[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.37 (7 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 13238344/tftp-deploy-lt4xdkel/kernel/zImage tftp 0x10000000 13238344/tftp-deploy-lt4xdkel/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '13238344/tftp-deploy-lt4xdkel/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########### 14.3 MiB/s done Bytes transferred = 8737280 (855200 hex) => tftp 0x14000000 13238344/tftp-deploy-lt4xdkel/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 13238344/tftp-deploy-lt4xdkel/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '13238344/tftp-deploy-lt4xdkel/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################ 14.4 MiB/s done Bytes transferred = 13334966 (cb79b6 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 13238344/tftp-deploy-lt4xdkel/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 13238344/tftp-deploy-lt4xdkel/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '13238344/tftp-deploy-lt4xdkel/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 5.7 MiB/s done Bytes transferred = 41822 (a35e hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x855200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 13334902 Bytes = 12.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d35d Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.311-cip108 (KernelCI@build-j153949-arm-gcc-10-multi-v7-defconfig-2qm2z) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Wed Apr 3 08:23:13 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] percpu: Embedded 16 pages/cpu s36748 r8192 d20596 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 939140K/1048576K available (12288K kernel code, 1598K rwdata, 4688K rodata, 2048K init, 394K bss, 43900K reserved, 65536K cma-reserved, 196608K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1599 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 395 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000006] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008444] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.021392] Console: colour dummy device 80x30 <6>[ 0.023272] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.033690] CPU: Testing write buffer coherency: ok <6>[ 0.038823] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.044121] pid_max: default: 32768 minimum: 301 <6>[ 0.049126] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.055890] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.064048] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.069791] Setting up static identity map for 0x10300000 - 0x103000a0 <6>[ 0.077517] rcu: Hierarchical SRCU implementation. <6>[ 0.084080] EFI services will not be available. <6>[ 0.086323] smp: Bringing up secondary CPUs ... <6>[ 0.091600] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.091606] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.102938] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.102945] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.114126] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.114132] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.124584] smp: Brought up 1 node, 4 CPUs <6>[ 0.128840] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.135258] CPU: All CPU(s) started in SVC mode. <6>[ 0.141215] devtmpfs: initialized <6>[ 0.150847] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.156301] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.166051] futex hash table entries: 1024 (order: 4, 65536 bytes) <6>[ 0.175583] pinctrl core: initialized pinctrl subsystem <6>[ 0.179881] DMI not present or invalid. <6>[ 0.183104] NET: Registered protocol family 16 <6>[ 0.190450] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.197100] cpuidle: using governor menu <6>[ 0.199095] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.214100] vdd1p1: supplied by regulator-dummy <6>[ 0.216575] vdd3p0: supplied by regulator-dummy <6>[ 0.221294] vdd2p5: supplied by regulator-dummy <6>[ 0.226131] vddarm: supplied by regulator-dummy <6>[ 0.231044] vddpu: supplied by regulator-dummy <6>[ 0.235453] vddsoc: supplied by regulator-dummy <6>[ 0.254193] No ATAGs? <6>[ 0.254336] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.262297] hw-breakpoint: maximum watchpoint size is 4 bytes. <4>[ 0.271864] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory <6>[ 0.278746] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver <6>[ 0.290760] Serial: AMBA PL011 UART driver <6>[ 0.294635] console [pstore-1] enabled <6>[ 0.296456] pstore: Registered ramoops as persistent store backend <6>[ 0.302705] ramoops: attached 0x10000@0x30000000, ecc: 0/0 <6>[ 0.331259] mxs-dma 110000.dma-apbh: initialized <6>[ 0.340860] vgaarb: loaded <5>[ 0.341786] SCSI subsystem initialized <6>[ 0.345379] usbcore: registered new interface driver usbfs <6>[ 0.350835] usbcore: registered new interface driver hub <6>[ 0.356337] usbcore: registered new device driver usb <6>[ 0.362842] i2c i2c-0: IMX I2C adapter registered <6>[ 0.366580] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.372686] i2c i2c-1: IMX I2C adapter registered <6>[ 0.377102] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.383038] i2c i2c-2: IMX I2C adapter registered <6>[ 0.387633] i2c i2c-2: can't use DMA, using PIO instead. <6>[ 0.394759] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.398409] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.407818] PTP clock support registered <6>[ 0.412200] EDAC MC: Ver: 3.0.0 <6>[ 0.418213] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.482444] NET: Registered protocol family 2 <6>[ 0.484658] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.492188] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) <6>[ 0.499158] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.506477] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) <6>[ 0.513266] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.519935] UDP hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.525921] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.532685] NET: Registered protocol family 1 <6>[ 0.537660] RPC: Registered named UNIX socket transport module. <6>[ 0.543317] RPC: Registered udp transport module. <6>[ 0.548263] RPC: Registered tcp transport module. <6>[ 0.553203] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.560407] Trying to unpack rootfs image as initramfs... <6>[ 1.674436] Freeing initrd memory: 13024K <4>[ 1.676384] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 1.683632] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 1.693587] Initialise system trusted keyrings <6>[ 1.696680] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 1.708997] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.712872] NFS: Registering the id_resolver key type <5>[ 1.717577] Key type id_resolver registered <5>[ 1.722008] Key type id_legacy registered <6>[ 1.726289] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 1.733065] Key type asymmetric registered <5>[ 1.735211] Asymmetric key parser 'x509' registered <6>[ 1.740417] bounce: pool size: 64 pages <6>[ 1.744474] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 1.752108] io scheduler noop registered <6>[ 1.756264] io scheduler deadline registered <6>[ 1.760937] io scheduler cfq registered (default) <6>[ 1.765748] io scheduler mq-deadline registered <6>[ 1.770547] io scheduler kyber registered <6>[ 1.797115] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 1.801658] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 1.808801] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 1.816066] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 1.836444] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set <6>[ 1.839869] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc <4>[ 1.847653] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set <6>[ 1.853879] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 <4>[ 1.861821] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <4>[ 1.868235] PU : no governor for states <6>[ 1.871386] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 1.875456] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc <6>[ 1.945371] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 1.952705] SuperH (H)SCI(F) driver initialized <6>[ 1.955556] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX <6>[ 1.964318] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX <6>[ 1.975283] console [ttymxc1] enabled <6>[ 1.975283] console [ttymxc1] enabled <6>[ 1.980284] bootconsole [ec_imx21] disabled <6>[ 1.980284] bootconsole [ec_imx21] disabled <6>[ 1.990461] msm_serial: driver initialized <6>[ 1.996592] STMicroelectronics ASC driver initialized <6>[ 2.003795] STM32 USART driver initialized <4>[ 2.019137] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.027811] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.034794] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.041584] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.050635] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.057754] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.072437] brd: module loaded <6>[ 2.082387] loop: module loaded <6>[ 2.089113] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 2.097307] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 2.105607] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 2.114068] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <6>[ 2.124863] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 2.132146] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 2.141222] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 2.152068] scsi host0: ahci-imx <6>[ 2.156135] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 <6>[ 2.175241] CAN device driver interface <6>[ 2.180649] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 2.187723] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator <6>[ 2.196704] fec 2188000.ethernet: Linked as a consumer to regulator.0 <6>[ 2.205787] pps pps0: new PPS source ptp0 <6>[ 2.236528] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 2.243971] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 2.250100] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.256340] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 2.263588] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 2.275371] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 2.283101] usbcore: registered new interface driver pegasus <6>[ 2.289091] usbcore: registered new interface driver asix <6>[ 2.294791] usbcore: registered new interface driver ax88179_178a <6>[ 2.301201] usbcore: registered new interface driver cdc_ether <6>[ 2.307351] usbcore: registered new interface driver smsc75xx <6>[ 2.313427] usbcore: registered new interface driver smsc95xx <6>[ 2.319488] usbcore: registered new interface driver net1080 <6>[ 2.325445] usbcore: registered new interface driver cdc_subset <6>[ 2.331678] usbcore: registered new interface driver zaurus <6>[ 2.337584] usbcore: registered new interface driver cdc_ncm <6>[ 2.346482] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 2.353313] ehci-pci: EHCI PCI platform driver <6>[ 2.358063] ehci-platform: EHCI generic platform driver <6>[ 2.363893] ehci-orion: EHCI orion driver <6>[ 2.368418] SPEAr-ehci: EHCI SPEAr driver <6>[ 2.372887] ehci-st: EHCI STMicroelectronics driver <6>[ 2.378242] ehci-exynos: EHCI EXYNOS driver <6>[ 2.382889] ehci-atmel: EHCI Atmel driver <6>[ 2.387352] tegra-ehci: Tegra EHCI driver <6>[ 2.391871] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 2.398371] ohci-pci: OHCI PCI platform driver <6>[ 2.403127] ohci-platform: OHCI generic platform driver <6>[ 2.408929] SPEAr-ohci: OHCI SPEAr driver <6>[ 2.413398] ohci-st: OHCI STMicroelectronics driver <6>[ 2.418759] ohci-atmel: OHCI Atmel driver <6>[ 2.424044] usbcore: registered new interface driver usb-storage <6>[ 2.432623] imx_usb 2184000.usb: Linked as a consumer to regulator.9 <6>[ 2.444802] imx_usb 2184200.usb: Linked as a consumer to regulator.14 <6>[ 2.454962] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 2.460151] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 2.488238] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 2.489803] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 2.494580] hub 1-0:1.0: USB hub found <6>[ 2.499628] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 2.503647] hub 1-0:1.0: 1 port detected <6>[ 2.510157] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 2.520646] i2c /dev entries driver <6>[ 2.540077] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) <6>[ 2.551501] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.557949] sdhci: Copyright(c) Pierre Ossman <6>[ 2.564899] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.573196] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.580014] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO <6>[ 2.585448] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO <6>[ 2.590965] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.630792] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA <6>[ 2.638828] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO <6>[ 2.644333] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.684222] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA <6>[ 2.695667] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 2.702939] usbcore: registered new interface driver usbhid <6>[ 2.708804] usbhid: USB HID core driver <6>[ 2.718876] NET: Registered protocol family 10 <6>[ 2.724777] Segment Routing with IPv6 <6>[ 2.728815] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.735536] NET: Registered protocol family 17 <6>[ 2.735903] mmc0: new high speed SDHC card at address e624 <6>[ 2.740285] can: controller area network core (rev 20170425 abi 9) <6>[ 2.747715] mmcblk0: mmc0:e624 SL16G 14.8 GiB <6>[ 2.752622] NET: Registered protocol family 29 <6>[ 2.761986] can: raw protocol (rev 20170425) <4>[ 2.764762] GPT:Primary header thinks Alt. header is not at the end of the disk. <6>[ 2.766529] can: broadcast manager protocol (rev 20170425 t) <4>[ 2.774218] GPT:29296874 != 31116287 <6>[ 2.780144] can: netlink gateway (rev 20170425) max_hops=1 <4>[ 2.783978] GPT:Alternate GPT header not at the end of the disk. <5>[ 2.790191] Key type dns_resolver registered <4>[ 2.796014] GPT:29296874 != 31116287 <4>[ 2.804409] GPT: Use GNU Parted to correct GPT errors. <6>[ 2.805353] cpu cpu0: Linked as a consumer to regulator.4 <6>[ 2.809886] mmcblk0: p1 p2 p3 <6>[ 2.815555] cpu cpu0: Linked as a consumer to regulator.5 <6>[ 2.818966] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 2.824550] cpu cpu0: Linked as a consumer to regulator.6 <6>[ 2.837777] ThumbEE CPU extension supported. <5>[ 2.842428] Registering SWP/SWPB emulation handler <5>[ 2.847956] Loading compiled-in X.509 certificates <6>[ 2.854512] pstore: Using compression: deflate <6>[ 2.872402] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.879827] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.888417] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.895862] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.904505] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.913185] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.920140] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.927985] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.937014] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.944133] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.952668] imx_thermal tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <6>[ 2.963154] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.970537] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.978851] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.986293] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.994896] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.003571] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.010521] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.018328] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.027330] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.034465] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.041542] hub 1-1:1.0: USB hub found <6>[ 3.042291] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.045684] hub 1-1:1.0: 3 ports detected <6>[ 3.052952] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.065434] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.072902] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.081468] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.090149] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.097087] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.104879] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.113901] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.121020] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.128739] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.136091] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.144960] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 3.151877] hctosys: unable to open rtc device (rtc0) <6>[ 3.158467] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.165939] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.174741] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.183430] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.190385] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.198309] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.207318] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.214445] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.222208] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.229585] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.279168] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 3.294128] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 6.398904] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 6.418249] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 6.448300] Sending DHCP requests ., OK <6>[ 6.492451] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.37 <6>[ 6.500798] IP-Config: Complete: <6>[ 6.504319] device=eth0, hwaddr=00:19:b8:08:f0:fd, ipaddr=192.168.201.37, mask=255.255.255.0, gw=192.168.201.1 <6>[ 6.515066] host=imx6q-sabrelite-lava-cbg-7, domain=lava-rack, nis-domain=(none) <6>[ 6.523204] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 6.523214] nameserver0=192.168.201.1 <6>[ 6.542169] Freeing unused kernel memory: 2048K <6>[ 6.558630] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 6.676561] udevd[109]: starting version 3.2.9 <5>[ 6.682845] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.689934] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.696756] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 6.711189] udevd[109]: specified user 'tss' unknown <27>[ 6.716633] udevd[109]: specified group 'tss' unknown <30>[ 6.724058] udevd[110]: starting eudev-3.2.9 <6>[ 7.081958] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.090996] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 7.100354] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 <6>[ 7.108039] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) <6>[ 7.108649] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <4>[ 7.123393] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.132134] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.132596] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.139420] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.154246] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.163342] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.170976] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.173907] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.179273] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.184637] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 7.192314] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.207254] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.215065] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.224479] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.227860] sgtl5000 0-000a: Linked as a consumer to regulator.7 <6>[ 7.239504] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.246508] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 7.253733] sgtl5000 0-000a: Linked as a consumer to regulator.8 <4>[ 7.262732] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.271967] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.278342] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 7.279277] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.289167] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 7.292902] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.306239] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.315434] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.322980] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.332326] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.341061] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.348038] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.356785] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.365939] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.373192] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.381696] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.389114] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.398658] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.406130] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.416167] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.424948] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.431971] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 7.442505] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 7.477007] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 7.483559] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 7.491946] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 0 <4>[ 7.501495] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.510563] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.518023] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.526411] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.534097] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.543037] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.550858] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.560315] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.569064] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.576137] panel-simple panel-lcd: Dropping the link to regulator.0 done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-13238344/environment . /lava-13238344/environment / # /lava-13238344/bin/lava-test-runner /lava-13238344/0 /lava-13238344/bin/lava-test-runner /lava-13238344/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-13238344/0/tests/0_dmesg + cat uuid + <8>[ 8.274640] UUID=13238344_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 8.318582] <8>[ 8.358665] <8>[ 8.398978] + set +x <8>[ 8.408899] / #