connecting to NetworkSerialPort(target=Target(name='imx53-qsrb-0', env=None), name='NetworkSerialPort', state=, avail=True, host='moxa.cuskci.stw.pengutronix.de', port=4010, speed=115200, protocol='rfc2217') calling microcom -s 115200 -t moxa.cuskci.stw.pengutronix.de:4010 connected to 10.8.254.5 (port 4010) Escape character: Ctrl-\ Type the escape character to get to the prompt. barebox 2023.01.0 #1 Fri Jan 27 16:21:21 CET 2023 Board: Freescale i.MX53 Quick Start-R Board detected i.MX53 revision 2.1 mc13xxx-i2c mc347080: Found MC34708 ID: 0x014 mdio_bus: miibus0: probed eth0: got preset MAC address: 00:04:9f:02:71:b3 imx-usb 53f80200.usb@53f80200.of: USB EHCI 1.00 imx-esdhc 50004000.mmc@50004000.of: registered as mmc0 imx-esdhc 50020000.mmc@50020000.of: registered as mmc2 imx-ipuv3 18000000.ipu@18000000.of: IPUv3M probed netconsole: registered as netconsole-1 malloc space: 0xbfe7d3c0 -> 0xcfcfa77f (size 254.5 MiB) mmc0: detected SD card version 2.0 mmc0: registered mmc0 MCIMX53-START-R board 1.0 rev B envfs: no envfs (magic mismatch) - envfs never written? [?25h Hit m for menu or any to stop autoboot: 3 [1;32mbarebox@[1;36mFreescale i.MX53 Quick Start-R Board:/[0m bootm -v -r /mnt/tftp/899138/tftp-deploy-93859jbh/ramdisk/ramdisk.cpio.gz -o /mnt/tftp/899138/tftp-deploy-93859jbh/dtb/imx53-qsrb.dtb /mnt/tftp/899138/tftp-deploy-93859jbh/kernel/zImage [1;32mbarebox@[1;36mFreescale i.MX53 Quick Start-R Board:/[0m bootm -v -r /mnt/tftp/899138/tftp-deploy-93859jbh/ramdisk/ramdisk.cpio.gz -o /mnt/tftp/899138/tftp-deploy-93859jbh/dtb/imx53-qsrb.dtb /mnt/tftp/899138/tftp-deploy-93859jbh/kernel/zImage eth0: 100Mbps full duplex link detected T eth0: DHCP client bound to address 10.8.254.89 Loading ARM Linux zImage '/mnt/tftp/899138/tftp-deploy-93859jbh/kernel/zImage' OS image not yet relocated Passing control to ARM zImage handler no OS load address, defaulting to 0x729a0000 no initrd load address, defaulting to 0x78000000 Loaded initrd GZIP compressed '/mnt/tftp/899138/tftp-deploy-93859jbh/ramdisk/ramdisk.cpio.gz' initrd is at 0x78000000-0x78cb6fd5 Loading devicetree from '/mnt/tftp/899138/tftp-deploy-93859jbh/dtb/imx53-qsrb.dtb' commandline: console=ttymxc0,115200n8 Starting kernel at 0x729a0000, initrd at 0x78000000, oftree at 0x78cb7000... Starting kernel in secure mode [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.272-cip90 (KernelCI@build-j989987-arm-gcc-10-multi-v7-defconfig-nbbqq) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Mon Feb 6 11:06:20 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc085] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX53 Quick Start-R Board [ 0.000000] Memory policy: Data cache writeback [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0xcb800000 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] percpu: Embedded 16 pages/cpu s36748 r8192 d20596 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 261120 [ 0.000000] Kernel command line: console=ttymxc0,115200n8 [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 938664K/1048576K available (12288K kernel code, 1597K rwdata, 4684K rodata, 2048K init, 394K bss, 44376K reserved, 65536K cma-reserved, 457624K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) [ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) [ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1598 kB) [ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 395 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] TrustZone Interrupt Controller (TZIC) initialized [ 0.000000] CPU identified as i.MX53, silicon rev 2.1 [ 0.000000] Switching to timer-based delay loop, resolution 25ns [ 0.000008] sched_clock: 32 bits at 40MHz, resolution 25ns, wraps every 53687091187ns [ 0.000026] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 47781511156 ns [ 0.001929] Console: colour dummy device 80x30 [ 0.001995] Calibrating delay loop (skipped), value calculated using timer frequency.. 80.00 BogoMIPS (lpj=400000) [ 0.002013] pid_max: default: 32768 minimum: 301 [ 0.002168] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.002184] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.002922] CPU: Testing write buffer coherency: ok [ 0.002971] CPU0: Spectre v2: using BPIALL workaround [ 0.003407] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.004206] Setting up static identity map for 0x70300000 - 0x703000a0 [ 0.005285] rcu: Hierarchical SRCU implementation. [ 0.007211] EFI services will not be available. [ 0.007415] smp: Bringing up secondary CPUs ... [ 0.007428] smp: Brought up 1 node, 1 CPU [ 0.007439] SMP: Total of 1 processors activated (80.00 BogoMIPS). [ 0.007447] CPU: All CPU(s) started in SVC mode. [ 0.009217] devtmpfs: initialized [ 0.017105] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2 [ 0.017584] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.017615] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.021604] pinctrl core: initialized pinctrl subsystem [ 0.023409] DMI not present or invalid. [ 0.024250] NET: Registered protocol family 16 [ 0.026976] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.031893] cpuidle: using governor menu [ 0.032370] No ATAGs? [ 0.032378] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.034459] Serial: AMBA PL011 UART driver [ 0.043002] imx53-pinctrl 53fa8000.iomuxc: Failed to create dummy-iomuxc-gpr@53fa8000 debugfs directory [ 0.043305] imx53-pinctrl 53fa8000.iomuxc: initialized IMX pinctrl driver [ 0.079790] vgaarb: loaded [ 0.080862] SCSI subsystem initialized [ 0.081654] usbcore: registered new interface driver usbfs [ 0.081715] usbcore: registered new interface driver hub [ 0.081778] usbcore: registered new device driver usb [ 0.083194] i2c i2c-1: IMX I2C adapter registered [ 0.083221] i2c i2c-1: can't use DMA, using PIO instead. [ 0.083996] i2c i2c-0: IMX I2C adapter registered [ 0.084017] i2c i2c-0: can't use DMA, using PIO instead. [ 0.085147] pps_core: LinuxPPS API ver. 1 registered [ 0.085158] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.085185] PTP clock support registered [ 0.085400] EDAC MC: Ver: 3.0.0 [ 0.088566] clocksource: Switched to clocksource mxc_timer1 [ 0.159550] NET: Registered protocol family 2 [ 0.159879] IP idents hash table entries: 8192 (order: 4, 65536 bytes) [ 0.160533] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) [ 0.160575] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.160619] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.160681] TCP: Hash tables configured (established 4096 bind 4096) [ 0.160845] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.160873] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.161042] NET: Registered protocol family 1 [ 0.161798] RPC: Registered named UNIX socket transport module. [ 0.161813] RPC: Registered udp transport module. [ 0.161820] RPC: Registered tcp transport module. [ 0.161827] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.162391] Trying to unpack rootfs image as initramfs... [ 1.112417] Freeing initrd memory: 13020K [ 1.113234] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available [ 1.115141] Initialise system trusted keyrings [ 1.115539] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 1.123087] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.124252] NFS: Registering the id_resolver key type [ 1.124347] Key type id_resolver registered [ 1.124356] Key type id_legacy registered [ 1.124407] ntfs: driver 2.1.32 [Flags: R/O]. [ 1.126936] Key type asymmetric registered [ 1.126953] Asymmetric key parser 'x509' registered [ 1.127021] bounce: pool size: 64 pages [ 1.127084] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 1.127097] io scheduler noop registered [ 1.127105] io scheduler deadline registered [ 1.127298] io scheduler cfq registered (default) [ 1.127310] io scheduler mq-deadline registered [ 1.127317] io scheduler kyber registered [ 1.155905] imx-sdma 63fb0000.sdma: Direct firmware load for imx/sdma/sdma-imx53.bin failed with error -2 [ 1.155936] imx-sdma 63fb0000.sdma: external firmware not found, using ROM firmware [ 1.210864] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.214566] SuperH (H)SCI(F) driver initialized [ 1.215393] 53fbc000.serial: ttymxc0 at MMIO 0x53fbc000 (irq = 47, base_baud = 4166666) is a IMX [ 1.896720] console [ttymxc0] enabled [ 1.901772] msm_serial: driver initialized [ 1.906060] STMicroelectronics ASC driver initialized [ 1.912507] STM32 USART driver initialized [ 1.934896] brd: module loaded [ 1.946887] loop: module loaded [ 1.953238] ahci-imx 10000000.sata: hwmon0: sensor 'sata_ahci' [ 1.961343] ahci-imx 10000000.sata: SSS flag set, parallel bus scan disabled [ 1.968428] ahci-imx 10000000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 1.977387] ahci-imx 10000000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc [ 1.987540] scsi host0: ahci-imx [ 1.991426] ata1: SATA max UDMA/133 mmio [mem 0x10000000-0x10000fff] port 0x100 irq 44 [ 2.008196] CAN device driver interface [ 2.013209] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 2.020103] fec 63fec000.ethernet: 63fec000.ethernet supply phy not found, using dummy regulator [ 2.029073] fec 63fec000.ethernet: Linked as a consumer to regulator.0 [ 2.066150] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 2.072158] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 2.078185] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 2.085188] igb: Copyright (c) 2007-2014 Intel Corporation. [ 2.094750] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 2.102297] usbcore: registered new interface driver pegasus [ 2.108017] usbcore: registered new interface driver asix [ 2.113494] usbcore: registered new interface driver ax88179_178a [ 2.119651] usbcore: registered new interface driver cdc_ether [ 2.125530] usbcore: registered new interface driver smsc75xx [ 2.131348] usbcore: registered new interface driver smsc95xx [ 2.137131] usbcore: registered new interface driver net1080 [ 2.142854] usbcore: registered new interface driver cdc_subset [ 2.148830] usbcore: registered new interface driver zaurus [ 2.154500] usbcore: registered new interface driver cdc_ncm [ 2.162393] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.168995] ehci-pci: EHCI PCI platform driver [ 2.173506] ehci-platform: EHCI generic platform driver [ 2.179003] ehci-orion: EHCI orion driver [ 2.183185] SPEAr-ehci: EHCI SPEAr driver [ 2.187326] ehci-st: EHCI STMicroelectronics driver [ 2.192394] ehci-exynos: EHCI EXYNOS driver [ 2.196715] ehci-atmel: EHCI Atmel driver [ 2.200908] tegra-ehci: Tegra EHCI driver [ 2.205069] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.211319] ohci-pci: OHCI PCI platform driver [ 2.215831] ohci-platform: OHCI generic platform driver [ 2.221298] SPEAr-ohci: OHCI SPEAr driver [ 2.225471] ohci-st: OHCI STMicroelectronics driver [ 2.230537] ohci-atmel: OHCI Atmel driver [ 2.235281] usbcore: registered new interface driver usb-storage [ 2.247364] i2c /dev entries driver [ 2.262298] imx2-wdt 53f98000.wdog: timeout 60 sec (nowayout=0) [ 2.274362] sdhci: Secure Digital Host Controller Interface driver [ 2.280678] sdhci: Copyright(c) Pierre Ossman [ 2.286680] Synopsys Designware Multimedia Card Interface Driver [ 2.294221] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.326724] mmc0: SDHCI controller on 50004000.esdhc [50004000.esdhc] using ADMA [ 2.337714] sdhci-esdhc-imx 50020000.esdhc: Got CD GPIO [ 2.343338] sdhci-esdhc-imx 50020000.esdhc: Got WP GPIO [ 2.360356] ata1: SATA link down (SStatus 0 SControl 300) [ 2.365914] ahci-imx 10000000.sata: no device found, disabling link. [ 2.372357] ahci-imx 10000000.sata: pass ahci_imx..hotplug=1 to enable hotplug [ 2.393659] mmc1: SDHCI controller on 50020000.esdhc [50020000.esdhc] using ADMA [ 2.405279] ledtrig-cpu: registered to indicate activity on CPUs [ 2.412294] usbcore: registered new interface driver usbhid [ 2.417874] usbhid: USB HID core driver [ 2.426682] NET: Registered protocol family 10 [ 2.434731] Segment Routing with IPv6 [ 2.438497] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.445443] NET: Registered protocol family 17 [ 2.449997] can: controller area network core (rev 20170425 abi 9) [ 2.456288] NET: Registered protocol family 29 [ 2.460779] can: raw protocol (rev 20170425) [ 2.465058] can: broadcast manager protocol (rev 20170425 t) [ 2.470760] can: netlink gateway (rev 20170425) max_hops=1 [ 2.477047] Key type dns_resolver registered [ 2.481989] ThumbEE CPU extension supported. [ 2.486289] Registering SWP/SWPB emulation handler [ 2.493944] Loading compiled-in X.509 certificates [ 2.522226] mmc0: host does not support reading read-only switch, assuming write-enable [ 2.537884] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 2.546333] mmc0: new high speed SDHC card at address 0001 [ 2.552652] hctosys: unable to open rtc device (rtc0) [ 2.566139] mmcblk0: mmc0:0001 SD16G 14.6 GiB [ 2.574642] Freeing unused kernel memory: 2048K [ 2.580733] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: [ 2.804060] udevd[84]: starting version 3.2.9 [ 2.810646] random: udevd: uninitialized urandom read (16 bytes read) [ 2.817482] random: udevd: uninitialized urandom read (16 bytes read) [ 2.824649] random: udevd: uninitialized urandom read (16 bytes read) [ 2.841476] udevd[84]: specified user 'tss' unknown [ 2.846571] udevd[84]: specified group 'tss' unknown [ 2.856951] udevd[85]: starting eudev-3.2.9 [ 4.325217] usb_phy_generic usbphy-0: usbphy-0 supply vcc not found, using dummy regulator [ 4.333803] usb_phy_generic usbphy-0: Linked as a consumer to regulator.0 [ 4.340892] usb_phy_generic usbphy-1: usbphy-1 supply vcc not found, using dummy regulator [ 4.349299] usb_phy_generic usbphy-1: Linked as a consumer to regulator.0 [ 4.401896] imx_usb 53f80200.usb: Linked as a consumer to regulator.2 [ 4.452693] sgtl5000 1-000a: Linked as a consumer to regulator.1 [ 4.463460] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 4.468430] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 [ 4.507188] sgtl5000 1-000a: sgtl5000 revision 0x11 [ 4.534181] sgtl5000 1-000a: Using internal LDO instead of VDDD: check ER1 erratum [ 4.548909] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 4.568679] hub 1-0:1.0: USB hub found [ 4.572593] hub 1-0:1.0: 1 port detected done Saving random seed: [ 5.491022] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: OK Starting dropbear sshd: [ 5.621964] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-899138/environment . /lava-899138/environment / # /lava-899138/bin/lava-test-runner /lava-899138/0 /lava-899138/bin/lava-test-runner /lava-899138/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-899138/0/tests/0_dmesg + cat uuid + UUID=899138_1.5.2.3.1 [ 6.245249] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh [ 6.305740] [ 6.360451] [ 6.415106] + set +x[ 6.425799] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-899138/environment / # . /lava-899138/environment/lava-899138/bin/lava-test-runner /lava-899138/1 / # /lava-899138/bin/lava-test-runner /lava-899138/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-899138/1/tests/1_bootrr + cat uuid + UUID=899138_1.5.2.3.5 [ 6.954954] + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-899138/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto /lava-899138/1/../bin/lava-test-case [ 7.027268] /lava-899138/1/../bin/lava-test-case [ 7.079606] /lava-899138/1/../bin/lava-test-case [ 7.110684] + set +x[ 7.134777] / #