[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.35 (7 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 11967632/tftp-deploy-x9ycie0j/kernel/zImage tftp 0x10000000 11967632/tftp-deploy-x9ycie0j/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '11967632/tftp-deploy-x9ycie0j/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 5.8 MiB/s done Bytes transferred = 8733184 (854200 hex) => tftp 0x14000000 11967632/tftp-deploy-x9ycie0j/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 11967632/tftp-deploy-x9ycie0j/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '11967632/tftp-deploy-x9ycie0j/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################ 14.4 MiB/s done Bytes transferred = 13337727 (cb847f hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 11967632/tftp-deploy-x9ycie0j/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 11967632/tftp-deploy-x9ycie0j/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '11967632/tftp-deploy-x9ycie0j/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 5.7 MiB/s done Bytes transferred = 41818 (a35a hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x854200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 13337663 Bytes = 12.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d359 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.298-cip104 (KernelCI@build-j9845-arm-gcc-10-multi-v7-defconfig-4gclp) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Wed Nov 8 12:07:58 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] percpu: Embedded 16 pages/cpu s36748 r8192 d20596 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 939136K/1048576K available (12288K kernel code, 1597K rwdata, 4684K rodata, 2048K init, 394K bss, 43904K reserved, 65536K cma-reserved, 196608K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1598 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 395 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000006] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008445] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.021336] Console: colour dummy device 80x30 <6>[ 0.023220] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.033635] CPU: Testing write buffer coherency: ok <6>[ 0.038767] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.044065] pid_max: default: 32768 minimum: 301 <6>[ 0.049074] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.055836] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.064000] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.069733] Setting up static identity map for 0x10300000 - 0x103000a0 <6>[ 0.077441] rcu: Hierarchical SRCU implementation. <6>[ 0.084008] EFI services will not be available. <6>[ 0.086264] smp: Bringing up secondary CPUs ... <6>[ 0.091527] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.091534] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.102881] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.102888] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.114064] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.114071] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.124513] smp: Brought up 1 node, 4 CPUs <6>[ 0.128768] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.135185] CPU: All CPU(s) started in SVC mode. <6>[ 0.141159] devtmpfs: initialized <6>[ 0.150793] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.156244] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.165997] futex hash table entries: 1024 (order: 4, 65536 bytes) <6>[ 0.175529] pinctrl core: initialized pinctrl subsystem <6>[ 0.179815] DMI not present or invalid. <6>[ 0.183055] NET: Registered protocol family 16 <6>[ 0.190385] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.197006] cpuidle: using governor menu <6>[ 0.199026] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.214050] vdd1p1: supplied by regulator-dummy <6>[ 0.216520] vdd3p0: supplied by regulator-dummy <6>[ 0.221243] vdd2p5: supplied by regulator-dummy <6>[ 0.226079] vddarm: supplied by regulator-dummy <6>[ 0.230993] vddpu: supplied by regulator-dummy <6>[ 0.235396] vddsoc: supplied by regulator-dummy <6>[ 0.254071] No ATAGs? <6>[ 0.254217] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.262177] hw-breakpoint: maximum watchpoint size is 4 bytes. <4>[ 0.271699] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory <6>[ 0.278580] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver <6>[ 0.290509] Serial: AMBA PL011 UART driver <6>[ 0.294364] console [pstore-1] enabled <6>[ 0.296200] pstore: Registered ramoops as persistent store backend <6>[ 0.302454] ramoops: attached 0x10000@0x30000000, ecc: 0/0 <6>[ 0.330876] mxs-dma 110000.dma-apbh: initialized <6>[ 0.340297] vgaarb: loaded <5>[ 0.341216] SCSI subsystem initialized <6>[ 0.344816] usbcore: registered new interface driver usbfs <6>[ 0.350281] usbcore: registered new interface driver hub <6>[ 0.355778] usbcore: registered new device driver usb <6>[ 0.362268] i2c i2c-0: IMX I2C adapter registered <6>[ 0.366017] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.372120] i2c i2c-1: IMX I2C adapter registered <6>[ 0.376540] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.382475] i2c i2c-2: IMX I2C adapter registered <6>[ 0.387069] i2c i2c-2: can't use DMA, using PIO instead. <6>[ 0.394154] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.397847] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.407257] PTP clock support registered <6>[ 0.411636] EDAC MC: Ver: 3.0.0 <6>[ 0.417596] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.482403] NET: Registered protocol family 2 <6>[ 0.484613] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.492155] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) <6>[ 0.499114] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.506433] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) <6>[ 0.513215] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.519899] UDP hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.525879] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.532649] NET: Registered protocol family 1 <6>[ 0.537650] RPC: Registered named UNIX socket transport module. <6>[ 0.543245] RPC: Registered udp transport module. <6>[ 0.548227] RPC: Registered tcp transport module. <6>[ 0.553162] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.560326] Trying to unpack rootfs image as initramfs... <6>[ 1.679190] Freeing initrd memory: 13028K <4>[ 1.681082] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 1.688419] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 1.698334] Initialise system trusted keyrings <6>[ 1.701341] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 1.713669] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.717545] NFS: Registering the id_resolver key type <5>[ 1.722273] Key type id_resolver registered <5>[ 1.726657] Key type id_legacy registered <6>[ 1.730985] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 1.737801] Key type asymmetric registered <5>[ 1.739886] Asymmetric key parser 'x509' registered <6>[ 1.745064] bounce: pool size: 64 pages <6>[ 1.749197] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 1.756763] io scheduler noop registered <6>[ 1.760952] io scheduler deadline registered <6>[ 1.765593] io scheduler cfq registered (default) <6>[ 1.770437] io scheduler mq-deadline registered <6>[ 1.775204] io scheduler kyber registered <6>[ 1.801382] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 1.805906] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 1.813048] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 1.820346] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 1.840578] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set <6>[ 1.843971] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc <4>[ 1.851821] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set <6>[ 1.858029] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 <4>[ 1.865922] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <4>[ 1.867617] PU : no governor for states <6>[ 1.875531] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 1.879610] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc <6>[ 1.937450] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 1.944741] SuperH (H)SCI(F) driver initialized <6>[ 1.947615] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX <6>[ 1.956315] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX <6>[ 1.967316] console [ttymxc1] enabled <6>[ 1.967316] console [ttymxc1] enabled <6>[ 1.972320] bootconsole [ec_imx21] disabled <6>[ 1.972320] bootconsole [ec_imx21] disabled <6>[ 1.982414] msm_serial: driver initialized <6>[ 1.988655] STMicroelectronics ASC driver initialized <6>[ 1.995784] STM32 USART driver initialized <4>[ 2.010833] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.019532] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.026493] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.033279] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.042311] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.049475] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.064093] brd: module loaded <6>[ 2.074106] loop: module loaded <6>[ 2.080714] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 2.088939] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 2.097215] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 2.105675] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <6>[ 2.116454] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 2.123741] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 2.132830] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 2.143615] scsi host0: ahci-imx <6>[ 2.147735] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 <6>[ 2.166667] CAN device driver interface <6>[ 2.172029] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 2.179131] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator <6>[ 2.188132] fec 2188000.ethernet: Linked as a consumer to regulator.0 <6>[ 2.197196] pps pps0: new PPS source ptp0 <6>[ 2.227752] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 2.235127] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 2.241246] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.247483] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 2.254724] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 2.266309] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 2.274032] usbcore: registered new interface driver pegasus <6>[ 2.280021] usbcore: registered new interface driver asix <6>[ 2.285718] usbcore: registered new interface driver ax88179_178a <6>[ 2.292128] usbcore: registered new interface driver cdc_ether <6>[ 2.298295] usbcore: registered new interface driver smsc75xx <6>[ 2.304351] usbcore: registered new interface driver smsc95xx <6>[ 2.310412] usbcore: registered new interface driver net1080 <6>[ 2.316379] usbcore: registered new interface driver cdc_subset <6>[ 2.322610] usbcore: registered new interface driver zaurus <6>[ 2.328533] usbcore: registered new interface driver cdc_ncm <6>[ 2.337299] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 2.344125] ehci-pci: EHCI PCI platform driver <6>[ 2.348900] ehci-platform: EHCI generic platform driver <6>[ 2.354676] ehci-orion: EHCI orion driver <6>[ 2.359195] SPEAr-ehci: EHCI SPEAr driver <6>[ 2.363653] ehci-st: EHCI STMicroelectronics driver <6>[ 2.368999] ehci-exynos: EHCI EXYNOS driver <6>[ 2.373628] ehci-atmel: EHCI Atmel driver <6>[ 2.378113] tegra-ehci: Tegra EHCI driver <6>[ 2.382601] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 2.389083] ohci-pci: OHCI PCI platform driver <6>[ 2.393834] ohci-platform: OHCI generic platform driver <6>[ 2.399611] SPEAr-ohci: OHCI SPEAr driver <6>[ 2.404076] ohci-st: OHCI STMicroelectronics driver <6>[ 2.409425] ohci-atmel: OHCI Atmel driver <6>[ 2.414645] usbcore: registered new interface driver usb-storage <6>[ 2.423183] imx_usb 2184000.usb: Linked as a consumer to regulator.9 <6>[ 2.435193] imx_usb 2184200.usb: Linked as a consumer to regulator.14 <6>[ 2.445351] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 2.450545] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 2.487623] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 2.489126] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 2.493964] hub 1-0:1.0: USB hub found <6>[ 2.499011] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 2.503031] hub 1-0:1.0: 1 port detected <6>[ 2.509538] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 2.519897] i2c /dev entries driver <6>[ 2.539139] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) <6>[ 2.550467] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.556915] sdhci: Copyright(c) Pierre Ossman <6>[ 2.563801] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.572005] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.578811] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO <6>[ 2.584244] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO <6>[ 2.589776] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.627816] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA <6>[ 2.635825] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO <6>[ 2.641363] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.681288] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA <6>[ 2.692764] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 2.700038] usbcore: registered new interface driver usbhid <6>[ 2.705911] usbhid: USB HID core driver <6>[ 2.715868] NET: Registered protocol family 10 <6>[ 2.721732] Segment Routing with IPv6 <6>[ 2.725769] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.732544] NET: Registered protocol family 17 <6>[ 2.737264] can: controller area network core (rev 20170425 abi 9) <6>[ 2.743809] NET: Registered protocol family 29 <6>[ 2.748542] can: raw protocol (rev 20170425) <6>[ 2.753081] can: broadcast manager protocol (rev 20170425 t) <6>[ 2.759032] can: netlink gateway (rev 20170425) max_hops=1 <5>[ 2.765148] Key type dns_resolver registered <6>[ 2.770707] cpu cpu0: Linked as a consumer to regulator.4 <6>[ 2.776427] cpu cpu0: Linked as a consumer to regulator.5 <6>[ 2.782184] cpu cpu0: Linked as a consumer to regulator.6 <6>[ 2.788669] ThumbEE CPU extension supported. <5>[ 2.793216] Registering SWP/SWPB emulation handler <5>[ 2.799604] Loading compiled-in X.509 certificates <6>[ 2.806123] pstore: Using compression: deflate <6>[ 2.827854] mmc0: new high speed SDHC card at address 0001 <6>[ 2.834718] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.842133] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.850617] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.859451] mmcblk0: mmc0:0001 SD 14.6 GiB <6>[ 2.864199] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.873094] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.881798] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.888974] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 2.895855] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.903879] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.912948] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.920324] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.929102] imx_thermal tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <6>[ 2.939657] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.947218] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.955530] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.963257] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.971835] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.980542] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.987666] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.995478] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.004512] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.011842] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.019787] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.027306] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.035526] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <4>[ 3.043138] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 3.050819] GPT:29296874 != 30560255 <4>[ 3.054658] GPT:Alternate GPT header not at the end of the disk. <4>[ 3.060955] GPT:29296874 != 30560255 <4>[ 3.064794] GPT: Use GNU Parted to correct GPT errors. <6>[ 3.070242] mmcblk0: p1 p2 p3 <6>[ 3.073712] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.082284] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.090963] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.098097] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.105925] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.114960] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.122789] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.130563] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.137949] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.146108] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.153614] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.162136] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.170842] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.177871] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.185648] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.194700] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.201863] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.210454] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 3.217297] hub 1-1:1.0: USB hub found <6>[ 3.221476] hctosys: unable to open rtc device (rtc0) <6>[ 3.222020] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.234264] hub 1-1:1.0: 3 ports detected <6>[ 3.238633] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.247065] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.254655] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.263276] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.271984] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.278968] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.286778] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.295828] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.303134] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.311261] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.318652] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.326833] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.334316] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 3.342022] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <4>[ 3.342875] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.356856] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 3.365407] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.378425] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.386254] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.395278] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.402398] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 6.478279] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 6.497699] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 6.527737] Sending DHCP requests ., OK <6>[ 6.571808] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.35 <6>[ 6.580151] IP-Config: Complete: <6>[ 6.583669] device=eth0, hwaddr=00:19:b8:08:f1:09, ipaddr=192.168.201.35, mask=255.255.255.0, gw=192.168.201.1 <6>[ 6.594411] host=imx6q-sabrelite-lava-cbg-5, domain=lava-rack, nis-domain=(none) <6>[ 6.602551] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 6.602559] nameserver0=192.168.201.1 <6>[ 6.621488] Freeing unused kernel memory: 2048K <6>[ 6.647946] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 6.778936] udevd[107]: starting version 3.2.9 <5>[ 6.784536] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.791939] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.798986] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 6.814421] udevd[107]: specified user 'tss' unknown <27>[ 6.820261] udevd[107]: specified group 'tss' unknown <30>[ 6.827942] udevd[108]: starting eudev-3.2.9 <6>[ 7.177490] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.204214] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 <6>[ 7.224617] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.231977] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.240625] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) <6>[ 7.240694] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.245067] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.262817] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 7.270571] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <4>[ 7.272056] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.277392] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 7.286100] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.299472] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.307756] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.316798] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.324010] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.332245] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.339687] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.348745] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.356229] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.372193] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.377371] sgtl5000 0-000a: Linked as a consumer to regulator.7 <6>[ 7.387448] sgtl5000 0-000a: Linked as a consumer to regulator.8 <6>[ 7.393845] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.401100] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 7.404217] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 7.407990] sgtl5000 0-000a: sgtl5000 revision 0x11 <4>[ 7.416107] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.424459] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 7.428515] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.437986] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 7.444483] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.449795] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 7.464804] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.466231] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 0 <6>[ 7.472239] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.488766] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.496252] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.506022] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.514785] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.521839] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.530422] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.539528] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.546686] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.555124] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.562622] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.571693] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.580096] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.590037] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.598800] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.605799] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.614491] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.623663] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.630873] panel-simple panel-lvds0: Dropping the link to regulator.0 done Saving random seed: <5>[ 7.800323] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 7.896248] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-11967632/environment . /lava-11967632/environment / # /lava-11967632/bin/lava-test-runner /lava-11967632/0 /lava-11967632/bin/lava-test-runner /lava-11967632/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-11967632/0/tests/0_dmesg + cat uuid + UUID=11967632<8>[ 8.495988] _1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 8.541393] <8>[ 8.581705] <8>[ 8.622319] + set +x <8>[ 8.632145] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-11967632/environment / # . /lava-11967632/environment/lava-11967632/bin/lava-test-runner /lava-11967632/1 / # /lava-11967632/bin/lava-test-runner /lava-11967632/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-11967632/1/tests/1_bootrr + cat uuid + UUID=1196763<8>[ 9.134713] 2_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-11967632/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto backlight-lcd backlight-lvds panel-lcd panel-lvds0 /lava-11967632/1/../bin/lava-test-case <8>[ 10.216855] /lava-11967632/1/../bin/lava-test-case <8>[ 10.255442] /lava-11967632/1/../bin/lava-test-case <8>[ 10.280209] + set +x <8>[ 10.298732] / #