[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.33 (9 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 9284186/tftp-deploy-4yf2gj01/kernel/zImage tftp 0x10000000 9284186/tftp-deploy-4yf2gj01/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.33 Filename '9284186/tftp-deploy-4yf2gj01/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 5.6 MiB/s done Bytes transferred = 8729088 (853200 hex) => tftp 0x14000000 9284186/tftp-deploy-4yf2gj01/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 9284186/tftp-deploy-4yf2gj01/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.33 Filename '9284186/tftp-deploy-4yf2gj01/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################### 11.7 MiB/s done Bytes transferred = 9411557 (8f9be5 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 9284186/tftp-deploy-4yf2gj01/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 9284186/tftp-deploy-4yf2gj01/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.33 Filename '9284186/tftp-deploy-4yf2gj01/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 4 MiB/s done Bytes transferred = 41606 (a286 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/9284186/extract-nfsrootfs-obuj4lhr,tcp,hard ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/9284186/extract-nfsrootfs-obuj4lhr,tcp,hard ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x853200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 9411493 Bytes = 9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d285 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.273-cip91 (KernelCI@build-j1086047-arm-gcc-10-multi-v7-defconfig-g2tj5) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Wed Feb 22 18:47:49 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] percpu: Embedded 16 pages/cpu s36748 r8192 d20596 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/9284186/extract-nfsrootfs-obuj4lhr,tcp,hard ip=dhcp [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 942972K/1048576K available (12288K kernel code, 1597K rwdata, 4684K rodata, 2048K init, 394K bss, 40068K reserved, 65536K cma-reserved, 196608K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) [ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) [ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1598 kB) [ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 395 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] L2C-310 errata 752271 769419 enabled [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 [ 0.000000] Switching to timer-based delay loop, resolution 333ns [ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns [ 0.000024] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns [ 0.003083] Console: colour dummy device 80x30 [ 0.003125] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) [ 0.003140] pid_max: default: 32768 minimum: 301 [ 0.003271] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.003293] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.003827] CPU: Testing write buffer coherency: ok [ 0.003854] CPU0: Spectre v2: using BPIALL workaround [ 0.004213] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.004881] Setting up static identity map for 0x10300000 - 0x103000a0 [ 0.006473] rcu: Hierarchical SRCU implementation. [ 0.009618] EFI services will not be available. [ 0.009921] smp: Bringing up secondary CPUs ... [ 0.010694] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.010700] CPU1: Spectre v2: using BPIALL workaround [ 0.011596] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.011603] CPU2: Spectre v2: using BPIALL workaround [ 0.012458] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.012463] CPU3: Spectre v2: using BPIALL workaround [ 0.012566] smp: Brought up 1 node, 4 CPUs [ 0.012578] SMP: Total of 4 processors activated (24.00 BogoMIPS). [ 0.012586] CPU: All CPU(s) started in SVC mode. [ 0.013647] devtmpfs: initialized [ 0.021013] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.021372] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.021394] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.024565] pinctrl core: initialized pinctrl subsystem [ 0.026164] DMI not present or invalid. [ 0.026989] NET: Registered protocol family 16 [ 0.030452] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.032751] cpuidle: using governor menu [ 0.032930] CPU identified as i.MX6Q, silicon rev 1.2 [ 0.042700] vdd1p1: supplied by regulator-dummy [ 0.043222] vdd3p0: supplied by regulator-dummy [ 0.043708] vdd2p5: supplied by regulator-dummy [ 0.044226] vddarm: supplied by regulator-dummy [ 0.044884] vddpu: supplied by regulator-dummy [ 0.045264] vddsoc: supplied by regulator-dummy [ 0.059399] No ATAGs? [ 0.059536] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.059551] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.062886] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory [ 0.063129] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver [ 0.068167] Serial: AMBA PL011 UART driver [ 0.070487] console [pstore-1] enabled [ 0.070665] pstore: Registered ramoops as persistent store backend [ 0.070679] ramoops: attached 0x10000@0x30000000, ecc: 0/0 [ 0.093142] mxs-dma 110000.dma-apbh: initialized [ 0.100564] vgaarb: loaded [ 0.101380] SCSI subsystem initialized [ 0.101800] usbcore: registered new interface driver usbfs [ 0.101854] usbcore: registered new interface driver hub [ 0.101910] usbcore: registered new device driver usb [ 0.103151] i2c i2c-0: IMX I2C adapter registered [ 0.103173] i2c i2c-0: can't use DMA, using PIO instead. [ 0.103732] i2c i2c-1: IMX I2C adapter registered [ 0.103752] i2c i2c-1: can't use DMA, using PIO instead. [ 0.104167] i2c i2c-2: IMX I2C adapter registered [ 0.104184] i2c i2c-2: can't use DMA, using PIO instead. [ 0.105717] pps_core: LinuxPPS API ver. 1 registered [ 0.105729] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.105752] PTP clock support registered [ 0.105990] EDAC MC: Ver: 3.0.0 [ 0.108727] clocksource: Switched to clocksource mxc_timer1 [ 0.167744] NET: Registered protocol family 2 [ 0.168202] IP idents hash table entries: 16384 (order: 5, 131072 bytes) [ 0.169473] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) [ 0.169516] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.169605] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.169752] TCP: Hash tables configured (established 8192 bind 8192) [ 0.169958] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.170005] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.170171] NET: Registered protocol family 1 [ 0.170683] RPC: Registered named UNIX socket transport module. [ 0.170696] RPC: Registered udp transport module. [ 0.170705] RPC: Registered tcp transport module. [ 0.170715] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.171171] Trying to unpack rootfs image as initramfs... [ 0.886883] Freeing initrd memory: 9192K [ 0.887422] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 0.887801] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 0.889817] Initialise system trusted keyrings [ 0.890112] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 0.896184] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.896830] NFS: Registering the id_resolver key type [ 0.896887] Key type id_resolver registered [ 0.896899] Key type id_legacy registered [ 0.896948] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.899074] Key type asymmetric registered [ 0.899090] Asymmetric key parser 'x509' registered [ 0.899150] bounce: pool size: 64 pages [ 0.899200] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) [ 0.899213] io scheduler noop registered [ 0.899224] io scheduler deadline registered [ 0.899368] io scheduler cfq registered (default) [ 0.899383] io scheduler mq-deadline registered [ 0.899394] io scheduler kyber registered [ 0.920834] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 0.920907] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 0.921058] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 0.921111] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 0.934004] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set [ 0.934087] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc [ 0.934147] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set [ 0.934234] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 [ 0.934450] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 0.934470] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 0.934502] PU : no governor for states [ 0.934522] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc [ 0.988879] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.992453] SuperH (H)SCI(F) driver initialized [ 0.993355] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX [ 0.994134] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX [ 1.901267] console [ttymxc1] enabled [ 1.906141] msm_serial: driver initialized [ 1.910523] STMicroelectronics ASC driver initialized [ 1.917404] STM32 USART driver initialized [ 1.932212] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 1.940650] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 1.947352] panel-simple panel-lcd: Dropping the link to regulator.0 [ 1.953872] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 1.962651] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 1.969550] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 1.984058] brd: module loaded [ 1.996570] loop: module loaded [ 2.002984] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 [ 2.010967] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 [ 2.018995] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 [ 2.027181] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 [ 2.037702] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled [ 2.044726] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 2.053541] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 2.064058] scsi host0: ahci-imx [ 2.067872] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 [ 2.086494] CAN device driver interface [ 2.091614] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 2.098392] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator [ 2.107090] fec 2188000.ethernet: Linked as a consumer to regulator.0 [ 2.115913] pps pps0: new PPS source ptp0 [ 2.137688] fec 2188000.ethernet eth0: registered PHC device 0 [ 2.144850] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 2.150707] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 2.156688] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 2.163669] igb: Copyright (c) 2007-2014 Intel Corporation. [ 2.175067] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 2.182533] usbcore: registered new interface driver pegasus [ 2.188242] usbcore: registered new interface driver asix [ 2.193698] usbcore: registered new interface driver ax88179_178a [ 2.199843] usbcore: registered new interface driver cdc_ether [ 2.205730] usbcore: registered new interface driver smsc75xx [ 2.211543] usbcore: registered new interface driver smsc95xx [ 2.217327] usbcore: registered new interface driver net1080 [ 2.223042] usbcore: registered new interface driver cdc_subset [ 2.229009] usbcore: registered new interface driver zaurus [ 2.234651] usbcore: registered new interface driver cdc_ncm [ 2.243210] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.249775] ehci-pci: EHCI PCI platform driver [ 2.254264] ehci-platform: EHCI generic platform driver [ 2.259807] ehci-orion: EHCI orion driver [ 2.264039] SPEAr-ehci: EHCI SPEAr driver [ 2.268239] ehci-st: EHCI STMicroelectronics driver [ 2.273325] ehci-exynos: EHCI EXYNOS driver [ 2.277701] ehci-atmel: EHCI Atmel driver [ 2.281918] tegra-ehci: Tegra EHCI driver [ 2.286148] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.292367] ohci-pci: OHCI PCI platform driver [ 2.296860] ohci-platform: OHCI generic platform driver [ 2.302379] SPEAr-ohci: OHCI SPEAr driver [ 2.306583] ohci-st: OHCI STMicroelectronics driver [ 2.311675] ohci-atmel: OHCI Atmel driver [ 2.316672] usbcore: registered new interface driver usb-storage [ 2.324955] imx_usb 2184000.usb: Linked as a consumer to regulator.9 [ 2.336705] imx_usb 2184200.usb: Linked as a consumer to regulator.14 [ 2.346603] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 2.351535] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 [ 2.388757] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 2.394831] hub 1-0:1.0: USB hub found [ 2.398627] hub 1-0:1.0: 1 port detected [ 2.400223] ata1: SATA link down (SStatus 0 SControl 300) [ 2.407991] ahci-imx 2200000.sata: no device found, disabling link. [ 2.408834] i2c /dev entries driver [ 2.414290] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug [ 2.432203] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) [ 2.443320] sdhci: Secure Digital Host Controller Interface driver [ 2.449531] sdhci: Copyright(c) Pierre Ossman [ 2.456147] Synopsys Designware Multimedia Card Interface Driver [ 2.464163] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.470721] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO [ 2.475894] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO [ 2.481146] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 [ 2.520727] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA [ 2.528477] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO [ 2.533754] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 [ 2.573366] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA [ 2.584559] ledtrig-cpu: registered to indicate activity on CPUs [ 2.591352] usbcore: registered new interface driver usbhid [ 2.596931] usbhid: USB HID core driver [ 2.606665] NET: Registered protocol family 10 [ 2.612237] Segment Routing with IPv6 [ 2.615982] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.622498] NET: Registered protocol family 17 [ 2.626957] can: controller area network core (rev 20170425 abi 9) [ 2.633253] NET: Registered protocol family 29 [ 2.637707] can: raw protocol (rev 20170425) [ 2.642001] can: broadcast manager protocol (rev 20170425 t) [ 2.647671] can: netlink gateway (rev 20170425) max_hops=1 [ 2.653603] Key type dns_resolver registered [ 2.658917] cpu cpu0: Linked as a consumer to regulator.4 [ 2.664377] cpu cpu0: Linked as a consumer to regulator.5 [ 2.669873] cpu cpu0: Linked as a consumer to regulator.6 [ 2.676070] ThumbEE CPU extension supported. [ 2.680387] Registering SWP/SWPB emulation handler [ 2.686501] Loading compiled-in X.509 certificates [ 2.692822] pstore: Using compression: deflate [ 2.698499] mmc0: new high speed SDHC card at address aaaa [ 2.706411] mmcblk0: mmc0:aaaa SL16G 14.8 GiB [ 2.710485] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 2.717999] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 2.726563] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 2.731794] GPT:Primary header thinks Alt. header is not at the end of the disk. [ 2.733781] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 2.741124] GPT:29296874 != 31116287 [ 2.741129] GPT:Alternate GPT header not at the end of the disk. [ 2.749574] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 2.751608] GPT:29296874 != 31116287 [ 2.757634] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 2.765956] GPT: Use GNU Parted to correct GPT errors. [ 2.769598] panel-simple panel-lcd: Dropping the link to regulator.0 [ 2.776190] mmcblk0: p1 p2 p3 [ 2.782502] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 2.787793] usb 1-1: new high-speed USB device number 2 using ci_hdrc [ 2.790780] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 2.812757] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 2.821200] imx_thermal tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C [ 2.831391] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 2.838490] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 2.846500] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 2.853704] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 2.861946] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 2.870373] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 2.877045] panel-simple panel-lcd: Dropping the link to regulator.0 [ 2.884569] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 2.893327] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 2.900180] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 2.907604] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 2.914720] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 2.922581] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 2.929771] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 2.937927] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 2.946336] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 2.953027] panel-simple panel-lcd: Dropping the link to regulator.0 [ 2.960523] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 2.969283] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 2.976126] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 2.984298] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 [ 2.990936] hctosys: unable to open rtc device (rtc0) [ 2.997147] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 3.004352] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 3.011445] hub 1-1:1.0: USB hub found [ 3.012512] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 3.015333] hub 1-1:1.0: 3 ports detected [ 3.022403] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 3.034735] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 3.043165] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 3.049862] panel-simple panel-lcd: Dropping the link to regulator.0 [ 3.057406] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 3.066172] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 3.073032] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 3.080465] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 3.087553] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 3.095408] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 3.102606] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 3.139676] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) [ 3.154403] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 6.249437] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 6.278845] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 6.308873] Sending DHCP requests ., OK [ 6.352700] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.33 [ 6.360783] IP-Config: Complete: [ 6.364040] device=eth0, hwaddr=00:19:b8:08:f1:13, ipaddr=192.168.201.33, mask=255.255.255.0, gw=192.168.201.1 [ 6.374524] host=imx6q-sabrelite-lava-cbg-3, domain=lava-rack, nis-domain=(none) [ 6.382399] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= [ 6.382408] nameserver0=192.168.201.1 [ 6.400793] Freeing unused kernel memory: 2048K [ 6.419116] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u1 [ 7.211610] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 7.219482] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 [ 7.227371] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) [ 7.228817] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 7.241727] panel-simple panel-lcd: Dropping the link to regulator.0 [ 7.249909] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 7.258797] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 7.259713] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) [ 7.265757] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 7.280085] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 7.287317] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 7.287506] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) [ 7.295727] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 7.307890] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 7.308279] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) [ 7.317199] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 7.321409] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 [ 7.329837] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 7.342612] panel-simple panel-lcd: Dropping the link to regulator.0 [ 7.350644] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 7.359449] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 7.366352] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 7.391776] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 [ 7.419059] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 7.423197] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 [ 7.426183] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 7.432308] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 [ 7.440685] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 7.452739] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 7.459894] sgtl5000 0-000a: Linked as a consumer to regulator.7 [ 7.466041] sgtl5000 0-000a: Linked as a consumer to regulator.8 [ 7.472232] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 7.479901] sgtl5000 0-000a: sgtl5000 revision 0x11 [ 7.480714] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 7.492357] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 0 [ 7.492391] panel-simple panel-lcd: Dropping the link to regulator.0 [ 7.495271] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum [ 7.515243] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 7.524072] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 7.531004] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 7.539240] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 7.546430] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 7.555046] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 7.562313] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 7.571317] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 7.579844] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 7.586589] panel-simple panel-lcd: Dropping the link to regulator.0 [ 7.594780] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 7.603626] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 7.610548] panel-simple panel-lvds0: Dropping the link to regulator.0 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. IP-Config: eth0 hardware address 00:19:b8:08:f1:13 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.33 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-3 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 8.667877] systemd[1]: System time before build time, advancing clock. [ 8.703610] cgroup: cgroup2: unknown option "memory_recursiveprot" [ 8.719279] systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) [ 8.743227] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! [ 8.791758] systemd[1]: Set hostname to . [ 9.652195] systemd[1]: Queued start job for default target Graphical Interface. [ 9.661521] random: systemd: uninitialized urandom read (16 bytes read) [ 9.668323] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. [ 9.680740] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) [ 9.689885] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. [ 9.729149] random: systemd: uninitialized urandom read (16 bytes read) [ 9.736943] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. [ 9.779104] random: systemd: uninitialized urandom read (16 bytes read) [ 9.786852] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 9.829989] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 9.869850] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. [ 9.909184] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. [ 9.949465] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. [ 9.961911] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. [ 9.999795] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. [ 10.029298] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 10.069195] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. [ 10.099446] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 10.130216] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. [ 10.204018] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. [ 10.214477] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 10.250538] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 10.291531] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. [ 10.332238] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 10.370421] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 10.410032] systemd[1]: Condition check resulted in Huge Pages File System being skipped. [ 10.419195] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. [ 10.431887] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... [ 10.475326] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... [ 10.527256] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... [ 10.572484] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... [ 10.612427] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... [ 10.652467] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... [ 10.694758] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. [ 10.704688] random: systemd: uninitialized urandom read (16 bytes read) [ 10.714770] systemd[1]: Starting Journal Service... Starting Journal Service... [ 10.757767] random: systemd: uninitialized urandom read (16 bytes read) [ 10.767981] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 10.799259] random: systemd: uninitialized urandom read (16 bytes read) [ 10.809653] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... [ 10.851994] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... [ 10.896320] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. [ 10.929633] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. [ 10.970124] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. [ 11.030023] systemd[1]: modprobe@configfs.service: Succeeded. [ 11.036477] systemd[1]: Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module configfs. [ 11.069567] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Apply Kernel Variables... [ 11.364656] systemd-journald[164]: Received client request to flush runtime journal. Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. [ 11.779894] random: systemd: uninitialized urandom read (16 bytes read) Starting Create Static Device Nodes in /dev... [ OK ] Finished Coldplug All udev Devices. [ 11.856822] random: systemd-journal: uninitialized urandom read (16 bytes read) [ OK ] Finished Flush Journal [ 11.869678] random: systemd-journal: uninitialized urandom read (16 bytes read) to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ 12.418920] random: crng init done [ 12.422351] random: 48 urandom warning(s) missed due to ratelimiting [ OK ] Finished Load/Save Random Seed. [ OK ] Started Rule-based Manager for Device Events and Files. [ OK ] Finished Create Volatile Files and Directories. Starting Network Service... Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Found device /dev/ttymxc1. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started Network Name Resolution. [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 4.19.273-cip91 #1 SMP Wed Feb 22 18:47:49 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/9284186/extract-nfsrootfs-obuj4lhr' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/9284186/extract-nfsrootfs-obuj4lhr' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/bash export SHELL=/bin/bash / # . /lava-9284186/environment . /lava-9284186/environment / # /lava-9284186/bin/lava-test-runner /lava-9284186/0 /lava-9284186/bin/lava-test-runner /lava-9284186/0 + export TESTRUN_ID=0_timesync-off + TESTRUN_ID=0_timesync-off + cd /lava-9284186/0/tests/0_timesync-off ++ cat uuid + UUID=9284186_1.6.2.4.1 + set +x + systemctl stop systemd-timesyncd + set +x + export TESTRUN_ID=1_kselftest-filesystems + TESTRUN_ID=1_kselftest-filesystems + cd /lava-9284186/0/tests/1_kselftest-filesystems ++ cat uuid + UUID=9284186_1.6.2.4.5 + set +x + cd ./automated/linux/kselftest/ + ./kselftest.sh -c filesystems -T '' -t kselftest_armhf.tar.gz -s True -u None -L '' -S skipfile-lkft.yaml -b imx6q-sabrelite -g cip-gitlab -e '' -p /opt/kselftests/mainline/ -n 1 -i 1 INFO: Generating a skipfile based on /lava-9284186/0/tests/1_kselftest-filesystems/automated/linux/kselftest/skipfile-lkft.yaml INFO: Using the following generated skipfile contents (until EOF): breakpoints:breakpoint_test breakpoints:step_after_suspend_test ftrace:ftracetest net:rtnetlink.sh net:tls netfilter:bridge_brouter.sh netfilter:nft_flowtable.sh netfilter:nft_trans_stress.sh pidfd:pidfd_wait INFO: EOF INFO: install_deps skipped --2023-02-22 19:04:59-- http://none/ Resolving none (none)... failed: Name or service not known. wget: unable to resolve host address 'none' tar: None: Cannot open: No such file or directory tar: Error is not recoverable: exiting now ./kselftest.sh: 160: cd: can't cd to kselftest / #