[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.38 (4 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 13069811/tftp-deploy-48e3ze6i/kernel/zImage tftp 0x10000000 13069811/tftp-deploy-48e3ze6i/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.38 Filename '13069811/tftp-deploy-48e3ze6i/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########### 14.2 MiB/s done Bytes transferred = 8737280 (855200 hex) => tftp 0x14000000 13069811/tftp-deploy-48e3ze6i/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 13069811/tftp-deploy-48e3ze6i/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.38 Filename '13069811/tftp-deploy-48e3ze6i/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################ 5.9 MiB/s done Bytes transferred = 13336910 (cb814e hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 13069811/tftp-deploy-48e3ze6i/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 13069811/tftp-deploy-48e3ze6i/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.38 Filename '13069811/tftp-deploy-48e3ze6i/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 5 MiB/s done Bytes transferred = 41822 (a35e hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x855200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 13336846 Bytes = 12.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d35d Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.310-cip107 (KernelCI@build-j142724-arm-gcc-10-multi-v7-defconfig-nj6vt) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Sat Mar 16 07:52:52 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] percpu: Embedded 16 pages/cpu s36748 r8192 d20596 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 939136K/1048576K available (12288K kernel code, 1597K rwdata, 4688K rodata, 2048K init, 394K bss, 43904K reserved, 65536K cma-reserved, 196608K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1598 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 395 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008444] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.021335] Console: colour dummy device 80x30 <6>[ 0.023219] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.033634] CPU: Testing write buffer coherency: ok <6>[ 0.038768] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.044065] pid_max: default: 32768 minimum: 301 <6>[ 0.049064] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.055833] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.063986] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.069733] Setting up static identity map for 0x10300000 - 0x103000a0 <6>[ 0.077420] rcu: Hierarchical SRCU implementation. <6>[ 0.083975] EFI services will not be available. <6>[ 0.086233] smp: Bringing up secondary CPUs ... <6>[ 0.091488] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.091495] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.102835] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.102841] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.114024] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.114030] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.124475] smp: Brought up 1 node, 4 CPUs <6>[ 0.128738] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.135153] CPU: All CPU(s) started in SVC mode. <6>[ 0.141110] devtmpfs: initialized <6>[ 0.150687] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.156140] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.165893] futex hash table entries: 1024 (order: 4, 65536 bytes) <6>[ 0.175419] pinctrl core: initialized pinctrl subsystem <6>[ 0.179710] DMI not present or invalid. <6>[ 0.182931] NET: Registered protocol family 16 <6>[ 0.190306] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.196929] cpuidle: using governor menu <6>[ 0.198957] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.213827] vdd1p1: supplied by regulator-dummy <6>[ 0.216291] vdd3p0: supplied by regulator-dummy <6>[ 0.221022] vdd2p5: supplied by regulator-dummy <6>[ 0.225856] vddarm: supplied by regulator-dummy <6>[ 0.230771] vddpu: supplied by regulator-dummy <6>[ 0.235173] vddsoc: supplied by regulator-dummy <6>[ 0.253719] No ATAGs? <6>[ 0.253868] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.261828] hw-breakpoint: maximum watchpoint size is 4 bytes. <4>[ 0.271328] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory <6>[ 0.278209] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver <6>[ 0.290150] Serial: AMBA PL011 UART driver <6>[ 0.293961] console [pstore-1] enabled <6>[ 0.295827] pstore: Registered ramoops as persistent store backend <6>[ 0.302095] ramoops: attached 0x10000@0x30000000, ecc: 0/0 <6>[ 0.330411] mxs-dma 110000.dma-apbh: initialized <6>[ 0.339824] vgaarb: loaded <5>[ 0.340745] SCSI subsystem initialized <6>[ 0.344348] usbcore: registered new interface driver usbfs <6>[ 0.349768] usbcore: registered new interface driver hub <6>[ 0.355284] usbcore: registered new device driver usb <6>[ 0.361845] i2c i2c-0: IMX I2C adapter registered <6>[ 0.365523] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.371675] i2c i2c-1: IMX I2C adapter registered <6>[ 0.376065] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.382002] i2c i2c-2: IMX I2C adapter registered <6>[ 0.386595] i2c i2c-2: can't use DMA, using PIO instead. <6>[ 0.393683] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.397374] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.406781] PTP clock support registered <6>[ 0.411164] EDAC MC: Ver: 3.0.0 <6>[ 0.417114] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.480898] NET: Registered protocol family 2 <6>[ 0.483106] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.490650] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) <6>[ 0.497611] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.504931] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) <6>[ 0.511715] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.518382] UDP hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.524374] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.531139] NET: Registered protocol family 1 <6>[ 0.536125] RPC: Registered named UNIX socket transport module. <6>[ 0.541769] RPC: Registered udp transport module. <6>[ 0.546696] RPC: Registered tcp transport module. <6>[ 0.551680] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.558870] Trying to unpack rootfs image as initramfs... <6>[ 1.677951] Freeing initrd memory: 13028K <4>[ 1.679879] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 1.687070] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 1.697089] Initialise system trusted keyrings <6>[ 1.700122] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 1.712406] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.716274] NFS: Registering the id_resolver key type <5>[ 1.721094] Key type id_resolver registered <5>[ 1.725395] Key type id_legacy registered <6>[ 1.729713] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 1.736492] Key type asymmetric registered <5>[ 1.738658] Asymmetric key parser 'x509' registered <6>[ 1.743798] bounce: pool size: 64 pages <6>[ 1.747899] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 1.755499] io scheduler noop registered <6>[ 1.759691] io scheduler deadline registered <6>[ 1.764327] io scheduler cfq registered (default) <6>[ 1.769176] io scheduler mq-deadline registered <6>[ 1.773941] io scheduler kyber registered <6>[ 1.800093] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 1.804614] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 1.811773] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 1.819063] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 1.839334] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set <6>[ 1.842725] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc <4>[ 1.850578] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set <6>[ 1.856749] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 <4>[ 1.864651] PU : no governor for states <4>[ 1.864715] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 1.868629] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc <6>[ 1.878375] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 1.940007] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 1.947287] SuperH (H)SCI(F) driver initialized <6>[ 1.950137] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX <6>[ 1.958876] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX <6>[ 1.969885] console [ttymxc1] enabled <6>[ 1.969885] console [ttymxc1] enabled <6>[ 1.974866] bootconsole [ec_imx21] disabled <6>[ 1.974866] bootconsole [ec_imx21] disabled <6>[ 1.985025] msm_serial: driver initialized <6>[ 1.991219] STMicroelectronics ASC driver initialized <6>[ 1.998402] STM32 USART driver initialized <4>[ 2.013528] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.022227] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.029213] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.035970] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.045011] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.052180] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.066727] brd: module loaded <6>[ 2.076678] loop: module loaded <6>[ 2.083294] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 2.091511] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 2.099800] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 2.108270] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <6>[ 2.119036] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 2.126292] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 2.135382] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 2.146185] scsi host0: ahci-imx <6>[ 2.150269] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 <6>[ 2.169140] CAN device driver interface <6>[ 2.174475] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 2.181597] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator <6>[ 2.190558] fec 2188000.ethernet: Linked as a consumer to regulator.0 <6>[ 2.199642] pps pps0: new PPS source ptp0 <6>[ 2.230256] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 2.237717] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 2.243818] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.250070] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 2.257312] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 2.269027] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 2.276730] usbcore: registered new interface driver pegasus <6>[ 2.282722] usbcore: registered new interface driver asix <6>[ 2.288434] usbcore: registered new interface driver ax88179_178a <6>[ 2.294827] usbcore: registered new interface driver cdc_ether <6>[ 2.300988] usbcore: registered new interface driver smsc75xx <6>[ 2.307041] usbcore: registered new interface driver smsc95xx <6>[ 2.313107] usbcore: registered new interface driver net1080 <6>[ 2.319084] usbcore: registered new interface driver cdc_subset <6>[ 2.325301] usbcore: registered new interface driver zaurus <6>[ 2.331220] usbcore: registered new interface driver cdc_ncm <6>[ 2.340029] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 2.346826] ehci-pci: EHCI PCI platform driver <6>[ 2.351597] ehci-platform: EHCI generic platform driver <6>[ 2.357395] ehci-orion: EHCI orion driver <6>[ 2.361883] SPEAr-ehci: EHCI SPEAr driver <6>[ 2.366340] ehci-st: EHCI STMicroelectronics driver <6>[ 2.371697] ehci-exynos: EHCI EXYNOS driver <6>[ 2.376323] ehci-atmel: EHCI Atmel driver <6>[ 2.380809] tegra-ehci: Tegra EHCI driver <6>[ 2.385297] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 2.391778] ohci-pci: OHCI PCI platform driver <6>[ 2.396527] ohci-platform: OHCI generic platform driver <6>[ 2.402300] SPEAr-ohci: OHCI SPEAr driver <6>[ 2.406767] ohci-st: OHCI STMicroelectronics driver <6>[ 2.412112] ohci-atmel: OHCI Atmel driver <6>[ 2.417392] usbcore: registered new interface driver usb-storage <6>[ 2.425927] imx_usb 2184000.usb: Linked as a consumer to regulator.9 <6>[ 2.438096] imx_usb 2184200.usb: Linked as a consumer to regulator.14 <6>[ 2.448219] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 2.453388] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 2.487142] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 2.488577] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 2.493466] hub 1-0:1.0: USB hub found <6>[ 2.498532] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 2.502550] hub 1-0:1.0: 1 port detected <6>[ 2.509065] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 2.519390] i2c /dev entries driver <6>[ 2.538732] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) <6>[ 2.550032] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.556478] sdhci: Copyright(c) Pierre Ossman <6>[ 2.563361] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.571580] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.578380] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO <6>[ 2.583813] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO <6>[ 2.589333] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.627331] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA <6>[ 2.635333] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO <6>[ 2.640867] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.680781] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA <6>[ 2.692129] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 2.699406] usbcore: registered new interface driver usbhid <6>[ 2.705245] usbhid: USB HID core driver <6>[ 2.715188] NET: Registered protocol family 10 <6>[ 2.721102] Segment Routing with IPv6 <6>[ 2.725111] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.730117] mmc0: new high speed SDHC card at address 0001 <6>[ 2.731866] NET: Registered protocol family 17 <6>[ 2.738758] mmcblk0: mmc0:0001 SD 14.6 GiB <6>[ 2.741829] can: controller area network core (rev 20170425 abi 9) <6>[ 2.752778] NET: Registered protocol family 29 <6>[ 2.757516] can: raw protocol (rev 20170425) <4>[ 2.758179] GPT:Primary header thinks Alt. header is not at the end of the disk. <6>[ 2.762058] can: broadcast manager protocol (rev 20170425 t) <4>[ 2.769745] GPT:7812499 != 30560255 <6>[ 2.775655] can: netlink gateway (rev 20170425) max_hops=1 <4>[ 2.779417] GPT:Alternate GPT header not at the end of the disk. <5>[ 2.785603] Key type dns_resolver registered <4>[ 2.791453] GPT:7812499 != 30560255 <4>[ 2.799757] GPT: Use GNU Parted to correct GPT errors. <6>[ 2.800649] cpu cpu0: Linked as a consumer to regulator.4 <6>[ 2.805206] mmcblk0: p1 p2 p3 <6>[ 2.810910] cpu cpu0: Linked as a consumer to regulator.5 <6>[ 2.814287] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 2.819899] cpu cpu0: Linked as a consumer to regulator.6 <6>[ 2.833163] ThumbEE CPU extension supported. <5>[ 2.837771] Registering SWP/SWPB emulation handler <5>[ 2.843314] Loading compiled-in X.509 certificates <6>[ 2.849830] pstore: Using compression: deflate <6>[ 2.867699] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.875082] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.883669] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.891140] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.899747] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.908431] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.915370] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.923222] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.932243] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.939363] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.947884] imx_thermal tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <6>[ 2.958374] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.965752] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.974021] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.981525] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.990064] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.998742] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.005674] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.013466] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.022485] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.029608] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.037379] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.044755] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.052983] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.060467] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 3.067766] hub 1-1:1.0: USB hub found <4>[ 3.069049] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.080462] hub 1-1:1.0: 3 ports detected <6>[ 3.080496] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.091696] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.099623] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.108655] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.115780] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.123500] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.130876] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.139010] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.146446] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.154932] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.163604] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.170546] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 3.178768] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 3.185639] hctosys: unable to open rtc device (rtc0) <4>[ 3.192409] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.201516] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.208670] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.216532] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.223944] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.232253] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.239732] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.248313] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.256971] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.263924] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 3.317784] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 3.332752] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 6.477722] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 6.487198] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 6.517239] Sending DHCP requests ., OK <6>[ 6.561352] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.38 <6>[ 6.569699] IP-Config: Complete: <6>[ 6.573218] device=eth0, hwaddr=00:19:b8:08:f0:fe, ipaddr=192.168.201.38, mask=255.255.255.0, gw=192.168.201.1 <6>[ 6.583964] host=imx6q-sabrelite-lava-cbg-8, domain=lava-rack, nis-domain=(none) <6>[ 6.592104] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 6.592112] nameserver0=192.168.201.1 <6>[ 6.611005] Freeing unused kernel memory: 2048K <6>[ 6.627501] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 6.743304] udevd[108]: starting version 3.2.9 <5>[ 6.748962] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.755868] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.762802] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 6.776456] udevd[108]: specified user 'tss' unknown <27>[ 6.781995] udevd[108]: specified group 'tss' unknown <30>[ 6.789424] udevd[109]: starting eudev-3.2.9 <4>[ 7.127466] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.136514] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.149078] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 <6>[ 7.154260] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.156739] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) <6>[ 7.171665] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.179892] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.188005] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.196739] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.202485] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.208631] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.220276] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.223677] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.229010] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.235776] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 7.242786] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.257500] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.266556] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.273831] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.299309] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.306733] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.314641] sgtl5000 0-000a: Linked as a consumer to regulator.7 <6>[ 7.321343] sgtl5000 0-000a: Linked as a consumer to regulator.8 <6>[ 7.327886] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.335424] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 7.335676] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 7.340980] sgtl5000 0-000a: sgtl5000 revision 0x11 <4>[ 7.344919] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.362808] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.369864] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.379430] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.383606] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 7.388539] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.394842] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 7.402000] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.415612] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 0 <6>[ 7.417290] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 7.423888] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.438516] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.447364] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.454875] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.464376] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.473142] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.480399] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.489018] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.498102] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.505246] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.514129] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.521561] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.530567] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.538064] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.547297] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.556048] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.563114] panel-simple panel-lcd: Dropping the link to regulator.0 done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 7.790425] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-13069811/environment . /lava-13069811/environment / # /lava-13069811/bin/lava-test-runner /lava-13069811/0 /lava-13069811/bin/lava-test-runner /lava-13069811/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-13069811/0/tests/0_dmesg + cat uuid + UUID=13069811<8>[ 8.397056] _1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 8.442395] <8>[ 8.482327] <8>[ 8.522694] + set +x <8>[ 8.532539] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-13069811/environment / # . /lava-13069811/environment/lava-13069811/bin/lava-test-runner /lava-13069811/1 / # /lava-13069811/bin/lava-test-runner /lava-13069811/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-13069811/1/tests/1_bootrr + cat uuid + UUID=1306981<8>[ 9.033730] 1_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-13069811/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto panel-lvds0 backlight-lcd backlight-lvds panel-lcd /lava-13069811/1/../bin/lava-test-case <8>[ 10.115389] /lava-13069811/1/../bin/lava-test-case <8>[ 10.154662] /lava-13069811/1/../bin/lava-test-case <8>[ 10.179313] + set +x <8>[ 10.198021] / #