Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. GXL:BL1:9ac50e:a1974b;FEAT:ADFC318C;POC:3;RCY:0;EMMC:0;READ:0;CHK:AA;SD:0;READ:0;0.0;CHK:0; no sdio debug board detected TE: 171164 BL2 Built : 14:59:36, Aug 9 2017. gxl ge8c6a83 - xiaobo.gu@droid12 set vcck to 1120 mv set vddee to 1000 mv Board ID = 6 CPU clk: 1200MHz DQS-corr enabled DDR scramble enabled DDR3 chl: Rank0+1 @ 768MHz - PASS Rank0: 1024MB(auto)-2T-11 Rank1: 1024MB(auto)-2T-11 DataBus test pass! AddrBus test pass! Load fip header from SD, src: 0x0000c200, des: 0x01400000, size: 0x00004000 New fip structure! Load bl30 from SD, src: 0x00010200, des: 0x01100000, size: 0x0000d600 Load bl31 from SD, src: 0x00020200, des: 0x05100000, size: 0x0002c600 Load bl33 from SD, src: 0x00050200, des: 0x01000000, size: 0x00078a00 NOTICE: BL3-1: v1.0(release):801e730 NOTICE: BL3-1: Built : 22:09:38, Aug 10 2017 [BL31]: GXL CPU setup! mpu_config_enable:ok [Image: gxl_v1.1.3244-a3237e2 2017-08-16 14:01:18 hong.guo@droid04] OPS=0x82 6 27 29 62 b9 10 78 3d dd 3 a2 bd [0.524839 Inits done] secure task start! high task start! low task start! ERROR: Error initializing runtime service opteed_fast U-Boot 2018.07-rc2-00043-gf630f14 (Jul 26 2018 - 15:02:54 +0200) khadas-vim DRAM: 2 GiB MMC: mmc@70000: 0, mmc@72000: 1, mmc@74000: 2 In: serial@4c0 Out: serial@4c0 Err: serial@4c0 [BL31]: tee size: 0 [BL31]: tee size: 0 clock 5 has rate 666666666 clock 126 has rate 666666666 clock 128 has rate 666666666 clock 5 has rate 666666666 clock 126 has rate 666666666 clock 128 has rate 666666666 clock 128 has new rate 666666666 clock 6 has rate 500000000 clock 133 has rate 500000000 clock 135 has rate 500000000 clock 6 has rate 500000000 clock 133 has rate 500000000 clock 6 has rate 500000000 clock 133 has rate 500000000 clock 135 has rate 250000000 clock 135 has new rate 250000000 Enabled VPU Power Domain Enabled 5V regulator Net: Warning: ethernet@c9410000 (eth0) using random MAC address - 02:e6:dd:e3:d8:07 eth0: ethernet@c9410000 Hit any key to stop autoboot: 2  1  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp Speed: 100, full duplex BOOTP broadcast 1 DHCP client bound to address 10.201.4.166 (7 ms) => setenv serverip 10.201.1.6 setenv serverip 10.201.1.6 => tftp 0x13000000 2124902/tftp-deploy-6ger6kgs/kernel/Image tftp 0x13000000 2124902/tftp-deploy-6ger6kgs/kernel/Image Speed: 100, full duplex Using ethernet@c9410000 device TFTP from server 10.201.1.6; our IP address is 10.201.4.166 Filename '2124902/tftp-deploy-6ger6kgs/kernel/Image'. Load address: 0x13000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# #####################################################T