Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. NOTICE: UDIMM 18ASF1G72AZ-2G1A1 NOTICE: 16 GB DDR4, 64-bit, CL=13, ECC on, 256B, CS0+CS1 NOTICE: UDIMM 18ASF1G72AZ-2G1A1 NOTICE: 4 GB DDR4, 32-bit, CL=11, ECC on, CS0+CS1 NOTICE: BL2: v1.5(release):LSDK-19.06 NOTICE: BL2: Built : 21:37:56, Jul 29 2019 NOTICE: BL2: Booting BL31NOTICE: BL31: v1.5(release):LSDK-19.06 NOTICE: BL31: Built : 21:38:04, Jul 29 2019 NOTICE: Welcome to LS2088 BL31 Phase U-Boot 2019.04-gcbd7e30bf8 (Jul 29 2019 - 21:37:23 +0800) SoC: LS2088AE Rev1.0 (0x87090010) Clock Configuration: CPU0(A72):1800 MHz CPU1(A72):1800 MHz CPU2(A72):1800 MHz CPU3(A72):1800 MHz CPU4(A72):1800 MHz CPU5(A72):1800 MHz CPU6(A72):1800 MHz CPU7(A72):1800 MHz Bus: 700 MHz DDR: 1866.667 MT/s DP-DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 483038b8 48480048 00000000 00000000 00000010: 00000000 00000000 00a00000 00000000 00000020: 01e01180 00002581 00000000 00000000 00000030: 00400c0b 00000000 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000000 00000000 00027000 00000000 00000070: 412a0000 00040000 Model: Freescale Layerscape 2080a RDB Board Board: LS2088AE Rev1.0-RDB, Board Arch: V1, Board version: D, boot from vBank: 4 FPGA: v1.18 SERDES1 Reference : Clock1 = 156.25MHz Clock2 = 156.25MHz SERDES2 Reference : Clock1 = 100MHz Clock2 = 100MHz I2C: ready DRAM: 15.9 GiB DDR 15.9 GiB (DDR4, 64-bit, CL=13, ECC on) DDR Controller Interleaving Mode: 256B DDR Chip-Select Interleaving Mode: CS0+CS1 SEC0: RNG instantiated SEC0: RNG instantiated Using SERDES1 Protocol: 42 (0x2a) Using SERDES2 Protocol: 65 (0x41) Flash: 128 MiB NAND: 2048 MiB MMC: FSL_SDHC: 0 Loading Environment from Flash... OK EEPROM: Invalid ID (ff ff ff ff) In: serial Out: serial Err: serial VID: Core voltage after adjustment is at 1054 mV Net: DPMAC5@xgmii running firmware version 2.3.5 DPMAC5@xgmii: system interface XFI DPMAC5@xgmii: Aquantia AQR405 Firmware Version 2.3.5 DPMAC6@xgmii running firmware version 2.3.5 DPMAC6@xgmii: system interface XFI DPMAC6@xgmii: Aquantia AQR405 Firmware Version 2.3.5 DPMAC7@xgmii running firmware version 2.3.5 DPMAC7@xgmii: system interface XFI DPMAC7@xgmii: Aquantia AQR405 Firmware Version 2.3.5 DPMAC8@xgmii running firmware version 2.3.5 DPMAC8@xgmii: system interface XFI DPMAC8@xgmii: Aquantia AQR405 Firmware Version 2.3.5 PCIe0: pcie@3400000 disabled PCIe1: pcie@3500000 disabled PCIe2: pcie@3600000 Root Complex: x1 gen1 PCIe3: pcie@3700000 Root Complex: no link e1000: 68:05:ca:36:8d:e8 DPMAC1@xgmii Warning: DPMAC1@xgmii (eth0) using random MAC address - 26:fe:94:50:e5:84 , DPMAC2@xgmii Warning: DPMAC2@xgmii (eth1) using random MAC address - 7e:03:c1:4c:5e:15 , DPMAC3@xgmii Warning: DPMAC3@xgmii (eth2) using random MAC address - 76:0b:e8:36:d2:19 , DPMAC4@xgmii Warning: DPMAC4@xgmii (eth3) using random MAC address - 4e:50:15:96:3b:11 , DPMAC5@xgmii Warning: DPMAC5@xgmii (eth4) using random MAC address - 46:58:3c:ec:b7:1d , DPMAC6@xgmii Warning: DPMAC6@xgmii (eth5) using random MAC address - 62:42:e4:26:80:d1 , DPMAC7@xgmii Warning: DPMAC7@xgmii (eth6) using random MAC address - 6a:4a:cd:5c:0c:dd , DPMAC8@xgmii Warning: DPMAC8@xgmii (eth7) using random MAC address - 52:11:30:fc:e5:d5 , e1000#0 [PRIME] crc32+ fsl-mc: Booting Management Complex ... SUCCESS fsl-mc: Management Complex booted (version: 10.16.2, boot status: 0x1) Hit any key to stop autoboot: 10  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => setenv ipaddr 172.16.1.11; setenv serverip 172.16.1.4; setenv ethact e1000#0; setenv ethprime e1000#0 setenv ipaddr 172.16.1.11; setenv serverip 172.16.1.4; setenv ethact e1000#0; setenv ethprime e1000#0 => setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 => tftp 0x80080000 1248106/tftp-deploy-fjjq90d0/kernel/uImage tftp 0x80080000 1248106/tftp-deploy-fjjq90d0/kernel/uImage Using e1000#0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.11 Filename '1248106/tftp-deploy-fjjq90d0/kernel/uImage'. Load address: 0x80080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################ 1.1 MiB/s done Bytes transferred = 19307072 (1269a40 hex) => tftp 0x91000000 1248106/tftp-deploy-fjjq90d0/ramdisk/ramdisk.cpio.gz.uboot tftp 0x91000000 1248106/tftp-deploy-fjjq90d0/ramdisk/ramdisk.cpio.gz.uboot Using e1000#0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.11 Filename '1248106/tftp-deploy-fjjq90d0/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x91000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################ 2.3 MiB/s done Bytes transferred = 15189217 (e7c4e1 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 1248106/tftp-deploy-fjjq90d0/dtb/fsl-ls2088a-rdb.dtb tftp 0x90000000 1248106/tftp-deploy-fjjq90d0/dtb/fsl-ls2088a-rdb.dtb Using e1000#0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.11 Filename '1248106/tftp-deploy-fjjq90d0/dtb/fsl-ls2088a-rdb.dtb'. Load address: 0x90000000 Loading: *## 2.9 KiB/s done Bytes transferred = 16643 (4103 hex) => setenv bootargs 'console=ttyS1,115200n8 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0600 nousb default_hugepagesz=2m hugepagesz=2m hugepages=256 arm-smmu-mod.disable_bypass=n arm-smmu.disable_bypass=n ip=dhcp' setenv bootargs 'console=ttyS1,115200n8 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0600 nousb default_hugepagesz=2m hugepagesz=2m hugepages=256 arm-smmu-mod.disable_bypass=n arm-smmu.disable_bypass=n ip=dhcp' => bootm 0x80080000 0x91000000 0x90000000 bootm 0x80080000 0x91000000 0x90000000 ## Booting kernel from Legacy Image at 80080000 ... Image Name: Created: 2023-08-30 18:25:25 UTC Image Type: AArch64 Linux Kernel Image (uncompressed) Data Size: 19307008 Bytes = 18.4 MiB Load Address: 80080000 Entry Point: 80080000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 91000000 ... Image Name: Created: 2023-08-30 18:25:28 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 15189153 Bytes = 14.5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Loading Kernel Image ... OK Using Device Tree in place at 0000000090000000, end 0000000090007102 fsl-mc: DPL not deployed, DPAA2 ethernet not work Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd082] [ 0.000000] Linux version 4.19.293-cip102 (KernelCI@build-j28665-arm64-gcc-10-defconfig-wthtf) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP PREEMPT Wed Aug 30 18:12:50 UTC 2023 [ 0.000000] Machine model: Freescale Layerscape 2088A RDB Board [ 0.000000] earlycon: uart8250 at MMIO 0x00000000021c0600 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 32 MiB at 0x00000000f9c00000 [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x000000837fffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x837ffdda40-0x837ffdf1ff] [ 0.000000] Zone ranges: [ 0.000000] DMA32 [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] Normal [mem 0x0000000100000000-0x000000837fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fbdfffff] [ 0.000000] node 0: [mem 0x0000008080000000-0x000000837fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000837fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 22 pages/cpu s52760 r8192 d29160 u90112 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: enabling workaround for Branch predictor hardening [ 0.000000] CPU features: enabling workaround for EL2 vector hardening [ 0.000000] Speculative Store Bypass Disable mitigation not required [ 0.000000] CPU features: enabling workaround for Spectre-BHB [ 0.000000] CPU features: enabling workaround for ARM erratum 1742098 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 3595776 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttyS1,115200n8 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0600 nousb default_hugepagesz=2m hugepagesz=2m hugepages=256 arm-smmu-mod.disable_bypass=n arm-smmu.disable_bypass=n ip=dhcp [ 0.000000] software IO TLB: mapped [mem 0xf5c00000-0xf9c00000] (64MB) [ 0.000000] Memory: 14249232K/14612480K available (11196K kernel code, 1382K rwdata, 4968K rodata, 1280K init, 377K bss, 330480K reserved, 32768K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=8. [ 0.000000] Tasks RCU enabled. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: Distributor has no Range Selector support [ 0.000000] GICv3: no VLPI support, no direct LPI support [ 0.000000] ITS [mem 0x06020000-0x0603ffff] [ 0.000000] ITS@0x0000000006020000: allocated 8192 Devices @8371850000 (flat, esz 8, psz 64K, shr 0) [ 0.000000] ITS: using cache flushing for cmd queue [ 0.000000] GIC: using LPI property table @0x0000008371860000 [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006100000 [ 0.000000] CPU0: using LPI pending table @0x0000008371870000 [ 0.000000] GIC: using cache flushing for LPI property table [ 0.000000] arch_timer: Enabling global workaround for Freescale erratum a005858 [ 0.000000] arch_timer: CPU0: Trapping CNTVCT access [ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c409fb33, max_idle_ns: 440795203156 ns [ 0.000001] sched_clock: 56 bits at 25MHz, resolution 39ns, wraps every 4398046511103ns [ 0.008212] Console: colour dummy device 80x25 [ 0.012710] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) [ 0.023138] pid_max: default: 32768 minimum: 301 [ 0.027813] Security Framework initialized [ 0.035420] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes) [ 0.044611] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes) [ 0.051960] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes) [ 0.058944] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes) [ 0.066847] ASID allocator initialised with 32768 entries [ 0.072325] rcu: Hierarchical SRCU implementation. [ 0.077287] Platform MSI: gic-its@6020000 domain created [ 0.082668] PCI/MSI: /interrupt-controller@6000000/gic-its@6020000 domain created [ 0.090491] EFI services will not be available. [ 0.095208] smp: Bringing up secondary CPUs ... [ 0.099973] Detected PIPT I-cache on CPU1 [ 0.099987] GICv3: CPU1: found redistributor 1 region 0:0x0000000006120000 [ 0.100019] CPU1: using LPI pending table @0x000000836fdf0000 [ 0.100035] arch_timer: CPU1: Trapping CNTVCT access [ 0.100038] CPU1: Booted secondary processor 0x0000000001 [0x410fd082] [ 0.100278] Detected PIPT I-cache on CPU2 [ 0.100293] GICv3: CPU2: found redistributor 100 region 0:0x0000000006140000 [ 0.100325] CPU2: using LPI pending table @0x000000836fe50000 [ 0.100341] arch_timer: CPU2: Trapping CNTVCT access [ 0.100345] CPU2: Booted secondary processor 0x0000000100 [0x410fd082] [ 0.100581] Detected PIPT I-cache on CPU3 [ 0.100591] GICv3: CPU3: found redistributor 101 region 0:0x0000000006160000 [ 0.100620] CPU3: using LPI pending table @0x000000836fe60000 [ 0.100632] arch_timer: CPU3: Trapping CNTVCT access [ 0.100635] CPU3: Booted secondary processor 0x0000000101 [0x410fd082] [ 0.100866] Detected PIPT I-cache on CPU4 [ 0.100880] GICv3: CPU4: found redistributor 200 region 0:0x0000000006180000 [ 0.100911] CPU4: using LPI pending table @0x000000836fe80000 [ 0.100927] arch_timer: CPU4: Trapping CNTVCT access [ 0.100931] CPU4: Booted secondary processor 0x0000000200 [0x410fd082] [ 0.101167] Detected PIPT I-cache on CPU5 [ 0.101177] GICv3: CPU5: found redistributor 201 region 0:0x00000000061a0000 [ 0.101206] CPU5: using LPI pending table @0x000000836fed0000 [ 0.101218] arch_timer: CPU5: Trapping CNTVCT access [ 0.101221] CPU5: Booted secondary processor 0x0000000201 [0x410fd082] [ 0.101449] Detected PIPT I-cache on CPU6 [ 0.101464] GICv3: CPU6: found redistributor 300 region 0:0x00000000061c0000 [ 0.101496] CPU6: using LPI pending table @0x000000836fef0000 [ 0.101512] arch_timer: CPU6: Trapping CNTVCT access [ 0.101516] CPU6: Booted secondary processor 0x0000000300 [0x410fd082] [ 0.101749] Detected PIPT I-cache on CPU7 [ 0.101760] GICv3: CPU7: found redistributor 301 region 0:0x00000000061e0000 [ 0.101790] CPU7: using LPI pending table @0x000000836ff00000 [ 0.101801] arch_timer: CPU7: Trapping CNTVCT access [ 0.101805] CPU7: Booted secondary processor 0x0000000301 [0x410fd082] [ 0.101841] smp: Brought up 1 node, 8 CPUs [ 0.305201] SMP: Total of 8 processors activated. [ 0.309945] CPU features: detected: GIC system register CPU interface [ 0.316434] CPU features: detected: 32-bit EL0 Support [ 0.322131] CPU: All CPU(s) started at EL2 [ 0.326278] alternatives: patching kernel code [ 0.331302] devtmpfs: initialized [ 0.335787] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.345627] futex hash table entries: 2048 (order: 5, 131072 bytes) [ 0.352256] pinctrl core: initialized pinctrl subsystem [ 0.358000] DMI not present or invalid. [ 0.362103] NET: Registered protocol family 16 [ 0.366727] audit: initializing netlink subsys (disabled) [ 0.372229] audit: type=2000 audit(0.252:1): state=initialized audit_enabled=0 res=1 [ 0.380028] cpuidle: using governor menu [ 0.384076] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.391378] DMA: preallocated 256 KiB pool for atomic allocations [ 0.397840] Serial: AMBA PL011 UART driver [ 0.402623] Machine: Freescale Layerscape 2088A RDB Board [ 0.408065] SoC family: QorIQ LS2088A [ 0.411749] SoC ID: svr:0x87090010, Revision: 1.0 [ 0.426388] HugeTLB registered 2.00 MiB page size, pre-allocated 256 pages [ 0.433540] cryptd: max_cpu_qlen set to 1000 [ 0.438149] ACPI: Interpreter disabled. [ 0.442366] vgaarb: loaded [ 0.445185] SCSI subsystem initialized [ 0.449155] usbcore: registered new interface driver usbfs [ 0.454698] usbcore: registered new interface driver hub [ 0.460064] usbcore: registered new device driver usb [ 0.465357] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported [ 0.472713] i2c i2c-0: IMX I2C adapter registered [ 0.477456] i2c i2c-0: can't use DMA, using PIO instead. [ 0.482968] pps_core: LinuxPPS API ver. 1 registered [ 0.487968] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.497193] PTP clock support registered [ 0.501194] EDAC MC: Ver: 3.0.0 [ 0.504800] Advanced Linux Sound Architecture Driver Initialized. [ 0.511218] clocksource: Switched to clocksource arch_sys_counter [ 0.517409] VFS: Disk quotas dquot_6.6.0 [ 0.521372] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.528351] pnp: PnP ACPI: disabled [ 0.534415] NET: Registered protocol family 2 [ 0.539415] IP idents hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.549396] tcp_listen_portaddr_hash hash table entries: 8192 (order: 5, 131072 bytes) [ 0.557548] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.565503] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 0.572711] TCP: Hash tables configured (established 131072 bind 65536) [ 0.579464] UDP hash table entries: 8192 (order: 6, 262144 bytes) [ 0.585789] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes) [ 0.592577] NET: Registered protocol family 1 [ 0.597184] RPC: Registered named UNIX socket transport module. [ 0.603143] RPC: Registered udp transport module. [ 0.607872] RPC: Registered tcp transport module. [ 0.612601] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.619148] Unpacking initramfs... [ 0.982983] Freeing initrd memory: 14828K [ 0.987459] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 0.995392] kvm [1]: 8-bit VMID [ 0.998771] kvm [1]: vgic-v2@c0e0000 [ 1.002378] kvm [1]: GIC system register CPU interface enabled [ 1.008356] kvm [1]: vgic interrupt IRQ1 [ 1.012390] kvm [1]: Hyp mode initialized successfully [ 1.019175] Initialise system trusted keyrings [ 1.023716] workingset: timestamp_bits=44 max_order=22 bucket_order=0 [ 1.032642] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.038777] NFS: Registering the id_resolver key type [ 1.043869] Key type id_resolver registered [ 1.048078] Key type id_legacy registered [ 1.052113] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.058853] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 1.066361] 9p: Installing v9fs 9p2000 file system support [ 1.073314] Key type asymmetric registered [ 1.077434] Asymmetric key parser 'x509' registered [ 1.082355] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244) [ 1.089798] io scheduler noop registered [ 1.093742] io scheduler deadline registered [ 1.098075] io scheduler cfq registered (default) [ 1.102807] io scheduler mq-deadline registered [ 1.107361] io scheduler kyber registered [ 1.113866] layerscape-pcie 3600000.pcie: host bridge /soc/pcie@3600000 ranges: [ 1.121242] layerscape-pcie 3600000.pcie: IO 0x3000010000..0x300001ffff -> 0x00000000 [ 1.129392] layerscape-pcie 3600000.pcie: MEM 0x3040000000..0x307fffffff -> 0x40000000 [ 1.137618] layerscape-pcie 3600000.pcie: PCI host bridge to bus 0000:00 [ 1.144367] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.149882] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 1.156104] pci_bus 0000:00: root bus resource [mem 0x3040000000-0x307fffffff] (bus address [0x40000000-0x7fffffff]) [ 1.168648] pci 0000:00:00.0: BAR 1: assigned [mem 0x3040000000-0x3043ffffff] [ 1.175830] pci 0000:00:00.0: BAR 0: assigned [mem 0x3044000000-0x3044ffffff] [ 1.183016] pci 0000:00:00.0: BAR 6: assigned [mem 0x3045000000-0x3045ffffff pref] [ 1.190631] pci 0000:00:00.0: BAR 14: assigned [mem 0x3046000000-0x30460fffff] [ 1.197901] pci 0000:00:00.0: BAR 13: assigned [io 0x1000-0x1fff] [ 1.204119] pci 0000:01:00.0: BAR 1: assigned [mem 0x3046000000-0x304607ffff] [ 1.211316] pci 0000:01:00.0: BAR 6: assigned [mem 0x3046080000-0x30460bffff pref] [ 1.218936] pci 0000:01:00.0: BAR 0: assigned [mem 0x30460c0000-0x30460dffff] [ 1.226134] pci 0000:01:00.0: BAR 3: assigned [mem 0x30460e0000-0x30460e3fff] [ 1.233327] pci 0000:01:00.0: BAR 2: assigned [io 0x1000-0x101f] [ 1.239476] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 1.244734] pci 0000:00:00.0: bridge window [io 0x1000-0x1fff] [ 1.250862] pci 0000:00:00.0: bridge window [mem 0x3046000000-0x30460fffff] [ 1.258105] layerscape-pcie 3700000.pcie: host bridge /soc/pcie@3700000 ranges: [ 1.265468] layerscape-pcie 3700000.pcie: IO 0x3800010000..0x380001ffff -> 0x00000000 [ 1.273616] layerscape-pcie 3700000.pcie: MEM 0x3840000000..0x387fffffff -> 0x40000000 [ 1.281817] layerscape-pcie 3700000.pcie: PCI host bridge to bus 0001:00 [ 1.288564] pci_bus 0001:00: root bus resource [bus 00-ff] [ 1.294083] pci_bus 0001:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) [ 1.303106] pci_bus 0001:00: root bus resource [mem 0x3840000000-0x387fffffff] (bus address [0x40000000-0x7fffffff]) [ 1.314416] pci 0001:00:00.0: BAR 6: assigned [mem 0x3840000000-0x38400007ff pref] [ 1.322041] pci 0001:00:00.0: PCI bridge to [bus 01-ff] [ 1.327698] EINJ: ACPI disabled. [ 1.334034] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.341175] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 8, base_baud = 21875000) is a 16550A [ 1.350141] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 8, base_baud = 21875000) is a 16550A [ 1.358914] console [ttyS1] enabled [ 1.358914] console [ttyS1] enabled [ 1.365903] bootconsole [uart8250] disabled [ 1.365903] bootconsole [uart8250] disabled [ 1.374487] SuperH (H)SCI(F) driver initialized [ 1.379141] msm_serial: driver initialized [ 1.383409] arm-smmu: deprecated \"mmu-masters\" DT property in use; DMA API support unavailable [ 1.392312] arm-smmu 5000000.iommu: probing hardware configuration... [ 1.398752] arm-smmu 5000000.iommu: SMMUv2 with: [ 1.403369] arm-smmu 5000000.iommu: stage 1 translation [ 1.408677] arm-smmu 5000000.iommu: stage 2 translation [ 1.413987] arm-smmu 5000000.iommu: nested translation [ 1.419210] arm-smmu 5000000.iommu: non-coherent table walk [ 1.424869] arm-smmu 5000000.iommu: (IDR0.CTTW overridden by FW configuration) [ 1.432175] arm-smmu 5000000.iommu: stream matching with 128 register groups [ 1.439311] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) [ 1.445837] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 [ 1.452277] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA [ 1.458716] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA [ 1.468379] loop: module loaded [ 1.472226] ahci-qoriq 3200000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 1.481192] ahci-qoriq 3200000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst [ 1.491198] scsi host0: ahci-qoriq [ 1.494739] ata1: SATA max UDMA/133 mmio [mem 0x03200000-0x0320ffff] port 0x100 irq 94 [ 1.502729] ahci-qoriq 3210000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 1.511692] ahci-qoriq 3210000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst [ 1.521582] scsi host1: ahci-qoriq [ 1.525078] ata2: SATA max UDMA/133 mmio [mem 0x03210000-0x0321ffff] port 0x100 irq 95 [ 1.534054] tun: Universal TUN/TAP device driver, 1.6 [ 1.539395] thunder_xcv, ver 1.0 [ 1.542630] thunder_bgx, ver 1.0 [ 1.545873] nicpf, ver 1.0 [ 1.548725] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 1.554554] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 1.560860] e1000e 0000:01:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 1.627650] e1000e 0000:01:00.0 0000:01:00.0 (uninitialized): registered PHC clock [ 1.697171] e1000e 0000:01:00.0 eth0: (PCI Express:2.5GT/s:Width x1) 68:05:ca:36:8d:e8 [ 1.705094] e1000e 0000:01:00.0 eth0: Intel(R) PRO/1000 Network Connection [ 1.711981] e1000e 0000:01:00.0 eth0: MAC: 3, PHY: 8, PBA No: E46981-008 [ 1.718710] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 1.725670] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.731256] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 1.739084] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 1.745139] sky2: driver version 1.30 [ 1.749030] VFIO - User Level meta-driver version: 0.3 [ 1.754352] dwc3 3100000.usb3: Failed to get clk 'ref': -2 [ 1.760108] dwc3 3110000.usb3: Failed to get clk 'ref': -2 [ 1.766129] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.772659] ehci-pci: EHCI PCI platform driver [ 1.777113] ehci-platform: EHCI generic platform driver [ 1.782374] ehci-orion: EHCI orion driver [ 1.786410] ehci-exynos: EHCI EXYNOS driver [ 1.790621] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.796803] ohci-pci: OHCI PCI platform driver [ 1.801260] ohci-platform: OHCI generic platform driver [ 1.806516] ohci-exynos: OHCI EXYNOS driver [ 1.810825] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 1.816314] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 1.817372] ata1: SATA link down (SStatus 0 SControl 300) [ 1.824142] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 [ 1.838777] xhci-hcd xhci-hcd.0.auto: irq 96, io mem 0x03100000 [ 1.844971] hub 1-0:1.0: USB hub found [ 1.845373] ata2: SATA link down (SStatus 0 SControl 300) [ 1.848729] hub 1-0:1.0: 1 port detected [ 1.858139] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 1.863630] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 1.871290] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed [ 1.877832] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.886085] hub 2-0:1.0: USB hub found [ 1.889840] hub 2-0:1.0: 1 port detected [ 1.893903] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 1.899391] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 [ 1.907260] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 [ 1.916669] xhci-hcd xhci-hcd.1.auto: irq 97, io mem 0x03110000 [ 1.922811] hub 3-0:1.0: USB hub found [ 1.926569] hub 3-0:1.0: 1 port detected [ 1.930588] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 1.936077] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 [ 1.943733] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 1.950275] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.958535] hub 4-0:1.0: USB hub found [ 1.962291] hub 4-0:1.0: 1 port detected [ 1.966437] usbcore: registered new interface driver usb-storage [ 1.973370] i2c /dev entries driver [ 1.977835] i2c i2c-0: Added multiplexed i2c bus 1 [ 2.083248] rtc-ds3232: probe of 2-0068 failed with error -110 [ 2.089096] i2c i2c-0: Added multiplexed i2c bus 2 [ 2.093994] i2c i2c-0: Added multiplexed i2c bus 3 [ 2.098892] i2c i2c-0: Added multiplexed i2c bus 4 [ 2.103753] i2c i2c-0: Added multiplexed i2c bus 5 [ 2.108610] i2c i2c-0: Added multiplexed i2c bus 6 [ 2.113471] i2c i2c-0: Added multiplexed i2c bus 7 [ 2.118328] i2c i2c-0: Added multiplexed i2c bus 8 [ 2.123117] pca954x 0-0075: registered 8 multiplexed busses for I2C mux pca9547 [ 2.131309] sp805-wdt c000000.wdt: registration successful [ 2.136904] sp805-wdt c010000.wdt: registration successful [ 2.142451] sp805-wdt c100000.wdt: registration successful [ 2.147998] sp805-wdt c110000.wdt: registration successful [ 2.153543] sp805-wdt c200000.wdt: registration successful [ 2.159091] sp805-wdt c210000.wdt: registration successful [ 2.164639] sp805-wdt c300000.wdt: registration successful [ 2.170188] sp805-wdt c310000.wdt: registration successful [ 2.176286] sdhci: Secure Digital Host Controller Interface driver [ 2.182468] sdhci: Copyright(c) Pierre Ossman [ 2.186922] Synopsys Designware Multimedia Card Interface Driver [ 2.193207] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.223759] mmc0: SDHCI controller on 2140000.esdhc [2140000.esdhc] using ADMA 64-bit [ 2.232018] ledtrig-cpu: registered to indicate activity on CPUs [ 2.238413] usbcore: registered new interface driver usbhid [ 2.243984] usbhid: USB HID core driver [ 2.248421] optee: probing for conduit method from DT. [ 2.253558] optee: api uid mismatch [ 2.257466] NET: Registered protocol family 17 [ 2.261986] 9pnet: Installing 9P2000 support [ 2.266278] Key type dns_resolver registered [ 2.270805] registered taskstats version 1 [ 2.274900] Loading compiled-in X.509 certificates [ 2.280461] hctosys: unable to open rtc device (rtc0) [ 4.952218] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None [ 4.987228] Sending DHCP requests .., OK [ 8.463153] IP-Config: Got DHCP answer from 172.16.1.4, my address is 172.16.1.171 [ 8.470721] IP-Config: Complete: [ 8.473949] device=eth0, hwaddr=68:05:ca:36:8d:e8, ipaddr=172.16.1.171, mask=255.255.255.0, gw=172.16.1.4 [ 8.483951] host=172.16.1.171, domain=example.org, nis-domain=(none) [ 8.490738] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= [ 8.490739] nameserver0=172.16.1.4 [ 8.500842] ALSA device list: [ 8.503809] No soundcards found. [ 8.507669] Freeing unused kernel memory: 1280K [ 8.512254] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: [ 8.542434] udevd[1545]: starting version 3.2.9 [ 8.547249] random: udevd: uninitialized urandom read (16 bytes read) [ 8.553747] random: udevd: uninitialized urandom read (16 bytes read) [ 8.560219] random: udevd: uninitialized urandom read (16 bytes read) [ 8.568636] udevd[1545]: specified user 'tss' unknown [ 8.573720] udevd[1545]: specified group 'tss' unknown [ 8.579473] udevd[1546]: starting eudev-3.2.9 [ 8.632960] ina2xx 3-0040: error configuring the device: -11 [ 8.638797] lm90 4-004c: 4-004c supply vcc not found, using dummy regulator [ 8.639694] udevd[1552]: Error changing net interface name eth0 to enp1s0: Device or resource busy [ 8.645958] lm90 4-004c: Linked as a consumer to regulator.0 [ 8.654982] udevd[1552]: could not rename interface '2' from 'eth0' to 'enp1s0': Device or resource busy [ 8.660637] lm90 4-004c: Failed to initialize device [ 8.674901] lm90 4-004c: Dropping the link to regulator.0 [ 8.680324] lm90: probe of 4-004c failed with error -11 done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: [ 8.728569] NET: Registered protocol family 10 [ 8.733703] Segment Routing with IPv6 OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1248106/environment . /lava-1248106/environment / # /lava-1248106/bin/lava-test-runner /lava-1248106/0 /lava-1248106/bin/lava-test-runner /lava-1248106/0 + export 'TESTRUN_[ 9.245899] ID=0_dmesg' + cd /lava-1248106/0/tests/0_dmesg + cat uuid + UUID=1248106_1.5.2.4.1 + set +x + KERNELCI_LAVA[ 9.260100] =y /bin/sh /opt/kernelci/dmesg.sh [ 9.277197] [ 9.292817] + [ 9.301634] set +x # / # #export SHELL=/bin/sh / # export SHELL=/bin/sh. /lava-1248106/environment / # . /lava-1248106/environment/lava-1248106/bin/lava-test-runner /lava-1248106/1 / # /lava-1248106/bin/lava-test-runner /lava-1248106/1 + export 'TESTRUN_[ 9.733321] ID=1_bootrr' + cd /lava-1248106/1/tests/1_bootrr + cat uuid + UUID=1248106_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/li[ 9.749110] bexec/bootrr/helpers:/lava-1248106/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/lib[ 9.764943] exec/bootrr + sh helpers/bootrr-auto /lava-124[ 9.777408] 8106/1/../bin/lava-test-case /lava-1248106/1/..[ 9.787745] /bin/lava-test-case /lava-1248106/1/../bin/lava-test-case + set +x / #