[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.37 (7 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 12636662/tftp-deploy-oqv9cj__/kernel/zImage tftp 0x10000000 12636662/tftp-deploy-oqv9cj__/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '12636662/tftp-deploy-oqv9cj__/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########### 14.3 MiB/s done Bytes transferred = 8737280 (855200 hex) => tftp 0x14000000 12636662/tftp-deploy-oqv9cj__/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 12636662/tftp-deploy-oqv9cj__/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '12636662/tftp-deploy-oqv9cj__/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################ 14.1 MiB/s done Bytes transferred = 13338481 (cb8771 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 12636662/tftp-deploy-oqv9cj__/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 12636662/tftp-deploy-oqv9cj__/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '12636662/tftp-deploy-oqv9cj__/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 6.6 MiB/s done Bytes transferred = 41822 (a35e hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x855200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 13338417 Bytes = 12.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d35d Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.306-cip106 (KernelCI@build-j90056-arm-gcc-10-multi-v7-defconfig-2zhxh) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Fri Jan 26 05:33:58 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] percpu: Embedded 16 pages/cpu s36748 r8192 d20596 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 939136K/1048576K available (12288K kernel code, 1597K rwdata, 4688K rodata, 2048K init, 394K bss, 43904K reserved, 65536K cma-reserved, 196608K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1598 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 395 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008444] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.021348] Console: colour dummy device 80x30 <6>[ 0.023230] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.033646] CPU: Testing write buffer coherency: ok <6>[ 0.038779] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.044077] pid_max: default: 32768 minimum: 301 <6>[ 0.049082] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.055845] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.064006] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.069748] Setting up static identity map for 0x10300000 - 0x103000a0 <6>[ 0.077446] rcu: Hierarchical SRCU implementation. <6>[ 0.083978] EFI services will not be available. <6>[ 0.086230] smp: Bringing up secondary CPUs ... <6>[ 0.091493] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.091500] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.102844] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.102849] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.114030] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.114035] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.124483] smp: Brought up 1 node, 4 CPUs <6>[ 0.128739] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.135156] CPU: All CPU(s) started in SVC mode. <6>[ 0.141117] devtmpfs: initialized <6>[ 0.150562] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.156010] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.165763] futex hash table entries: 1024 (order: 4, 65536 bytes) <6>[ 0.175297] pinctrl core: initialized pinctrl subsystem <6>[ 0.179591] DMI not present or invalid. <6>[ 0.182824] NET: Registered protocol family 16 <6>[ 0.190196] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.196817] cpuidle: using governor menu <6>[ 0.198841] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.213824] vdd1p1: supplied by regulator-dummy <6>[ 0.216282] vdd3p0: supplied by regulator-dummy <6>[ 0.221021] vdd2p5: supplied by regulator-dummy <6>[ 0.225860] vddarm: supplied by regulator-dummy <6>[ 0.230776] vddpu: supplied by regulator-dummy <6>[ 0.235176] vddsoc: supplied by regulator-dummy <6>[ 0.253889] No ATAGs? <6>[ 0.254051] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.262011] hw-breakpoint: maximum watchpoint size is 4 bytes. <4>[ 0.271515] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory <6>[ 0.278396] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver <6>[ 0.290332] Serial: AMBA PL011 UART driver <6>[ 0.294183] console [pstore-1] enabled <6>[ 0.296026] pstore: Registered ramoops as persistent store backend <6>[ 0.302278] ramoops: attached 0x10000@0x30000000, ecc: 0/0 <6>[ 0.330840] mxs-dma 110000.dma-apbh: initialized <6>[ 0.340313] vgaarb: loaded <5>[ 0.341237] SCSI subsystem initialized <6>[ 0.344829] usbcore: registered new interface driver usbfs <6>[ 0.350295] usbcore: registered new interface driver hub <6>[ 0.355792] usbcore: registered new device driver usb <6>[ 0.362289] i2c i2c-0: IMX I2C adapter registered <6>[ 0.366033] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.372139] i2c i2c-1: IMX I2C adapter registered <6>[ 0.376553] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.382487] i2c i2c-2: IMX I2C adapter registered <6>[ 0.387085] i2c i2c-2: can't use DMA, using PIO instead. <6>[ 0.394188] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.397862] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.407271] PTP clock support registered <6>[ 0.411649] EDAC MC: Ver: 3.0.0 <6>[ 0.417657] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.481799] NET: Registered protocol family 2 <6>[ 0.484024] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.491542] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) <6>[ 0.498515] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.505830] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) <6>[ 0.512610] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.519291] UDP hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.525278] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.532041] NET: Registered protocol family 1 <6>[ 0.537015] RPC: Registered named UNIX socket transport module. <6>[ 0.542672] RPC: Registered udp transport module. <6>[ 0.547603] RPC: Registered tcp transport module. <6>[ 0.552577] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.559745] Trying to unpack rootfs image as initramfs... <6>[ 1.676875] Freeing initrd memory: 13028K <4>[ 1.678892] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 1.686075] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 1.696026] Initialise system trusted keyrings <6>[ 1.699125] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 1.711437] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.715309] NFS: Registering the id_resolver key type <5>[ 1.720058] Key type id_resolver registered <5>[ 1.724424] Key type id_legacy registered <6>[ 1.728739] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 1.735513] Key type asymmetric registered <5>[ 1.737684] Asymmetric key parser 'x509' registered <6>[ 1.742828] bounce: pool size: 64 pages <6>[ 1.746912] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 1.754549] io scheduler noop registered <6>[ 1.758718] io scheduler deadline registered <6>[ 1.763368] io scheduler cfq registered (default) <6>[ 1.768204] io scheduler mq-deadline registered <6>[ 1.772972] io scheduler kyber registered <6>[ 1.799319] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 1.803841] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 1.811012] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 1.818283] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 1.838562] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set <6>[ 1.841953] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc <4>[ 1.849801] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set <6>[ 1.855976] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 <4>[ 1.863940] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <4>[ 1.867688] PU : no governor for states <6>[ 1.873510] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 1.877575] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc <6>[ 1.951415] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 1.958767] SuperH (H)SCI(F) driver initialized <6>[ 1.961607] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX <6>[ 1.970364] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX <6>[ 1.981344] console [ttymxc1] enabled <6>[ 1.981344] console [ttymxc1] enabled <6>[ 1.986327] bootconsole [ec_imx21] disabled <6>[ 1.986327] bootconsole [ec_imx21] disabled <6>[ 1.996429] msm_serial: driver initialized <6>[ 2.002681] STMicroelectronics ASC driver initialized <6>[ 2.009850] STM32 USART driver initialized <4>[ 2.025039] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.033743] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.040724] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.047476] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.056515] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.063685] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.078319] brd: module loaded <6>[ 2.088239] loop: module loaded <6>[ 2.094830] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 2.103048] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 2.111338] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 2.119809] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <6>[ 2.130589] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 2.137878] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 2.146938] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 2.157776] scsi host0: ahci-imx <6>[ 2.161842] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 <6>[ 2.180864] CAN device driver interface <6>[ 2.186222] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 2.193313] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator <6>[ 2.202294] fec 2188000.ethernet: Linked as a consumer to regulator.0 <6>[ 2.211399] pps pps0: new PPS source ptp0 <6>[ 2.242080] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 2.249496] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 2.255596] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.261857] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 2.269099] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 2.280807] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 2.288529] usbcore: registered new interface driver pegasus <6>[ 2.294493] usbcore: registered new interface driver asix <6>[ 2.300207] usbcore: registered new interface driver ax88179_178a <6>[ 2.306598] usbcore: registered new interface driver cdc_ether <6>[ 2.312762] usbcore: registered new interface driver smsc75xx <6>[ 2.318837] usbcore: registered new interface driver smsc95xx <6>[ 2.324879] usbcore: registered new interface driver net1080 <6>[ 2.330853] usbcore: registered new interface driver cdc_subset <6>[ 2.337069] usbcore: registered new interface driver zaurus <6>[ 2.342990] usbcore: registered new interface driver cdc_ncm <6>[ 2.351822] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 2.358648] ehci-pci: EHCI PCI platform driver <6>[ 2.363400] ehci-platform: EHCI generic platform driver <6>[ 2.369204] ehci-orion: EHCI orion driver <6>[ 2.373701] SPEAr-ehci: EHCI SPEAr driver <6>[ 2.378182] ehci-st: EHCI STMicroelectronics driver <6>[ 2.383506] ehci-exynos: EHCI EXYNOS driver <6>[ 2.388183] ehci-atmel: EHCI Atmel driver <6>[ 2.392641] tegra-ehci: Tegra EHCI driver <6>[ 2.397135] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 2.403616] ohci-pci: OHCI PCI platform driver <6>[ 2.408383] ohci-platform: OHCI generic platform driver <6>[ 2.414139] SPEAr-ohci: OHCI SPEAr driver <6>[ 2.418623] ohci-st: OHCI STMicroelectronics driver <6>[ 2.423950] ohci-atmel: OHCI Atmel driver <6>[ 2.429234] usbcore: registered new interface driver usb-storage <6>[ 2.437816] imx_usb 2184000.usb: Linked as a consumer to regulator.9 <6>[ 2.449814] imx_usb 2184200.usb: Linked as a consumer to regulator.14 <6>[ 2.459941] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 2.465111] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 2.497687] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 2.499167] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 2.504018] hub 1-0:1.0: USB hub found <6>[ 2.509073] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 2.513093] hub 1-0:1.0: 1 port detected <6>[ 2.519602] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 2.530012] i2c /dev entries driver <6>[ 2.549418] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) <6>[ 2.560759] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.567208] sdhci: Copyright(c) Pierre Ossman <6>[ 2.574105] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.582367] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.589177] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO <6>[ 2.594611] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO <6>[ 2.600145] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.637862] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA <6>[ 2.645868] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO <6>[ 2.651408] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.691384] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA <6>[ 2.702860] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 2.710187] usbcore: registered new interface driver usbhid <6>[ 2.716067] usbhid: USB HID core driver <6>[ 2.726093] NET: Registered protocol family 10 <6>[ 2.731922] mmc0: new high speed SDHC card at address e624 <6>[ 2.731948] Segment Routing with IPv6 <6>[ 2.741727] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.748605] NET: Registered protocol family 17 <6>[ 2.749282] mmcblk0: mmc0:e624 SL16G 14.8 GiB <6>[ 2.753338] can: controller area network core (rev 20170425 abi 9) <6>[ 2.764640] NET: Registered protocol family 29 <6>[ 2.769386] can: raw protocol (rev 20170425) <6>[ 2.773927] can: broadcast manager protocol (rev 20170425 t) <6>[ 2.779876] can: netlink gateway (rev 20170425) max_hops=1 <5>[ 2.786070] Key type dns_resolver registered <6>[ 2.791665] cpu cpu0: Linked as a consumer to regulator.4 <6>[ 2.797392] cpu cpu0: Linked as a consumer to regulator.5 <6>[ 2.803157] cpu cpu0: Linked as a consumer to regulator.6 <6>[ 2.807698] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 2.809652] ThumbEE CPU extension supported. <5>[ 2.820194] Registering SWP/SWPB emulation handler <5>[ 2.825993] Loading compiled-in X.509 certificates <6>[ 2.832878] pstore: Using compression: deflate <6>[ 2.851260] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.858827] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.867359] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.874967] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.883647] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.892335] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.899483] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.907356] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.916391] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.923648] panel-simple panel-lvds0: Dropping the link to regulator.0 <4>[ 2.932289] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 2.939989] GPT:7812499 != 31116287 <4>[ 2.943742] GPT:Alternate GPT header not at the end of the disk. <4>[ 2.950025] GPT:7812499 != 31116287 <4>[ 2.953777] GPT: Use GNU Parted to correct GPT errors. <6>[ 2.959227] mmcblk0: p1 p2 p3 <6>[ 2.962729] imx_thermal tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <6>[ 2.973322] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.980732] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.989046] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.996501] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.005052] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.013747] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.022381] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.030311] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.039349] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.048655] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.056436] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.063970] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.072199] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.079773] hub 1-1:1.0: USB hub found <6>[ 3.083854] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.092406] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.101090] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.108035] hub 1-1:1.0: 3 ports detected <6>[ 3.112361] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.120307] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.129350] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.136495] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.144211] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.151751] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.159919] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.167384] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.175874] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.184554] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.191523] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 3.199954] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <4>[ 3.207509] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.216560] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.223698] hctosys: unable to open rtc device (rtc0) <6>[ 3.223708] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.237238] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.244641] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.252946] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.260411] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.268969] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.277628] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.284586] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.292349] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.301369] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.308488] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.358259] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 3.373207] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 6.478335] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 6.497696] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 6.527742] Sending DHCP requests ., OK <6>[ 6.571888] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.37 <6>[ 6.580234] IP-Config: Complete: <6>[ 6.583754] device=eth0, hwaddr=00:19:b8:08:f0:fd, ipaddr=192.168.201.37, mask=255.255.255.0, gw=192.168.201.1 <6>[ 6.594501] host=imx6q-sabrelite-lava-cbg-7, domain=lava-rack, nis-domain=(none) <6>[ 6.602642] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 6.602651] nameserver0=192.168.201.1 <6>[ 6.621480] Freeing unused kernel memory: 2048K <6>[ 6.658011] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 6.798625] udevd[107]: starting version 3.2.9 <5>[ 6.804161] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.811183] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.818092] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 6.831832] udevd[107]: specified user 'tss' unknown <27>[ 6.837268] udevd[107]: specified group 'tss' unknown <30>[ 6.844643] udevd[108]: starting eudev-3.2.9 <6>[ 7.172064] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.179783] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 <6>[ 7.186873] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.194358] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) <6>[ 7.195725] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.210512] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 7.216817] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <4>[ 7.219692] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.224755] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.233139] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.247405] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.249903] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 7.254260] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <4>[ 7.262422] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.276269] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.283474] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.291655] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.299069] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.307882] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.315347] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 7.339088] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 7.360970] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 7.367362] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 7.374634] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 0 <4>[ 7.383130] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.391872] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.399591] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.408467] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.417546] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.425345] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.433566] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.441791] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.450405] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.458164] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.467173] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.467929] sgtl5000 0-000a: Linked as a consumer to regulator.7 <6>[ 7.482159] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.489109] sgtl5000 0-000a: Linked as a consumer to regulator.8 <6>[ 7.495557] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.503857] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.512948] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.520265] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.528456] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 7.528826] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.541171] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.572775] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 7.635157] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.644384] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.653503] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.662228] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.672165] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.680456] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.689586] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.696896] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.705242] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.712808] pwm-backlight backlight-lcd: Dropping the link to regulator.8 done Saving random seed: <5>[ 7.929579] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 8.033405] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-12636662/environment . /lava-12636662/environment / # /lava-12636662/bin/lava-test-runner /lava-12636662/0 /lava-12636662/bin/lava-test-runner /lava-12636662/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-12636662/0/tests/0_dmesg + cat uuid + <8>[ 8.640327] UUID=12636662_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 8.684678] <8>[ 8.725514] <8>[ 8.766308] + set +x <8>[ 8.776154] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-12636662/environment / # . /lava-12636662/environment/lava-12636662/bin/lava-test-runner /lava-12636662/1 / # /lava-12636662/bin/lava-test-runner /lava-12636662/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-12636662/1/tests/1_bootrr + cat uuid + UUID=1263666<8>[ 9.275755] 2_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-12636662/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto backlight-lvds panel-lcd panel-lvds0 backlight-lcd /lava-12636662/1/../bin/lava-test-case <8>[ 10.357997] /lava-12636662/1/../bin/lava-test-case <8>[ 10.396675] /lava-12636662/1/../bin/lava-test-case <8>[ 10.421435] + set +x <8>[ 10.439993] / #