Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. RomBOOT AT91Bootstrap 3.7.2-rc2-dirty (Tue 14 Apr 02:17:07 BST 2015) NAND: ONFI not supported NAND: Manufacturer ID: 0xec Chip ID: 0xda NAND: Disable On-Die ECC NAND: Press the recovery button (BP4) to recovery NAND: Using Software ECC NAND: Image: Copy 0x80000 bytes from 0x40000 to 0x21f00000 NAND: Done to load image U-Boot 2015.01 (Apr 14 2015 - 16:45:04) CPU: AT91SAM9G20 Crystal frequency: 18.432 MHz CPU clock : 396.288 MHz Master clock : 132.096 MHz DRAM: 64 MiB WARNING: Caches not enabled NAND: 256 MiB MMC: mci: 0 In: serial Out: serial Err: serial Net: macb0 Hit any key to stop autoboot: 3  0 U-Boot> setenv autoload no setenv autoload no U-Boot> setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff U-Boot> setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff U-Boot> dhcp dhcp macb0: Starting autonegotiation... macb0: Autonegotiation complete macb0: link up, 100Mbps full-duplex (lpa: 0xc1e1) BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 BOOTP broadcast 4 BOOTP broadcast 5 *** Unhandled DHCP Option in OFFER/ACK: 42 *** Unhandled DHCP Option in OFFER/ACK: 42 DHCP client bound to address 192.168.56.20 (3793 ms) U-Boot> setenv serverip 192.168.56.230 setenv serverip 192.168.56.230 U-Boot> tftp 0x22100000 671917/tftp-deploy-iqblh3fe/kernel/zImage tftp 0x22100000 671917/tftp-deploy-iqblh3fe/kernel/zImage macb0: link up, 100Mbps full-duplex (lpa: 0xc1e1) Using macb0 device TFTP from server 192.168.56.230; our IP address is 192.168.56.20 Filename '671917/tftp-deploy-iqblh3fe/kernel/zImage'. Load address: 0x22100000 Loading: *####################################################################################################################################################################################################################################################################################### 1.2 MiB/s done Bytes transferred = 4141048 (3f2ff8 hex) U-Boot> tftp 0x23000000 671917/tftp-deploy-iqblh3fe/ramdisk/ramdisk.cpio.gz.uboot tftp 0x23000000 671917/tftp-deploy-iqblh3fe/ramdisk/ramdisk.cpio.gz.uboot macb0: link up, 100Mbps full-duplex (lpa: 0xc1e1) Using macb0 device TFTP from server 192.168.56.230; our IP address is 192.168.56.20 Filename '671917/tftp-deploy-iqblh3fe/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x23000000 Loading: *################################################################################################################################# ###################################################################################################################################################################################################### 1.2 MiB/s done Bytes transferred = 4856557 (4a1aed hex) U-Boot> setenv initrd_size ${filesize} setenv initrd_size ${filesize} U-Boot> tftp 0x22000000 671917/tftp-deploy-iqblh3fe/dtb/at91sam9g20ek.dtb tftp 0x22000000 671917/tftp-deploy-iqblh3fe/dtb/at91sam9g20ek.dtb macb0: link up, 100Mbps full-duplex (lpa: 0xc1e1) Using macb0 device TFTP from server 192.168.56.230; our IP address is 192.168.56.20 Filename '671917/tftp-deploy-iqblh3fe/dtb/at91sam9g20ek.dtb'. Load address: 0x22000000 Loading: *## 1.2 MiB/s done Bytes transferred = 20023 (4e37 hex) U-Boot> setenv bootargs ' root=/dev/nfs rw nfsroot=192.168.56.230:/var/lib/lava/dispatcher/tmp/671917/extract-nfsrootfs-b91oupuf,tcp,hard,vers=3 cma=0 ip=dhcp' setenv bootargs ' root=/dev/nfs rw nfsroot=192.168.56.230:/var/lib/lava/dispatcher/tmp/671917/extract-nfsrootfs-b91oupuf,tcp,hard,vers=3 cma=0 ip=dhcp' U-Boot> bootz 0x22100000 0x23000000 0x22000000 bootz 0x22100000 0x23000000 0x22000000 Kernel image @ 0x22100000 [ 0xinit Ramdisk from Legacy Image at 23000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 4856493 Bytes = 4.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 22000000 Booting using the fdt blob at 0x22000000 Using Device Tree in place at 22000000, end 22007e36 Starting kernel ... Booting Linux on physical CPU 0x0 Linux version 4.19.288-cip100 (KernelCI@build-j98490-arm-gcc-10-at91-dt-defconfig-dcgsg) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 Wed Jun 28 10:23:49 UTC 2023 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=0005317f CPU: VIVT data cache, VIVT instruction cache OF: fdt: Machine model: Atmel at91sam9g20ek Memory policy: Data cache writeback Built 1 zonelists, mobility grouping on. Total pages: 16256 Kernel command line: root=/dev/nfs rw nfsroot=192.168.56.230:/var/lib/lava/dispatcher/tmp/671917/extract-nfsrootfs-b91oupuf,tcp,hard,vers=3 cma=0 ip=dhcp Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 51704K/65536K availabl bss, 13832K reserved, 0K cma-reserved) Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xffc00000 - 0xfff00000 (3072 kB) vmalloc : 0xc4800000 - 0xff800000 ( 944 MB) lowmem : 0xc0000000 - 0xc4000000 ( 64 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .text : 0x(ptrval) - 0x(ptrval) (5713 kB) .init : 0x(ptrval) - 0x(ptrval) ( 240 kB) .data : 0x(ptrval) - 0x(ptrval) ( 188 kB) rval) ( 123 kB) NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 clocksource: pit: mask: 0x7ffffff max_cycles: 0x7ffffff, max_idle_ns: 7234361498 ns Console: colour dummy device 80x30 console [tty0] enabled sched_clock: 32 bits at 128 Hz, resolution 7812500ns, wraps every 16777215996093750ns Calibrating delay loop... 197.44 BogoMIPS (lpj=770048) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) CPU: Testing write buffer coherency: ok Setting up static identity map for 0x20008400 - 0x2000847c devtmpfs: initialized clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 14931722236523437 ns futex hash table entries: 256 (order: -1, 3072 bytes) pinctrl core: initialized pinctrl subsystem NET: Registered protocol family 16 DMA: preallocatedt allocations AT91: PM: standby: standby, suspend: ulp0 No ATAGs? gpio-at91 fffff400.gpio: at address (ptrval) gpio-at91 fffff600.gpio: at address (ptrval) gpio-at91 fffff800.gpio: at address (ptrval) pinctrl-at91 ahb:apb:pinctrl@fffff400: initialized AT91 pinctrl driver clocksource: tcb_clksrc: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 115749784805 ns AT91: Detected SoC: at91sam9g20, revision 1 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb i2c-gpio i2c-gpio-0: using lines 23 (SDA) and 24 (SCL) videodev: Linux video capture interface: v2.00 pps_core: Linuxore: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti PTP clock support registered Advanced Linux Sound Architecture Driver Initialized. clocksource: Switched to clocksource tcb_clksrc NET: Registered protocol family 2 IP idents hash table entries: 2048 (order: 2, 16384 bytes) tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes) TCP established hash table entries: 1024 (order: 0, 4096 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 1024 bind 1024) UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytmily 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. Trying to unpack rootfs image as initramfs... Freeing initrd memory: 4744K Initialise system trusted keyrings workingset: timestamp_bits=30 max_order=14 bucket_order=0 Key type asymmetric registered Asymmetric key parser 'x509' registered io sc) io scheduler mq-deadline registered io scheduler kyber registered fffff200.serial: ttyS0 at MMIO 0xfffff200 (irq = 16, base_baud = 8256000) is a ATMEL_SERIAL console [ttyS0] enabled fffb0000.serial: ttyS1 at MMIO 0xfffb0000 (irq = 26, base_baud = 8256000) is a ATMEL_SERIAL fffb4000.serial: ttyS2 at MMIO 0xfffb400) is a ATMEL_SERIAL brd: module loaded loop: module loaded ssc fffbc000.ssc: Atmel SSC device at 0x(ptrval) (irq 31) Davicom DM9161A fffc4000.ethernet-ffffffff:00: attached PHY driver [Davicom DM9161A] (mii_bus:phy_addr=fffc4000.ethernet-ffffffff:00, irq=POLL) macb fffc4000.ethernet eth0: Cadence MACB rev 0x0001010c at 0xfffc4000 irq 28 (a6:72:4e:7e:7a:f8) ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-atmel: EHCI Atmel driver ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ohci-atmel: OHCI Atmel dr Host Controller at91_ohci 500000.ohci: new USB bus registered, assigned bus number 1 at91_ohci 500000.ohci: irq 33, io mem 0x00500000 usb usb1: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: USB Host Controller usb usb1: Manufacturer: Linux 4.19.288-cip100 ohci_hcd usb usb1: SerialNumber: at91 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected usbcore: registered new interface driver cdc_acm cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters usbcore: registered new interface driver usb-storage usbcore: registered new interface driver usbserial_generic usbserial: USB Serial support registered for generic usbcore: registered new interface driver ftdi_sio usbserial: USB Serial support registered for FTDI USB Serial Device usbcore: registered new interface driver pl2303 usbserial: USB Serial support registered for pl2303 udc: at91_udc version 3 May 2006 g_serial gadget: Gadget Serial v2.4 g_serial gadget: g_serial ready rtc-at91sam9 fffffd20.rtc: rtc core: registered fffffd20.rtc as rtc0 rtc-at91sam9 fffffd20.rtc: rtc0: SET TIME! at91-reset fffffd00.rstc: Starting after general reset at91_wdt fffffd40.watchdog: watchdog is disabled at91_wdt: probe of fffffd40.watchdog failed with error -22 atmel_mci fffa8000.mmc: version: 0x210 atmel_mci fffa8000.mmc: using PDC atmel_mci fffa8000.mmc: Atmel MCI controller at 0xfffa8000 irq 30, 1 slots usbcore: registered new interface driver usbhid usbhid: USB HID core driver nand: device found, Manufacturer ID: 0xec, Chip ID: 0xda nand: Samsung NAND 256MiB 3,3V 8-bit nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 Bad block table found at page 131008, version 0x01 Bad block table found at page 130944, version 0x01 nand_read_bbt: bad block at 0x000006120000 nand_read_bbt: bad block at 0x00000d880000 8 fixed-partitions partitions found on MTD device atmel_nand Creating 8 MTD partitions on \"atmel_nand\": 0x000000000000-0x000000020000 : \"at91bootstrap\" 0x000000020000-0x000000060000 : \"barebox\" 0x000000060000-0x000000080000 : \"bareboxenv\" 0x000000080000-0x0000000a0000 : \"bareboxenv2\" 0x0000000a0000-0x0000000c0000 : \"oftree\" 0x0000000c0000-0x0000004c0000 : \"kernel\" 0x0000004c0000-0x000007cc0000 : \"rootfs\" 0x000007cc0000-0x000010000000 : \"data\" iio iio:device0: Resolution used: 10 bits iio iio:device0: not support touchscreen in the adc compatible string. wm8731 1-001b: Assuming static MCLK wm8731 1-001b: 1-001b supply AVDD not found, using dummy regulator wm8731 1-001b: Linked as a consumer to regulator.0 wm8731 1-001b: 1-001b supply HPVDD not found, using dummy regulator wm8731 1-001b: 1-001b supply DCVDD not found, using dummy regulator wm8731 1-001b: 1-001b sup regulator ssc fffbc000.ssc: ASoC: Failed to create component debugfs directory at91sam9g20ek-audio sound: wm8731-hifi <-> fffbc000.ssc mapping ok NET: Registered protocol family 10 Segment Routing with IPv6 sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver NET: Registered protocol family 17 Loading compiled-in X.509 certificates input: gpio_keys as /devices/platform/gpio_keys/input/input0 rtc-at91sam9 fffffd20.rtc: hctosys: unable to read the hardware clock IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready macb fffc4000.ethernet eth0: link up (100/Full) IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Sending DHCP requests ..., OK IP-Config: Got DHCP answer from 192.168.56.254, my address is 192.168.56.20 IP-Config: Complete::4e:7e:7a:f8, ipaddr=192.168.56.20, mask=255.255.255.0, gw=192.168.56.254 host=192.168.56.20, domain=mayfield.sirena.org.uk, nis-domain=(none) bootserver=192.168.56.254, rootserver=192.168.56.230, rootpath= nameserver0=192.168.56.254 ntpserver0=50.205.244.22, ntpserver1=85.199.214.99 cfg80211: Loading compiled-in X.509 certificates for regulatory database cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' ALSA device list: #0: wm8731 @ AT91SAMG20EK platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 cfg80211: failed to load regulatory.db Freeing unused kernel memory: 240K This architecture does not have kernel memory protection. Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u2 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. IP-Config: eth0 hardware address a6:72:4e:7e:7a:f8 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.56.254): address: 192.168.56.20 broadcast: 192.168.56.255 netmask: 255.255.255.0 gateway: 192.168.56.254 dns0 : 192.168.56.254 dns1 : 0.0.0.0 domain : mayfield.sirena.org.uk rootserver: 192.168.56.254 rootpath: filename : om ... done. Begin: Running /scripts/init-bottom ... systemd[1]: System time before build time, advancing clock. systemd[1]: Failed to find module 'autofs4' systemd[1]: Failed to mount tmpfs at /sys/fs/cgroup: No such file or directory systemd[1]: Failed to mount cgroup at /sys/fs/cgroup/systemd: No such file or directory [[0;1;31m!!!!!![0m] Failed to mount API filesystems. systemd[1]: Freezing execution. random: crng init done