rtc.alarm_alm_set # not ok 5 rtc.alarm_alm_set # # RUN rtc.alarm_wkalm_set ... # # rtctest.c:281:alarm_wkalm_set:Alarm time now set to 08/11/2024 02:30:29. # # rtctest.c:291:alarm_wkalm_set:Expected 0 (0) != rc (0) # # alarm_wkalm_set: Test terminated by assertion # # FAIL rtc.alarm_wkalm_set # not ok 6 rtc.alarm_wkalm_set # # RUN rtc.alarm_alm_set_minute ... # # rtctest.c:331:alarm_alm_set_minute:Alarm time now set to 02:31:00. # # rtctest.c:343:alarm_alm_set_minute:Expected 0 (0) != rc (0) # # alarm_alm_set_minute: Test terminated by assertion # # FAIL rtc.alarm_alm_set_minute # not ok 7 rtc.alarm_alm_set_minute # # RUN rtc.alarm_wkalm_set_minute ... # # rtctest.c:391:alarm_wkalm_set_minute:Alarm time now set to 08/11/2024 02:32:00. # # rtctest.c:401:alarm_wkalm_set_minute:Expected 0 (0) != rc (0) # # alarm_wkalm_set_minute: Test terminated by assertion # # FAIL rtc.alarm_wkalm_set_minute # not ok 8 rtc.alarm_wkalm_set_minute # # FAILED: 2 / 8 tests passed. # # Totals: pass:2 fail:6 xfail:0 xpass:0 skip:0 error:0 not ok 1 selftests: rtc: rtctest # exit=1 rtc_rtctest_rtc_date_read pass rtc_rtctest_rtc_date_read_loop pass rtc_rtctest_rtc_uie_read fail rtc_rtctest_rtc_uie_select fail rtc_rtctest_rtc_alarm_alm_set fail rtc_rtctest_rtc_alarm_wkalm_set fail rtc_rtctest_rtc_alarm_alm_set_minute fail rtc_rtctest_rtc_alarm_wkalm_set_minute fail rtc_rtctest fail + ../../utils/send-to-lava.sh ./output/result.txt + set +x / #