[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.35 (8 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 12543572/tftp-deploy-3qjrjfkw/kernel/zImage tftp 0x10000000 12543572/tftp-deploy-3qjrjfkw/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '12543572/tftp-deploy-3qjrjfkw/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########### 14.5 MiB/s done Bytes transferred = 8737280 (855200 hex) => tftp 0x14000000 12543572/tftp-deploy-3qjrjfkw/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 12543572/tftp-deploy-3qjrjfkw/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '12543572/tftp-deploy-3qjrjfkw/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################### 14.3 MiB/s done Bytes transferred = 9415066 (8fa99a hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 12543572/tftp-deploy-3qjrjfkw/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 12543572/tftp-deploy-3qjrjfkw/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '12543572/tftp-deploy-3qjrjfkw/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 6.6 MiB/s done Bytes transferred = 41822 (a35e hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/12543572/extract-nfsrootfs-f0jtrhn8,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/12543572/extract-nfsrootfs-f0jtrhn8,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x855200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 9415002 Bytes = 9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d35d Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.305-cip106 (KernelCI@build-j77915-arm-gcc-10-multi-v7-defconfig-qcx8m) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Tue Jan 16 03:09:25 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] percpu: Embedded 16 pages/cpu s36748 r8192 d20596 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/12543572/extract-nfsrootfs-f0jtrhn8,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 942968K/1048576K available (12288K kernel code, 1597K rwdata, 4688K rodata, 2048K init, 394K bss, 40072K reserved, 65536K cma-reserved, 196608K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1598 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 395 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000006] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008444] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.021322] Console: colour dummy device 80x30 <6>[ 0.023204] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.033621] CPU: Testing write buffer coherency: ok <6>[ 0.038755] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.044051] pid_max: default: 32768 minimum: 301 <6>[ 0.049056] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.055820] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.063986] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.069723] Setting up static identity map for 0x10300000 - 0x103000a0 <6>[ 0.077420] rcu: Hierarchical SRCU implementation. <6>[ 0.083993] EFI services will not be available. <6>[ 0.086246] smp: Bringing up secondary CPUs ... <6>[ 0.091512] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.091518] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.102854] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.102860] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.114043] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.114050] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.124501] smp: Brought up 1 node, 4 CPUs <6>[ 0.128755] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.135171] CPU: All CPU(s) started in SVC mode. <6>[ 0.141129] devtmpfs: initialized <6>[ 0.150967] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.156424] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.166173] futex hash table entries: 1024 (order: 4, 65536 bytes) <6>[ 0.175697] pinctrl core: initialized pinctrl subsystem <6>[ 0.179985] DMI not present or invalid. <6>[ 0.183211] NET: Registered protocol family 16 <6>[ 0.190540] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.197166] cpuidle: using governor menu <6>[ 0.199210] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.214104] vdd1p1: supplied by regulator-dummy <6>[ 0.216569] vdd3p0: supplied by regulator-dummy <6>[ 0.221299] vdd2p5: supplied by regulator-dummy <6>[ 0.226139] vddarm: supplied by regulator-dummy <6>[ 0.231042] vddpu: supplied by regulator-dummy <6>[ 0.235456] vddsoc: supplied by regulator-dummy <6>[ 0.254009] No ATAGs? <6>[ 0.254155] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.262115] hw-breakpoint: maximum watchpoint size is 4 bytes. <4>[ 0.271607] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory <6>[ 0.278488] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver <6>[ 0.290396] Serial: AMBA PL011 UART driver <6>[ 0.294230] console [pstore-1] enabled <6>[ 0.296095] pstore: Registered ramoops as persistent store backend <6>[ 0.302341] ramoops: attached 0x10000@0x30000000, ecc: 0/0 <6>[ 0.330739] mxs-dma 110000.dma-apbh: initialized <6>[ 0.340193] vgaarb: loaded <5>[ 0.341125] SCSI subsystem initialized <6>[ 0.344710] usbcore: registered new interface driver usbfs <6>[ 0.350138] usbcore: registered new interface driver hub <6>[ 0.355656] usbcore: registered new device driver usb <6>[ 0.362213] i2c i2c-0: IMX I2C adapter registered <6>[ 0.365911] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.372022] i2c i2c-1: IMX I2C adapter registered <6>[ 0.376435] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.382372] i2c i2c-2: IMX I2C adapter registered <6>[ 0.386963] i2c i2c-2: can't use DMA, using PIO instead. <6>[ 0.394057] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.397741] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.407150] PTP clock support registered <6>[ 0.411536] EDAC MC: Ver: 3.0.0 <6>[ 0.417556] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.481212] NET: Registered protocol family 2 <6>[ 0.483434] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.490962] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) <6>[ 0.497928] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.505247] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) <6>[ 0.512029] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.518712] UDP hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.524690] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.531454] NET: Registered protocol family 1 <6>[ 0.536433] RPC: Registered named UNIX socket transport module. <6>[ 0.542085] RPC: Registered udp transport module. <6>[ 0.547011] RPC: Registered tcp transport module. <6>[ 0.551990] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.559139] Trying to unpack rootfs image as initramfs... <6>[ 1.287540] Freeing initrd memory: 9196K <4>[ 1.289462] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 1.296776] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 1.306631] Initialise system trusted keyrings <6>[ 1.309656] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 1.322039] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.325920] NFS: Registering the id_resolver key type <5>[ 1.330663] Key type id_resolver registered <5>[ 1.335027] Key type id_legacy registered <6>[ 1.339344] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 1.346118] Key type asymmetric registered <5>[ 1.348285] Asymmetric key parser 'x509' registered <6>[ 1.353426] bounce: pool size: 64 pages <6>[ 1.357511] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 1.365151] io scheduler noop registered <6>[ 1.369318] io scheduler deadline registered <6>[ 1.373961] io scheduler cfq registered (default) <6>[ 1.378808] io scheduler mq-deadline registered <6>[ 1.383574] io scheduler kyber registered <6>[ 1.409615] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 1.414139] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 1.421361] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 1.428582] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 1.448648] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set <6>[ 1.452045] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc <4>[ 1.459887] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set <6>[ 1.466063] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 <4>[ 1.474025] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <4>[ 1.477577] PU : no governor for states <6>[ 1.483589] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 1.487679] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc <6>[ 1.543684] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 1.550985] SuperH (H)SCI(F) driver initialized <6>[ 1.553829] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX <6>[ 1.562590] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX <6>[ 1.573563] console [ttymxc1] enabled <6>[ 1.573563] console [ttymxc1] enabled <6>[ 1.578565] bootconsole [ec_imx21] disabled <6>[ 1.578565] bootconsole [ec_imx21] disabled <6>[ 1.588690] msm_serial: driver initialized <6>[ 1.594865] STMicroelectronics ASC driver initialized <6>[ 1.602046] STM32 USART driver initialized <4>[ 1.617181] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 1.625895] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 1.632876] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 1.639655] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 1.648685] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 1.655801] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 1.670588] brd: module loaded <6>[ 1.680574] loop: module loaded <6>[ 1.687132] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 1.695358] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 1.703667] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 1.712127] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <6>[ 1.722913] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 1.730200] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 1.739279] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 1.750132] scsi host0: ahci-imx <6>[ 1.754201] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 <6>[ 1.773023] CAN device driver interface <6>[ 1.778414] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 1.785453] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator <6>[ 1.794415] fec 2188000.ethernet: Linked as a consumer to regulator.0 <6>[ 1.803509] pps pps0: new PPS source ptp0 <6>[ 1.825303] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 1.832714] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 1.838837] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 1.845075] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 1.852320] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.863973] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 1.871701] usbcore: registered new interface driver pegasus <6>[ 1.877688] usbcore: registered new interface driver asix <6>[ 1.883391] usbcore: registered new interface driver ax88179_178a <6>[ 1.889805] usbcore: registered new interface driver cdc_ether <6>[ 1.895948] usbcore: registered new interface driver smsc75xx <6>[ 1.902021] usbcore: registered new interface driver smsc95xx <6>[ 1.908083] usbcore: registered new interface driver net1080 <6>[ 1.914040] usbcore: registered new interface driver cdc_subset <6>[ 1.920280] usbcore: registered new interface driver zaurus <6>[ 1.926188] usbcore: registered new interface driver cdc_ncm <6>[ 1.935010] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 1.941839] ehci-pci: EHCI PCI platform driver <6>[ 1.946589] ehci-platform: EHCI generic platform driver <6>[ 1.952398] ehci-orion: EHCI orion driver <6>[ 1.956899] SPEAr-ehci: EHCI SPEAr driver <6>[ 1.961395] ehci-st: EHCI STMicroelectronics driver <6>[ 1.966726] ehci-exynos: EHCI EXYNOS driver <6>[ 1.971385] ehci-atmel: EHCI Atmel driver <6>[ 1.975840] tegra-ehci: Tegra EHCI driver <6>[ 1.980365] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 1.986844] ohci-pci: OHCI PCI platform driver <6>[ 1.991619] ohci-platform: OHCI generic platform driver <6>[ 1.997374] SPEAr-ohci: OHCI SPEAr driver <6>[ 2.001860] ohci-st: OHCI STMicroelectronics driver <6>[ 2.007183] ohci-atmel: OHCI Atmel driver <6>[ 2.012456] usbcore: registered new interface driver usb-storage <6>[ 2.020996] imx_usb 2184000.usb: Linked as a consumer to regulator.9 <6>[ 2.033181] imx_usb 2184200.usb: Linked as a consumer to regulator.14 <6>[ 2.043343] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 2.048539] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 2.077597] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 2.083981] hub 1-0:1.0: USB hub found <6>[ 2.088064] hub 1-0:1.0: 1 port detected <6>[ 2.089166] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 2.097994] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 2.098494] i2c /dev entries driver <6>[ 2.104532] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 2.122576] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) <6>[ 2.133849] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.140325] sdhci: Copyright(c) Pierre Ossman <6>[ 2.147179] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.155420] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.162229] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO <6>[ 2.167683] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO <6>[ 2.173197] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.213025] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA <6>[ 2.221067] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO <6>[ 2.226580] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.266387] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA <6>[ 2.277771] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 2.285025] usbcore: registered new interface driver usbhid <6>[ 2.290894] usbhid: USB HID core driver <6>[ 2.300904] NET: Registered protocol family 10 <6>[ 2.306744] Segment Routing with IPv6 <6>[ 2.310808] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.317591] NET: Registered protocol family 17 <6>[ 2.322332] can: controller area network core (rev 20170425 abi 9) <6>[ 2.328893] NET: Registered protocol family 29 <6>[ 2.329874] mmc0: new high speed SDHC card at address 0001 <6>[ 2.333609] can: raw protocol (rev 20170425) <6>[ 2.341052] mmcblk0: mmc0:0001 SD 14.6 GiB <6>[ 2.343913] can: broadcast manager protocol (rev 20170425 t) <6>[ 2.354341] can: netlink gateway (rev 20170425) max_hops=1 <5>[ 2.360556] Key type dns_resolver registered <6>[ 2.366158] cpu cpu0: Linked as a consumer to regulator.4 <6>[ 2.371907] cpu cpu0: Linked as a consumer to regulator.5 <6>[ 2.377585] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 2.384386] cpu cpu0: Linked as a consumer to regulator.6 <6>[ 2.390885] ThumbEE CPU extension supported. <5>[ 2.395462] Registering SWP/SWPB emulation handler <5>[ 2.401686] Loading compiled-in X.509 certificates <6>[ 2.408365] pstore: Using compression: deflate <4>[ 2.411212] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 2.420828] GPT:7812499 != 30560255 <4>[ 2.424585] GPT:Alternate GPT header not at the end of the disk. <6>[ 2.426363] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <4>[ 2.430895] GPT:7812499 != 30560255 <4>[ 2.430898] GPT: Use GNU Parted to correct GPT errors. <6>[ 2.430952] mmcblk0: p1 p2 p3 <6>[ 2.438332] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.459347] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.466877] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.475542] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.484224] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.491171] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.499004] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.508023] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.515126] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.523647] imx_thermal tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <6>[ 2.534139] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.541546] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.549853] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.557306] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.565841] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.574527] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.581512] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.589321] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.598359] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.605536] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.613315] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.620826] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.629001] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.636570] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.645128] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.653807] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.660864] hub 1-1:1.0: USB hub found <6>[ 2.664932] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.672750] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.681784] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.688892] hub 1-1:1.0: 3 ports detected <6>[ 2.693223] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.701718] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 2.708712] hctosys: unable to open rtc device (rtc0) <6>[ 2.715248] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.722734] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.731145] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.738816] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.747416] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.756102] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.763060] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.770889] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.779913] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.787020] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.794731] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.802104] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.810229] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.817686] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 2.838148] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 2.853140] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 5.998205] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 6.007648] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 6.037716] Sending DHCP requests ., OK <6>[ 6.081805] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.35 <6>[ 6.090112] IP-Config: Complete: <6>[ 6.093613] device=eth0, hwaddr=00:19:b8:08:f1:09, ipaddr=192.168.201.35, mask=255.255.255.0, gw=192.168.201.1 <6>[ 6.104333] host=imx6q-sabrelite-lava-cbg-5, domain=lava-rack, nis-domain=(none) <6>[ 6.112448] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 6.112453] nameserver0=192.168.201.1 <6>[ 6.130507] Freeing unused kernel memory: 2048K <6>[ 6.158343] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u2 <4>[ 6.966553] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 6.975316] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 6.983576] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 6.984937] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <4>[ 6.991828] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.003485] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 <6>[ 7.013091] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.013527] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.020541] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) <6>[ 7.020895] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.022149] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.022692] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.024028] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.024072] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 7.027272] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <4>[ 7.036843] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.041676] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 7.092491] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.099602] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.107916] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.116972] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.124181] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.132401] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.139845] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.148684] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.160302] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.178968] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.187700] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.194671] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.203388] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.212450] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.219888] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.228498] sgtl5000 0-000a: Linked as a consumer to regulator.7 <6>[ 7.234831] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.242308] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.249464] sgtl5000 0-000a: Linked as a consumer to regulator.8 <6>[ 7.257539] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.265568] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 7.266121] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 7.284431] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 7.300334] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 7.313769] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 7.320188] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 7.327150] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 0 <4>[ 7.335768] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.344537] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.351732] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.360675] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.369757] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.377880] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.386127] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.393584] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.402447] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.410012] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.419266] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.427989] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.434951] panel-simple panel-lcd: Dropping the link to regulator.0 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. IP-Config: eth0 hardware address 00:19:b8:08:f1:09 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.35 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-5 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 8.497633] systemd[1]: System time before build time, advancing clock. <3>[ 8.527408] cgroup: cgroup2: unknown option "memory_recursiveprot" <30>[ 8.542596] systemd[1]: systemd 247.3-7+deb11u2 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 8.567097] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! <30>[ 8.610130] systemd[1]: Set hostname to . <30>[ 9.300769] systemd[1]: Queued start job for default target Graphical Interface. <5>[ 9.310038] random: systemd: uninitialized urandom read (16 bytes read) <28>[ 9.317099] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. <28>[ 9.329870] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) <30>[ 9.339450] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. <5>[ 9.377876] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 9.385925] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. <5>[ 9.427867] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 9.435871] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. <30>[ 9.478737] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. <30>[ 9.518070] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. <30>[ 9.558442] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. <30>[ 9.598220] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 9.610744] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. <30>[ 9.648755] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. <30>[ 9.678119] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. <30>[ 9.717943] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. <30>[ 9.748178] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. <30>[ 9.778993] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. <30>[ 9.851294] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. <30>[ 9.861074] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). <30>[ 9.899252] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. <30>[ 9.939292] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. <30>[ 9.980360] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. <30>[ 10.019127] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. <30>[ 10.058268] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 10.067271] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. <30>[ 10.079811] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... <30>[ 10.123696] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... <30>[ 10.162359] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... <30>[ 10.211322] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... <30>[ 10.250833] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... <30>[ 10.291334] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... <30>[ 10.342239] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. <5>[ 10.352481] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 10.362085] systemd[1]: Starting Journal Service... Starting Journal Service... <5>[ 10.413638] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 10.424686] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... <5>[ 10.458064] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 10.469385] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... <30>[ 10.511191] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... <30>[ 10.554003] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. <30>[ 10.588495] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. <30>[ 10.628947] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. <30>[ 10.683967] systemd[1]: modprobe@configfs.service: Succeeded. <30>[ 10.690958] systemd[1]: Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module configfs. <30>[ 10.728646] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Apply Kernel Variables... <46>[ 11.008025] systemd-journald[164]: Received client request to flush runtime journal. Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. <5>[ 11.408417] random: systemd: uninitialized urandom read (16 bytes read) Starting Create Static Device Nodes in /dev... [ OK ] Finished Coldplug All udev Devices. <5>[ 11.494571] random: systemd-journal: uninitialized urandom read (16 bytes read) <5>[ 11.506504] random: systemd-journal: uninitialized urandom read (16 bytes read) [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... <5>[ 11.947624] random: crng init done <5>[ 11.951313] random: 48 urandom warning(s) missed due to ratelimiting [ OK ] Finished Load/Save Random Seed. [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... [ OK ] Finished Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Found device /dev/ttymxc1. [ OK ] Started Network Name Resolution. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 4.19.305-cip106 #1 SMP Tue Jan 16 03:09:25 UTC 2024 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/12543572/extract-nfsrootfs-f0jtrhn8' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/12543572/extract-nfsrootfs-f0jtrhn8' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-12543572/environment . /lava-12543572/environment / # /lava-12543572/bin/lava-test-runner /lava-12543572/0 /lava-12543572/bin/lava-test-runner /lava-12543572/0 + export TESTRUN_ID=0_dmesg + cd /lava-12543572/0/tests/0_dmesg + cat uuid + UUID=12543572_1.6.2.4.1 + set +<8>[ 24.622366] x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 24.695642] <8>[ 24.754891] <8>[ 24.814082] + set +x <8>[ 24.823619] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-12543572/environment / # . /lava-12543572/environment/lava-12543572/bin/lava-test-runner /lava-12543572/1 / # /lava-12543572/bin/lava-test-runner /lava-12543572/1 + export TESTRUN_ID=1_bootrr + cd /lava-12543572/1/tests/1_bootrr + cat uuid + UUID=12543572_1.6.2.4.5 + set +<8>[ 25.363033] x + export PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-12543572/1/../bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto panel-lvds0 backlight-lcd backlight-lvds panel-lcd /lava-12543572/1/../bin/lava-test-case <8>[ 26.464200] /lava-12543572/1/../bin/lava-test-case <8>[ 26.519044] /lava-12543572/1/../bin/lava-test-case <8>[ 26.549850] + set +x <8>[ 26.573409] / #