Connected to r8a774b1-hihope-rzg2n-ex-01 console [channel connected] (~$quit to exit)
[    0.000144] NOTICE:  BL2: RZ G2N Initial Program Loader(CA57)
[    0.004408] NOTICE:  BL2: Initial Program Loader(Rev.2.0.4)
[    0.009941] NOTICE:  BL2: PRR is RZG G2N Ver.1.1
[    0.014523] NOTICE:  BL2: Board is HiHope RZ/G2N Rev.1.0
[    0.019788] NOTICE:  BL2: Boot device is QSPI Flash(40MHz)
[    0.025228] NOTICE:  BL2: LCM state is CM
[    0.029209] NOTICE:  BL2: DDR3200(rev.0.37)
[    0.036160] NOTICE:  BL2: [COLD_BOOT]
[    0.040795] NOTICE:  BL2: DRAM Split is OFF
[    0.043490] NOTICE:  BL2: QoS is default setting(rev.0.09)
[    0.048933] NOTICE:  BL2: DRAM refresh interval 1.95 usec
[    0.054290] NOTICE:  BL2: Periodic Write DQ Training
[    0.059317] NOTICE:  BL2: Lossy Decomp areas
[    0.063449] NOTICE:       Entry 0: DCMPAREACRAx:0x80000540 DCMPAREACRBx:0x570
[    0.070533] NOTICE:       Entry 1: DCMPAREACRAx:0x40000000 DCMPAREACRBx:0x0
[    0.077446] NOTICE:       Entry 2: DCMPAREACRAx:0x20000000 DCMPAREACRBx:0x0
[    0.084360] NOTICE:  BL2: v1.5(release):236f8fb-dirty
[    0.089368] NOTICE:  BL2: Built : 08:01:16, Oct 21 2019
[    0.094556] NOTICE:  BL2: Normal boot
[    0.098196] NOTICE:  BL2: dst=0xe6320100 src=0x8180000 len=512(0x200)
[    0.104684] NOTICE:  BL2: dst=0x43f00000 src=0x8180400 len=6144(0x1800)
[    0.112412] NOTICE:  BL2: dst=0x44000000 src=0x81c0000 len=65536(0x10000)
[    0.131323] NOTICE:  BL2: dst=0x50000000 src=0x8300000 len=1048576(0x100000)
[    0.351571] NOTICE:  BL2: Booting BL31


U-Boot 2018.09 (Oct 21 2019 - 05:40:53 +0000)

CPU: Renesas Electronics R8A774B1 rev 1.1
Model: Hoperun Technology HiHope RZ/G2N platform (hihope-rzg2n)
DRAM:  3.9 GiB
Bank #0: 0x048000000 - 0x0bfffffff, 1.9 GiB
Bank #1: 0x480000000 - 0x4ffffffff, 2 GiB

Error reading output register
Error reading output register
Error reading output register
Error reading output register
MMC:   sd@ee100000: 0, sd@ee160000: 1
Loading Environment from MMC... OK
In:    serial@e6e88000
Out:   serial@e6e88000
Err:   serial@e6e88000
Net:   eth0: ethernet@e6800000
Hit any key to stop autoboot:  2 
 0 
=> setenv autoload no
setenv autoload no
=> setenv initrd_high 0xffffffff
setenv initrd_high 0xffffffff
=> setenv fdt_high 0xffffffff
setenv fdt_high 0xffffffff
=> dhcp
dhcp
ethernet@e6800000 Waiting for PHY auto negotiation to complete.... done
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
DHCP client bound to address 192.168.1.12 (1290 ms)
=> setenv serverip 192.168.1.1
setenv serverip 192.168.1.1
=> tftp 0x48080000 947323/tftp-deploy-o7hp7mhj/kernel/Image
tftp 0x48080000 947323/tftp-deploy-o7hp7mhj/kernel/Image
Using ethernet@e6800000 device
TFTP from server 192.168.1.1; our IP address is 192.168.1.12
Filename '947323/tftp-deploy-o7hp7mhj/kernel/Image'.
Load address: 0x48080000
Loading: *##################T #######T #######T ##################################
	 ##############################################T ###################
	 ####################T #############################################
	 ####################T ######################################T #######
	 #################################################################
	 ##############################T ###################################
	 #################################################################
	 #######################T ###########T ################################
	 #################################################################
	 ###########################################################
Retry count exceeded; starting again
=>