Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. RomBOOT AT91Bootstrap 3.7.2-rc2-dirty (Tue 14 Apr 02:17:07 BST 2015) NAND: ONFI not supported NAND: Manufacturer ID: 0xec Chip ID: 0xda NAND: Disable On-Die ECC NAND: Press the recovery button (BP4) to recovery NAND: Using Software ECC NAND: Image: Copy 0x80000 bytes from 0x40000 to 0x21f00000 NAND: Done to load image U-Boot 2015.01 (Apr 14 2015 - 16:45:04) CPU: AT91SAM9G20 Crystal frequency: 18.432 MHz CPU clock : 396.288 MHz Master clock : 132.096 MHz DRAM: 64 MiB WARNING: Caches not enabled NAND: 256 MiB MMC: mci: 0 In: serial Out: serial Err: serial Net: macb0 Hit any key to stop autoboot: 3  0 U-Boot> setenv autoload no setenv autoload no U-Boot> setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff U-Boot> setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff U-Boot> dhcp dhcp macb0: Starting autonegotiation... macb0: Autonegotiation complete macb0: link up, 100Mbps full-duplex (lpa: 0xc1e1) BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 BOOTP broadcast 4 BOOTP broadcast 5 DHCP client bound to address 192.168.6.10 (3769 ms) U-Boot> setenv serverip 192.168.56.230 setenv serverip 192.168.56.230 U-Boot> tftp 0x22100000 585436/tftp-deploy-16x6u8b4/kernel/zImage tftp 0x22100000 585436/tftp-deploy-16x6u8b4/kernel/zImage macb0: link up, 100Mbps full-duplex (lpa: 0xc1e1) Using macb0 device TFTP from server 192.168.56.230; our IP address is 192.168.6.10; sending through gateway 192.168.6.1 Filename '585436/tftp-deploy-16x6u8b4/kernel/zImage'. Load address: 0x22100000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ####################### 1.3 MiB/s done Bytes transferred = 4144296 (3f3ca8 hex) U-Boot> tftp 0x23000000 585436/tftp-deploy-16x6u8b4/ramdisk/ramdisk.cpio.gz.uboot tftp 0x23000000 585436/tftp-deploy-16x6u8b4/ramdisk/ramdisk.cpio.gz.uboot macb0: link up, 100Mbps full-duplex (lpa: 0xc1e1) Using macb0 device TFTP from server 192.168.56.230; our IP address is 192.168.6.10; sending through gateway 192.168.6.1 Filename '585436/tftp-deploy-16x6u8b4/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x23000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################ 1.1 MiB/s done Bytes transferred = 5708763 (571bdb hex) U-Boot> setenv initrd_size ${filesize} setenv initrd_size ${filesize} U-Boot> tftp 0x22000000 585436/tftp-deploy-16x6u8b4/dtb/at91sam9g20ek.dtb tftp 0x22000000 585436/tftp-deploy-16x6u8b4/dtb/at91sam9g20ek.dtb macb0: link up, 100Mbps full-duplex (lpa: 0xc1e1) Using macb0 device TFTP from server 192.168.56.230; our IP address is 192.168.6.10; sending through gateway 192.168.6.1 Filename '585436/tftp-deploy-16x6u8b4/dtb/at91sam9g20ek.dtb'. Load address: 0x22000000 Loading: *## 1 MiB/s done Bytes transferred = 20023 (4e37 hex) U-Boot>setenv bootargs ' root=/dev/nfs rw nfsroot=192.168.56.230:/var/lib/lava/dispatcher/tmp/585436/extract-nfsrootfs-pyt6y_1d,tcp,hard,vers=3 cma=0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs ' root=/dev/nfs rw nfsroot=192.168.56.230:/var/lib/lava/dispatcher/tmp/585436/extract-nfsrootfs-pyt6y_1d,tcp,hard,vers=3 cma=0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' U-Boot> bootz 0x22100000 0x23000000 0x22000000 bootz 0x22100000 0x23000000 0x22000000 Kernel image @ 0x22100000 [ 0x000000 - 0x3f3ca8 ] ## Loading init Ramdisk from Legacy Image at 23000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 5708699 Bytes = 5.4 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 22000000 Booting using the fdt blob at 0x22000000 Using Device Tree in place at 22000000, end 22007e36 Starting kernel ... <6>Booting Linux on physical CPU 0x0 <5>Linux version 4.19.319-cip111 (KernelCI@build-j286368-arm-gcc-12-at91-dt-defconfig-4rskg) (gcc version 12.2.0 (Debian 12.2.0-14)) #1 Sat Jul 27 11:07:05 UTC 2024 <6>CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=0005317f <6>CPU: VIVT data cache, VIVT instruction cache <6>OF: fdt: Machine model: Atmel at91sam9g20ek <6>Memory policy: Data cache writeback <6>Built 1 zonelists, mobility grouping on. Total pages: 16256 <5>Kernel command line: root=/dev/nfs rw nfsroot=192.168.56.230:/var/lib/lava/dispatcher/tmp/585436/extract-nfsrootfs-pyt6y_1d,tcp,hard,vers=3 cma=0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) <6>Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) <6>Memory: 50852K/65536K available (5732K kernel code, 187K rwdata, 1940K rodata, 236K init, 122K bss, 14684K reserved, 0K cma-reserved) <5>Virtual kernel memory layout: <5> vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5> fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5> vmalloc : 0xc4800000 - 0xff800000 ( 944 MB) <5> lowmem : 0xc0000000 - 0xc4000000 ( 64 MB) <5> modules : 0xbf000000 - 0xc0000000 ( 16 MB) <5> .text : 0x(ptrval) - 0x(ptrval) (5734 kB) <5> .init : 0x(ptrval) - 0x(ptrval) ( 236 kB) <5> .data : 0x(ptrval) - 0x(ptrval) ( 188 kB) <5> .bss : 0x(ptrval) - 0x(ptrval) ( 123 kB) <6>NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>clocksource: pit: mask: 0x7ffffff max_cycles: 0x7ffffff, max_idle_ns: 7234361498 ns <6>Console: colour dummy device 80x30 <6>console [tty0] enabled <6>sched_clock: 32 bits at 128 Hz, resolution 7812500ns, wraps every 16777215996093750ns <6>Calibrating delay loop... 197.44 BogoMIPS (lpj=770048) <6>CPU: Testing write buffer coherency: ok <6>pid_max: default: 32768 minimum: 301 <6>Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) <6>Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) <6>Setting up static identity map for 0x20008400 - 0x2000847c <6>devtmpfs: initialized <6>clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 14931722236523437 ns <6>futex hash table entries: 256 (order: -1, 3072 bytes) <6>pinctrl core: initialized pinctrl subsystem <6>NET: Registered protocol family 16 <6>DMA: preallocated 256 KiB pool for atomic coherent allocations <6>AT91: PM: standby: standby, suspend: ulp0 <6>No ATAGs? <6>gpio-at91 fffff400.gpio: at address (ptrval) <6>gpio-at91 fffff600.gpio: at address (ptrval) <6>gpio-at91 fffff800.gpio: at address (ptrval) <6>pinctrl-at91 ahb:apb:pinctrl@fffff400: initialized AT91 pinctrl driver <6>clocksource: tcb_clksrc: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 115749784805 ns <6>AT91: Detected SoC: at91sam9g20, revision 1 <5>SCSI subsystem initialized <6>usbcore: registered new interface driver usbfs <6>usbcore: registered new interface driver hub <6>usbcore: registered new device driver usb <6>i2c-gpio i2c-gpio-0: using lines 23 (SDA) and 24 (SCL) <6>videodev: Linux video capture interface: v2.00 <6>pps_core: LinuxPPS API ver. 1 registered <6>pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>PTP clock support registered <6>Advanced Linux Sound Architecture Driver Initialized. <6>clocksource: Switched to clocksource tcb_clksrc <6>NET: Registered protocol family 2 <6>IP idents hash table entries: 2048 (order: 2, 16384 bytes) <6>tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes) <6>TCP established hash table entries: 1024 (order: 0, 4096 bytes) <6>TCP bind hash table entries: 1024 (order: 0, 4096 bytes) <6>TCP: Hash tables configured (established 1024 bind 1024) <6>UDP hash table entries: 256 (order: 0, 4096 bytes) <6>UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) <6>NET: Registered protocol family 1 <6>RPC: Registered named UNIX socket transport module. <6>RPC: Registered udp transport module. <6>RPC: Registered tcp transport module. <6>RPC: Registered tcp NFSv4.1 backchannel transport module. <6>Trying to unpack rootfs image as initramfs... <6>Freeing initrd memory: 5576K <5>Initialise system trusted keyrings <6>workingset: timestamp_bits=30 max_order=14 bucket_order=0 <5>Key type asymmetric registered <5>Asymmetric key parser 'x509' registered <6>io scheduler noop registered (default) <6>io scheduler mq-deadline registered <6>io scheduler kyber registered <6>fffff200.serial: ttyS0 at MMIO 0xfffff200 (irq = 16, base_baud = 8256000) is a ATMEL_SERIAL <6>console [ttyS0] enabled <6>fffb0000.serial: ttyS1 at MMIO 0xfffb0000 (irq = 26, base_baud = 8256000) is a ATMEL_SERIAL <6>fffb4000.serial: ttyS2 at MMIO 0xfffb4000 (irq = 27, base_baud = 8256000) is a ATMEL_SERIAL <6>brd: module loaded <6>loop: module loaded <6>ssc fffbc000.ssc: Atmel SSC device at 0x(ptrval) (irq 31) <6>Davicom DM9161A fffc4000.ethernet-ffffffff:00: attached PHY driver [Davicom DM9161A] (mii_bus:phy_addr=fffc4000.ethernet-ffffffff:00, irq=POLL) <6>macb fffc4000.ethernet eth0: Cadence MACB rev 0x0001010c at 0xfffc4000 irq 28 (a6:72:4e:7e:7a:f8) <6>ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>ehci-atmel: EHCI Atmel driver <6>ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>ohci-atmel: OHCI Atmel driver <6>at91_ohci 500000.ohci: USB Host Controller <6>at91_ohci 500000.ohci: new USB bus registered, assigned bus number 1 <6>at91_ohci 500000.ohci: irq 33, io mem 0x00500000 <6>usb usb1: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19 <6>usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>usb usb1: Product: USB Host Controller <6>usb usb1: Manufacturer: Linux 4.19.319-cip111 ohci_hcd <6>usb usb1: SerialNumber: at91 <6>hub 1-0:1.0: USB hub found <6>hub 1-0:1.0: 2 ports detected <6>usbcore: registered new interface driver cdc_acm <6>cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters <6>usbcore: registered new interface driver usb-storage <6>usbcore: registered new interface driver usbserial_generic <6>usbserial: USB Serial support registered for generic <6>usbcore: registered new interface driver ftdi_sio <6>usbserial: USB Serial support registered for FTDI USB Serial Device <6>usbcore: registered new interface driver pl2303 <6>usbserial: USB Serial support registered for pl2303 <6>udc: at91_udc version 3 May 2006 <6>g_serial gadget: Gadget Serial v2.4 <6>g_serial gadget: g_serial ready <6>rtc-at91sam9 fffffd20.rtc: rtc core: registered fffffd20.rtc as rtc0 <4>rtc-at91sam9 fffffd20.rtc: rtc0: SET TIME! <6>at91-reset fffffd00.rstc: Starting after general reset <3>at91_wdt fffffd40.watchdog: watchdog is disabled <4>at91_wdt: probe of fffffd40.watchdog failed with error -22 <6>atmel_mci fffa8000.mmc: version: 0x210 <6>atmel_mci fffa8000.mmc: using PDC <6>atmel_mci fffa8000.mmc: Atmel MCI controller at 0xfffa8000 irq 30, 1 slots <6>usbcore: registered new interface driver usbhid <6>usbhid: USB HID core driver <6>nand: device found, Manufacturer ID: 0xec, Chip ID: 0xda <6>nand: Samsung NAND 256MiB 3,3V 8-bit <6>nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 <6>Bad block table found at page 131008, version 0x01 <6>Bad block table found at page 130944, version 0x01 <6>nand_read_bbt: bad block at 0x000006120000 <6>nand_read_bbt: bad block at 0x00000d880000 <5>8 fixed-partitions partitions found on MTD device atmel_nand <5>Creating 8 MTD partitions on "atmel_nand": <5>0x000000000000-0x000000020000 : "at91bootstrap" <5>0x000000020000-0x000000060000 : "barebox" <5>0x000000060000-0x000000080000 : "bareboxenv" <5>0x000000080000-0x0000000a0000 : "bareboxenv2" <5>0x0000000a0000-0x0000000c0000 : "oftree" <5>0x0000000c0000-0x0000004c0000 : "kernel" <5>0x0000004c0000-0x000007cc0000 : "rootfs" <5>0x000007cc0000-0x000010000000 : "data" <6>iio iio:device0: Resolution used: 10 bits <6>iio iio:device0: not support touchscreen in the adc compatible string. <4>wm8731 1-001b: Assuming static MCLK <4>wm8731 1-001b: 1-001b supply AVDD not found, using dummy regulator <6>wm8731 1-001b: Linked as a consumer to regulator.0 <4>wm8731 1-001b: 1-001b supply HPVDD not found, using dummy regulator <4>wm8731 1-001b: 1-001b supply DCVDD not found, using dummy regulator <4>wm8731 1-001b: 1-001b supply DBVDD not found, using dummy regulator <3>at91sam9g20ek-audio sound: Failed to get MCLK <4>at91sam9g20ek-audio: probe of sound failed with error -2 <6>NET: Registered protocol family 10 <6>Segment Routing with IPv6 <6>sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>NET: Registered protocol family 17 <5>Loading compiled-in X.509 certificates <6>input: gpio_keys as /devices/platform/gpio_keys/input/input0 <3>rtc-at91sam9 fffffd20.rtc: hctosys: unable to read the hardware clock <6>IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>macb fffc4000.ethernet eth0: link up (100/Full) <6>IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>Sending DHCP requests .., OK <6>IP-Config: Got DHCP answer from 192.168.6.1, my address is 192.168.6.10 <6>IP-Config: Complete: <6> device=eth0, hwaddr=a6:72:4e:7e:7a:f8, ipaddr=192.168.6.10, mask=255.255.255.0, gw=192.168.6.1 <6> host=192.168.6.10, domain=, nis-domain=(none) <6> bootserver=192.168.6.1, rootserver=192.168.56.230, rootpath= <6> nameserver0=10.255.253.1 <5>cfg80211: Loading compiled-in X.509 certificates for regulatory database <5>cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' <5>cfg80211: Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600' <6>ALSA device list: <6> No soundcards found. <4>platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 <6>cfg80211: failed to load regulatory.db <6>Freeing unused kernel memory: 236K <4>This architecture does not have kernel memory protection. <6>Run /init as init process Loading, please wait... Starting systemd-udevd version 252.22-1~deb12u1 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. Begin: Waiting up to 180 secs for any network device to become available ... done. IP-Config: eth0 hardware address a6:72:4e:7e:7a:f8 mtu 1500 DHCP IP-Config: eth0 guessed broadcast address 192.168.6.255 IP-Config: eth0 complete (dhcp from 192.168.6.1): address: 192.168.6.10 broadcast: 192.168.6.255 netmask: 255.255.255.0 gateway: 192.168.6.1 dns0 : 10.255.253.1 dns1 : 0.0.0.0 rootserver: 192.168.6.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>systemd[1]: System time before build time, advancing clock. <27>systemd[1]: Failed to find module 'autofs4' <27>systemd[1]: Failed to mount tmpfs at /sys/fs/cgroup: No such file or directory <27>systemd[1]: Failed to mount cgroup at /sys/fs/cgroup/systemd: No such file or directory [[0;1;31m!!!!!![0m] Failed to mount API filesystems. <24>systemd[1]: Freezing execution. <5>random: crng init done # # # # #