[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.0 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected sst25vf016b with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 6 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.12 (7 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 13069806/tftp-deploy-oa8jiqxy/kernel/zImage tftp 0x10000000 13069806/tftp-deploy-oa8jiqxy/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.12 Filename '13069806/tftp-deploy-oa8jiqxy/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########### 4.2 MiB/s done Bytes transferred = 8737280 (855200 hex) => tftp 0x14000000 13069806/tftp-deploy-oa8jiqxy/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 13069806/tftp-deploy-oa8jiqxy/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.12 Filename '13069806/tftp-deploy-oa8jiqxy/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################### 4.2 MiB/s done Bytes transferred = 9415811 (8fac83 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 13069806/tftp-deploy-oa8jiqxy/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 13069806/tftp-deploy-oa8jiqxy/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.12 Filename '13069806/tftp-deploy-oa8jiqxy/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 2.1 MiB/s done Bytes transferred = 41822 (a35e hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/13069806/extract-nfsrootfs-d5fvn7dp,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/13069806/extract-nfsrootfs-d5fvn7dp,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x855200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 9415747 Bytes = 9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d35d Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.310-cip107 (KernelCI@build-j142724-arm-gcc-10-multi-v7-defconfig-nj6vt) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Sat Mar 16 07:52:52 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] percpu: Embedded 16 pages/cpu s36748 r8192 d20596 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/13069806/extract-nfsrootfs-d5fvn7dp,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 942968K/1048576K available (12288K kernel code, 1597K rwdata, 4688K rodata, 2048K init, 394K bss, 40072K reserved, 65536K cma-reserved, 196608K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1598 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 395 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 15ns <6>[ 0.000006] sched_clock: 32 bits at 66MHz, resolution 15ns, wraps every 32537631224ns <6>[ 0.008094] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 28958491609 ns <6>[ 0.020907] Console: colour dummy device 80x30 <6>[ 0.022790] Calibrating delay loop (skipped), value calculated using timer frequency.. 132.00 BogoMIPS (lpj=660000) <6>[ 0.033467] CPU: Testing write buffer coherency: ok <6>[ 0.038601] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.043897] pid_max: default: 32768 minimum: 301 <6>[ 0.048897] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.055653] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.063836] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.069563] Setting up static identity map for 0x10300000 - 0x103000a0 <6>[ 0.077270] rcu: Hierarchical SRCU implementation. <6>[ 0.083811] EFI services will not be available. <6>[ 0.086065] smp: Bringing up secondary CPUs ... <6>[ 0.091322] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.091330] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.102673] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.102679] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.113858] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.113864] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.124316] smp: Brought up 1 node, 4 CPUs <6>[ 0.128574] SMP: Total of 4 processors activated (528.00 BogoMIPS). <6>[ 0.135077] CPU: All CPU(s) started in SVC mode. <6>[ 0.141035] devtmpfs: initialized <6>[ 0.150642] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.156095] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.165829] futex hash table entries: 1024 (order: 4, 65536 bytes) <6>[ 0.175382] pinctrl core: initialized pinctrl subsystem <6>[ 0.179659] DMI not present or invalid. <6>[ 0.182895] NET: Registered protocol family 16 <6>[ 0.190208] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.196820] cpuidle: using governor menu <6>[ 0.198874] CPU identified as i.MX6Q, silicon rev 1.0 <6>[ 0.213732] vdd1p1: supplied by regulator-dummy <6>[ 0.216201] vdd3p0: supplied by regulator-dummy <6>[ 0.220923] vdd2p5: supplied by regulator-dummy <6>[ 0.225739] vddarm: supplied by regulator-dummy <6>[ 0.230692] vddpu: supplied by regulator-dummy <6>[ 0.235085] vddsoc: supplied by regulator-dummy <6>[ 0.253626] No ATAGs? <6>[ 0.253780] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.261739] hw-breakpoint: maximum watchpoint size is 4 bytes. <4>[ 0.271233] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory <6>[ 0.278115] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver <6>[ 0.290050] Serial: AMBA PL011 UART driver <6>[ 0.293855] console [pstore-1] enabled <6>[ 0.295725] pstore: Registered ramoops as persistent store backend <6>[ 0.302017] ramoops: attached 0x10000@0x30000000, ecc: 0/0 <6>[ 0.330297] mxs-dma 110000.dma-apbh: initialized <6>[ 0.339735] vgaarb: loaded <5>[ 0.340641] SCSI subsystem initialized <6>[ 0.344264] usbcore: registered new interface driver usbfs <6>[ 0.349678] usbcore: registered new interface driver hub <6>[ 0.355194] usbcore: registered new device driver usb <6>[ 0.361759] i2c i2c-0: IMX I2C adapter registered <6>[ 0.365433] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.371578] i2c i2c-1: IMX I2C adapter registered <6>[ 0.375978] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.381915] i2c i2c-2: IMX I2C adapter registered <6>[ 0.386507] i2c i2c-2: can't use DMA, using PIO instead. <6>[ 0.393609] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.397286] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.406694] PTP clock support registered <6>[ 0.411073] EDAC MC: Ver: 3.0.0 <6>[ 0.417061] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.481109] NET: Registered protocol family 2 <6>[ 0.483310] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.490856] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) <6>[ 0.497826] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.505139] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) <6>[ 0.511915] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.518604] UDP hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.524589] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.531352] NET: Registered protocol family 1 <6>[ 0.536334] RPC: Registered named UNIX socket transport module. <6>[ 0.541981] RPC: Registered udp transport module. <6>[ 0.546909] RPC: Registered tcp transport module. <6>[ 0.551886] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.559083] Trying to unpack rootfs image as initramfs... <6>[ 1.284700] Freeing initrd memory: 9196K <4>[ 1.286571] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 1.293895] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 1.303752] Initialise system trusted keyrings <6>[ 1.306783] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 1.319080] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.322947] NFS: Registering the id_resolver key type <5>[ 1.327701] Key type id_resolver registered <5>[ 1.332067] Key type id_legacy registered <6>[ 1.336369] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 1.343184] Key type asymmetric registered <5>[ 1.345294] Asymmetric key parser 'x509' registered <6>[ 1.350491] bounce: pool size: 64 pages <6>[ 1.354556] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 1.362198] io scheduler noop registered <6>[ 1.366347] io scheduler deadline registered <6>[ 1.371021] io scheduler cfq registered (default) <6>[ 1.375830] io scheduler mq-deadline registered <6>[ 1.380632] io scheduler kyber registered <6>[ 1.406700] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 1.411247] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 1.418387] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 1.425646] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 1.445778] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set <6>[ 1.449245] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc <4>[ 1.456992] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set <6>[ 1.463210] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 <4>[ 1.471175] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <4>[ 1.477082] PU : no governor for states <6>[ 1.480715] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 1.484792] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc <6>[ 1.558873] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 1.566182] SuperH (H)SCI(F) driver initialized <6>[ 1.569069] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX <6>[ 1.577785] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX <6>[ 1.588782] console [ttymxc1] enabled <6>[ 1.588782] console [ttymxc1] enabled <6>[ 1.593764] bootconsole [ec_imx21] disabled <6>[ 1.593764] bootconsole [ec_imx21] disabled <6>[ 1.603862] msm_serial: driver initialized <6>[ 1.610117] STMicroelectronics ASC driver initialized <6>[ 1.617290] STM32 USART driver initialized <4>[ 1.632464] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 1.641176] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 1.648157] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 1.654908] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 1.663945] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 1.671122] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 1.685710] brd: module loaded <6>[ 1.695590] loop: module loaded <6>[ 1.702195] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 1.710413] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 1.718700] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 1.727171] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <6>[ 1.737155] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 1.744410] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 1.753503] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 1.764287] scsi host0: ahci-imx <6>[ 1.768374] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 <6>[ 1.787354] CAN device driver interface <6>[ 1.792708] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 1.799793] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator <6>[ 1.808752] fec 2188000.ethernet: Linked as a consumer to regulator.0 <6>[ 1.817828] pps pps0: new PPS source ptp0 <6>[ 1.839599] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 1.846986] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 1.853119] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 1.859378] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 1.866606] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.878324] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 1.886027] usbcore: registered new interface driver pegasus <6>[ 1.892008] usbcore: registered new interface driver asix <6>[ 1.897724] usbcore: registered new interface driver ax88179_178a <6>[ 1.904117] usbcore: registered new interface driver cdc_ether <6>[ 1.910283] usbcore: registered new interface driver smsc75xx <6>[ 1.916339] usbcore: registered new interface driver smsc95xx <6>[ 1.922399] usbcore: registered new interface driver net1080 <6>[ 1.928371] usbcore: registered new interface driver cdc_subset <6>[ 1.934587] usbcore: registered new interface driver zaurus <6>[ 1.940507] usbcore: registered new interface driver cdc_ncm <6>[ 1.949353] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 1.956150] ehci-pci: EHCI PCI platform driver <6>[ 1.960919] ehci-platform: EHCI generic platform driver <6>[ 1.966697] ehci-orion: EHCI orion driver <6>[ 1.971216] SPEAr-ehci: EHCI SPEAr driver <6>[ 1.975679] ehci-st: EHCI STMicroelectronics driver <6>[ 1.981030] ehci-exynos: EHCI EXYNOS driver <6>[ 1.985667] ehci-atmel: EHCI Atmel driver <6>[ 1.990145] tegra-ehci: Tegra EHCI driver <6>[ 1.994639] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 2.001133] ohci-pci: OHCI PCI platform driver <6>[ 2.005886] ohci-platform: OHCI generic platform driver <6>[ 2.011654] SPEAr-ohci: OHCI SPEAr driver <6>[ 2.016116] ohci-st: OHCI STMicroelectronics driver <6>[ 2.021474] ohci-atmel: OHCI Atmel driver <6>[ 2.026734] usbcore: registered new interface driver usb-storage <6>[ 2.035270] imx_usb 2184000.usb: Linked as a consumer to regulator.9 <6>[ 2.047444] imx_usb 2184200.usb: Linked as a consumer to regulator.14 <6>[ 2.057569] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 2.062738] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 2.097089] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 2.103426] hub 1-0:1.0: USB hub found <6>[ 2.107510] hub 1-0:1.0: 1 port detected <6>[ 2.108607] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 2.117431] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 2.117902] i2c /dev entries driver <6>[ 2.123971] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <3>[ 2.138902] imx_thermal tempmon: invalid sensor calibration data <3>[ 2.145183] imx_thermal tempmon: failed to init from from fsl,tempmon-data <4>[ 2.152361] imx_thermal: probe of tempmon failed with error -22 <6>[ 2.161758] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) <6>[ 2.173051] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.179528] sdhci: Copyright(c) Pierre Ossman <6>[ 2.186402] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.194644] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.201454] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO <6>[ 2.206890] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO <6>[ 2.212401] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.252255] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA <6>[ 2.260302] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO <6>[ 2.265806] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.305688] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA <6>[ 2.317104] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 2.324333] usbcore: registered new interface driver usbhid <6>[ 2.330200] usbhid: USB HID core driver <6>[ 2.340163] NET: Registered protocol family 10 <6>[ 2.345974] Segment Routing with IPv6 <6>[ 2.350031] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.356763] NET: Registered protocol family 17 <6>[ 2.361519] can: controller area network core (rev 20170425 abi 9) <6>[ 2.368048] NET: Registered protocol family 29 <6>[ 2.372764] can: raw protocol (rev 20170425) <6>[ 2.377324] can: broadcast manager protocol (rev 20170425 t) <6>[ 2.383258] can: netlink gateway (rev 20170425) max_hops=1 <5>[ 2.389416] Key type dns_resolver registered <6>[ 2.394759] cpu cpu0: Linked as a consumer to regulator.4 <6>[ 2.400516] cpu cpu0: Linked as a consumer to regulator.5 <6>[ 2.406239] cpu cpu0: Linked as a consumer to regulator.6 <6>[ 2.412713] ThumbEE CPU extension supported. <5>[ 2.417295] Registering SWP/SWPB emulation handler <5>[ 2.423105] Loading compiled-in X.509 certificates <6>[ 2.429787] pstore: Using compression: deflate <6>[ 2.453277] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.460738] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.469534] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.478012] mmc0: new high speed SDHC card at address 0001 <6>[ 2.484008] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.493032] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.501734] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.510092] mmcblk0: mmc0:0001 SD 14.8 GiB <6>[ 2.514821] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 2.522013] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.530485] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.539538] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.546826] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.555145] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.562684] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.571228] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.578825] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.587759] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.596429] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.603623] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.611759] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.620819] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.628218] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.637159] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 2.644140] hctosys: unable to open rtc device (rtc0) <6>[ 2.650974] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.658641] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.667355] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <4>[ 2.674933] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 2.682641] GPT:29296874 != 30965759 <4>[ 2.686482] GPT:Alternate GPT header not at the end of the disk. <4>[ 2.692774] GPT:29296874 != 30965759 <4>[ 2.696614] GPT: Use GNU Parted to correct GPT errors. <6>[ 2.702077] mmcblk0: p1 p2 p3 <6>[ 2.705611] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.714592] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.723299] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.730301] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.738416] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.747463] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.754706] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.764642] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.767701] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:06: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:06, irq=POLL) <6>[ 2.774165] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.786811] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 2.795203] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.807534] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.816440] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.825138] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.832258] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.840395] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.849449] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.856709] hub 1-1:1.0: USB hub found <6>[ 2.860828] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.868208] hub 1-1:1.0: 3 ports detected <6>[ 2.874189] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.881580] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.890018] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.897517] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.906304] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.914999] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.921962] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.930013] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.939051] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.946171] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 4.877708] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 4.897181] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 4.927255] Sending DHCP requests ., OK <6>[ 4.971300] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.12 <6>[ 4.979630] IP-Config: Complete: <6>[ 4.983147] device=eth0, hwaddr=0e:cc:7b:b0:7c:c7, ipaddr=192.168.201.12, mask=255.255.255.0, gw=192.168.201.1 <6>[ 4.993873] host=imx6q-sabrelite-lava-cbg-1, domain=lava-rack, nis-domain=(none) <6>[ 5.001990] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 5.001995] nameserver0=192.168.201.1 <6>[ 5.019651] Freeing unused kernel memory: 2048K <6>[ 5.067730] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u4 <6>[ 6.061131] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 6.068657] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 6.077708] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 6.085293] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 6.094649] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 6.096597] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 <6>[ 6.103526] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 6.111088] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) <6>[ 6.117296] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 6.132127] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 6.139096] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 6.147728] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 6.156768] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 6.158651] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 6.163959] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 6.170713] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 6.178898] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 6.191270] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 6.200217] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 6.207730] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 6.217356] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 6.226096] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 6.233217] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 6.253906] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 6.255793] sgtl5000 0-000a: Linked as a consumer to regulator.7 <6>[ 6.269378] sgtl5000 0-000a: Linked as a consumer to regulator.8 <6>[ 6.276531] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 6.277724] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 6.285400] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 6.297598] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 6.305815] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 6.314922] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 6.321030] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 6.323008] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 6.339779] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 6.348514] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 6.356040] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 6.368047] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <4>[ 6.381977] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 6.391152] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 6.403330] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 6.410138] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 6.410151] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 6.424894] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 6.425484] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 0 <6>[ 6.432510] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 6.448740] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 6.456279] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 6.465980] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 6.474730] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 6.481772] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 6.490702] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 6.499793] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 6.506996] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 6.515848] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 6.523277] pwm-backlight backlight-lcd: Dropping the link to regulator.8 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. IP-Config: eth0 hardware address 0e:cc:7b:b0:7c:c7 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.12 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-1 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 8.148373] systemd[1]: System time before build time, advancing clock. <3>[ 8.213915] cgroup: cgroup2: unknown option "memory_recursiveprot" <30>[ 8.238833] systemd[1]: systemd 247.3-7+deb11u4 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 8.262931] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! <30>[ 8.309818] systemd[1]: Set hostname to . <30>[ 9.262420] systemd[1]: Queued start job for default target Graphical Interface. <5>[ 9.271626] random: systemd: uninitialized urandom read (16 bytes read) <28>[ 9.278763] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. <28>[ 9.291504] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) <30>[ 9.301240] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. <5>[ 9.337459] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 9.345441] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. <5>[ 9.387433] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 9.395383] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. <30>[ 9.438256] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. <30>[ 9.477972] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. <30>[ 9.517973] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. <30>[ 9.557837] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 9.570373] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. <30>[ 9.608063] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. <30>[ 9.637661] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. <30>[ 9.677541] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. <30>[ 9.707744] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. <30>[ 9.738369] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. <30>[ 9.823392] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. <30>[ 9.833873] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). <30>[ 9.868735] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. <30>[ 9.909565] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. <30>[ 9.950865] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. <30>[ 9.988653] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. <30>[ 10.028391] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 10.037956] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. <30>[ 10.050646] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... <30>[ 10.090902] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... <30>[ 10.236621] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... <5>[ 10.277809] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 10.287995] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... <5>[ 10.328195] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 10.340066] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... <5>[ 10.377689] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 10.389143] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... <30>[ 10.432859] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. <30>[ 10.448860] systemd[1]: Starting Journal Service... Starting Journal Service... <30>[ 10.505211] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... <30>[ 10.540460] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... <30>[ 10.581091] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... <30>[ 10.623108] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. <30>[ 10.659952] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. <30>[ 10.678637] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. <30>[ 10.729748] systemd[1]: modprobe@configfs.service: Succeeded. <30>[ 10.736694] systemd[1]: Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module configfs. <30>[ 10.779067] systemd[1]: modprobe@drm.service: Succeeded. <30>[ 10.785568] systemd[1]: Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module drm. <30>[ 10.819103] systemd[1]: modprobe@fuse.service: Succeeded. <30>[ 10.825759] systemd[1]: Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Module fuse. <30>[ 10.868035] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/S<5>[ 11.057124] random: crng init done ave Random Seed... <5>[ 11.062234] random: 37 urandom warning(s) missed due to ratelimiting Starting Apply Kernel Variables... <46>[ 11.112019] systemd-journald[162]: Received client request to flush runtime journal. Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Coldplug All udev Devices. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... [ OK ] Finished Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Found device /dev/ttymxc1. [ OK ] Started Network Name Resolution. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 4.19.310-cip107 #1 SMP Sat Mar 16 07:52:52 UTC 2024 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/13069806/extract-nfsrootfs-d5fvn7dp' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/13069806/extract-nfsrootfs-d5fvn7dp' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-13069806/environment . /lava-13069806/environment / # /lava-13069806/bin/lava-test-runner /lava-13069806/0 /lava-13069806/bin/lava-test-runner /lava-13069806/0 + export TESTRUN_ID=0_dmesg + cd /lava-13069806/0/tests/0_dmesg + cat uuid + UUID=13069806_1.6.2.4.1 + <8>[ 28.472632] set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 28.608097] <8>[ 28.708462] <8>[ 28.816638] + set +x <8>[ 28.826175] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-13069806/environment / # . /lava-13069806/environment/lava-13069806/bin/lava-test-runner /lava-13069806/1 / # /lava-13069806/bin/lava-test-runner /lava-13069806/1 + export TESTRUN_ID=1_bootrr + cd /lava-13069806/1/tests/1_bootrr + cat uuid + UUID=13069806_1.6.2.4.5 + <8>[ 29.457263] set +x + export PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-13069806/1/../bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto backlight-lvds panel-lcd panel-lvds0 backlight-lcd /lava-13069806/1/../bin/lava-test-case <8>[ 30.654341] /lava-13069806/1/../bin/lava-test-case <8>[ 30.764425] /lava-13069806/1/../bin/lava-test-case <8>[ 30.825326] + set +x <8>[ 30.865085] / #