Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. NOTICE: UDIMM 18ASF1G72AZ-2G1A1 NOTICE: 16 GB DDR4, 64-bit, CL=13, ECC on, 256B, CS0+CS1 NOTICE: UDIMM 18ASF1G72AZ-2G1A1 NOTICE: 4 GB DDR4, 32-bit, CL=11, ECC on, CS0+CS1 NOTICE: BL2: v1.5(release):LSDK-19.06 NOTICE: BL2: Built : 21:37:56, Jul 29 2019 NOTICE: BL2: Booting BL31NOTICE: BL31: v1.5(release):LSDK-19.06 NOTICE: BL31: Built : 21:38:04, Jul 29 2019 NOTICE: Welcome to LS2088 BL31 Phase U-Boot 2019.04-gcbd7e30bf8 (Jul 29 2019 - 21:37:23 +0800) SoC: LS2088AE Rev1.0 (0x87090010) Clock Configuration: CPU0(A72):1800 MHz CPU1(A72):1800 MHz CPU2(A72):1800 MHz CPU3(A72):1800 MHz CPU4(A72):1800 MHz CPU5(A72):1800 MHz CPU6(A72):1800 MHz CPU7(A72):1800 MHz Bus: 700 MHz DDR: 1866.667 MT/s DP-DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 483038b8 48480048 00000000 00000000 00000010: 00000000 00000000 00a00000 00000000 00000020: 01e01180 00002581 00000000 00000000 00000030: 00400c0b 00000000 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000000 00000000 00027000 00000000 00000070: 412a0000 00040000 Model: Freescale Layerscape 2080a RDB Board Board: LS2088AE Rev1.0-RDB, Board Arch: V1, Board version: D, boot from vBank: 4 FPGA: v1.18 SERDES1 Reference : Clock1 = 156.25MHz Clock2 = 156.25MHz SERDES2 Reference : Clock1 = 100MHz Clock2 = 100MHz I2C: ready DRAM: 15.9 GiB DDR 15.9 GiB (DDR4, 64-bit, CL=13, ECC on) DDR Controller Interleaving Mode: 256B DDR Chip-Select Interleaving Mode: CS0+CS1 SEC0: RNG instantiated SEC0: RNG instantiated Using SERDES1 Protocol: 42 (0x2a) Using SERDES2 Protocol: 65 (0x41) Flash: 128 MiB NAND: 2048 MiB MMC: FSL_SDHC: 0 Loading Environment from Flash... OK EEPROM: Invalid ID (ff ff ff ff) In: serial Out: serial Err: serial VID: Core voltage after adjustment is at 1054 mV Net: DPMAC5@xgmii running firmware version 2.3.5 DPMAC5@xgmii: system interface XFI DPMAC5@xgmii: Aquantia AQR405 Firmware Version 2.3.5 DPMAC6@xgmii running firmware version 2.3.5 DPMAC6@xgmii: system interface XFI DPMAC6@xgmii: Aquantia AQR405 Firmware Version 2.3.5 DPMAC7@xgmii running firmware version 2.3.5 DPMAC7@xgmii: system interface XFI DPMAC7@xgmii: Aquantia AQR405 Firmware Version 2.3.5 DPMAC8@xgmii running firmware version 2.3.5 DPMAC8@xgmii: system interface XFI DPMAC8@xgmii: Aquantia AQR405 Firmware Version 2.3.5 PCIe0: pcie@3400000 disabled PCIe1: pcie@3500000 disabled PCIe2: pcie@3600000 Root Complex: x1 gen1 PCIe3: pcie@3700000 Root Complex: no link e1000: 68:05:ca:36:8d:e8 DPMAC1@xgmii Warning: DPMAC1@xgmii (eth0) using random MAC address - 26:fe:94:50:e5:84 , DPMAC2@xgmii Warning: DPMAC2@xgmii (eth1) using random MAC address - 7e:03:c1:4c:5e:15 , DPMAC3@xgmii Warning: DPMAC3@xgmii (eth2) using random MAC address - 76:0b:e8:36:d2:19 , DPMAC4@xgmii Warning: DPMAC4@xgmii (eth3) using random MAC address - 4e:50:15:96:3b:11 , DPMAC5@xgmii Warning: DPMAC5@xgmii (eth4) using random MAC address - 46:58:3c:ec:b7:1d , DPMAC6@xgmii Warning: DPMAC6@xgmii (eth5) using random MAC address - 62:42:e4:26:80:d1 , DPMAC7@xgmii Warning: DPMAC7@xgmii (eth6) using random MAC address - 6a:4a:cd:5c:0c:dd , DPMAC8@xgmii Warning: DPMAC8@xgmii (eth7) using random MAC address - 52:11:30:fc:e5:d5 , e1000#0 [PRIME] crc32+ fsl-mc: Booting Management Complex ... SUCCESS fsl-mc: Management Complex booted (version: 10.16.2, boot status: 0x1) Hit any key to stop autoboot: 10  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => setenv ipaddr 172.16.1.11; setenv serverip 172.16.1.4; setenv ethact e1000#0; setenv ethprime e1000#0 setenv ipaddr 172.16.1.11; setenv serverip 172.16.1.4; setenv ethact e1000#0; setenv ethprime e1000#0 => setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 => tftp 0x80080000 1230805/tftp-deploy-ihj_xajm/kernel/uImage tftp 0x80080000 1230805/tftp-deploy-ihj_xajm/kernel/uImage Using e1000#0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.11 Filename '1230805/tftp-deploy-ihj_xajm/kernel/uImage'. Load address: 0x80080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################ 2.6 MiB/s done Bytes transferred = 19307072 (1269a40 hex) => tftp 0x91000000 1230805/tftp-deploy-ihj_xajm/ramdisk/ramdisk.cpio.gz.uboot tftp 0x91000000 1230805/tftp-deploy-ihj_xajm/ramdisk/ramdisk.cpio.gz.uboot Using e1000#0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.11 Filename '1230805/tftp-deploy-ihj_xajm/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x91000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################ 2.2 MiB/s done Bytes transferred = 15190587 (e7ca3b hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 1230805/tftp-deploy-ihj_xajm/dtb/fsl-ls2088a-rdb.dtb tftp 0x90000000 1230805/tftp-deploy-ihj_xajm/dtb/fsl-ls2088a-rdb.dtb Using e1000#0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.11 Filename '1230805/tftp-deploy-ihj_xajm/dtb/fsl-ls2088a-rdb.dtb'. Load address: 0x90000000 Loading: *## 1000 Bytes/s done Bytes transferred = 16643 (4103 hex) => setenv bootargs 'console=ttyS1,115200n8 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0600 nousb default_hugepagesz=2m hugepagesz=2m hugepages=256 arm-smmu-mod.disable_bypass=n arm-smmu.disable_bypass=n ip=dhcp' setenv bootargs 'console=ttyS1,115200n8 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0600 nousb default_hugepagesz=2m hugepagesz=2m hugepages=256 arm-smmu-mod.disable_bypass=n arm-smmu.disable_bypass=n ip=dhcp' => bootm 0x80080000 0x91000000 0x90000000 bootm 0x80080000 0x91000000 0x90000000 ## Booting kernel from Legacy Image at 80080000 ... Image Name: Created: 2023-07-14 0:56:59 UTC Image Type: AArch64 Linux Kernel Image (uncompressed) Data Size: 19307008 Bytes = 18.4 MiB Load Address: 80080000 Entry Point: 80080000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 91000000 ... Image Name: Created: 2023-07-14 0:57:02 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 15190523 Bytes = 14.5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Loading Kernel Image ... OK Using Device Tree in place at 0000000090000000, end 0000000090007102 fsl-mc: DPL not deployed, DPAA2 ethernet not work Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd082] [ 0.000000] Linux version 4.19.284-cip98 (KernelCI@build-j1586045-arm64-gcc-10-defconfig-6mx6m) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP PREEMPT Tue May 30 14:22:05 UTC 2023 [ 0.000000] Machine model: Freescale Layerscape 2088A RDB Board [ 0.000000] earlycon: uart8250 at MMIO 0x00000000021c0600 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 32 MiB at 0x00000000f9c00000 [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x000000837fffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x837ffdda40-0x837ffdf1ff] [ 0.000000] Zone ranges: [ 0.000000] DMA32 [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] Normal [mem 0x0000000100000000-0x000000837fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fbdfffff] [ 0.000000] node 0: [mem 0x0000008080000000-0x000000837fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000837fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 22 pages/cpu s52760 r8192 d29160 u90112 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: enabling workaround for Branch predictor hardening [ 0.000000] CPU features: enabling workaround for EL2 vector hardening [ 0.000000] Speculative Store Bypass Disable mitigation not required [ 0.000000] CPU features: enabling workaround for Spectre-BHB [ 0.000000] CPU features: enabling workaround for ARM erratum 1742098 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 3595776 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttyS1,115200n8 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0600 nousb default_hugepagesz=2m hugepagesz=2m hugepages=256 arm-smmu-mod.disable_bypass=n arm-smmu.disable_bypass=n ip=dhcp [ 0.000000] software IO TLB: mapped [mem 0xf5c00000-0xf9c00000] (64MB) [ 0.000000] Memory: 14249232K/14612480K available (11196K kernel code, 1382K rwdata, 4964K rodata, 1280K init, 377K bss, 330480K reserved, 32768K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=8. [ 0.000000] Tasks RCU enabled. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: Distributor has no Range Selector support [ 0.000000] GICv3: no VLPI support, no direct LPI support [ 0.000000] ITS [mem 0x06020000-0x0603ffff] [ 0.000000] ITS@0x0000000006020000: allocated 8192 Devices @8371850000 (flat, esz 8, psz 64K, shr 0) [ 0.000000] ITS: using cache flushing for cmd queue [ 0.000000] GIC: using LPI property table @0x0000008371860000 [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006100000 [ 0.000000] CPU0: using LPI pending table @0x0000008371870000 [ 0.000000] GIC: using cache flushing for LPI property table [ 0.000000] arch_timer: Enabling global workaround for Freescale erratum a005858 [ 0.000000] arch_timer: CPU0: Trapping CNTVCT access [ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c409fb33, max_idle_ns: 440795203156 ns [ 0.000002] sched_clock: 56 bits at 25MHz, resolution 39ns, wraps every 4398046511103ns [ 0.008221] Console: colour dummy device 80x25 [ 0.012722] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) [ 0.023158] pid_max: default: 32768 minimum: 301 [ 0.027833] Security Framework initialized [ 0.035468] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes) [ 0.044680] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes) [ 0.052037] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes) [ 0.059016] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes) [ 0.066921] ASID allocator initialised with 32768 entries [ 0.072403] rcu: Hierarchical SRCU implementation. [ 0.077364] Platform MSI: gic-its@6020000 domain created [ 0.082746] PCI/MSI: /interrupt-controller@6000000/gic-its@6020000 domain created [ 0.090564] EFI services will not be available. [ 0.095284] smp: Bringing up secondary CPUs ... [ 0.100052] Detected PIPT I-cache on CPU1 [ 0.100068] GICv3: CPU1: found redistributor 1 region 0:0x0000000006120000 [ 0.100100] CPU1: using LPI pending table @0x000000836fdf0000 [ 0.100115] arch_timer: CPU1: Trapping CNTVCT access [ 0.100118] CPU1: Booted secondary processor 0x0000000001 [0x410fd082] [ 0.100358] Detected PIPT I-cache on CPU2 [ 0.100372] GICv3: CPU2: found redistributor 100 region 0:0x0000000006140000 [ 0.100403] CPU2: using LPI pending table @0x000000836fe50000 [ 0.100419] arch_timer: CPU2: Trapping CNTVCT access [ 0.100423] CPU2: Booted secondary processor 0x0000000100 [0x410fd082] [ 0.100658] Detected PIPT I-cache on CPU3 [ 0.100668] GICv3: CPU3: found redistributor 101 region 0:0x0000000006160000 [ 0.100697] CPU3: using LPI pending table @0x000000836fe60000 [ 0.100709] arch_timer: CPU3: Trapping CNTVCT access [ 0.100712] CPU3: Booted secondary processor 0x0000000101 [0x410fd082] [ 0.100941] Detected PIPT I-cache on CPU4 [ 0.100954] GICv3: CPU4: found redistributor 200 region 0:0x0000000006180000 [ 0.100986] CPU4: using LPI pending table @0x000000836fe80000 [ 0.101001] arch_timer: CPU4: Trapping CNTVCT access [ 0.101005] CPU4: Booted secondary processor 0x0000000200 [0x410fd082] [ 0.101245] Detected PIPT I-cache on CPU5 [ 0.101255] GICv3: CPU5: found redistributor 201 region 0:0x00000000061a0000 [ 0.101284] CPU5: using LPI pending table @0x000000836fed0000 [ 0.101296] arch_timer: CPU5: Trapping CNTVCT access [ 0.101299] CPU5: Booted secondary processor 0x0000000201 [0x410fd082] [ 0.101526] Detected PIPT I-cache on CPU6 [ 0.101541] GICv3: CPU6: found redistributor 300 region 0:0x00000000061c0000 [ 0.101573] CPU6: using LPI pending table @0x000000836fef0000 [ 0.101588] arch_timer: CPU6: Trapping CNTVCT access [ 0.101593] CPU6: Booted secondary processor 0x0000000300 [0x410fd082] [ 0.101828] Detected PIPT I-cache on CPU7 [ 0.101839] GICv3: CPU7: found redistributor 301 region 0:0x00000000061e0000 [ 0.101868] CPU7: using LPI pending table @0x000000836ff00000 [ 0.101880] arch_timer: CPU7: Trapping CNTVCT access [ 0.101884] CPU7: Booted secondary processor 0x0000000301 [0x410fd082] [ 0.101920] smp: Brought up 1 node, 8 CPUs [ 0.305308] SMP: Total of 8 processors activated. [ 0.310048] CPU features: detected: GIC system register CPU interface [ 0.316548] CPU features: detected: 32-bit EL0 Support [ 0.322239] CPU: All CPU(s) started at EL2 [ 0.326385] alternatives: patching kernel code [ 0.331412] devtmpfs: initialized [ 0.335904] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.345746] futex hash table entries: 2048 (order: 5, 131072 bytes) [ 0.352371] pinctrl core: initialized pinctrl subsystem [ 0.358063] DMI not present or invalid. [ 0.362173] NET: Registered protocol family 16 [ 0.366793] audit: initializing netlink subsys (disabled) [ 0.372281] audit: type=2000 audit(0.252:1): state=initialized audit_enabled=0 res=1 [ 0.380082] cpuidle: using governor menu [ 0.384144] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.391441] DMA: preallocated 256 KiB pool for atomic allocations [ 0.397892] Serial: AMBA PL011 UART driver [ 0.402674] Machine: Freescale Layerscape 2088A RDB Board [ 0.408117] SoC family: QorIQ LS2088A [ 0.411796] SoC ID: svr:0x87090010, Revision: 1.0 [ 0.426365] HugeTLB registered 2.00 MiB page size, pre-allocated 256 pages [ 0.433536] cryptd: max_cpu_qlen set to 1000 [ 0.438140] ACPI: Interpreter disabled. [ 0.442347] vgaarb: loaded [ 0.445159] SCSI subsystem initialized [ 0.449164] usbcore: registered new interface driver usbfs [ 0.454701] usbcore: registered new interface driver hub [ 0.460063] usbcore: registered new device driver usb [ 0.465340] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported [ 0.472700] i2c i2c-0: IMX I2C adapter registered [ 0.477438] i2c i2c-0: can't use DMA, using PIO instead. [ 0.482940] pps_core: LinuxPPS API ver. 1 registered [ 0.487933] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.497142] PTP clock support registered [ 0.501139] EDAC MC: Ver: 3.0.0 [ 0.504655] Advanced Linux Sound Architecture Driver Initialized. [ 0.511076] clocksource: Switched to clocksource arch_sys_counter [ 0.517264] VFS: Disk quotas dquot_6.6.0 [ 0.521229] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.528202] pnp: PnP ACPI: disabled [ 0.534226] NET: Registered protocol family 2 [ 0.539235] IP idents hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.549210] tcp_listen_portaddr_hash hash table entries: 8192 (order: 5, 131072 bytes) [ 0.557360] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.565321] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 0.572504] TCP: Hash tables configured (established 131072 bind 65536) [ 0.579268] UDP hash table entries: 8192 (order: 6, 262144 bytes) [ 0.585597] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes) [ 0.592399] NET: Registered protocol family 1 [ 0.597012] RPC: Registered named UNIX socket transport module. [ 0.602970] RPC: Registered udp transport module. [ 0.607699] RPC: Registered tcp transport module. [ 0.612428] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.618972] Unpacking initramfs... [ 0.983615] Freeing initrd memory: 14828K [ 0.988021] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 0.995962] kvm [1]: 8-bit VMID [ 0.999368] kvm [1]: vgic-v2@c0e0000 [ 1.002969] kvm [1]: GIC system register CPU interface enabled [ 1.008927] kvm [1]: vgic interrupt IRQ1 [ 1.012964] kvm [1]: Hyp mode initialized successfully [ 1.019738] Initialise system trusted keyrings [ 1.024279] workingset: timestamp_bits=44 max_order=22 bucket_order=0 [ 1.033157] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.039296] NFS: Registering the id_resolver key type [ 1.044390] Key type id_resolver registered [ 1.048598] Key type id_legacy registered [ 1.052633] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.059377] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 1.066874] 9p: Installing v9fs 9p2000 file system support [ 1.073820] Key type asymmetric registered [ 1.077941] Asymmetric key parser 'x509' registered [ 1.082864] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244) [ 1.090306] io scheduler noop registered [ 1.094254] io scheduler deadline registered [ 1.098586] io scheduler cfq registered (default) [ 1.103333] io scheduler mq-deadline registered [ 1.107890] io scheduler kyber registered [ 1.114379] layerscape-pcie 3600000.pcie: host bridge /soc/pcie@3600000 ranges: [ 1.121753] layerscape-pcie 3600000.pcie: IO 0x3000010000..0x300001ffff -> 0x00000000 [ 1.129907] layerscape-pcie 3600000.pcie: MEM 0x3040000000..0x307fffffff -> 0x40000000 [ 1.138128] layerscape-pcie 3600000.pcie: PCI host bridge to bus 0000:00 [ 1.144874] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.150394] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 1.156613] pci_bus 0000:00: root bus resource [mem 0x3040000000-0x307fffffff] (bus address [0x40000000-0x7fffffff]) [ 1.169116] pci 0000:00:00.0: BAR 1: assigned [mem 0x3040000000-0x3043ffffff] [ 1.176301] pci 0000:00:00.0: BAR 0: assigned [mem 0x3044000000-0x3044ffffff] [ 1.183486] pci 0000:00:00.0: BAR 6: assigned [mem 0x3045000000-0x3045ffffff pref] [ 1.191103] pci 0000:00:00.0: BAR 14: assigned [mem 0x3046000000-0x30460fffff] [ 1.198372] pci 0000:00:00.0: BAR 13: assigned [io 0x1000-0x1fff] [ 1.204592] pci 0000:01:00.0: BAR 1: assigned [mem 0x3046000000-0x304607ffff] [ 1.211790] pci 0000:01:00.0: BAR 6: assigned [mem 0x3046080000-0x30460bffff pref] [ 1.219408] pci 0000:01:00.0: BAR 0: assigned [mem 0x30460c0000-0x30460dffff] [ 1.226608] pci 0000:01:00.0: BAR 3: assigned [mem 0x30460e0000-0x30460e3fff] [ 1.233804] pci 0000:01:00.0: BAR 2: assigned [io 0x1000-0x101f] [ 1.239951] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 1.245209] pci 0000:00:00.0: bridge window [io 0x1000-0x1fff] [ 1.251344] pci 0000:00:00.0: bridge window [mem 0x3046000000-0x30460fffff] [ 1.258580] layerscape-pcie 3700000.pcie: host bridge /soc/pcie@3700000 ranges: [ 1.265942] layerscape-pcie 3700000.pcie: IO 0x3800010000..0x380001ffff -> 0x00000000 [ 1.274091] layerscape-pcie 3700000.pcie: MEM 0x3840000000..0x387fffffff -> 0x40000000 [ 1.282287] layerscape-pcie 3700000.pcie: PCI host bridge to bus 0001:00 [ 1.289033] pci_bus 0001:00: root bus resource [bus 00-ff] [ 1.294553] pci_bus 0001:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) [ 1.303572] pci_bus 0001:00: root bus resource [mem 0x3840000000-0x387fffffff] (bus address [0x40000000-0x7fffffff]) [ 1.314861] pci 0001:00:00.0: BAR 6: assigned [mem 0x3840000000-0x38400007ff pref] [ 1.322481] pci 0001:00:00.0: PCI bridge to [bus 01-ff] [ 1.328129] EINJ: ACPI disabled. [ 1.334415] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.341532] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 8, base_baud = 21875000) is a 16550A [ 1.350504] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 8, base_baud = 21875000) is a 16550A [ 1.359284] console [ttyS1] enabled [ 1.359284] console [ttyS1] enabled [ 1.366267] bootconsole [uart8250] disabled [ 1.366267] bootconsole [uart8250] disabled [ 1.374848] SuperH (H)SCI(F) driver initialized [ 1.379503] msm_serial: driver initialized [ 1.383774] arm-smmu: deprecated \"mmu-masters\" DT property in use; DMA API support unavailable [ 1.392679] arm-smmu 5000000.iommu: probing hardware configuration... [ 1.399121] arm-smmu 5000000.iommu: SMMUv2 with: [ 1.403736] arm-smmu 5000000.iommu: stage 1 translation [ 1.409045] arm-smmu 5000000.iommu: stage 2 translation [ 1.414354] arm-smmu 5000000.iommu: nested translation [ 1.419576] arm-smmu 5000000.iommu: non-coherent table walk [ 1.425232] arm-smmu 5000000.iommu: (IDR0.CTTW overridden by FW configuration) [ 1.432540] arm-smmu 5000000.iommu: stream matching with 128 register groups [ 1.439674] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) [ 1.446202] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 [ 1.452641] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA [ 1.459078] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA [ 1.469166] loop: module loaded [ 1.473066] ahci-qoriq 3200000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 1.482032] ahci-qoriq 3200000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst [ 1.492027] scsi host0: ahci-qoriq [ 1.495559] ata1: SATA max UDMA/133 mmio [mem 0x03200000-0x0320ffff] port 0x100 irq 94 [ 1.503546] ahci-qoriq 3210000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 1.512505] ahci-qoriq 3210000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst [ 1.522374] scsi host1: ahci-qoriq [ 1.525868] ata2: SATA max UDMA/133 mmio [mem 0x03210000-0x0321ffff] port 0x100 irq 95 [ 1.534857] tun: Universal TUN/TAP device driver, 1.6 [ 1.540181] thunder_xcv, ver 1.0 [ 1.543422] thunder_bgx, ver 1.0 [ 1.546655] nicpf, ver 1.0 [ 1.549501] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 1.555331] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 1.561636] e1000e 0000:01:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 1.627507] e1000e 0000:01:00.0 0000:01:00.0 (uninitialized): registered PHC clock [ 1.697018] e1000e 0000:01:00.0 eth0: (PCI Express:2.5GT/s:Width x1) 68:05:ca:36:8d:e8 [ 1.704942] e1000e 0000:01:00.0 eth0: Intel(R) PRO/1000 Network Connection [ 1.711829] e1000e 0000:01:00.0 eth0: MAC: 3, PHY: 8, PBA No: E46981-008 [ 1.718558] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 1.725519] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.731105] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 1.738934] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 1.744978] sky2: driver version 1.30 [ 1.748876] VFIO - User Level meta-driver version: 0.3 [ 1.754202] dwc3 3100000.usb3: Failed to get clk 'ref': -2 [ 1.759984] dwc3 3110000.usb3: Failed to get clk 'ref': -2 [ 1.766010] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.772542] ehci-pci: EHCI PCI platform driver [ 1.776999] ehci-platform: EHCI generic platform driver [ 1.782261] ehci-orion: EHCI orion driver [ 1.786298] ehci-exynos: EHCI EXYNOS driver [ 1.790508] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.796690] ohci-pci: OHCI PCI platform driver [ 1.801147] ohci-platform: OHCI generic platform driver [ 1.806402] ohci-exynos: OHCI EXYNOS driver [ 1.810724] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 1.816214] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 1.817246] ata1: SATA link down (SStatus 0 SControl 300) [ 1.824049] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 [ 1.838679] xhci-hcd xhci-hcd.0.auto: irq 96, io mem 0x03100000 [ 1.844864] hub 1-0:1.0: USB hub found [ 1.845225] ata2: SATA link down (SStatus 0 SControl 300) [ 1.848622] hub 1-0:1.0: 1 port detected [ 1.858026] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 1.863515] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 1.871171] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed [ 1.877715] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.885965] hub 2-0:1.0: USB hub found [ 1.889722] hub 2-0:1.0: 1 port detected [ 1.893769] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 1.899259] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 [ 1.907127] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 [ 1.916542] xhci-hcd xhci-hcd.1.auto: irq 97, io mem 0x03110000 [ 1.922681] hub 3-0:1.0: USB hub found [ 1.926437] hub 3-0:1.0: 1 port detected [ 1.930454] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 1.935939] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 [ 1.943595] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 1.950136] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.958380] hub 4-0:1.0: USB hub found [ 1.962137] hub 4-0:1.0: 1 port detected [ 1.966264] usbcore: registered new interface driver usb-storage [ 1.973194] i2c /dev entries driver [ 1.977657] i2c i2c-0: Added multiplexed i2c bus 1 [ 2.083105] rtc-ds3232: probe of 2-0068 failed with error -110 [ 2.088952] i2c i2c-0: Added multiplexed i2c bus 2 [ 2.093852] i2c i2c-0: Added multiplexed i2c bus 3 [ 2.098747] i2c i2c-0: Added multiplexed i2c bus 4 [ 2.103603] i2c i2c-0: Added multiplexed i2c bus 5 [ 2.108462] i2c i2c-0: Added multiplexed i2c bus 6 [ 2.113315] i2c i2c-0: Added multiplexed i2c bus 7 [ 2.118170] i2c i2c-0: Added multiplexed i2c bus 8 [ 2.122960] pca954x 0-0075: registered 8 multiplexed busses for I2C mux pca9547 [ 2.131123] sp805-wdt c000000.wdt: registration successful [ 2.136676] sp805-wdt c010000.wdt: registration successful [ 2.142221] sp805-wdt c100000.wdt: registration successful [ 2.147767] sp805-wdt c110000.wdt: registration successful [ 2.153314] sp805-wdt c200000.wdt: registration successful [ 2.158865] sp805-wdt c210000.wdt: registration successful [ 2.164409] sp805-wdt c300000.wdt: registration successful [ 2.169953] sp805-wdt c310000.wdt: registration successful [ 2.176049] sdhci: Secure Digital Host Controller Interface driver [ 2.182228] sdhci: Copyright(c) Pierre Ossman [ 2.186679] Synopsys Designware Multimedia Card Interface Driver [ 2.192963] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.224116] mmc0: SDHCI controller on 2140000.esdhc [2140000.esdhc] using ADMA 64-bit [ 2.232352] ledtrig-cpu: registered to indicate activity on CPUs [ 2.238753] usbcore: registered new interface driver usbhid [ 2.244324] usbhid: USB HID core driver [ 2.248754] optee: probing for conduit method from DT. [ 2.253891] optee: api uid mismatch [ 2.257808] NET: Registered protocol family 17 [ 2.262331] 9pnet: Installing 9P2000 support [ 2.266622] Key type dns_resolver registered [ 2.271163] registered taskstats version 1 [ 2.275260] Loading compiled-in X.509 certificates [ 2.280787] hctosys: unable to open rtc device (rtc0) [ 4.780069] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None [ 4.819086] Sending DHCP requests ..., OK [ 13.815105] IP-Config: Got DHCP answer from 172.16.1.4, my address is 172.16.1.171 [ 13.822676] IP-Config: Complete: [ 13.825900] device=eth0, hwaddr=68:05:ca:36:8d:e8, ipaddr=172.16.1.171, mask=255.255.255.0, gw=172.16.1.4 [ 13.835900] host=172.16.1.171, domain=example.org, nis-domain=(none) [ 13.842685] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= [ 13.842687] nameserver0=172.16.1.4 [ 13.852779] ALSA device list: [ 13.855747] No soundcards found. [ 13.859602] Freeing unused kernel memory: 1280K [ 13.864187] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: [ 13.893632] udevd[1547]: starting version 3.2.9 [ 13.898411] random: udevd: uninitialized urandom read (16 bytes read) [ 13.904929] random: udevd: uninitialized urandom read (16 bytes read) [ 13.911394] random: udevd: uninitialized urandom read (16 bytes read) [ 13.919793] udevd[1547]: specified user 'tss' unknown [ 13.924884] udevd[1547]: specified group 'tss' unknown [ 13.930643] udevd[1548]: starting eudev-3.2.9 [ 13.984866] ina2xx 3-0040: error configuring the device: -11 [ 13.984899] lm90 4-004c: 4-004c supply vcc not found, using dummy regulator [ 13.992011] udevd[1555]: Error changing net interface name eth0 to enp1s0: Device or resource busy [ 13.997552] lm90 4-004c: Linked as a consumer to regulator.0 [ 14.006521] udevd[1555]: could not rename interface '2' from 'eth0' to 'enp1s0': Device or resource busy [ 14.012333] lm90 4-004c: Failed to initialize device [ 14.026642] lm90 4-004c: Dropping the link to regulator.0 [ 14.032063] lm90: probe of 4-004c failed with error -11 done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: [ 14.084354] NET: Registered protocol family 10 [ 14.089561] Segment Routing with IPv6 OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1230805/environment . /lava-1230805/environment / # /lava-1230805/bin/lava-test-runner /lava-1230805/0 /lava-1230805/bin/lava-test-runner /lava-1230805/0 + export 'TESTRUN_[ 14.600089] ID=0_dmesg' + cd /lava-1230805/0/tests/0_dmesg + cat uuid + UUID=1230805_1.5.2.4.1 + set +x + KERNELCI_LAVA[ 14.614655] =y /bin/sh /opt/kernelci/dmesg.sh [ 14.631432] [ 14.647312] + [ 14.656177] set +x # / # #export SHELL=/bin/sh / # export SHELL=/bin/sh. /lava-1230805/environment / # . /lava-1230805/environment/lava-1230805/bin/lava-test-runner /lava-1230805/1 / # /lava-1230805/bin/lava-test-runner /lava-1230805/1 + export 'TESTRUN_[ 15.084510] ID=1_bootrr' + cd /lava-1230805/1/tests/1_bootrr + cat uuid + UUID=1230805_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/li[ 15.100216] bexec/bootrr/helpers:/lava-1230805/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/lib[ 15.116066] exec/bootrr + sh helpers/bootrr-auto /lava-123[ 15.128661] 0805/1/../bin/lava-test-case /lava-1230805/1/..[ 15.138855] /bin/lava-test-case /lava-1230805/1/../bin/lava-test-case + set +x / #