[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.35 (6 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 11733159/tftp-deploy-tfuocvym/kernel/zImage tftp 0x10000000 11733159/tftp-deploy-tfuocvym/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '11733159/tftp-deploy-tfuocvym/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 6.8 MiB/s done Bytes transferred = 8733184 (854200 hex) => tftp 0x14000000 11733159/tftp-deploy-tfuocvym/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 11733159/tftp-deploy-tfuocvym/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '11733159/tftp-deploy-tfuocvym/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################### 11.8 MiB/s done Bytes transferred = 9417355 (8fb28b hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 11733159/tftp-deploy-tfuocvym/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 11733159/tftp-deploy-tfuocvym/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '11733159/tftp-deploy-tfuocvym/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 10 MiB/s done Bytes transferred = 41818 (a35a hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/11733159/extract-nfsrootfs-27ckezbv,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/11733159/extract-nfsrootfs-27ckezbv,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x854200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 9417291 Bytes = 9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d359 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.296-cip103 (KernelCI@build-j70030-arm-gcc-10-multi-v7-defconfig-p6jm8) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Wed Oct 11 01:14:33 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] percpu: Embedded 16 pages/cpu s36748 r8192 d20596 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/11733159/extract-nfsrootfs-27ckezbv,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 942964K/1048576K available (12288K kernel code, 1597K rwdata, 4684K rodata, 2048K init, 394K bss, 40076K reserved, 65536K cma-reserved, 196608K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1598 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 395 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008444] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.021421] Console: colour dummy device 80x30 <6>[ 0.023304] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.033719] CPU: Testing write buffer coherency: ok <6>[ 0.038852] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.044150] pid_max: default: 32768 minimum: 301 <6>[ 0.049151] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.055917] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.064084] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.069810] Setting up static identity map for 0x10300000 - 0x103000a0 <6>[ 0.077515] rcu: Hierarchical SRCU implementation. <6>[ 0.084062] EFI services will not be available. <6>[ 0.086311] smp: Bringing up secondary CPUs ... <6>[ 0.091583] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.091589] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.102917] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.102922] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.114114] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.114120] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.124568] smp: Brought up 1 node, 4 CPUs <6>[ 0.128824] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.135240] CPU: All CPU(s) started in SVC mode. <6>[ 0.141198] devtmpfs: initialized <6>[ 0.150738] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.156189] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.165943] futex hash table entries: 1024 (order: 4, 65536 bytes) <6>[ 0.175476] pinctrl core: initialized pinctrl subsystem <6>[ 0.179781] DMI not present or invalid. <6>[ 0.182994] NET: Registered protocol family 16 <6>[ 0.190421] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.197065] cpuidle: using governor menu <6>[ 0.199087] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.213918] vdd1p1: supplied by regulator-dummy <6>[ 0.216382] vdd3p0: supplied by regulator-dummy <6>[ 0.221114] vdd2p5: supplied by regulator-dummy <6>[ 0.225949] vddarm: supplied by regulator-dummy <6>[ 0.230865] vddpu: supplied by regulator-dummy <6>[ 0.235268] vddsoc: supplied by regulator-dummy <6>[ 0.253744] No ATAGs? <6>[ 0.253894] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.261853] hw-breakpoint: maximum watchpoint size is 4 bytes. <4>[ 0.271330] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory <6>[ 0.278210] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver <6>[ 0.290060] Serial: AMBA PL011 UART driver <6>[ 0.293857] console [pstore-1] enabled <6>[ 0.295732] pstore: Registered ramoops as persistent store backend <6>[ 0.302027] ramoops: attached 0x10000@0x30000000, ecc: 0/0 <6>[ 0.330459] mxs-dma 110000.dma-apbh: initialized <6>[ 0.339951] vgaarb: loaded <5>[ 0.340881] SCSI subsystem initialized <6>[ 0.344484] usbcore: registered new interface driver usbfs <6>[ 0.349895] usbcore: registered new interface driver hub <6>[ 0.355412] usbcore: registered new device driver usb <6>[ 0.361981] i2c i2c-0: IMX I2C adapter registered <6>[ 0.365649] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.371792] i2c i2c-1: IMX I2C adapter registered <6>[ 0.376193] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.382128] i2c i2c-2: IMX I2C adapter registered <6>[ 0.386721] i2c i2c-2: can't use DMA, using PIO instead. <6>[ 0.393809] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.397501] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.406909] PTP clock support registered <6>[ 0.411283] EDAC MC: Ver: 3.0.0 <6>[ 0.417277] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.480342] NET: Registered protocol family 2 <6>[ 0.482549] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.490092] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) <6>[ 0.497018] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.504408] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) <6>[ 0.511151] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.517839] UDP hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.523817] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.530582] NET: Registered protocol family 1 <6>[ 0.535562] RPC: Registered named UNIX socket transport module. <6>[ 0.541214] RPC: Registered udp transport module. <6>[ 0.546142] RPC: Registered tcp transport module. <6>[ 0.551120] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.558260] Trying to unpack rootfs image as initramfs... <6>[ 1.280851] Freeing initrd memory: 9200K <4>[ 1.282729] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 1.289982] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 1.299922] Initialise system trusted keyrings <6>[ 1.302914] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 1.315479] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.319401] NFS: Registering the id_resolver key type <5>[ 1.324062] Key type id_resolver registered <5>[ 1.328494] Key type id_legacy registered <6>[ 1.332769] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 1.339571] Key type asymmetric registered <5>[ 1.341694] Asymmetric key parser 'x509' registered <6>[ 1.346865] bounce: pool size: 64 pages <6>[ 1.350974] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 1.358588] io scheduler noop registered <6>[ 1.362748] io scheduler deadline registered <6>[ 1.367422] io scheduler cfq registered (default) <6>[ 1.372230] io scheduler mq-deadline registered <6>[ 1.377015] io scheduler kyber registered <6>[ 1.403113] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 1.407655] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 1.414779] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 1.422089] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 1.442218] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set <6>[ 1.445608] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc <4>[ 1.453503] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set <6>[ 1.459652] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 <4>[ 1.467550] PU : no governor for states <4>[ 1.467637] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 1.471489] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc <6>[ 1.481263] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 1.546613] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 1.553948] SuperH (H)SCI(F) driver initialized <6>[ 1.556788] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX <6>[ 1.565554] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX <6>[ 1.576525] console [ttymxc1] enabled <6>[ 1.576525] console [ttymxc1] enabled <6>[ 1.581529] bootconsole [ec_imx21] disabled <6>[ 1.581529] bootconsole [ec_imx21] disabled <6>[ 1.591631] msm_serial: driver initialized <6>[ 1.597864] STMicroelectronics ASC driver initialized <6>[ 1.604987] STM32 USART driver initialized <4>[ 1.620234] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 1.628945] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 1.635907] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 1.642689] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 1.651726] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 1.658898] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 1.673536] brd: module loaded <6>[ 1.683559] loop: module loaded <6>[ 1.690186] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 1.698423] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 1.706697] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 1.715156] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <6>[ 1.725954] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 1.733238] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 1.742323] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 1.753118] scsi host0: ahci-imx <6>[ 1.757186] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 <6>[ 1.776061] CAN device driver interface <6>[ 1.781449] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 1.788529] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator <6>[ 1.797510] fec 2188000.ethernet: Linked as a consumer to regulator.0 <6>[ 1.806587] pps pps0: new PPS source ptp0 <6>[ 1.828206] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 1.835591] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 1.841719] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 1.847973] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 1.855202] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.866889] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 1.874614] usbcore: registered new interface driver pegasus <6>[ 1.880594] usbcore: registered new interface driver asix <6>[ 1.886299] usbcore: registered new interface driver ax88179_178a <6>[ 1.892710] usbcore: registered new interface driver cdc_ether <6>[ 1.898867] usbcore: registered new interface driver smsc75xx <6>[ 1.904920] usbcore: registered new interface driver smsc95xx <6>[ 1.910978] usbcore: registered new interface driver net1080 <6>[ 1.916933] usbcore: registered new interface driver cdc_subset <6>[ 1.923170] usbcore: registered new interface driver zaurus <6>[ 1.929092] usbcore: registered new interface driver cdc_ncm <6>[ 1.937951] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 1.944748] ehci-pci: EHCI PCI platform driver <6>[ 1.949517] ehci-platform: EHCI generic platform driver <6>[ 1.955289] ehci-orion: EHCI orion driver <6>[ 1.959814] SPEAr-ehci: EHCI SPEAr driver <6>[ 1.964277] ehci-st: EHCI STMicroelectronics driver <6>[ 1.969634] ehci-exynos: EHCI EXYNOS driver <6>[ 1.974261] ehci-atmel: EHCI Atmel driver <6>[ 1.978744] tegra-ehci: Tegra EHCI driver <6>[ 1.983239] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 1.989722] ohci-pci: OHCI PCI platform driver <6>[ 1.994474] ohci-platform: OHCI generic platform driver <6>[ 2.000241] SPEAr-ohci: OHCI SPEAr driver <6>[ 2.004702] ohci-st: OHCI STMicroelectronics driver <6>[ 2.010055] ohci-atmel: OHCI Atmel driver <6>[ 2.015337] usbcore: registered new interface driver usb-storage <6>[ 2.023905] imx_usb 2184000.usb: Linked as a consumer to regulator.9 <6>[ 2.036066] imx_usb 2184200.usb: Linked as a consumer to regulator.14 <6>[ 2.046236] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 2.051427] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 2.087327] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 2.088831] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 2.093659] hub 1-0:1.0: USB hub found <6>[ 2.098725] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 2.102731] hub 1-0:1.0: 1 port detected <6>[ 2.109242] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 2.119723] i2c /dev entries driver <6>[ 2.138953] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) <6>[ 2.150399] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.156848] sdhci: Copyright(c) Pierre Ossman <6>[ 2.163726] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.171993] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.178803] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO <6>[ 2.184237] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO <6>[ 2.189772] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.227482] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA <6>[ 2.235492] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO <6>[ 2.241036] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.280927] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA <6>[ 2.292399] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 2.299711] usbcore: registered new interface driver usbhid <6>[ 2.305590] usbhid: USB HID core driver <6>[ 2.315626] NET: Registered protocol family 10 <6>[ 2.315717] mmc0: new high speed SDHC card at address 0001 <6>[ 2.321451] Segment Routing with IPv6 <6>[ 2.327807] mmcblk0: mmc0:0001 SD 14.6 GiB <6>[ 2.330189] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.341355] NET: Registered protocol family 17 <6>[ 2.346080] can: controller area network core (rev 20170425 abi 9) <6>[ 2.352636] NET: Registered protocol family 29 <6>[ 2.357372] can: raw protocol (rev 20170425) <6>[ 2.361913] can: broadcast manager protocol (rev 20170425 t) <6>[ 2.367860] can: netlink gateway (rev 20170425) max_hops=1 <5>[ 2.374051] Key type dns_resolver registered <6>[ 2.379658] cpu cpu0: Linked as a consumer to regulator.4 <6>[ 2.385382] cpu cpu0: Linked as a consumer to regulator.5 <6>[ 2.391128] cpu cpu0: Linked as a consumer to regulator.6 <6>[ 2.397322] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 2.397629] ThumbEE CPU extension supported. <5>[ 2.408660] Registering SWP/SWPB emulation handler <5>[ 2.414472] Loading compiled-in X.509 certificates <6>[ 2.421157] pstore: Using compression: deflate <4>[ 2.430684] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 2.438434] GPT:29296874 != 30560255 <6>[ 2.441645] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <4>[ 2.442289] GPT:Alternate GPT header not at the end of the disk. <6>[ 2.449780] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <4>[ 2.455919] GPT:29296874 != 30560255 <4>[ 2.455926] GPT: Use GNU Parted to correct GPT errors. <6>[ 2.464459] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.466864] mmcblk0: p1 p2 p3 <6>[ 2.472289] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.491715] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.500404] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.507358] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.515189] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.524214] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.531337] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.539817] imx_thermal tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <6>[ 2.550256] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.557640] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.565893] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.573363] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.581876] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.590551] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.597499] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.605245] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.614261] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.621382] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.628589] hub 1-1:1.0: USB hub found <6>[ 2.629157] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.632735] hub 1-1:1.0: 3 ports detected <6>[ 2.639996] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.652460] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.659926] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.668452] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.677109] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.684070] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.691813] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.700833] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.707948] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.715578] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.722951] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.731796] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 2.738702] hctosys: unable to open rtc device (rtc0) <6>[ 2.745147] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.752695] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.761430] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.770118] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.777059] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.784930] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.793959] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.801086] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.808790] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.816145] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.877765] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 2.892713] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 5.997943] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 6.017311] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 6.047354] Sending DHCP requests ., OK <6>[ 6.091517] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.35 <6>[ 6.099854] IP-Config: Complete: <6>[ 6.103373] device=eth0, hwaddr=00:19:b8:08:f1:09, ipaddr=192.168.201.35, mask=255.255.255.0, gw=192.168.201.1 <6>[ 6.114123] host=imx6q-sabrelite-lava-cbg-5, domain=lava-rack, nis-domain=(none) <6>[ 6.122265] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 6.122275] nameserver0=192.168.201.1 <6>[ 6.140866] Freeing unused kernel memory: 2048K <6>[ 6.167632] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u2 <6>[ 6.975405] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 <6>[ 6.992567] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.004576] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.013669] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.022406] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.030183] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.037879] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) <6>[ 7.044259] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.063895] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.070776] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 7.077327] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.085623] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.094691] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.101878] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.110109] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.117578] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.126234] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.134405] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.144080] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.152891] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.160026] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 7.180234] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <4>[ 7.189821] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.195610] sgtl5000 0-000a: Linked as a consumer to regulator.7 <6>[ 7.205201] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.212341] sgtl5000 0-000a: Linked as a consumer to regulator.8 <6>[ 7.218725] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.226937] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 7.227055] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.239584] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.248582] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.256105] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.265531] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.274249] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 7.274296] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.289155] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 7.315421] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 7.321873] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 7.329122] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 0 <4>[ 7.337919] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.347128] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.358708] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.369482] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.378939] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.388216] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.395698] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.405222] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.414013] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.421166] panel-simple panel-lcd: Dropping the link to regulator.0 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. IP-Config: eth0 hardware address 00:19:b8:08:f1:09 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.35 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-5 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 8.371324] systemd[1]: System time before build time, advancing clock. <3>[ 8.401832] cgroup: cgroup2: unknown option "memory_recursiveprot" <30>[ 8.416841] systemd[1]: systemd 247.3-7+deb11u2 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 8.441203] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! <30>[ 8.479606] systemd[1]: Set hostname to . <30>[ 9.248750] systemd[1]: Queued start job for default target Graphical Interface. <5>[ 9.258269] random: systemd: uninitialized urandom read (16 bytes read) <28>[ 9.265364] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. <28>[ 9.278323] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) <30>[ 9.288016] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. <5>[ 9.327747] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 9.335888] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. <5>[ 9.387659] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 9.395669] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. <30>[ 9.438468] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. <30>[ 9.478421] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. <30>[ 9.517755] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. <30>[ 9.558027] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 9.570840] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. <30>[ 9.608344] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. <30>[ 9.637850] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. <30>[ 9.677831] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. <30>[ 9.707904] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. <30>[ 9.738716] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. <30>[ 9.818360] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. <30>[ 9.828548] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). <30>[ 9.869021] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. <30>[ 9.909820] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. <30>[ 9.950497] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. <30>[ 9.988928] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. <30>[ 10.028813] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 10.038360] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. <30>[ 10.050909] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... <30>[ 10.090851] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... <30>[ 10.153204] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... <30>[ 10.203968] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... <30>[ 10.241008] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... <5>[ 10.277890] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 10.287998] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... <30>[ 10.332759] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. <5>[ 10.343107] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 10.352775] systemd[1]: Starting Journal Service... Starting Journal Service... <5>[ 10.395052] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 10.404929] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... <30>[ 10.440880] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... <30>[ 10.480681] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... <30>[ 10.522662] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. <30>[ 10.558202] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. <30>[ 10.598701] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. <30>[ 10.655616] systemd[1]: modprobe@configfs.service: Succeeded. <30>[ 10.662563] systemd[1]: Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module configfs. <30>[ 10.698183] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Apply Kernel V<46>[ 10.985042] systemd-journald[164]: Received client request to flush runtime journal. ariables... Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. <5>[ 11.388115] random: systemd: uninitialized urandom read (16 bytes read) Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. <5>[ 11.481643] random: systemd-journal: uninitialized urandom read (16 bytes read) [ OK <5>[ 11.499472] random: systemd-journal: uninitialized urandom read (16 bytes read) ] Finished Coldplug All udev Devices. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... <5>[ 11.947423] random: crng init done <5>[ 11.951115] random: 48 urandom warning(s) missed due to ratelimiting [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Create Volatile Files and Directories. [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Found device /dev/ttymxc1. [ OK ] Started Network Name Resolution. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 4.19.296-cip103 #1 SMP Wed Oct 11 01:14:33 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/11733159/extract-nfsrootfs-27ckezbv' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/11733159/extract-nfsrootfs-27ckezbv' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/bash export SHELL=/bin/bash / # . /lava-11733159/environment . /lava-11733159/environment / # /lava-11733159/bin/lava-test-runner /lava-11733159/0 /lava-11733159/bin/lava-test-runner /lava-11733159/0 + export TESTRUN_ID=0_timesync-off + TESTRUN_ID=0_timesync-off + cd /lava-11733159/0/tests/0_timesync-off ++ cat uuid + UUID=11733159_1.6.2.4.1 + set +x + systemctl stop systemd-timesyncd + set +x + export TESTRUN_ID=1_kselftest-filesystems + TESTRUN_ID=1_kselftest-filesystems + cd /lava-11733159/0/tests/1_kselftest-filesystems ++ cat uuid + UUID=11733159_1.6.2.4.5 + set +x + cd ./automated/linux/kselftest/ + ./kselftest.sh -c filesystems -T '' -t kselftest_armhf.tar.gz -s True -u None -L '' -S /dev/null -b imx6q-sabrelite -g cip-gitlab -e '' -p /opt/kselftests/mainline/ -n 1 -i 1 INFO: install_deps skipped --2023-10-11 01:52:13-- http://none/ Resolving none (none)... failed: Name or service not known. wget: unable to resolve host address 'none' tar: None: Cannot open: No such file or directory tar: Error is not recoverable: exiting now ./kselftest.sh: 160: cd: can't cd to kselftest / #