[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.38 (5 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 11238443/tftp-deploy-729szkjn/kernel/zImage tftp 0x10000000 11238443/tftp-deploy-729szkjn/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.38 Filename '11238443/tftp-deploy-729szkjn/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 14.4 MiB/s done Bytes transferred = 8729088 (853200 hex) => tftp 0x14000000 11238443/tftp-deploy-729szkjn/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 11238443/tftp-deploy-729szkjn/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.38 Filename '11238443/tftp-deploy-729szkjn/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 14.3 MiB/s done Bytes transferred = 9408438 (8f8fb6 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 11238443/tftp-deploy-729szkjn/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 11238443/tftp-deploy-729szkjn/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.38 Filename '11238443/tftp-deploy-729szkjn/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 3.3 MiB/s done Bytes transferred = 41606 (a286 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/11238443/extract-nfsrootfs-0pwmyrso,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/11238443/extract-nfsrootfs-0pwmyrso,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x853200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 9408374 Bytes = 9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d285 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.290-cip101 (KernelCI@build-j6587-arm-gcc-10-multi-v7-defconfig-t59kk) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Tue Aug 8 23:43:12 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] percpu: Embedded 16 pages/cpu s36748 r8192 d20596 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/11238443/extract-nfsrootfs-0pwmyrso,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 942976K/1048576K available (12288K kernel code, 1597K rwdata, 4684K rodata, 2048K init, 394K bss, 40064K reserved, 65536K cma-reserved, 196608K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1598 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 395 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008444] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.021481] Console: colour dummy device 80x30 <6>[ 0.023363] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.033780] CPU: Testing write buffer coherency: ok <6>[ 0.038913] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.044211] pid_max: default: 32768 minimum: 301 <6>[ 0.049214] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.055978] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.064143] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.069881] Setting up static identity map for 0x10300000 - 0x103000a0 <6>[ 0.077585] rcu: Hierarchical SRCU implementation. <6>[ 0.084141] EFI services will not be available. <6>[ 0.086389] smp: Bringing up secondary CPUs ... <6>[ 0.091653] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.091659] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.103002] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.103009] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.114193] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.114199] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.124645] smp: Brought up 1 node, 4 CPUs <6>[ 0.128902] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.135319] CPU: All CPU(s) started in SVC mode. <6>[ 0.141264] devtmpfs: initialized <6>[ 0.151067] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.156522] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.166270] futex hash table entries: 1024 (order: 4, 65536 bytes) <6>[ 0.175836] pinctrl core: initialized pinctrl subsystem <6>[ 0.180112] DMI not present or invalid. <6>[ 0.183359] NET: Registered protocol family 16 <6>[ 0.190753] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.197414] cpuidle: using governor menu <6>[ 0.199416] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.214369] vdd1p1: supplied by regulator-dummy <6>[ 0.216840] vdd3p0: supplied by regulator-dummy <6>[ 0.221564] vdd2p5: supplied by regulator-dummy <6>[ 0.226395] vddarm: supplied by regulator-dummy <6>[ 0.231303] vddpu: supplied by regulator-dummy <6>[ 0.235739] vddsoc: supplied by regulator-dummy <6>[ 0.254443] No ATAGs? <6>[ 0.254591] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.262551] hw-breakpoint: maximum watchpoint size is 4 bytes. <4>[ 0.272025] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory <6>[ 0.278903] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver <6>[ 0.290781] Serial: AMBA PL011 UART driver <6>[ 0.294619] console [pstore-1] enabled <6>[ 0.296476] pstore: Registered ramoops as persistent store backend <6>[ 0.302726] ramoops: attached 0x10000@0x30000000, ecc: 0/0 <6>[ 0.331315] mxs-dma 110000.dma-apbh: initialized <6>[ 0.340814] vgaarb: loaded <5>[ 0.341751] SCSI subsystem initialized <6>[ 0.345343] usbcore: registered new interface driver usbfs <6>[ 0.350779] usbcore: registered new interface driver hub <6>[ 0.356301] usbcore: registered new device driver usb <6>[ 0.362788] i2c i2c-0: IMX I2C adapter registered <6>[ 0.366534] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.372633] i2c i2c-1: IMX I2C adapter registered <6>[ 0.377056] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.383002] i2c i2c-2: IMX I2C adapter registered <6>[ 0.387588] i2c i2c-2: can't use DMA, using PIO instead. <6>[ 0.394688] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.398363] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.407771] PTP clock support registered <6>[ 0.412153] EDAC MC: Ver: 3.0.0 <6>[ 0.418139] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.481941] NET: Registered protocol family 2 <6>[ 0.484152] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.491687] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) <6>[ 0.498658] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.505976] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) <6>[ 0.512752] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.519433] UDP hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.525418] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.532177] NET: Registered protocol family 1 <6>[ 0.537151] RPC: Registered named UNIX socket transport module. <6>[ 0.542814] RPC: Registered udp transport module. <6>[ 0.547741] RPC: Registered tcp transport module. <6>[ 0.552718] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.559885] Trying to unpack rootfs image as initramfs... <6>[ 1.285340] Freeing initrd memory: 9188K <4>[ 1.287196] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 1.294382] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 1.304406] Initialise system trusted keyrings <6>[ 1.307390] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 1.319990] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.323864] NFS: Registering the id_resolver key type <5>[ 1.328606] Key type id_resolver registered <5>[ 1.332978] Key type id_legacy registered <6>[ 1.337280] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 1.344151] Key type asymmetric registered <5>[ 1.346206] Asymmetric key parser 'x509' registered <6>[ 1.351404] bounce: pool size: 64 pages <6>[ 1.355458] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 1.363100] io scheduler noop registered <6>[ 1.367258] io scheduler deadline registered <6>[ 1.371925] io scheduler cfq registered (default) <6>[ 1.376742] io scheduler mq-deadline registered <6>[ 1.381541] io scheduler kyber registered <6>[ 1.407702] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 1.412247] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 1.419364] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 1.426648] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 1.446820] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set <6>[ 1.450254] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc <4>[ 1.458034] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set <6>[ 1.464269] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 <4>[ 1.472126] PU : no governor for states <4>[ 1.472214] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 1.476090] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc <6>[ 1.485853] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 1.559008] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 1.566319] SuperH (H)SCI(F) driver initialized <6>[ 1.569215] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX <6>[ 1.577894] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX <6>[ 1.588907] console [ttymxc1] enabled <6>[ 1.588907] console [ttymxc1] enabled <6>[ 1.593889] bootconsole [ec_imx21] disabled <6>[ 1.593889] bootconsole [ec_imx21] disabled <6>[ 1.604000] msm_serial: driver initialized <6>[ 1.610260] STMicroelectronics ASC driver initialized <6>[ 1.617412] STM32 USART driver initialized <4>[ 1.632617] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 1.641326] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 1.648308] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 1.655059] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 1.664094] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 1.671264] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 1.685893] brd: module loaded <6>[ 1.698820] loop: module loaded <6>[ 1.705455] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 1.713677] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 1.721964] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 1.730436] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <6>[ 1.741215] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 1.748504] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 1.757563] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 1.768455] scsi host0: ahci-imx <6>[ 1.772525] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 <6>[ 1.791626] CAN device driver interface <6>[ 1.797003] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 1.804106] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator <6>[ 1.813088] fec 2188000.ethernet: Linked as a consumer to regulator.0 <6>[ 1.822184] pps pps0: new PPS source ptp0 <6>[ 1.843659] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 1.851107] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 1.857207] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 1.863470] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 1.870712] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.882488] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 1.890213] usbcore: registered new interface driver pegasus <6>[ 1.896178] usbcore: registered new interface driver asix <6>[ 1.901892] usbcore: registered new interface driver ax88179_178a <6>[ 1.908306] usbcore: registered new interface driver cdc_ether <6>[ 1.914456] usbcore: registered new interface driver smsc75xx <6>[ 1.920536] usbcore: registered new interface driver smsc95xx <6>[ 1.926582] usbcore: registered new interface driver net1080 <6>[ 1.932554] usbcore: registered new interface driver cdc_subset <6>[ 1.938786] usbcore: registered new interface driver zaurus <6>[ 1.944698] usbcore: registered new interface driver cdc_ncm <6>[ 1.953570] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 1.960394] ehci-pci: EHCI PCI platform driver <6>[ 1.965145] ehci-platform: EHCI generic platform driver <6>[ 1.970951] ehci-orion: EHCI orion driver <6>[ 1.975448] SPEAr-ehci: EHCI SPEAr driver <6>[ 1.979945] ehci-st: EHCI STMicroelectronics driver <6>[ 1.985284] ehci-exynos: EHCI EXYNOS driver <6>[ 1.989937] ehci-atmel: EHCI Atmel driver <6>[ 1.994390] tegra-ehci: Tegra EHCI driver <6>[ 1.998920] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 2.005382] ohci-pci: OHCI PCI platform driver <6>[ 2.010150] ohci-platform: OHCI generic platform driver <6>[ 2.015902] SPEAr-ohci: OHCI SPEAr driver <6>[ 2.020391] ohci-st: OHCI STMicroelectronics driver <6>[ 2.025720] ohci-atmel: OHCI Atmel driver <6>[ 2.031018] usbcore: registered new interface driver usb-storage <6>[ 2.039623] imx_usb 2184000.usb: Linked as a consumer to regulator.9 <6>[ 2.051637] imx_usb 2184200.usb: Linked as a consumer to regulator.14 <6>[ 2.061790] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 2.066975] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 2.098164] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 2.104478] hub 1-0:1.0: USB hub found <6>[ 2.108560] hub 1-0:1.0: 1 port detected <6>[ 2.109584] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 2.118466] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 2.119081] i2c /dev entries driver <6>[ 2.125004] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 2.143369] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) <6>[ 2.154837] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.161303] sdhci: Copyright(c) Pierre Ossman <6>[ 2.168235] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.176517] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.183323] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO <6>[ 2.188783] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO <6>[ 2.194283] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.234138] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA <6>[ 2.242161] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO <6>[ 2.247668] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.287626] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA <6>[ 2.299198] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 2.306288] usbcore: registered new interface driver usbhid <6>[ 2.312192] usbhid: USB HID core driver <6>[ 2.322346] NET: Registered protocol family 10 <6>[ 2.323225] mmc0: new high speed SDHC card at address aaaa <6>[ 2.328218] Segment Routing with IPv6 <6>[ 2.334543] mmcblk0: mmc0:aaaa SL16G 14.8 GiB <6>[ 2.336822] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.348360] NET: Registered protocol family 17 <6>[ 2.353084] can: controller area network core (rev 20170425 abi 9) <6>[ 2.359628] NET: Registered protocol family 29 <6>[ 2.364343] can: raw protocol (rev 20170425) <6>[ 2.368900] can: broadcast manager protocol (rev 20170425 t) <6>[ 2.374833] can: netlink gateway (rev 20170425) max_hops=1 <5>[ 2.381113] Key type dns_resolver registered <6>[ 2.386729] cpu cpu0: Linked as a consumer to regulator.4 <6>[ 2.392498] cpu cpu0: Linked as a consumer to regulator.5 <6>[ 2.398180] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 2.404982] cpu cpu0: Linked as a consumer to regulator.6 <6>[ 2.411490] ThumbEE CPU extension supported. <5>[ 2.416069] Registering SWP/SWPB emulation handler <5>[ 2.422170] Loading compiled-in X.509 certificates <6>[ 2.429105] pstore: Using compression: deflate <6>[ 2.447507] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.454922] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.463496] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.471114] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.479818] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.488508] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.495627] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.503527] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.512567] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.519816] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.528517] imx_thermal tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 2.538361] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 2.546022] GPT:29296874 != 31116287 <4>[ 2.549888] GPT:Alternate GPT header not at the end of the disk. <4>[ 2.556158] GPT:29296874 != 31116287 <4>[ 2.560015] GPT: Use GNU Parted to correct GPT errors. <6>[ 2.565453] mmcblk0: p1 p2 p3 <6>[ 2.569740] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.577096] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.585456] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.593059] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.601694] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.610385] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.618972] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.626892] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.635930] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.645158] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.652937] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.660464] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.668732] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.676305] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.684877] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.693569] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.700625] hub 1-1:1.0: USB hub found <6>[ 2.704713] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 2.711803] hub 1-1:1.0: 3 ports detected <4>[ 2.716908] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.725947] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.733166] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.740908] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.748308] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.756476] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.764097] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.772619] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.781294] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.788268] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 2.796653] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <4>[ 2.804313] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.813378] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.820516] hctosys: unable to open rtc device (rtc0) <6>[ 2.820524] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.834079] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.841481] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.849802] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.857245] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.865805] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.874483] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.881432] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.889224] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.898265] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.905372] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.948589] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 2.963576] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 6.078779] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 6.088223] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 6.118209] Sending DHCP requests ., OK <6>[ 6.162442] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.38 <6>[ 6.170785] IP-Config: Complete: <6>[ 6.174303] device=eth0, hwaddr=00:19:b8:08:f0:fe, ipaddr=192.168.201.38, mask=255.255.255.0, gw=192.168.201.1 <6>[ 6.185058] host=imx6q-sabrelite-lava-cbg-8, domain=lava-rack, nis-domain=(none) <6>[ 6.193200] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 6.193210] nameserver0=192.168.201.1 <6>[ 6.212398] Freeing unused kernel memory: 2048K <6>[ 6.228562] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u2 <6>[ 7.041737] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.050089] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.050659] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.064250] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 <6>[ 7.072196] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) <6>[ 7.073023] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.080254] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.096436] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 7.097131] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <4>[ 7.105509] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.110451] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 7.119130] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.132563] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.140854] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.149936] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.157104] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.165283] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.172755] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.181451] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.189031] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 7.223388] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <4>[ 7.223972] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.233063] sgtl5000 0-000a: Linked as a consumer to regulator.7 <6>[ 7.244753] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.251880] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 7.261111] sgtl5000 0-000a: Linked as a consumer to regulator.8 <4>[ 7.267629] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.276926] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.285099] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.289600] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 7.293285] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.298302] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 7.312395] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.319847] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 7.321204] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.329292] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 0 <6>[ 7.332600] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.350440] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.359265] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.366349] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 7.373978] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <4>[ 7.374878] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.390940] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.398210] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.406584] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.414066] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.423099] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.430678] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.469365] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.478208] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.490547] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.499303] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.508423] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.515716] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.523927] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.531384] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.540502] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.548017] pwm-backlight backlight-lvds: Dropping the link to regulator.8 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. IP-Config: eth0 hardware address 00:19:b8:08:f0:fe mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.38 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-8 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 8.562281] systemd[1]: System time before build time, advancing clock. <3>[ 8.593716] cgroup: cgroup2: unknown option "memory_recursiveprot" <30>[ 8.609336] systemd[1]: systemd 247.3-7+deb11u2 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 8.634253] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! <30>[ 8.670672] systemd[1]: Set hostname to . <30>[ 9.447019] systemd[1]: Queued start job for default target Graphical Interface. <5>[ 9.456896] random: systemd: uninitialized urandom read (16 bytes read) <28>[ 9.463985] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. <28>[ 9.476796] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) <30>[ 9.486308] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. <5>[ 9.518558] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 9.526588] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. <5>[ 9.568476] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 9.576477] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. <30>[ 9.619300] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. <30>[ 9.658651] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. <30>[ 9.698998] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. <30>[ 9.738765] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 9.751286] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. <30>[ 9.789098] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. <30>[ 9.818718] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. <30>[ 9.858603] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. <30>[ 9.888739] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. <30>[ 9.919596] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. <30>[ 9.992920] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. <30>[ 10.002766] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). <30>[ 10.039946] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. <30>[ 10.080542] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. <30>[ 10.121540] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. <30>[ 10.159770] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. <30>[ 10.199677] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 10.209274] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. <30>[ 10.221806] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... <30>[ 10.262585] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... <30>[ 10.302903] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... <30>[ 10.341921] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... <30>[ 10.381924] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... <30>[ 10.423468] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... <30>[ 10.460792] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. <5>[ 10.471115] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 10.481323] systemd[1]: Starting Journal Service... Starting Journal Service... <5>[ 10.522765] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 10.532670] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... <5>[ 10.568515] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 10.578342] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... <30>[ 10.621400] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... <30>[ 10.663742] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. <30>[ 10.699010] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. <30>[ 10.739582] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. <30>[ 10.795892] systemd[1]: modprobe@configfs.service: Succeeded. <30>[ 10.802811] systemd[1]: Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module configfs. <30>[ 10.838997] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... <46>[ 11.107193] systemd-journald[162]: Received client request to flush runtime journal. Starting Apply Kernel Variables... Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. <5>[ 11.509003] random: systemd: uninitialized urandom read (16 bytes read) Starting Create Static Device Nodes in /dev... <5>[ 11.588607] random: systemd-journal: uninitialized urandom read (16 bytes read) [ OK ] Finished Flush Journa<5>[ 11.600470] random: systemd-journal: uninitialized urandom read (16 bytes read) l to Persistent Storage. [ OK ] Finished Coldplug All udev Devices. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... <5>[ 12.108211] random: crng init done <5>[ 12.111906] random: 48 urandom warning(s) missed due to ratelimiting [ OK ] Finished Load/Save Random Seed. [ OK ] Started Rule-based Manager for Device Events and Files. [ OK ] Finished Create Volatile Files and Directories. Starting Network Service... Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Found device /dev/ttymxc1. [ OK ] Started Network Name Resolution. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 4.19.290-cip101 #1 SMP Tue Aug 8 23:43:12 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/11238443/extract-nfsrootfs-0pwmyrso' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/11238443/extract-nfsrootfs-0pwmyrso' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-11238443/environment . /lava-11238443/environment / # /lava-11238443/bin/lava-test-runner /lava-11238443/0 /lava-11238443/bin/lava-test-runner /lava-11238443/0 + export TESTRUN_ID=0_dmesg + cd /lava-11238443/0/tests/0_dmesg + cat uuid + UUID=11238443_1.6.2.4.1 + set +<8>[ 24.743925] x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 24.835883] <8>[ 24.895092] <8>[ 24.953895] + set +x <8>[ 24.963439] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-11238443/environment / # . /lava-11238443/environment/lava-11238443/bin/lava-test-runner /lava-11238443/1 / # /lava-11238443/bin/lava-test-runner /lava-11238443/1 + export TESTRUN_ID=1_bootrr + cd /lava-11238443/1/tests/1_bootrr + cat uuid + UUID=11238443_1.6.2.4.5 + <8>[ 25.512992] set +x + export PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-11238443/1/../bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto panel-lcd panel-lvds0 backlight-lcd backlight-lvds /lava-11238443/1/../bin/lava-test-case <8>[ 26.646949] /lava-11238443/1/../bin/lava-test-case <8>[ 26.716600] /lava-11238443/1/../bin/lava-test-case <8>[ 26.755246] + set +x <8>[ 26.782649] / #