[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.36 (8 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 9334797/tftp-deploy-8v1xau6a/kernel/zImage tftp 0x10000000 9334797/tftp-deploy-8v1xau6a/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.36 Filename '9334797/tftp-deploy-8v1xau6a/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 5.3 MiB/s done Bytes transferred = 8729088 (853200 hex) => tftp 0x14000000 9334797/tftp-deploy-8v1xau6a/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 9334797/tftp-deploy-8v1xau6a/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.36 Filename '9334797/tftp-deploy-8v1xau6a/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 5.3 MiB/s done Bytes transferred = 9405364 (8f83b4 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 9334797/tftp-deploy-8v1xau6a/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 9334797/tftp-deploy-8v1xau6a/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.36 Filename '9334797/tftp-deploy-8v1xau6a/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 9.9 MiB/s done Bytes transferred = 41606 (a286 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/9334797/extract-nfsrootfs-33y2v6e6,tcp,hard console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/9334797/extract-nfsrootfs-33y2v6e6,tcp,hard console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x853200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 9405300 Bytes = 9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d285 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.274-cip92 (KernelCI@build-j1107725-arm-gcc-10-multi-v7-defconfig-kd94n) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Sat Feb 25 18:29:02 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] percpu: Embedded 16 pages/cpu s36748 r8192 d20596 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/9334797/extract-nfsrootfs-33y2v6e6,tcp,hard console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 942976K/1048576K available (12288K kernel code, 1597K rwdata, 4684K rodata, 2048K init, 394K bss, 40064K reserved, 65536K cma-reserved, 196608K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1598 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 395 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000006] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008442] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.021418] Console: colour dummy device 80x30 <6>[ 0.023301] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.033720] pid_max: default: 32768 minimum: 301 <6>[ 0.038710] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.045464] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.053286] CPU: Testing write buffer coherency: ok <6>[ 0.057908] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.063558] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.069813] Setting up static identity map for 0x10300000 - 0x103000a0 <6>[ 0.077508] rcu: Hierarchical SRCU implementation. <6>[ 0.084063] EFI services will not be available. <6>[ 0.086311] smp: Bringing up secondary CPUs ... <6>[ 0.091574] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.091581] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.102914] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.102920] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.114101] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.114108] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.124567] smp: Brought up 1 node, 4 CPUs <6>[ 0.128824] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.135242] CPU: All CPU(s) started in SVC mode. <6>[ 0.141195] devtmpfs: initialized <6>[ 0.150997] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.156452] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.166200] futex hash table entries: 1024 (order: 4, 65536 bytes) <6>[ 0.175815] pinctrl core: initialized pinctrl subsystem <6>[ 0.180077] DMI not present or invalid. <6>[ 0.183340] NET: Registered protocol family 16 <6>[ 0.190721] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.197371] cpuidle: using governor menu <6>[ 0.199378] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.214192] vdd1p1: supplied by regulator-dummy <6>[ 0.216660] vdd3p0: supplied by regulator-dummy <6>[ 0.221391] vdd2p5: supplied by regulator-dummy <6>[ 0.226218] vddarm: supplied by regulator-dummy <6>[ 0.231130] vddpu: supplied by regulator-dummy <6>[ 0.235557] vddsoc: supplied by regulator-dummy <6>[ 0.254032] No ATAGs? <6>[ 0.254178] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.262138] hw-breakpoint: maximum watchpoint size is 4 bytes. <4>[ 0.271614] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory <6>[ 0.278498] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver <6>[ 0.290374] Serial: AMBA PL011 UART driver <6>[ 0.294207] console [pstore-1] enabled <6>[ 0.296068] pstore: Registered ramoops as persistent store backend <6>[ 0.302320] ramoops: attached 0x10000@0x30000000, ecc: 0/0 <6>[ 0.330593] mxs-dma 110000.dma-apbh: initialized <6>[ 0.340079] vgaarb: loaded <5>[ 0.341007] SCSI subsystem initialized <6>[ 0.344605] usbcore: registered new interface driver usbfs <6>[ 0.350016] usbcore: registered new interface driver hub <6>[ 0.355550] usbcore: registered new device driver usb <6>[ 0.362120] i2c i2c-0: IMX I2C adapter registered <6>[ 0.365799] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.371894] i2c i2c-1: IMX I2C adapter registered <6>[ 0.376320] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.382276] i2c i2c-2: IMX I2C adapter registered <6>[ 0.386849] i2c i2c-2: can't use DMA, using PIO instead. <6>[ 0.393946] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.397629] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.407038] PTP clock support registered <6>[ 0.411421] EDAC MC: Ver: 3.0.0 <6>[ 0.417427] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.480279] NET: Registered protocol family 2 <6>[ 0.482505] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.490026] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) <6>[ 0.496958] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.504346] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) <6>[ 0.511100] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.517777] UDP hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.523756] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.530520] NET: Registered protocol family 1 <6>[ 0.535496] RPC: Registered named UNIX socket transport module. <6>[ 0.541154] RPC: Registered udp transport module. <6>[ 0.546079] RPC: Registered tcp transport module. <6>[ 0.551056] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.558207] Trying to unpack rootfs image as initramfs... <6>[ 1.284533] Freeing initrd memory: 9188K <4>[ 1.286412] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 1.293686] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 1.303592] Initialise system trusted keyrings <6>[ 1.306651] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 1.319223] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.323108] NFS: Registering the id_resolver key type <5>[ 1.327850] Key type id_resolver registered <5>[ 1.332211] Key type id_legacy registered <6>[ 1.336515] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 1.343224] Key type asymmetric registered <5>[ 1.345438] Asymmetric key parser 'x509' registered <6>[ 1.350650] bounce: pool size: 64 pages <6>[ 1.354696] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 1.362409] io scheduler noop registered <6>[ 1.366490] io scheduler deadline registered <6>[ 1.371173] io scheduler cfq registered (default) <6>[ 1.375974] io scheduler mq-deadline registered <6>[ 1.380777] io scheduler kyber registered <6>[ 1.406941] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 1.411484] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 1.418602] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 1.425891] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 1.446050] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set <6>[ 1.449483] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc <4>[ 1.457261] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set <6>[ 1.463493] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 <4>[ 1.471356] PU : no governor for states <4>[ 1.471447] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 1.475318] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc <6>[ 1.485081] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 1.551376] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 1.558728] SuperH (H)SCI(F) driver initialized <6>[ 1.561572] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX <6>[ 1.570321] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX <6>[ 1.581305] console [ttymxc1] enabled <6>[ 1.581305] console [ttymxc1] enabled <6>[ 1.586287] bootconsole [ec_imx21] disabled <6>[ 1.586287] bootconsole [ec_imx21] disabled <6>[ 1.596419] msm_serial: driver initialized <6>[ 1.602651] STMicroelectronics ASC driver initialized <6>[ 1.609821] STM32 USART driver initialized <4>[ 1.625010] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 1.633709] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 1.640684] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 1.647465] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 1.656473] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 1.663639] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 1.678408] brd: module loaded <6>[ 1.691164] loop: module loaded <6>[ 1.697885] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 1.706079] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 1.714370] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 1.722834] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <6>[ 1.733616] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 1.740919] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 1.750005] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 1.760827] scsi host0: ahci-imx <6>[ 1.764891] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 <6>[ 1.783915] CAN device driver interface <6>[ 1.789306] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 1.796377] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator <6>[ 1.805339] fec 2188000.ethernet: Linked as a consumer to regulator.0 <6>[ 1.814450] pps pps0: new PPS source ptp0 <6>[ 1.835950] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 1.843385] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 1.849504] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 1.855744] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 1.862988] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.874747] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 1.882478] usbcore: registered new interface driver pegasus <6>[ 1.888460] usbcore: registered new interface driver asix <6>[ 1.894157] usbcore: registered new interface driver ax88179_178a <6>[ 1.900567] usbcore: registered new interface driver cdc_ether <6>[ 1.906720] usbcore: registered new interface driver smsc75xx <6>[ 1.912796] usbcore: registered new interface driver smsc95xx <6>[ 1.918861] usbcore: registered new interface driver net1080 <6>[ 1.924818] usbcore: registered new interface driver cdc_subset <6>[ 1.931048] usbcore: registered new interface driver zaurus <6>[ 1.936959] usbcore: registered new interface driver cdc_ncm <6>[ 1.945825] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 1.952652] ehci-pci: EHCI PCI platform driver <6>[ 1.957403] ehci-platform: EHCI generic platform driver <6>[ 1.963221] ehci-orion: EHCI orion driver <6>[ 1.967743] SPEAr-ehci: EHCI SPEAr driver <6>[ 1.972206] ehci-st: EHCI STMicroelectronics driver <6>[ 1.977573] ehci-exynos: EHCI EXYNOS driver <6>[ 1.982209] ehci-atmel: EHCI Atmel driver <6>[ 1.986664] tegra-ehci: Tegra EHCI driver <6>[ 1.991187] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 1.997667] ohci-pci: OHCI PCI platform driver <6>[ 2.002423] ohci-platform: OHCI generic platform driver <6>[ 2.008200] SPEAr-ohci: OHCI SPEAr driver <6>[ 2.012672] ohci-st: OHCI STMicroelectronics driver <6>[ 2.018029] ohci-atmel: OHCI Atmel driver <6>[ 2.023300] usbcore: registered new interface driver usb-storage <6>[ 2.031877] imx_usb 2184000.usb: Linked as a consumer to regulator.9 <6>[ 2.043900] imx_usb 2184200.usb: Linked as a consumer to regulator.14 <6>[ 2.054069] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 2.059264] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 2.087466] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 2.093858] hub 1-0:1.0: USB hub found <6>[ 2.097933] hub 1-0:1.0: 1 port detected <6>[ 2.102165] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 2.107888] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 2.114425] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 2.128213] i2c /dev entries driver <6>[ 2.146380] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) <6>[ 2.157786] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.164235] sdhci: Copyright(c) Pierre Ossman <6>[ 2.171147] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.179436] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.186238] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO <6>[ 2.191697] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO <6>[ 2.197199] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.237035] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA <6>[ 2.245071] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO <6>[ 2.250623] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.290441] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA <6>[ 2.301925] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 2.309026] usbcore: registered new interface driver usbhid <6>[ 2.314897] usbhid: USB HID core driver <6>[ 2.325072] NET: Registered protocol family 10 <6>[ 2.330924] mmc0: new high speed SDHC card at address aaaa <6>[ 2.330955] Segment Routing with IPv6 <6>[ 2.338358] mmcblk0: mmc0:aaaa SL16G 14.8 GiB <6>[ 2.340757] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.352198] NET: Registered protocol family 17 <6>[ 2.356928] can: controller area network core (rev 20170425 abi 9) <6>[ 2.363478] NET: Registered protocol family 29 <6>[ 2.368214] can: raw protocol (rev 20170425) <6>[ 2.372754] can: broadcast manager protocol (rev 20170425 t) <6>[ 2.378702] can: netlink gateway (rev 20170425) max_hops=1 <5>[ 2.384902] Key type dns_resolver registered <6>[ 2.390514] cpu cpu0: Linked as a consumer to regulator.4 <6>[ 2.396235] cpu cpu0: Linked as a consumer to regulator.5 <6>[ 2.401991] cpu cpu0: Linked as a consumer to regulator.6 <6>[ 2.407468] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 2.408497] ThumbEE CPU extension supported. <5>[ 2.418995] Registering SWP/SWPB emulation handler <5>[ 2.424801] Loading compiled-in X.509 certificates <6>[ 2.431544] pstore: Using compression: deflate <4>[ 2.436598] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 2.444391] GPT:29296874 != 31116287 <4>[ 2.448280] GPT:Alternate GPT header not at the end of the disk. <4>[ 2.454568] GPT:29296874 != 31116287 <4>[ 2.458460] GPT: Use GNU Parted to correct GPT errors. <6>[ 2.462715] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.463971] mmcblk0: p1 p2 p3 <6>[ 2.471377] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.483425] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.491146] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.499833] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.508518] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.515456] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.523273] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.532294] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.539412] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.547986] imx_thermal tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <6>[ 2.558510] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.565893] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.574165] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.581631] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.590145] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.598822] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.605792] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.613600] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.622639] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.629822] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.637592] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.645090] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.653289] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.660893] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.669407] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.678084] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.685132] hub 1-1:1.0: USB hub found <6>[ 2.689235] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.697023] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.706060] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.713172] hub 1-1:1.0: 3 ports detected <6>[ 2.717524] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.726004] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 2.733008] hctosys: unable to open rtc device (rtc0) <6>[ 2.739582] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.746981] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.755758] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.763428] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.772071] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.780763] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.787715] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.795501] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.804527] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.811650] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.819361] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.826714] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.834843] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.842301] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 2.870852] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 2.885860] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 5.998118] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 6.007521] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 6.037442] Sending DHCP requests ., OK <6>[ 6.081709] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.36 <6>[ 6.090043] IP-Config: Complete: <6>[ 6.093560] device=eth0, hwaddr=00:19:b8:08:f1:1c, ipaddr=192.168.201.36, mask=255.255.255.0, gw=192.168.201.1 <6>[ 6.104329] host=imx6q-sabrelite-lava-cbg-6, domain=lava-rack, nis-domain=(none) <6>[ 6.112466] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 6.112473] nameserver0=192.168.201.1 <6>[ 6.131344] Freeing unused kernel memory: 2048K <6>[ 6.168223] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u1 <6>[ 6.992502] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 <6>[ 7.000190] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) <4>[ 7.009659] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.018387] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.025433] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.033778] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.041970] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.042859] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.056643] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.056880] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.064774] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.077610] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.077860] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.086220] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.091518] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 7.098979] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 7.130911] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <4>[ 7.155217] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.159657] sgtl5000 0-000a: Linked as a consumer to regulator.7 <6>[ 7.170239] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.177181] sgtl5000 0-000a: Linked as a consumer to regulator.8 <6>[ 7.183589] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.192078] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.193060] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 7.201150] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.213490] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.221850] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.229275] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.231895] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 7.238205] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.251723] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 7.262011] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 7.268511] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 7.275579] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 0 <4>[ 7.284351] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.293136] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.300564] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.309345] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.318448] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.326667] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.335180] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.343889] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.353049] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.361614] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.390007] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.398829] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.408480] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.416703] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.425817] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.435592] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.443986] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.452261] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.461539] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.470846] pwm-backlight backlight-lvds: Dropping the link to regulator.8 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. IP-Config: eth0 hardware address 00:19:b8:08:f1:1c mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.36 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-6 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 8.399148] systemd[1]: System time before build time, advancing clock. <3>[ 8.432912] cgroup: cgroup2: unknown option "memory_recursiveprot" <30>[ 8.447866] systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 8.472675] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! <30>[ 8.509995] systemd[1]: Set hostname to . <30>[ 9.334827] systemd[1]: Queued start job for default target Graphical Interface. <5>[ 9.344533] random: systemd: uninitialized urandom read (16 bytes read) <28>[ 9.351621] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. <28>[ 9.364429] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) <30>[ 9.374028] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. <5>[ 9.407811] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 9.415840] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. <5>[ 9.457760] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 9.465756] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. <30>[ 9.508796] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. <30>[ 9.547918] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. <30>[ 9.588341] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. <30>[ 9.628343] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 9.640899] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. <30>[ 9.678530] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. <30>[ 9.708003] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. <30>[ 9.747985] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. <30>[ 9.778029] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. <30>[ 9.808942] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. <30>[ 9.885766] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. <30>[ 9.896270] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). <30>[ 9.939218] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. <30>[ 9.980248] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. <30>[ 10.020825] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. <30>[ 10.059019] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. <30>[ 10.098961] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 10.108515] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. <30>[ 10.121060] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... <30>[ 10.161921] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... <30>[ 10.203832] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... <30>[ 10.254255] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... <30>[ 10.291234] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... <30>[ 10.332284] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... <30>[ 10.370694] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. <5>[ 10.381063] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 10.391229] systemd[1]: Starting Journal Service... Starting Journal Service... <5>[ 10.432827] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 10.442750] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... <5>[ 10.478114] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 10.488000] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... <30>[ 10.531210] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... <30>[ 10.572837] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. <30>[ 10.618528] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. <30>[ 10.668875] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. <30>[ 10.736528] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... <46>[ 11.040648] systemd-journald[163]: Received client request to flush runtime journal. Starting Apply Kernel Variables... Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. <5>[ 11.488538] random: systemd: uninitialized urandom read (16 bytes read) Starting Create Static Device Nodes in /dev... <5>[ 11.540446] random: systemd-journal: uninitialized urandom read (16 bytes read) [ OK ] Finished [0;1<5>[ 11.551071] random: systemd-journal: uninitialized urandom read (16 bytes read) ;39mColdplug All udev Devices. [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... <5>[ 11.947463] random: crng init done <5>[ 11.951149] random: 48 urandom warning(s) missed due to ratelimiting [ OK ] Finished Load/Save Random Seed. [ OK ] Started Rule-based Manager for Device Events and Files. [ OK ] Finished Create Volatile Files and Directories. Starting Network Service... Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Found device /dev/ttymxc1. [ OK ] Started Network Name Resolution. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 4.19.274-cip92 #1 SMP Sat Feb 25 18:29:02 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/9334797/extract-nfsrootfs-33y2v6e6' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/9334797/extract-nfsrootfs-33y2v6e6' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/bash export SHELL=/bin/bash / # . /lava-9334797/environment . /lava-9334797/environment / # /lava-9334797/bin/lava-test-runner /lava-9334797/0 /lava-9334797/bin/lava-test-runner /lava-9334797/0 + export TESTRUN_ID=0_timesync-off + TESTRUN_ID=0_timesync-off + cd /lava-9334797/0/tests/0_timesync-off ++ cat uuid + UUID=9334797_1.6.2.4.1 + set +x + systemctl stop systemd-timesyncd + set +x + export TESTRUN_ID=1_kselftest-filesystems + TESTRUN_ID=1_kselftest-filesystems + cd /lava-9334797/0/tests/1_kselftest-filesystems ++ cat uuid + UUID=9334797_1.6.2.4.5 + set +x + cd ./automated/linux/kselftest/ + ./kselftest.sh -c filesystems -T '' -t kselftest_armhf.tar.gz -s True -u None -L '' -S skipfile-lkft.yaml -b imx6q-sabrelite -g cip-gitlab -e '' -p /opt/kselftests/mainline/ -n 1 -i 1 INFO: Generating a skipfile based on /lava-9334797/0/tests/1_kselftest-filesystems/automated/linux/kselftest/skipfile-lkft.yaml INFO: Using the following generated skipfile contents (until EOF): breakpoints:breakpoint_test breakpoints:step_after_suspend_test ftrace:ftracetest net:rtnetlink.sh net:tls netfilter:bridge_brouter.sh netfilter:nft_flowtable.sh netfilter:nft_trans_stress.sh pidfd:pidfd_wait INFO: EOF INFO: install_deps skipped --2023-02-25 18:45:34-- http://none/ Resolving none (none)... failed: Name or service not known. wget: unable to resolve host address 'none' tar: None: Cannot open: No such file or directory tar: Error is not recoverable: exiting now ./kselftest.sh: 160: cd: can't cd to kselftest / #