[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.0 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected sst25vf016b with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 6 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.101.101 (3 ms) => setenv serverip 192.168.101.1 setenv serverip 192.168.101.1 => tftp 0x10000000 10062259/tftp-deploy-g4mjiiyr/kernel/zImage tftp 0x10000000 10062259/tftp-deploy-g4mjiiyr/kernel/zImage Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.101 Filename '10062259/tftp-deploy-g4mjiiyr/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 2.3 MiB/s done Bytes transferred = 8729088 (853200 hex) => tftp 0x14000000 10062259/tftp-deploy-g4mjiiyr/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 10062259/tftp-deploy-g4mjiiyr/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.101 Filename '10062259/tftp-deploy-g4mjiiyr/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 2.2 MiB/s done Bytes transferred = 9401446 (8f7466 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 10062259/tftp-deploy-g4mjiiyr/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 10062259/tftp-deploy-g4mjiiyr/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.101 Filename '10062259/tftp-deploy-g4mjiiyr/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 1.7 MiB/s done Bytes transferred = 41606 (a286 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.101.1:/var/lib/lava/dispatcher/tmp/10062259/extract-nfsrootfs-8tr0xlqp,tcp,hard ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.101.1:/var/lib/lava/dispatcher/tmp/10062259/extract-nfsrootfs-8tr0xlqp,tcp,hard ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x853200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 9401382 Bytes = 9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d285 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.281-cip96 (KernelCI@build-j1380402-arm-gcc-10-multi-v7-defconfig-7p2j5) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Thu Apr 20 13:39:35 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] percpu: Embedded 16 pages/cpu s36748 r8192 d20596 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.101.1:/var/lib/lava/dispatcher/tmp/10062259/extract-nfsrootfs-8tr0xlqp,tcp,hard ip=dhcp [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 942980K/1048576K available (12288K kernel code, 1597K rwdata, 4684K rodata, 2048K init, 394K bss, 40060K reserved, 65536K cma-reserved, 196608K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) [ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) [ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1598 kB) [ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 395 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] L2C-310 errata 752271 769419 enabled [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 [ 0.000000] Switching to timer-based delay loop, resolution 15ns [ 0.000007] sched_clock: 32 bits at 66MHz, resolution 15ns, wraps every 32537631224ns [ 0.000022] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 28958491609 ns [ 0.003085] Console: colour dummy device 80x30 [ 0.003128] Calibrating delay loop (skipped), value calculated using timer frequency.. 132.00 BogoMIPS (lpj=660000) [ 0.003143] pid_max: default: 32768 minimum: 301 [ 0.003280] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.003302] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.003840] CPU: Testing write buffer coherency: ok [ 0.003868] CPU0: Spectre v2: using BPIALL workaround [ 0.004237] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.004932] Setting up static identity map for 0x10300000 - 0x103000a0 [ 0.006536] rcu: Hierarchical SRCU implementation. [ 0.009731] EFI services will not be available. [ 0.010031] smp: Bringing up secondary CPUs ... [ 0.010832] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.010839] CPU1: Spectre v2: using BPIALL workaround [ 0.011741] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.011748] CPU2: Spectre v2: using BPIALL workaround [ 0.012619] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.012625] CPU3: Spectre v2: using BPIALL workaround [ 0.012735] smp: Brought up 1 node, 4 CPUs [ 0.012747] SMP: Total of 4 processors activated (528.00 BogoMIPS). [ 0.012756] CPU: All CPU(s) started in SVC mode. [ 0.013819] devtmpfs: initialized [ 0.021103] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.021468] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.021491] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.024677] pinctrl core: initialized pinctrl subsystem [ 0.026305] DMI not present or invalid. [ 0.027134] NET: Registered protocol family 16 [ 0.030581] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.032918] cpuidle: using governor menu [ 0.033111] CPU identified as i.MX6Q, silicon rev 1.0 [ 0.042878] vdd1p1: supplied by regulator-dummy [ 0.043388] vdd3p0: supplied by regulator-dummy [ 0.043875] vdd2p5: supplied by regulator-dummy [ 0.044382] vddarm: supplied by regulator-dummy [ 0.045030] vddpu: supplied by regulator-dummy [ 0.045412] vddsoc: supplied by regulator-dummy [ 0.059501] No ATAGs? [ 0.059641] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.059656] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.063035] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory [ 0.063274] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver [ 0.068383] Serial: AMBA PL011 UART driver [ 0.070710] console [pstore-1] enabled [ 0.070903] pstore: Registered ramoops as persistent store backend [ 0.070918] ramoops: attached 0x10000@0x30000000, ecc: 0/0 [ 0.093462] mxs-dma 110000.dma-apbh: initialized [ 0.100906] vgaarb: loaded [ 0.101733] SCSI subsystem initialized [ 0.102155] usbcore: registered new interface driver usbfs [ 0.102208] usbcore: registered new interface driver hub [ 0.102260] usbcore: registered new device driver usb [ 0.103507] i2c i2c-0: IMX I2C adapter registered [ 0.103530] i2c i2c-0: can't use DMA, using PIO instead. [ 0.104083] i2c i2c-1: IMX I2C adapter registered [ 0.104101] i2c i2c-1: can't use DMA, using PIO instead. [ 0.104513] i2c i2c-2: IMX I2C adapter registered [ 0.104535] i2c i2c-2: can't use DMA, using PIO instead. [ 0.106060] pps_core: LinuxPPS API ver. 1 registered [ 0.106072] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.106096] PTP clock support registered [ 0.106343] EDAC MC: Ver: 3.0.0 [ 0.109075] clocksource: Switched to clocksource mxc_timer1 [ 0.168410] NET: Registered protocol family 2 [ 0.168871] IP idents hash table entries: 16384 (order: 5, 131072 bytes) [ 0.170160] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) [ 0.170202] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.170296] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.170440] TCP: Hash tables configured (established 8192 bind 8192) [ 0.170663] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.170710] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.170883] NET: Registered protocol family 1 [ 0.171405] RPC: Registered named UNIX socket transport module. [ 0.171418] RPC: Registered udp transport module. [ 0.171428] RPC: Registered tcp transport module. [ 0.171437] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.171897] Trying to unpack rootfs image as initramfs... [ 0.890766] Freeing initrd memory: 9184K [ 0.891217] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 0.891618] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 0.893580] Initialise system trusted keyrings [ 0.893865] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 0.899908] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.900541] NFS: Registering the id_resolver key type [ 0.900598] Key type id_resolver registered [ 0.900609] Key type id_legacy registered [ 0.900666] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.902811] Key type asymmetric registered [ 0.902828] Asymmetric key parser 'x509' registered [ 0.902888] bounce: pool size: 64 pages [ 0.902935] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) [ 0.902950] io scheduler noop registered [ 0.902961] io scheduler deadline registered [ 0.903098] io scheduler cfq registered (default) [ 0.903112] io scheduler mq-deadline registered [ 0.903123] io scheduler kyber registered [ 0.924724] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 0.924799] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 0.924946] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 0.924998] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 0.937960] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set [ 0.938038] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc [ 0.938097] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set [ 0.938183] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 [ 0.938400] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 0.938419] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 0.938455] PU : no governor for states [ 0.938477] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc [ 0.992440] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.996039] SuperH (H)SCI(F) driver initialized [ 0.996936] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX [ 0.997720] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX [ 1.904772] console [ttymxc1] enabled [ 1.909681] msm_serial: driver initialized [ 1.914032] STMicroelectronics ASC driver initialized [ 1.920931] STM32 USART driver initialized [ 1.935741] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 1.944180] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 1.950897] panel-simple panel-lcd: Dropping the link to regulator.0 [ 1.957387] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 1.966164] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 1.973074] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 1.987398] brd: module loaded [ 2.000060] loop: module loaded [ 2.006458] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 [ 2.014443] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 [ 2.022478] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 [ 2.030687] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 [ 2.041186] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled [ 2.048183] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 2.057012] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 2.067538] scsi host0: ahci-imx [ 2.071379] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 [ 2.090033] CAN device driver interface [ 2.095131] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 2.101961] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator [ 2.110661] fec 2188000.ethernet: Linked as a consumer to regulator.0 [ 2.119470] pps pps0: new PPS source ptp0 [ 2.141206] fec 2188000.ethernet eth0: registered PHC device 0 [ 2.148351] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 2.154222] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 2.160227] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 2.167194] igb: Copyright (c) 2007-2014 Intel Corporation. [ 2.178642] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 2.186108] usbcore: registered new interface driver pegasus [ 2.191832] usbcore: registered new interface driver asix [ 2.197271] usbcore: registered new interface driver ax88179_178a [ 2.203418] usbcore: registered new interface driver cdc_ether [ 2.209321] usbcore: registered new interface driver smsc75xx [ 2.215118] usbcore: registered new interface driver smsc95xx [ 2.220919] usbcore: registered new interface driver net1080 [ 2.226617] usbcore: registered new interface driver cdc_subset [ 2.232587] usbcore: registered new interface driver zaurus [ 2.238232] usbcore: registered new interface driver cdc_ncm [ 2.246797] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.253363] ehci-pci: EHCI PCI platform driver [ 2.257852] ehci-platform: EHCI generic platform driver [ 2.263403] ehci-orion: EHCI orion driver [ 2.267637] SPEAr-ehci: EHCI SPEAr driver [ 2.271859] ehci-st: EHCI STMicroelectronics driver [ 2.276925] ehci-exynos: EHCI EXYNOS driver [ 2.281326] ehci-atmel: EHCI Atmel driver [ 2.285526] tegra-ehci: Tegra EHCI driver [ 2.289777] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.295978] ohci-pci: OHCI PCI platform driver [ 2.300488] ohci-platform: OHCI generic platform driver [ 2.305986] SPEAr-ohci: OHCI SPEAr driver [ 2.310217] ohci-st: OHCI STMicroelectronics driver [ 2.315284] ohci-atmel: OHCI Atmel driver [ 2.320303] usbcore: registered new interface driver usb-storage [ 2.328573] imx_usb 2184000.usb: Linked as a consumer to regulator.9 [ 2.340385] imx_usb 2184200.usb: Linked as a consumer to regulator.14 [ 2.350284] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 2.355192] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 [ 2.389102] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 2.395182] hub 1-0:1.0: USB hub found [ 2.398976] hub 1-0:1.0: 1 port detected [ 2.409221] i2c /dev entries driver [ 2.410599] ata1: SATA link down (SStatus 0 SControl 300) [ 2.418153] ahci-imx 2200000.sata: no device found, disabling link. [ 2.423965] imx_thermal tempmon: invalid sensor calibration data [ 2.424453] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug [ 2.430468] imx_thermal tempmon: failed to init from from fsl,tempmon-data [ 2.444491] imx_thermal: probe of tempmon failed with error -22 [ 2.453720] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) [ 2.464894] sdhci: Secure Digital Host Controller Interface driver [ 2.471101] sdhci: Copyright(c) Pierre Ossman [ 2.477720] Synopsys Designware Multimedia Card Interface Driver [ 2.485711] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.492277] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO [ 2.497450] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO [ 2.502711] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 [ 2.542289] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA [ 2.550060] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO [ 2.555305] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 [ 2.594918] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA [ 2.606097] ledtrig-cpu: registered to indicate activity on CPUs [ 2.612964] usbcore: registered new interface driver usbhid [ 2.618582] usbhid: USB HID core driver [ 2.628373] NET: Registered protocol family 10 [ 2.628448] mmc0: new high speed SDHC card at address 0001 [ 2.633923] Segment Routing with IPv6 [ 2.640021] mmcblk0: mmc0:0001 SD 14.8 GiB [ 2.642180] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.652786] NET: Registered protocol family 17 [ 2.657249] can: controller area network core (rev 20170425 abi 9) [ 2.663535] NET: Registered protocol family 29 [ 2.667990] can: raw protocol (rev 20170425) [ 2.672288] can: broadcast manager protocol (rev 20170425 t) [ 2.677960] can: netlink gateway (rev 20170425) max_hops=1 [ 2.683912] Key type dns_resolver registered [ 2.689019] cpu cpu0: Linked as a consumer to regulator.4 [ 2.694517] cpu cpu0: Linked as a consumer to regulator.5 [ 2.700010] cpu cpu0: Linked as a consumer to regulator.6 [ 2.706236] ThumbEE CPU extension supported. [ 2.709117] usb 1-1: new high-speed USB device number 2 using ci_hdrc [ 2.710545] Registering SWP/SWPB emulation handler [ 2.722623] Loading compiled-in X.509 certificates [ 2.729424] pstore: Using compression: deflate [ 2.749632] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 2.756763] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 2.765288] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 2.772796] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 2.781556] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 2.790001] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 2.796824] panel-simple panel-lcd: Dropping the link to regulator.0 [ 2.804703] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 2.813503] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 2.820587] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 2.828425] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 2.835689] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 2.843927] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 2.851286] GPT:Primary header thinks Alt. header is not at the end of the disk. [ 2.858689] GPT:29296874 != 30965759 [ 2.862293] GPT:Alternate GPT header not at the end of the disk. [ 2.868304] GPT:29296874 != 30965759 [ 2.871913] GPT: Use GNU Parted to correct GPT errors. [ 2.877101] mmcblk0: p1 p2 p3 [ 2.880394] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 2.889012] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 2.897458] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 2.906185] panel-simple panel-lcd: Dropping the link to regulator.0 [ 2.914107] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 2.922927] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 2.931872] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 2.939588] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 2.946689] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 2.954888] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 2.962139] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 2.970655] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 2.979091] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 2.985838] panel-simple panel-lcd: Dropping the link to regulator.0 [ 2.994185] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 [ 3.001181] hctosys: unable to open rtc device (rtc0) [ 3.007043] hub 1-1:1.0: USB hub found [ 3.014233] hub 1-1:1.0: 3 ports detected [ 3.019415] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 3.028178] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 3.035175] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 3.043017] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 3.050209] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 3.058414] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 3.065829] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 3.074400] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 3.082836] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 3.089568] panel-simple panel-lcd: Dropping the link to regulator.0 [ 3.097734] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 3.106545] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 3.113455] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 3.119695] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:06: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:06, irq=POLL) [ 3.121149] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 3.134582] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 3.141576] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 3.155556] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 3.162774] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 3.171284] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 3.179714] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 3.186400] panel-simple panel-lcd: Dropping the link to regulator.0 [ 5.209864] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx [ 5.239193] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 5.269245] Sending DHCP requests ., OK [ 5.313036] IP-Config: Got DHCP answer from 192.168.101.1, my address is 192.168.101.101 [ 5.321200] IP-Config: Complete: [ 5.324455] device=eth0, hwaddr=00:19:b8:00:e5:47, ipaddr=192.168.101.101, mask=255.255.255.0, gw=192.168.101.1 [ 5.335022] host=imx6q-sabrelite-cbg-2, domain=lava.cbg.collabora.co.uk, nis-domain=(none) [ 5.343764] bootserver=192.168.101.1, rootserver=192.168.101.1, rootpath= [ 5.343774] nameserver0=192.168.101.1 [ 5.362019] Freeing unused kernel memory: 2048K [ 5.389765] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u1 [ 6.393121] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 6.402009] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 6.419841] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) [ 6.430195] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 [ 6.437669] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) [ 6.446053] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 6.454202] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 6.461464] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) [ 6.468280] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) [ 6.474872] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 [ 6.481143] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 6.489883] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 6.497092] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 6.506217] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 6.514707] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 6.521458] panel-simple panel-lcd: Dropping the link to regulator.0 [ 6.530142] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 6.538923] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 6.545862] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 6.558191] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 6.565398] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 6.573601] sgtl5000 0-000a: Linked as a consumer to regulator.7 [ 6.579837] sgtl5000 0-000a: Linked as a consumer to regulator.8 [ 6.587202] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 6.596909] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 6.598691] sgtl5000 0-000a: sgtl5000 revision 0x11 [ 6.606355] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 [ 6.607020] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 6.607098] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 6.608320] panel-simple panel-lcd: Dropping the link to regulator.0 [ 6.610089] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 6.645190] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 6.648135] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum [ 6.654327] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 6.678211] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 [ 6.684432] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 [ 6.692278] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 0 [ 6.701626] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 6.710377] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 6.719291] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 6.728045] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 6.737365] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 6.745840] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 6.754096] panel-simple panel-lcd: Dropping the link to regulator.0 [ 6.762529] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 6.771347] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 6.779468] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 6.802673] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 6.811288] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 6.820224] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 6.828614] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 6.837842] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 6.846370] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 6.853696] panel-simple panel-lcd: Dropping the link to regulator.0 [ 6.862216] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 6.871113] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 6.878587] panel-simple panel-lvds0: Dropping the link to regulator.0 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. IP-Config: eth0 hardware address 00:19:b8:00:e5:47 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.101.1): address: 192.168.101.101 broadcast: 192.168.101.255 netmask: 255.255.255.0 gateway: 192.168.101.1 dns0 : 192.168.101.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-cbg-2 domain : lava.cbg.collabora.co.uk rootserver: 192.168.101.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 10.460316] systemd[1]: System time before build time, advancing clock. [ 10.525756] cgroup: cgroup2: unknown option "memory_recursiveprot" [ 10.543274] systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) [ 10.567065] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! [ 10.611885] systemd[1]: Set hostname to . [ 11.639436] systemd[1]: Queued start job for default target Graphical Interface. [ 11.648649] random: systemd: uninitialized urandom read (16 bytes read) [ 11.655594] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. [ 11.668027] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) [ 11.677345] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. [ 11.709542] random: systemd: uninitialized urandom read (16 bytes read) [ 11.717293] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. [ 11.749512] random: systemd: uninitialized urandom read (16 bytes read) [ 11.757336] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 11.800309] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 11.840026] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. [ 11.879931] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. [ 11.919705] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. [ 11.932098] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. [ 11.970182] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. [ 11.999643] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 12.039491] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. [ 12.069768] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 12.100544] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. [ 12.186046] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. [ 12.195987] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 12.230630] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 12.271688] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. [ 12.312833] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 12.351451] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 12.390485] systemd[1]: Condition check resulted in Huge Pages File System being skipped. [ 12.399712] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. [ 12.412316] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... [ 12.455150] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... [ 12.606147] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... [ 12.649789] random: systemd: uninitialized urandom read (16 bytes read) [ 12.659651] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... [ 12.699661] random: systemd: uninitialized urandom read (16 bytes read) [ 12.710889] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... [ 12.749699] random: systemd: uninitialized urandom read (16 bytes read) [ 12.760826] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... [ 12.805699] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. [ 12.821483] systemd[1]: Starting Journal Service... Starting Journal Service... [ 12.869730] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 12.902697] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... [ 12.942751] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... [ 12.986080] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. [ 13.020242] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. [ 13.060922] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. [ 13.109155] random: crng init done [ 13.112577] random: 22 urandom warning(s) missed due to ratelimiting [ 13.133742] systemd[1]: modprobe@configfs.service: Succeeded. [ 13.140438] systemd[1]: Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module configfs. [ 13.181112] systemd[1]: modprobe@drm.service: Succeeded. [ 13.187276] systemd[1]: Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module drm. [ 13.220014] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Apply Kernel Variables... [ 13.490276] systemd-journald[162]: Received client request to flush runtime journal. Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Coldplug All udev Devices. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... [ OK ] Finished Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Found device /dev/ttymxc1. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started Network Name Resolution. [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 4.19.281-cip96 #1 SMP Thu Apr 20 13:39:35 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/10062259/extract-nfsrootfs-8tr0xlqp' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/10062259/extract-nfsrootfs-8tr0xlqp' / # export NFS_SERVER_IP='192.168.101.1' export NFS_SERVER_IP='192.168.101.1' / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-10062259/environment . /lava-10062259/environment / # /lava-10062259/bin/lava-test-runner /lava-10062259/0 /lava-10062259/bin/lava-test-runner /lava-10062259/0 + export TESTRUN_ID=0_dmesg + cd /lava-10062259/0/tests/0_dmesg + cat uuid + UUID=10062259_1.6.2.4.1 + [ 30.623317] set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh [ 30.777378] [ 30.881640] [ 31.004368] + set +x [ 31.013644] # / # #export SHELL=/bin/sh / # export SHELL=/bin/sh. /lava-10062259/environment / # . /lava-10062259/environment/lava-10062259/bin/lava-test-runner /lava-10062259/1 / # /lava-10062259/bin/lava-test-runner /lava-10062259/1 + export TESTRUN_ID=1_bootrr + cd /lava-10062259/1/tests/1_bootrr + cat uuid + UUID=10062259_1.6.2.4.5 + [ 31.651649] set +x + export PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-10062259/1/../bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto backlight-lcd backlight-lvds panel-lcd panel-lvds0 /lava-10062259/1/../bin/lava-test-case [ 32.863969] /lava-10062259/1/../bin/lava-test-case [ 32.965625] /lava-10062259/1/../bin/lava-test-case [ 33.028460] + set +x [ 33.075920] [ 33.13�