[Enter `^Ec?' for help] NOTICE: BL2: R-Car Gen3 Initial Program Loader(CA57) Rev.1.0.12 NOTICE: BL2: PRR is R-Car M3 ES1.0 NOTICE: BL2: Boot device is HyperFlash(80MHz) NOTICE: BL2: LCM state is CM NOTICE: BL2: AVS setting succeeded. DVFS_SetVID=0x52 NOTICE: BL2: DDR3200(rev.0.20)[COLD_BOOT]..0 NOTICE: BL2: DRAM Split is OFF NOTICE: BL2: QoS is default setting(rev.0.16) NOTICE: BL2: v1.3(release):a80bbf3 NOTICE: BL2: Built : 22:16:12, Mar 30 2017 NOTICE: BL2: Normal boot NOTICE: BL2: dst=0xe6316190 src=0x8180000 len=512(0x200) NOTICE: BL2: dst=0x43f00000 src=0x8180400 len=6144(0x1800) NOTICE: BL2: dst=0x44000000 src=0x81c0000 len=65536(0x10000) NOTICE: BL2: dst=0x44100000 src=0x8200000 len=524288(0x80000) NOTICE: BL2: dst=0x50000000 src=0x8640000 len=1048576(0x100000) U-Boot 2020.04+dfsg-2co5bv2022dev0b2 (Nov 03 2020 - 09:02:07 +0000) CPU: Renesas Electronics R8A7796 rev 1.0 Model: Renesas M3ULCB board based on r8a7796 DRAM: 1.9 GiB Bank #0: 0x048000000 - 0x07fffffff, 896 MiB Bank #1: 0x600000000 - 0x63fffffff, 1 GiB MMC: sd@ee100000: 0, sd@ee140000: 1 Loading Environment from MMC... OK In: serial@e6e88000 Out: serial@e6e88000 Err: serial@e6e88000 Net: eth0: ethernet@e6800000 Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => dhcp dhcp ethernet@e6800000 Waiting for PHY auto negotiation to complete.. done BOOTP broadcast 1 BOOTP broadcast 2 DHCP client bound to address 192.168.201.21 (260 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x68080000 11967573/tftp-deploy-g6b7vo7p/kernel/Image tftp 0x68080000 11967573/tftp-deploy-g6b7vo7p/kernel/Image Using ethernet@e6800000 device TFTP from server 192.168.201.1; our IP address is 192.168.201.21 Filename '11967573/tftp-deploy-g6b7vo7p/kernel/Image'. Load address: 0x68080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################ 7.1 MiB/s done Bytes transferred = 19307008 (1269a00 hex) => tftp 0x4a000000 11967573/tftp-deploy-g6b7vo7p/ramdisk/ramdisk.cpio.gz.uboot tftp 0x4a000000 11967573/tftp-deploy-g6b7vo7p/ramdisk/ramdisk.cpio.gz.uboot Using ethernet@e6800000 device TFTP from server 192.168.201.1; our IP address is 192.168.201.21 Filename '11967573/tftp-deploy-g6b7vo7p/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x4a000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################ 7 MiB/s done Bytes transferred = 15187650 (e7bec2 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x68000000 11967573/tftp-deploy-g6b7vo7p/dtb/r8a7796-m3ulcb.dtb tftp 0x68000000 11967573/tftp-deploy-g6b7vo7p/dtb/r8a7796-m3ulcb.dtb Using ethernet@e6800000 device TFTP from server 192.168.201.1; our IP address is 192.168.201.21 Filename '11967573/tftp-deploy-g6b7vo7p/dtb/r8a7796-m3ulcb.dtb'. Load address: 0x68000000 Loading: *#### 3.6 MiB/s done Bytes transferred = 52637 (cd9d hex) => setenv bootargs 'console=ttySC0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttySC0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => booti 0x68080000 0x4a000000 0x68000000 booti 0x68080000 0x4a000000 0x68000000 ## Loading init Ramdisk from Legacy Image at 4a000000 ... Image Name: Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 15187586 Bytes = 14.5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 68000000 Booting using the fdt blob at 0x68000000 Using Device Tree in place at 0000000068000000, end 000000006800fd9c Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x411fd073] [ 0.000000] Linux version 4.19.298-cip104 (KernelCI@build-j9713-arm64-gcc-10-defconfig-bqww4) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP PREEMPT Wed Nov 8 11:47:47 UTC 2023 [ 0.000000] Machine model: Renesas M3ULCB board based on r8a7796 [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 32 MiB at 0x000000007e000000 [ 0.000000] earlycon: scif0 at MMIO 0x00000000e6e88000 (options '115200n8') [ 0.000000] bootconsole [scif0] enabled [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000048000000-0x000000063fffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x63ffb3a40-0x63ffb51ff] [ 0.000000] Zone ranges: [ 0.000000] DMA32 [mem 0x0000000048000000-0x00000000ffffffff] [ 0.000000] Normal [mem 0x0000000100000000-0x000000063fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000048000000-0x000000007fffffff] [ 0.000000] node 0: [mem 0x0000000600000000-0x000000063fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000048000000-0x000000063fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] percpu: Embedded 22 pages/cpu s52760 r8192 d29160 u90112 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] ARM_SMCCC_ARCH_WORKAROUND_1 missing from firmware [ 0.000000] CPU features: enabling workaround for EL2 vector hardening [ 0.000000] CPU features: enabling workaround for Spectre-BHB [ 0.000000] CPU features: enabling workaround for ARM erratum 1742098 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 483840 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttySC0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] software IO TLB: mapped [mem 0x79fff000-0x7dfff000] (64MB) <6>[ 0.000000] Memory: 1799268K/1966080K available (11196K kernel code, 1382K rwdata, 4968K rodata, 1280K init, 377K bss, 134044K reserved, 32768K cma-reserved) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=6. <6>[ 0.000000] Tasks RCU enabled. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=6 <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] arch_timer: cp15 timer(s) running at 8.33MHz (virt). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1ec02923e, max_idle_ns: 440795202125 ns <6>[ 0.000003] sched_clock: 56 bits at 8MHz, resolution 120ns, wraps every 2199023255496ns <6>[ 0.008352] Console: colour dummy device 80x25 <6>[ 0.013084] Calibrating delay loop (skipped), value calculated using timer frequency.. 16.66 BogoMIPS (lpj=33333) <6>[ 0.023559] pid_max: default: 32768 minimum: 301 <6>[ 0.028453] Security Framework initialized <6>[ 0.033658] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) <6>[ 0.041487] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) <6>[ 0.048802] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes) <6>[ 0.055744] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes) <6>[ 0.064007] ASID allocator initialised with 32768 entries <6>[ 0.069725] rcu: Hierarchical SRCU implementation. <6>[ 0.075665] Detected Renesas R-Car Gen3 r8a7796 ES1.0 <6>[ 0.081862] EFI services will not be available. <6>[ 0.086874] smp: Bringing up secondary CPUs ... <6>[ 0.092035] Detected PIPT I-cache on CPU1 <6>[ 0.092074] CPU1: Booted secondary processor 0x0000000001 [0x411fd073] <3>[ 0.092383] psci: failed to boot CPU2 (-22) <3>[ 0.107825] CPU2: failed to boot: -22 <3>[ 0.112033] psci: failed to boot CPU3 (-22) <3>[ 0.116473] CPU3: failed to boot: -22 <3>[ 0.120670] psci: failed to boot CPU4 (-22) <3>[ 0.125106] CPU4: failed to boot: -22 <3>[ 0.129287] psci: failed to boot CPU5 (-22) <3>[ 0.133716] CPU5: failed to boot: -22 <6>[ 0.137659] smp: Brought up 1 node, 2 CPUs <6>[ 0.141996] SMP: Total of 2 processors activated. <6>[ 0.146947] CPU features: detected: 32-bit EL0 Support <6>[ 0.152801] CPU: All CPU(s) started at EL1 <6>[ 0.157148] alternatives: patching kernel code <6>[ 0.162622] devtmpfs: initialized <6>[ 0.170085] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.180108] futex hash table entries: 2048 (order: 5, 131072 bytes) <6>[ 0.187337] pinctrl core: initialized pinctrl subsystem <6>[ 0.194105] DMI not present or invalid. <6>[ 0.198596] NET: Registered protocol family 16 <6>[ 0.203464] audit: initializing netlink subsys (disabled) <5>[ 0.209195] audit: type=2000 audit(0.140:1): state=initialized audit_enabled=0 res=1 <6>[ 0.217183] cpuidle: using governor menu <6>[ 0.221499] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.229055] DMA: preallocated 256 KiB pool for atomic allocations <6>[ 0.236422] Serial: AMBA PL011 UART driver <6>[ 0.243125] sh-pfc e6060000.pin-controller: r8a77960_pfc support registered <6>[ 0.274383] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.282277] cryptd: max_cpu_qlen set to 1000 <6>[ 0.288518] ACPI: Interpreter disabled. <6>[ 0.295326] vgaarb: loaded <5>[ 0.298544] SCSI subsystem initialized <6>[ 0.302990] usbcore: registered new interface driver usbfs <6>[ 0.308809] usbcore: registered new interface driver hub <6>[ 0.314569] usbcore: registered new device driver usb <6>[ 0.320753] i2c-sh_mobile e60b0000.i2c: I2C adapter 7, bus speed 100000 Hz <6>[ 0.328189] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.333392] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.342754] PTP clock support registered <6>[ 0.347037] EDAC MC: Ver: 3.0.0 <6>[ 0.351254] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.358023] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.364459] VFS: Disk quotas dquot_6.6.0 <6>[ 0.368666] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 0.375882] pnp: PnP ACPI: disabled <6>[ 0.383542] NET: Registered protocol family 2 <6>[ 0.388468] IP idents hash table entries: 32768 (order: 6, 262144 bytes) <6>[ 0.396160] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes) <6>[ 0.404258] TCP established hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.411771] TCP bind hash table entries: 16384 (order: 6, 262144 bytes) <6>[ 0.418774] TCP: Hash tables configured (established 16384 bind 16384) <6>[ 0.425655] UDP hash table entries: 1024 (order: 3, 32768 bytes) <6>[ 0.431922] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes) <6>[ 0.438691] NET: Registered protocol family 1 <6>[ 0.443587] RPC: Registered named UNIX socket transport module. <6>[ 0.449794] RPC: Registered udp transport module. <6>[ 0.454741] RPC: Registered tcp transport module. <6>[ 0.459682] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.466453] Unpacking initramfs... <6>[ 0.955951] Freeing initrd memory: 14824K <6>[ 0.960501] hw perfevents: /pmu_a53: failed to probe PMU! <6>[ 0.966151] hw perfevents: /pmu_a53: failed to register PMU devices! <6>[ 0.972893] hw perfevents: enabled with armv8_cortex_a57 PMU driver, 7 counters available <6>[ 0.981573] kvm [1]: HYP mode not available <5>[ 0.988276] Initialise system trusted keyrings <6>[ 0.993155] workingset: timestamp_bits=44 max_order=19 bucket_order=0 <6>[ 1.003618] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.010315] NFS: Registering the id_resolver key type <5>[ 1.015634] Key type id_resolver registered <5>[ 1.020091] Key type id_legacy registered <6>[ 1.024356] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 1.031296] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 1.039056] 9p: Installing v9fs 9p2000 file system support <5>[ 1.046550] Key type asymmetric registered <5>[ 1.050902] Asymmetric key parser 'x509' registered <6>[ 1.056061] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244) <6>[ 1.063694] io scheduler noop registered <6>[ 1.067863] io scheduler deadline registered <6>[ 1.072482] io scheduler cfq registered (default) <6>[ 1.077431] io scheduler mq-deadline registered <6>[ 1.082200] io scheduler kyber registered <6>[ 1.092286] gpio_rcar e6050000.gpio: driving 16 GPIOs <6>[ 1.097819] gpio_rcar e6051000.gpio: driving 29 GPIOs <6>[ 1.103301] gpio_rcar e6052000.gpio: driving 15 GPIOs <6>[ 1.108765] gpio_rcar e6053000.gpio: driving 16 GPIOs <6>[ 1.114227] gpio_rcar e6054000.gpio: driving 18 GPIOs <6>[ 1.119761] gpio_rcar e6055000.gpio: driving 26 GPIOs <6>[ 1.125235] gpio_rcar e6055400.gpio: driving 32 GPIOs <6>[ 1.130692] gpio_rcar e6055800.gpio: driving 4 GPIOs <4>[ 1.138379] EINJ: ACPI disabled. <6>[ 1.149269] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 1.157524] SuperH (H)SCI(F) driver initialized <6>[ 1.162750] e6e88000.serial: ttySC0 at MMIO 0xe6e88000 (irq = 112, base_baud = 0) is a scif <6>[ 1.171393] console [ttySC0] enabled <6>[ 1.171393] console [ttySC0] enabled <6>[ 1.179176] bootconsole [scif0] disabled <6>[ 1.179176] bootconsole [scif0] disabled <6>[ 1.188223] msm_serial: driver initialized <6>[ 1.197397] loop: module loaded <6>[ 1.204519] tun: Universal TUN/TAP device driver, 1.6 <6>[ 1.210836] thunder_xcv, ver 1.0 <6>[ 1.214369] thunder_bgx, ver 1.0 <6>[ 1.217872] nicpf, ver 1.0 <6>[ 1.221264] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 1.227365] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 1.233596] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 1.240825] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.246686] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k <6>[ 1.254777] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 1.261226] sky2: driver version 1.30 <6>[ 1.266055] VFIO - User Level meta-driver version: 0.3 <6>[ 1.272468] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 1.279268] ehci-pci: EHCI PCI platform driver <6>[ 1.284001] ehci-platform: EHCI generic platform driver <6>[ 1.289758] ehci-platform ee0a0100.usb: EHCI Host Controller <6>[ 1.295706] ehci-platform ee0a0100.usb: new USB bus registered, assigned bus number 1 <6>[ 1.304106] ehci-platform ee0a0100.usb: irq 147, io mem 0xee0a0100 <6>[ 1.326035] ehci-platform ee0a0100.usb: USB 2.0 started, EHCI 1.10 <6>[ 1.332846] hub 1-0:1.0: USB hub found <6>[ 1.336878] hub 1-0:1.0: 1 port detected <6>[ 1.341317] ehci-orion: EHCI orion driver <6>[ 1.345770] ehci-exynos: EHCI EXYNOS driver <6>[ 1.350292] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 1.356744] ohci-pci: OHCI PCI platform driver <6>[ 1.361498] ohci-platform: OHCI generic platform driver <6>[ 1.367162] ohci-platform ee0a0000.usb: Generic Platform OHCI controller <6>[ 1.374141] ohci-platform ee0a0000.usb: new USB bus registered, assigned bus number 2 <6>[ 1.382347] ohci-platform ee0a0000.usb: irq 147, io mem 0xee0a0000 <6>[ 1.476447] hub 2-0:1.0: USB hub found <6>[ 1.480478] hub 2-0:1.0: 1 port detected <6>[ 1.484896] ohci-exynos: OHCI EXYNOS driver <6>[ 1.489851] usbcore: registered new interface driver usb-storage <6>[ 1.498272] i2c /dev entries driver <6>[ 1.509756] cs2000-cp 2-004f: revision - C1 <6>[ 1.514264] i2c-rcar e6510000.i2c: probed <6>[ 1.524380] i2c-rcar e66d8000.i2c: probed <6>[ 1.534210] rcar_gen3_thermal e6198000.thermal: TSC0: Loaded 2 trip points <6>[ 1.545479] rcar_gen3_thermal e6198000.thermal: TSC1: Loaded 2 trip points <6>[ 1.556117] rcar_gen3_thermal e6198000.thermal: TSC2: Loaded 2 trip points <4>[ 1.565556] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 1499999 KHz <4>[ 1.573244] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 1500000 KHz <6>[ 1.582772] sdhci: Secure Digital Host Controller Interface driver <6>[ 1.589217] sdhci: Copyright(c) Pierre Ossman <6>[ 1.594594] renesas_sdhi_internal_dmac ee100000.sd: Got CD GPIO <6>[ 1.601332] renesas_sdhi_internal_dmac ee140000.sd: Linked as a consumer to regulator.2 <6>[ 1.609631] renesas_sdhi_internal_dmac ee140000.sd: Linked as a consumer to regulator.1 <6>[ 1.666326] renesas_sdhi_internal_dmac ee140000.sd: mmc0 base at 0xee140000 max clock rate 200 MHz <6>[ 1.675697] Synopsys Designware Multimedia Card Interface Driver <6>[ 1.682809] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 1.689896] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 1.696935] usbcore: registered new interface driver usbhid <6>[ 1.702800] usbhid: USB HID core driver <6>[ 1.709326] NET: Registered protocol family 17 <6>[ 1.714183] 9pnet: Installing 9P2000 support <5>[ 1.718828] Key type dns_resolver registered <6>[ 1.723834] registered taskstats version 1 <5>[ 1.728403] Loading compiled-in X.509 certificates <6>[ 1.740043] renesas_irqc e61c0000.interrupt-controller: driving 6 irqs <6>[ 1.751876] bd9571mwv 7-0030: Device: BD9571MWV rev. 1 <6>[ 1.766124] renesas_sdhi_internal_dmac ee100000.sd: Got CD GPIO <6>[ 1.772409] renesas_sdhi_internal_dmac ee100000.sd: Linked as a consumer to regulator.3 <6>[ 1.780722] renesas_sdhi_internal_dmac ee100000.sd: Linked as a consumer to regulator.4 <6>[ 1.826028] mmc0: new HS200 MMC card at address 0001 <6>[ 1.831621] mmcblk0: mmc0:0001 R1J55A 7.28 GiB <6>[ 1.836599] mmcblk0boot0: mmc0:0001 R1J55A partition 1 8.00 MiB <6>[ 1.837386] renesas_sdhi_internal_dmac ee100000.sd: mmc1 base at 0xee100000 max clock rate 200 MHz <6>[ 1.842968] mmcblk0boot1: mmc0:0001 R1J55A partition 2 8.00 MiB <4>[ 1.855756] rcar-dmac e6700000.dma-controller: ignoring dependency for device, assuming no driver <6>[ 1.867446] mmcblk0rpmb: mmc0:0001 R1J55A partition 3 4.00 MiB, chardev (239:0) <4>[ 1.869940] rcar-dmac e7300000.dma-controller: ignoring dependency for device, assuming no driver <4>[ 1.886831] rcar-dmac e7310000.dma-controller: ignoring dependency for device, assuming no driver <4>[ 1.897784] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 1.898742] rcar-dmac ec700000.dma-controller: ignoring dependency for device, assuming no driver <4>[ 1.906289] GPT:7812499 != 15269887 <4>[ 1.918591] GPT:Alternate GPT header not at the end of the disk. <4>[ 1.924395] rcar-dmac ec720000.dma-controller: ignoring dependency for device, assuming no driver <4>[ 1.925448] GPT:7812499 != 15269887 <4>[ 1.937169] ravb e6800000.ethernet: ignoring dependency for device, assuming no driver <4>[ 1.938882] GPT: Use GNU Parted to correct GPT errors. <6>[ 1.951408] mmcblk0: p1 p2 p3 <6>[ 1.961325] ravb e6800000.ethernet eth0: Base address at 0xe6800000, 8a:45:64:24:29:76, IRQ 109. <6>[ 1.971394] input: keyboard as /devices/platform/keyboard/input/input0 <6>[ 1.978590] hctosys: unable to open rtc device (rtc0) <6>[ 2.051189] mmc1: new ultra high speed SDR50 SDHC card at address 0001 <6>[ 2.058491] mmcblk1: mmc1:0001 SD 14.8 GiB <6>[ 2.062779] Micrel KSZ9031 Gigabit PHY e6800000.ethernet-ffffffff:00: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=e6800000.ethernet-ffffffff:00, irq=164) <4>[ 2.072232] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 2.086588] GPT:7812499 != 30965759 <4>[ 2.090341] GPT:Alternate GPT header not at the end of the disk. <4>[ 2.096613] GPT:7812499 != 30965759 <4>[ 2.100365] GPT: Use GNU Parted to correct GPT errors. <6>[ 2.105779] mmcblk1: p1 p2 p3 <6>[ 3.635928] ravb e6800000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <5>[ 3.662030] Sending DHCP requests .., OK <6>[ 6.418235] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.21 <6>[ 6.426497] IP-Config: Complete: <6>[ 6.429981] device=eth0, hwaddr=8a:45:64:24:29:76, ipaddr=192.168.201.21, mask=255.255.255.0, gw=192.168.201.1 <6>[ 6.440676] host=r8a7796-m3ulcb-cbg-1, domain=lava-rack, nis-domain=(none) <6>[ 6.448243] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 6.448245] nameserver0=192.168.201.1 <6>[ 6.460458] ALSA device list: <6>[ 6.463702] No soundcards found. <6>[ 6.468372] Freeing unused kernel memory: 1280K <6>[ 6.473232] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 6.523939] udevd[1737]: starting version 3.2.9 <5>[ 6.529374] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.536245] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.543137] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 6.552726] udevd[1737]: specified user 'tss' unknown <27>[ 6.558224] udevd[1737]: specified group 'tss' unknown <30>[ 6.564777] udevd[1738]: starting eudev-3.2.9 <4>[ 6.765930] rcar-fcp fe9af000.fcp: ignoring dependency for device, assuming no driver <6>[ 6.776863] media: Linux media interface: v0.10 <6>[ 6.795495] videodev: Linux video capture interface: v2.00 <6>[ 6.807013] rcar_sound ec500000.sound: probed <4>[ 6.811933] rcar-fcp fea27000.fcp: ignoring dependency for device, assuming no driver <4>[ 6.826415] rcar-fcp fea2f000.fcp: ignoring dependency for device, assuming no driver <4>[ 6.840027] rcar-fcp fea37000.fcp: ignoring dependency for device, assuming no driver <6>[ 6.863091] rcar_fdp1 fe940000.fdp1: Device registered as /dev/video0 <6>[ 6.943534] asoc-simple-card sound: ak4613-hifi <-> ec500000.sound mapping ok <6>[ 6.979244] rcar-dw-hdmi fead0000.hdmi: Detected HDMI TX controller v2.01a with HDCP (DWC HDMI 2.0 TX PHY) <4>[ 6.982721] asoc-simple-card sound: ASoC: no DMI vendor name! <6>[ 6.992863] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 7.015191] [drm] No driver support for vblank timestamp query. <6>[ 7.021888] rcar-dw-hdmi fead0000.hdmi: registered DesignWare HDMI I2C bus driver <6>[ 7.032532] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 7.040760] [drm] No driver support for vblank timestamp query. <6>[ 7.050637] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 7.058666] [drm] No driver support for vblank timestamp query. <6>[ 7.267438] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 7.276182] [drm] No driver support for vblank timestamp query. <6>[ 7.284862] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 7.291808] [drm] No driver support for vblank timestamp query. <6>[ 7.299647] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 7.306570] [drm] No driver support for vblank timestamp query. done Saving random seed: <5>[ 7.587082] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 7.623633] random: dropbear: uninitialized urandom read (32 bytes read) <6>[ 7.650171] NET: Registered protocol family 10 <6>[ 7.655552] Segment Routing with IPv6 OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-11967573/environment . /lava-11967573/environment / # /lava-11967573/bin/lava-test-runner /lava-11967573/0 /lava-11967573/bin/lava-test-runner /lava-11967573/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava<8>[ 8.204446] -11967573/0/tests/0_dmesg + cat uuid + UUID=11967573_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 8.225205] <8>[ 8.245161] <8>[ 8.265217] + set +x <8>[ 8.274687] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-11967573/environment / # . /lava-11967573/environment/lava-11967573/bin/lava-test-runner /lava-11967573/1 / # /lava-11967573/bin/lava-test-runner /lava-11967573/1 + export 'TESTRUN_ID=1_bootrr' + cd /lav<8>[ 8.719176] a-11967573/1/tests/1_bootrr + cat uuid + UUID=11967573_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-11967573/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto feb00000.display /lava-11967573/1/../bin/lava-test-case <8>[ 9.745355] /lava-11967573/1/../bin/lava-test-case <8>[ 10.766707] /lava-11967573/1/../bin/lava-test-case <8>[ 10.780740] + set +x <8>[ 10.792777] / #