[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.0 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected sst25vf016b with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 6 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.191 (5 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 11304000/tftp-deploy-rgkcno4w/kernel/zImage tftp 0x10000000 11304000/tftp-deploy-rgkcno4w/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.191 Filename '11304000/tftp-deploy-rgkcno4w/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 3.5 MiB/s done Bytes transferred = 8733184 (854200 hex) => tftp 0x14000000 11304000/tftp-deploy-rgkcno4w/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 11304000/tftp-deploy-rgkcno4w/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.191 Filename '11304000/tftp-deploy-rgkcno4w/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################ 2.9 MiB/s done Bytes transferred = 13338066 (cb85d2 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 11304000/tftp-deploy-rgkcno4w/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 11304000/tftp-deploy-rgkcno4w/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.191 Filename '11304000/tftp-deploy-rgkcno4w/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 2.2 MiB/s done Bytes transferred = 41818 (a35a hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x854200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 13338002 Bytes = 12.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d359 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.292-cip101 (KernelCI@build-j15981-arm-gcc-10-multi-v7-defconfig-qtqwf) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Wed Aug 16 23:04:37 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] percpu: Embedded 16 pages/cpu s36748 r8192 d20596 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 939136K/1048576K available (12288K kernel code, 1597K rwdata, 4684K rodata, 2048K init, 394K bss, 43904K reserved, 65536K cma-reserved, 196608K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1598 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 395 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 15ns <6>[ 0.000007] sched_clock: 32 bits at 66MHz, resolution 15ns, wraps every 32537631224ns <6>[ 0.008093] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 28958491609 ns <6>[ 0.020998] Console: colour dummy device 80x30 <6>[ 0.022879] Calibrating delay loop (skipped), value calculated using timer frequency.. 132.00 BogoMIPS (lpj=660000) <6>[ 0.033558] CPU: Testing write buffer coherency: ok <6>[ 0.038690] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.043988] pid_max: default: 32768 minimum: 301 <6>[ 0.048993] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.055745] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.063928] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.069664] Setting up static identity map for 0x10300000 - 0x103000a0 <6>[ 0.077380] rcu: Hierarchical SRCU implementation. <6>[ 0.083939] EFI services will not be available. <6>[ 0.086189] smp: Bringing up secondary CPUs ... <6>[ 0.091458] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.091465] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.102802] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.102807] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.113993] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.113998] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.124447] smp: Brought up 1 node, 4 CPUs <6>[ 0.128701] SMP: Total of 4 processors activated (528.00 BogoMIPS). <6>[ 0.135204] CPU: All CPU(s) started in SVC mode. <6>[ 0.141158] devtmpfs: initialized <6>[ 0.150861] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.156313] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.166065] futex hash table entries: 1024 (order: 4, 65536 bytes) <6>[ 0.175593] pinctrl core: initialized pinctrl subsystem <6>[ 0.179900] DMI not present or invalid. <6>[ 0.183124] NET: Registered protocol family 16 <6>[ 0.190548] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.197202] cpuidle: using governor menu <6>[ 0.199199] CPU identified as i.MX6Q, silicon rev 1.0 <6>[ 0.214092] vdd1p1: supplied by regulator-dummy <6>[ 0.216561] vdd3p0: supplied by regulator-dummy <6>[ 0.221295] vdd2p5: supplied by regulator-dummy <6>[ 0.226133] vddarm: supplied by regulator-dummy <6>[ 0.231043] vddpu: supplied by regulator-dummy <6>[ 0.235443] vddsoc: supplied by regulator-dummy <6>[ 0.253995] No ATAGs? <6>[ 0.254142] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.262101] hw-breakpoint: maximum watchpoint size is 4 bytes. <4>[ 0.271546] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory <6>[ 0.278427] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver <6>[ 0.290250] Serial: AMBA PL011 UART driver <6>[ 0.294030] console [pstore-1] enabled <6>[ 0.295926] pstore: Registered ramoops as persistent store backend <6>[ 0.302195] ramoops: attached 0x10000@0x30000000, ecc: 0/0 <6>[ 0.330630] mxs-dma 110000.dma-apbh: initialized <6>[ 0.340091] vgaarb: loaded <5>[ 0.341012] SCSI subsystem initialized <6>[ 0.344612] usbcore: registered new interface driver usbfs <6>[ 0.350036] usbcore: registered new interface driver hub <6>[ 0.355551] usbcore: registered new device driver usb <6>[ 0.362123] i2c i2c-0: IMX I2C adapter registered <6>[ 0.365789] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.371935] i2c i2c-1: IMX I2C adapter registered <6>[ 0.376333] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.382273] i2c i2c-2: IMX I2C adapter registered <6>[ 0.386862] i2c i2c-2: can't use DMA, using PIO instead. <6>[ 0.393948] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.397640] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.407048] PTP clock support registered <6>[ 0.411430] EDAC MC: Ver: 3.0.0 <6>[ 0.417386] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.481304] NET: Registered protocol family 2 <6>[ 0.483503] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.491048] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) <6>[ 0.498016] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.505335] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) <6>[ 0.512125] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.518796] UDP hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.524781] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.531545] NET: Registered protocol family 1 <6>[ 0.536527] RPC: Registered named UNIX socket transport module. <6>[ 0.542175] RPC: Registered udp transport module. <6>[ 0.547103] RPC: Registered tcp transport module. <6>[ 0.552089] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.559230] Trying to unpack rootfs image as initramfs... <6>[ 1.674303] Freeing initrd memory: 13028K <4>[ 1.676263] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 1.683503] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 1.693457] Initialise system trusted keyrings <6>[ 1.696496] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 1.708954] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.712823] NFS: Registering the id_resolver key type <5>[ 1.717571] Key type id_resolver registered <5>[ 1.721942] Key type id_legacy registered <6>[ 1.726244] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 1.733110] Key type asymmetric registered <5>[ 1.735169] Asymmetric key parser 'x509' registered <6>[ 1.740369] bounce: pool size: 64 pages <6>[ 1.744423] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 1.752064] io scheduler noop registered <6>[ 1.756220] io scheduler deadline registered <6>[ 1.760890] io scheduler cfq registered (default) <6>[ 1.765705] io scheduler mq-deadline registered <6>[ 1.770506] io scheduler kyber registered <6>[ 1.796484] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 1.801026] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 1.808144] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 1.815431] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 1.835550] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set <6>[ 1.838978] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc <4>[ 1.846762] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set <6>[ 1.853015] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 <4>[ 1.860900] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <4>[ 1.867404] PU : no governor for states <6>[ 1.870498] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 1.874563] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc <6>[ 1.946439] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 1.953757] SuperH (H)SCI(F) driver initialized <6>[ 1.956609] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX <6>[ 1.965364] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX <6>[ 1.976333] console [ttymxc1] enabled <6>[ 1.976333] console [ttymxc1] enabled <6>[ 1.981334] bootconsole [ec_imx21] disabled <6>[ 1.981334] bootconsole [ec_imx21] disabled <6>[ 1.991438] msm_serial: driver initialized <6>[ 1.997679] STMicroelectronics ASC driver initialized <6>[ 2.004811] STM32 USART driver initialized <4>[ 2.020036] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.028735] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.035694] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.042483] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.051515] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.058683] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.073347] brd: module loaded <6>[ 2.083404] loop: module loaded <6>[ 2.090050] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 2.098286] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 2.106560] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 2.115020] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <6>[ 2.125803] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 2.133089] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 2.142177] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 2.152950] scsi host0: ahci-imx <6>[ 2.156995] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 <6>[ 2.175946] CAN device driver interface <6>[ 2.181333] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 2.188432] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator <6>[ 2.197390] fec 2188000.ethernet: Linked as a consumer to regulator.0 <6>[ 2.206476] pps pps0: new PPS source ptp0 <6>[ 2.237119] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 2.244545] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 2.250675] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.256915] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 2.264161] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 2.275841] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 2.283571] usbcore: registered new interface driver pegasus <6>[ 2.289554] usbcore: registered new interface driver asix <6>[ 2.295250] usbcore: registered new interface driver ax88179_178a <6>[ 2.301669] usbcore: registered new interface driver cdc_ether <6>[ 2.307832] usbcore: registered new interface driver smsc75xx <6>[ 2.313886] usbcore: registered new interface driver smsc95xx <6>[ 2.319948] usbcore: registered new interface driver net1080 <6>[ 2.325902] usbcore: registered new interface driver cdc_subset <6>[ 2.332134] usbcore: registered new interface driver zaurus <6>[ 2.338065] usbcore: registered new interface driver cdc_ncm <6>[ 2.346885] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 2.353715] ehci-pci: EHCI PCI platform driver <6>[ 2.358482] ehci-platform: EHCI generic platform driver <6>[ 2.364260] ehci-orion: EHCI orion driver <6>[ 2.368790] SPEAr-ehci: EHCI SPEAr driver <6>[ 2.373258] ehci-st: EHCI STMicroelectronics driver <6>[ 2.378631] ehci-exynos: EHCI EXYNOS driver <6>[ 2.383267] ehci-atmel: EHCI Atmel driver <6>[ 2.387742] tegra-ehci: Tegra EHCI driver <6>[ 2.392238] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 2.398718] ohci-pci: OHCI PCI platform driver <6>[ 2.403474] ohci-platform: OHCI generic platform driver <6>[ 2.409246] SPEAr-ohci: OHCI SPEAr driver <6>[ 2.413714] ohci-st: OHCI STMicroelectronics driver <6>[ 2.419061] ohci-atmel: OHCI Atmel driver <6>[ 2.424328] usbcore: registered new interface driver usb-storage <6>[ 2.432914] imx_usb 2184000.usb: Linked as a consumer to regulator.9 <6>[ 2.444964] imx_usb 2184200.usb: Linked as a consumer to regulator.14 <6>[ 2.455156] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 2.460345] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 2.488964] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 2.494661] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 2.497415] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 2.501222] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 2.507569] hub 1-0:1.0: USB hub found <6>[ 2.518319] hub 1-0:1.0: 1 port detected <6>[ 2.528779] i2c /dev entries driver <3>[ 2.543712] imx_thermal tempmon: invalid sensor calibration data <3>[ 2.550021] imx_thermal tempmon: failed to init from from fsl,tempmon-data <4>[ 2.557174] imx_thermal: probe of tempmon failed with error -22 <6>[ 2.566600] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) <6>[ 2.578096] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.584543] sdhci: Copyright(c) Pierre Ossman <6>[ 2.591420] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.599691] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.606486] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO <6>[ 2.611940] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO <6>[ 2.617455] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.657246] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA <6>[ 2.665290] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO <6>[ 2.670844] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.710757] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA <6>[ 2.722144] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 2.729444] usbcore: registered new interface driver usbhid <6>[ 2.735283] usbhid: USB HID core driver <6>[ 2.745312] NET: Registered protocol family 10 <6>[ 2.751270] Segment Routing with IPv6 <6>[ 2.755294] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.762077] NET: Registered protocol family 17 <6>[ 2.766818] can: controller area network core (rev 20170425 abi 9) <6>[ 2.773386] NET: Registered protocol family 29 <6>[ 2.774364] mmc0: new high speed SDHC card at address 0001 <6>[ 2.778123] can: raw protocol (rev 20170425) <6>[ 2.785545] mmcblk0: mmc0:0001 SD 14.8 GiB <6>[ 2.788443] can: broadcast manager protocol (rev 20170425 t) <6>[ 2.788464] can: netlink gateway (rev 20170425) max_hops=1 <5>[ 2.805109] Key type dns_resolver registered <6>[ 2.810504] cpu cpu0: Linked as a consumer to regulator.4 <6>[ 2.816245] cpu cpu0: Linked as a consumer to regulator.5 <6>[ 2.821988] cpu cpu0: Linked as a consumer to regulator.6 <6>[ 2.827412] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 2.828493] ThumbEE CPU extension supported. <5>[ 2.838956] Registering SWP/SWPB emulation handler <5>[ 2.844833] Loading compiled-in X.509 certificates <6>[ 2.851733] pstore: Using compression: deflate <4>[ 2.858994] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 2.866671] GPT:7812499 != 30965759 <4>[ 2.870496] GPT:Alternate GPT header not at the end of the disk. <6>[ 2.871914] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <4>[ 2.876779] GPT:7812499 != 30965759 <4>[ 2.876788] GPT: Use GNU Parted to correct GPT errors. <6>[ 2.884195] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.887931] mmcblk0: p1 p2 p3 <6>[ 2.894987] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.911141] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.920172] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.928876] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.935828] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.943923] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.952956] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.960089] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.967990] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.975352] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.983712] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.991183] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.000023] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.008720] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.015666] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.023681] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.032710] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.039848] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.046891] hub 1-1:1.0: USB hub found <6>[ 3.047810] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.051017] hub 1-1:1.0: 3 ports detected <6>[ 3.058295] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.070965] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.078445] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.087236] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.095924] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.102894] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.110904] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.119936] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.127053] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.134905] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.142292] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.151518] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 3.158513] hctosys: unable to open rtc device (rtc0) <6>[ 3.165203] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.172754] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.181823] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.190522] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.197497] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.205607] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.214645] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.221789] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.229701] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.237066] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.278300] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:06: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:06, irq=POLL) <6>[ 3.293242] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 5.357998] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 5.367465] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 5.397542] Sending DHCP requests ., OK <6>[ 5.441622] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.191 <6>[ 5.450043] IP-Config: Complete: <6>[ 5.453561] device=eth0, hwaddr=0e:cc:7b:b0:7c:c7, ipaddr=192.168.201.191, mask=255.255.255.0, gw=192.168.201.1 <6>[ 5.464401] host=192.168.201.191, domain=lava-rack, nis-domain=(none) <6>[ 5.471592] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 5.471600] nameserver0=192.168.201.1 <6>[ 5.490286] Freeing unused kernel memory: 2048K <6>[ 5.518246] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 5.655768] udevd[107]: starting version 3.2.9 <5>[ 5.661597] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 5.668621] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 5.675443] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 5.691055] udevd[107]: specified user 'tss' unknown <27>[ 5.696522] udevd[107]: specified group 'tss' unknown <30>[ 5.704583] udevd[108]: starting eudev-3.2.9 <6>[ 6.064105] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 6.072559] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 6.082232] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 6.090980] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 6.102736] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 6.109712] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 <6>[ 6.114084] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 6.117618] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) <4>[ 6.118120] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 6.118186] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 6.118297] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 6.119672] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 6.124204] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 6.149874] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 6.166538] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 6.206100] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 6.216031] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 6.218480] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 6.222653] sgtl5000 0-000a: Linked as a consumer to regulator.7 <6>[ 6.222738] sgtl5000 0-000a: Linked as a consumer to regulator.8 <6>[ 6.224777] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 6.231536] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 6.242763] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 6.244445] sgtl5000 0-000a: sgtl5000 revision 0x11 <4>[ 6.253098] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 6.265721] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 6.269370] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 6.293450] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 6.302145] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 6.309592] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 6.318845] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 6.326331] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 6.336083] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 6.344833] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 6.351857] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 6.360776] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 6.370026] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 6.377217] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 6.385927] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 6.393380] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 6.403424] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 6.410947] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 6.448746] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 6.483921] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 6.490443] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 6.501102] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 0 <4>[ 6.511029] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 6.519829] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 6.528037] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 6.536547] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 6.545656] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 6.552970] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 6.561602] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 6.569068] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 6.578360] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 6.585854] pwm-backlight backlight-lvds: Dropping the link to regulator.8 done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 6.757702] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-11304000/environment . /lava-11304000/environment / # /lava-11304000/bin/lava-test-runner /lava-11304000/0 /lava-11304000/bin/lava-test-runner /lava-11304000/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-11304000/0/tests/0_dmesg + cat uuid + UUID=11304000_1.5.2.4.1 <8>[ 7.386533] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 7.445272] <8>[ 7.485344] <8>[ 7.536699] + set +x <8>[ 7.547703] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-11304000/environment / # . /lava-11304000/environment/lava-11304000/bin/lava-test-runner /lava-11304000/1 / # /lava-11304000/bin/lava-test-runner /lava-11304000/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-11304000/1/tests/1_bootrr + cat uuid + UUID=1130400<8>[ 8.078861] 0_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-11304000/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto panel-lcd panel-lvds0 backlight-lcd backlight-lvds /lava-11304000/1/../bin/lava-test-case <8>[ 9.164806] /lava-11304000/1/../bin/lava-test-case <8>[ 9.219093] /lava-11304000/1/../bin/lava-test-case <8>[ 9.244178] + set +x <8>[ 9.262694] / #