[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.37 (4 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 6692253/tftp-deploy-ettst9ki/kernel/zImage tftp 0x10000000 6692253/tftp-deploy-ettst9ki/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '6692253/tftp-deploy-ettst9ki/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######### 10 MiB/s done Bytes transferred = 9667072 (938200 hex) => tftp 0x14000000 6692253/tftp-deploy-ettst9ki/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 6692253/tftp-deploy-ettst9ki/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '6692253/tftp-deploy-ettst9ki/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################### 10.6 MiB/s done Bytes transferred = 12138426 (b937ba hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 6692253/tftp-deploy-ettst9ki/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 6692253/tftp-deploy-ettst9ki/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '6692253/tftp-deploy-ettst9ki/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 5.8 MiB/s done Bytes transferred = 42397 (a59d hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/6692253/extract-nfsrootfs-noz_p1sm,tcp,hard ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/6692253/extract-nfsrootfs-noz_p1sm,tcp,hard ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x938200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 12138362 Bytes = 11.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d59c Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.126-cip9 (KernelCI@build-j265046-arm-gcc-10-multi-v7-defconfig-slqxw) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Mon Jun 27 22:53:25 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/6692253/extract-nfsrootfs-noz_p1sm,tcp,hard ip=dhcp [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 937536K/1048576K available (13312K kernel code, 2230K rwdata, 5340K rodata, 2048K init, 425K bss, 45504K reserved, 65536K cma-reserved, 196608K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] L2C-310 errata 752271 769419 enabled [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 [ 0.000000] Switching to timer-based delay loop, resolution 333ns [ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns [ 0.000026] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns [ 0.004165] Console: colour dummy device 80x30 [ 0.004217] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) [ 0.004236] pid_max: default: 32768 minimum: 301 [ 0.004417] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.004442] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.005071] CPU: Testing write buffer coherency: ok [ 0.005112] CPU0: Spectre v2: using BPIALL workaround [ 0.005361] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.006052] Setting up static identity map for 0x10300000 - 0x103000ac [ 0.007719] rcu: Hierarchical SRCU implementation. [ 0.011541] EFI services will not be available. [ 0.011851] smp: Bringing up secondary CPUs ... [ 0.012640] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.012649] CPU1: Spectre v2: using BPIALL workaround [ 0.013558] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.013566] CPU2: Spectre v2: using BPIALL workaround [ 0.014443] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.014451] CPU3: Spectre v2: using BPIALL workaround [ 0.014566] smp: Brought up 1 node, 4 CPUs [ 0.014581] SMP: Total of 4 processors activated (24.00 BogoMIPS). [ 0.014590] CPU: All CPU(s) started in SVC mode. [ 0.015162] devtmpfs: initialized [ 0.022492] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.022732] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.022756] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.025864] pinctrl core: initialized pinctrl subsystem [ 0.027709] DMI not present or invalid. [ 0.028555] NET: Registered protocol family 16 [ 0.032061] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.034426] thermal_sys: Registered thermal governor 'step_wise' [ 0.034611] cpuidle: using governor menu [ 0.034795] CPU identified as i.MX6Q, silicon rev 1.2 [ 0.203276] vdd1p1: supplied by regulator-dummy [ 0.210252] vdd3p0: supplied by regulator-dummy [ 0.217129] vdd2p5: supplied by regulator-dummy [ 0.224047] vddarm: supplied by regulator-dummy [ 0.231155] vddpu: supplied by regulator-dummy [ 0.237895] vddsoc: supplied by regulator-dummy [ 0.554793] No ATAGs? [ 0.554941] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.554952] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.559199] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver [ 0.565381] Serial: AMBA PL011 UART driver [ 0.568023] printk: console [ramoops-1] enabled [ 0.568253] pstore: Registered ramoops as persistent store backend [ 0.568268] ramoops: using 0x10000@0x30000000, ecc: 0 [ 0.594634] mxs-dma 110000.dma-apbh: initialized [ 0.602443] iommu: Default domain type: Translated [ 0.602873] vgaarb: loaded [ 0.603766] SCSI subsystem initialized [ 0.604350] usbcore: registered new interface driver usbfs [ 0.604412] usbcore: registered new interface driver hub [ 0.604462] usbcore: registered new device driver usb [ 0.606018] i2c i2c-0: IMX I2C adapter registered [ 0.607376] i2c i2c-1: IMX I2C adapter registered [ 0.608197] i2c i2c-2: IMX I2C adapter registered [ 0.609698] pps_core: LinuxPPS API ver. 1 registered [ 0.609712] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.609741] PTP clock support registered [ 0.613645] clocksource: Switched to clocksource mxc_timer1 [ 1.665576] NET: Registered protocol family 2 [ 1.666035] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 1.667204] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 1.667250] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 1.667339] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 1.667485] TCP: Hash tables configured (established 8192 bind 8192) [ 1.667710] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.667763] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.667945] NET: Registered protocol family 1 [ 1.668690] RPC: Registered named UNIX socket transport module. [ 1.668706] RPC: Registered udp transport module. [ 1.668716] RPC: Registered tcp transport module. [ 1.668727] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.668744] PCI: CLS 0 bytes, default 64 [ 1.669222] Trying to unpack rootfs image as initramfs... [ 2.624062] Freeing initrd memory: 11856K [ 2.624601] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 2.624943] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 2.626813] Initialise system trusted keyrings [ 2.627222] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 2.633018] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2.633869] NFS: Registering the id_resolver key type [ 2.633956] Key type id_resolver registered [ 2.633968] Key type id_legacy registered [ 2.634075] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 2.634088] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 2.634126] ntfs: driver 2.1.32 [Flags: R/O]. [ 2.634612] Key type asymmetric registered [ 2.634629] Asymmetric key parser 'x509' registered [ 2.634692] bounce: pool size: 64 pages [ 2.634738] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 2.634752] io scheduler mq-deadline registered [ 2.634763] io scheduler kyber registered [ 2.679108] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 2.679135] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 2.741184] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 2.745868] SuperH (H)SCI(F) driver initialized [ 2.746910] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX [ 2.747942] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX [ 3.576029] printk: console [ttymxc1] enabled [ 3.581804] msm_serial: driver initialized [ 3.586215] STMicroelectronics ASC driver initialized [ 3.593305] STM32 USART driver initialized [ 3.609087] panel-simple panel-lcd: supply power not found, using dummy regulator [ 3.616763] panel-simple panel-lcd: Specify missing connector_type [ 3.623349] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 3.640023] brd: module loaded [ 3.653079] loop: module loaded [ 3.660214] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 [ 3.668166] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 [ 3.676195] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 [ 3.684401] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 [ 3.692139] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator [ 3.699649] ahci-imx 2200000.sata: supply phy not found, using dummy regulator [ 3.706953] ahci-imx 2200000.sata: supply target not found, using dummy regulator [ 3.717288] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled [ 3.724327] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 3.733128] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 3.743713] scsi host0: ahci-imx [ 3.747346] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 [ 3.767910] CAN device driver interface [ 3.773158] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 3.782469] pps pps0: new PPS source ptp0 [ 3.804610] fec 2188000.ethernet eth0: registered PHC device 0 [ 3.811986] e1000e: Intel(R) PRO/1000 Network Driver [ 3.816984] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 3.822970] igb: Intel(R) Gigabit Ethernet Network Driver [ 3.828393] igb: Copyright (c) 2007-2014 Intel Corporation. [ 3.840321] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 3.847793] usbcore: registered new interface driver pegasus [ 3.853517] usbcore: registered new interface driver asix [ 3.858957] usbcore: registered new interface driver ax88179_178a [ 3.865105] usbcore: registered new interface driver cdc_ether [ 3.870996] usbcore: registered new interface driver smsc75xx [ 3.876810] usbcore: registered new interface driver smsc95xx [ 3.882595] usbcore: registered new interface driver net1080 [ 3.888310] usbcore: registered new interface driver cdc_subset [ 3.894281] usbcore: registered new interface driver zaurus [ 3.899930] usbcore: registered new interface driver cdc_ncm [ 3.909327] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.915884] ehci-pci: EHCI PCI platform driver [ 3.920371] ehci-platform: EHCI generic platform driver [ 3.925931] ehci-orion: EHCI orion driver [ 3.930172] SPEAr-ehci: EHCI SPEAr driver [ 3.934402] ehci-st: EHCI STMicroelectronics driver [ 3.939472] ehci-exynos: EHCI Exynos driver [ 3.943877] ehci-atmel: EHCI Atmel driver [ 3.948080] tegra-ehci: Tegra EHCI driver [ 3.952315] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.958534] ohci-pci: OHCI PCI platform driver [ 3.963025] ohci-platform: OHCI generic platform driver [ 3.968543] SPEAr-ohci: OHCI SPEAr driver [ 3.972748] ohci-st: OHCI STMicroelectronics driver [ 3.977837] ohci-atmel: OHCI Atmel driver [ 3.982967] usbcore: registered new interface driver usb-storage [ 3.997375] i2c /dev entries driver [ 4.020962] sdhci: Secure Digital Host Controller Interface driver [ 4.027184] sdhci: Copyright(c) Pierre Ossman [ 4.034410] Synopsys Designware Multimedia Card Interface Driver [ 4.042437] sdhci-pltfm: SDHCI platform and OF driver helper [ 4.049479] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO [ 4.053815] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO [ 4.054519] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO [ 4.064787] ledtrig-cpu: registered to indicate activity on CPUs [ 4.071886] usbcore: registered new interface driver usbhid [ 4.077499] usbhid: USB HID core driver [ 4.088067] NET: Registered protocol family 10 [ 4.093541] Segment Routing with IPv6 [ 4.093846] ata1: SATA link down (SStatus 0 SControl 300) [ 4.097280] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 4.102661] ahci-imx 2200000.sata: no device found, disabling link. [ 4.108832] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA [ 4.109157] NET: Registered protocol family 17 [ 4.109169] can: controller area network core [ 4.109243] NET: Registered protocol family 29 [ 4.109248] can: raw protocol [ 4.109256] can: broadcast manager protocol [ 4.109266] can: netlink gateway - max_hops=1 [ 4.109667] Key type dns_resolver registered [ 4.114873] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug [ 4.116760] ThumbEE CPU extension supported. [ 4.116772] Registering SWP/SWPB emulation handler [ 4.121989] Loading compiled-in X.509 certificates [ 4.122499] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA [ 4.164424] mmc2: new high speed SDHC card at address e624 [ 4.172425] pstore: Using crash dump compression: deflate [ 4.180170] mmcblk2: mmc2:e624 SL16G 14.8 GiB [ 4.206162] panel-simple panel-lcd: supply power not found, using dummy regulator [ 4.213836] panel-simple panel-lcd: Specify missing connector_type [ 4.221760] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 4.237233] GPT:Primary header thinks Alt. header is not at the end of the disk. [ 4.241044] imx_usb 2184200.usb: No over current polarity defined [ 4.244710] GPT:29296874 != 31116287 [ 4.244718] GPT:Alternate GPT header not at the end of the disk. [ 4.244725] GPT:29296874 != 31116287 [ 4.244731] GPT: Use GNU Parted to correct GPT errors. [ 4.244818] mmcblk2: p1 p2 p3 [ 4.255048] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 4.277237] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 [ 4.313610] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 4.320337] hub 1-0:1.0: USB hub found [ 4.324263] hub 1-0:1.0: 1 port detected [ 4.330786] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C [ 4.346708] panel-simple panel-lcd: supply power not found, using dummy regulator [ 4.354360] panel-simple panel-lcd: Specify missing connector_type [ 4.362044] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 4.374114] panel-simple panel-lcd: supply power not found, using dummy regulator [ 4.381720] panel-simple panel-lcd: Specify missing connector_type [ 4.389384] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 4.399147] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 4.410870] panel-simple panel-lcd: supply power not found, using dummy regulator [ 4.418548] panel-simple panel-lcd: Specify missing connector_type [ 4.426336] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 4.439895] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) [ 4.653585] usb 1-1: new high-speed USB device number 2 using ci_hdrc [ 4.855249] hub 1-1:1.0: USB hub found [ 4.859229] hub 1-1:1.0: 3 ports detected [ 4.869762] panel-simple panel-lcd: supply power not found, using dummy regulator [ 4.877508] panel-simple panel-lcd: Specify missing connector_type [ 4.885636] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.594033] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 7.613641] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 7.643583] Sending DHCP requests ., OK [ 7.687522] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.37 [ 7.695585] IP-Config: Complete: [ 7.698844] device=eth0, hwaddr=00:19:b8:08:f0:fd, ipaddr=192.168.201.37, mask=255.255.255.0, gw=192.168.201.1 [ 7.709361] host=imx6q-sabrelite-lava-cbg-7, domain=lava-rack, nis-domain=(none) [ 7.717246] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= [ 7.717258] nameserver0=192.168.201.1 [ 7.737690] Freeing unused kernel memory: 2048K [ 7.774593] Run /init as init process Loading, please wait... Starting version 247.3-7 [ 8.636576] imx-ipuv3 2400000.ipu: IPUv3H probed [ 8.646448] panel-simple panel-lcd: supply power not found, using dummy regulator [ 8.667301] panel-simple panel-lcd: Specify missing connector_type [ 8.669512] imx-ipuv3 2800000.ipu: IPUv3H probed [ 8.675867] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 8.695350] panel-simple panel-lcd: supply power not found, using dummy regulator [ 8.703669] panel-simple panel-lcd: Specify missing connector_type [ 8.716843] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 8.724982] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 8.733317] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 8.741750] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 8.750154] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 8.774743] panel-simple panel-lcd: supply power not found, using dummy regulator [ 8.782413] panel-simple panel-lcd: Specify missing connector_type [ 8.795164] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 8.823676] caam 2100000.crypto: Entropy delay = 3200 [ 8.829200] panel-simple panel-lcd: supply power not found, using dummy regulator [ 8.836932] panel-simple panel-lcd: Specify missing connector_type [ 8.845453] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 8.889537] caam 2100000.crypto: Instantiated RNG4 SH0 [ 8.950301] caam 2100000.crypto: Instantiated RNG4 SH1 [ 8.955219] sgtl5000 0-000a: sgtl5000 revision 0x11 [ 8.955497] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) [ 8.966990] caam 2100000.crypto: job rings = 2, qi = 0 [ 8.970195] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum [ 8.972739] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator [ 8.987661] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests [ 8.996045] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator [ 9.003900] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests [ 9.017708] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) [ 9.025191] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) [ 9.032574] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) [ 9.039210] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 [ 9.056100] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 [ 9.062993] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 [ 9.069186] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 [ 9.077175] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 [ 9.085618] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 9.094015] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 9.102324] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 9.110664] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 9.127597] panel-simple panel-lcd: supply power not found, using dummy regulator [ 9.135425] panel-simple panel-lcd: Specify missing connector_type [ 9.144958] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 9.157827] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 9.166227] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 9.174539] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 9.182807] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 9.410069] caam algorithms registered in /proc/crypto [ 9.416572] caam 2100000.crypto: registering rng-caam [ 9.427687] panel-simple panel-lcd: supply power not found, using dummy regulator [ 9.435360] panel-simple panel-lcd: Specify missing connector_type [ 9.443611] panel-simple panel-lvds0: supply power not found, using dummy regulator Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done[ 9.465084] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) . Begin: Running /scripts/nfs-pr[ 9.474819] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) emount ... done. [ 9.485843] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 9.495537] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 9.604086] random: crng init done IP-Config: eth0 hardware address 00:19:b8:08:f0:fd mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.37 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-7 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 10.383584] systemd[1]: System time before build time, advancing clock. [ 10.439637] systemd[1]: systemd 247.3-7 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) [ 10.462691] systemd[1]: Detected architecture arm. Welcome to [1mDebian GNU/Linux 11 (bullseye)[0m! [ 10.505637] systemd[1]: Set hostname to . [ 11.247549] systemd[1]: Queued start job for default target Graphical Interface. [ 11.257126] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. [ 11.269565] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) [ 11.279295] systemd[1]: Created slice system-getty.slice. [[0;32m OK [0m] Created slice [0;1;39msystem-getty.slice[0m. [ 11.314970] systemd[1]: Created slice system-modprobe.slice. [[0;32m OK [0m] Created slice [0;1;39msystem-modprobe.slice[0m. [ 11.355119] systemd[1]: Created slice system-serial\x2dgetty.slice. [[0;32m OK [0m] Created slice [0;1;39msystem-serial\x2dgetty.slice[0m. [ 11.394074] systemd[1]: Created slice User and Session Slice. [[0;32m OK [0m] Created slice [0;1;39mUser and Session Slice[0m. [ 11.434384] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [[0;32m OK [0m] Started [0;1;39mDispatch Password …ts to Console Directory Watch[0m. [ 11.474493] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [[0;32m OK [0m] Started [0;1;39mForward Password R…uests to Wall Directory Watch[0m. [ 11.513865] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. [ 11.525797] systemd[1]: Reached target Local Encrypted Volumes. [[0;32m OK [0m] Reached target [0;1;39mLocal Encrypted Volumes[0m. [ 11.564552] systemd[1]: Reached target Paths. [[0;32m OK [0m] Reached target [0;1;39mPaths[0m. [ 11.594068] systemd[1]: Reached target Remote File Systems. [[0;32m OK [0m] Reached target [0;1;39mRemote File Systems[0m. [ 11.633883] systemd[1]: Reached target Slices. [[0;32m OK [0m] Reached target [0;1;39mSlices[0m. [ 11.664158] systemd[1]: Reached target Swap. [[0;32m OK [0m] Reached target [0;1;39mSwap[0m. [ 11.694673] systemd[1]: Listening on initctl Compatibility Named Pipe. [[0;32m OK [0m] Listening on [0;1;39minitctl Compatibility Named Pipe[0m. [ 11.770364] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. [ 11.779830] systemd[1]: Listening on Journal Socket (/dev/log). [[0;32m OK [0m] Listening on [0;1;39mJournal Socket (/dev/log)[0m. [ 11.815093] systemd[1]: Listening on Journal Socket. [[0;32m OK [0m] Listening on [0;1;39mJournal Socket[0m. [ 11.856040] systemd[1]: Listening on Network Service Netlink Socket. [[0;32m OK [0m] Listening on [0;1;39mNetwork Service Netlink Socket[0m. [ 11.896725] systemd[1]: Listening on udev Control Socket. [[0;32m OK [0m] Listening on [0;1;39mudev Control Socket[0m. [ 11.934986] systemd[1]: Listening on udev Kernel Socket. [[0;32m OK [0m] Listening on [0;1;39mudev Kernel Socket[0m. [ 11.974213] systemd[1]: Condition check resulted in Huge Pages File System being skipped. [ 11.982889] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. [ 11.995136] systemd[1]: Mounting Kernel Debug File System... Mounting [0;1;39mKernel Debug File System[0m... [ 12.040174] systemd[1]: Mounting Kernel Trace File System... Mounting [0;1;39mKernel Trace File System[0m... [ 12.079115] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting [0;1;39mCreate list of st…odes for the current kernel[0m... [ 12.130206] systemd[1]: Starting Load Kernel Module configfs... Starting [0;1;39mLoad Kernel Module configfs[0m... [ 12.167248] systemd[1]: Starting Load Kernel Module drm... Starting [0;1;39mLoad Kernel Module drm[0m... [ 12.206624] systemd[1]: Starting Load Kernel Module fuse... Starting [0;1;39mLoad Kernel Module fuse[0m... [ 12.246556] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. [ 12.259590] systemd[1]: Starting Journal Service... Starting [0;1;39mJournal Service[0m... [ 12.301666] systemd[1]: Starting Load Kernel Modules... Starting [0;1;39mLoad Kernel Modules[0m... [ 12.337276] systemd[1]: Starting Remount Root and Kernel File Systems... Starting [0;1;39mRemount Root and Kernel File Systems[0m... [ 12.376900] systemd[1]: Starting Coldplug All udev Devices... Starting [0;1;39mColdplug All udev Devices[0m... [ 12.419292] systemd[1]: Mounted Kernel Debug File System. [[0;32m OK [0m] Mounted [0;1;39mKernel Debug File System[0m. [ 12.454269] systemd[1]: Mounted Kernel Trace File System. [[0;32m OK [0m] Mounted [0;1;39mKernel Trace File System[0m. [ 12.494739] systemd[1]: Finished Create list of static device nodes for the current kernel. [[0;32m OK [0m] Finished [0;1;39mCreate list of st… nodes for the current kernel[0m. [ 12.549659] systemd[1]: Started Journal Service. [[0;32m OK [0m] Started [0;1;39mJournal Service[0m. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Module configfs[0m. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Module drm[0m. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Module fuse[0m. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Modules[0m. [[0;32m OK [0m] Finished [0;1;39mRemount Root and Kernel File Systems[0m. Mounting [0;1;39mKernel Configuration File System[0m... Starting [0;1;39mFlush Journal to Persistent Storage[0m... Starting [0;1;39mLoad/Save Random Seed[0m... [ 12.847288] systemd-journald[265]: Received client request to flush runtime journal. Starting [0;1;39mApply Kernel Variables[0m... Starting [0;1;39mCreate System Users[0m... [[0;32m OK [0m] Mounted [0;1;39mKernel Configuration File System[0m. [[0;32m OK [0m] Finished [0;1;39mLoad/Save Random Seed[0m. [[0;32m OK [0m] Finished [0;1;39mApply Kernel Variables[0m. [[0;32m OK [0m] Finished [0;1;39mCreate System Users[0m. Starting [0;1;39mCreate Static Device Nodes in /dev[0m... [[0;32m OK [0m] Finished [0;1;39mFlush Journal to Persistent Storage[0m. [[0;32m OK [0m] Finished [0;1;39mCreate Static Device Nodes in /dev[0m. [[0;32m OK [0m] Reached target [0;1;39mLocal File Systems (Pre)[0m. [[0;32m OK [0m] Reached target [0;1;39mLocal File Systems[0m. Starting [0;1;39mCreate Volatile Files and Directories[0m... Starting [0;1;39mRule-based Manage…for Device Events and Files[0m... [[0;32m OK [0m] Started [0;1;39mRule-based Manager for Device Events and Files[0m. [[0;32m OK [0m] Finished [0;1;39mCreate Volatile Files and Directories[0m. Starting [0;1;39mNetwork Service[0m... Starting [0;1;39mUpdate UTMP about System Boot/Shutdown[0m... [[0;32m OK [0m] Finished [0;1;39mColdplug All udev Devices[0m. [[0;32m OK [0m] Finished [0;1;39mUpdate UTMP about System Boot/Shutdown[0m. [[0;32m OK [0m] Reached target [0;1;39mSystem Initialization[0m. [[0;32m OK [0m] Started [0;1;39mDaily apt download activities[0m. [[0;32m OK [0m] Started [0;1;39mDaily apt upgrade and clean activities[0m. [[0;32m OK [0m] Started [0;1;39mPeriodic ext4 Onli…ata Check for All Filesystems[0m. [[0;32m OK [0m] Started [0;1;39mDiscard unused blocks once a week[0m. [[0;32m OK [0m] Started [0;1;39mDaily Cleanup of Temporary Directories[0m. [[0;32m OK [0m] Reached target [0;1;39mTimers[0m. [[0;32m OK [0m] Listening on [0;1;39mD-Bus System Message Bus Socket[0m. [[0;32m OK [0m] Reached target [0;1;39mSockets[0m. [[0;32m OK [0m] Reached target [0;1;39mBasic System[0m. [[0;32m OK [0m] Started [0;1;39mD-Bus System Message Bus[0m. Starting [0;1;39mRemove Stale Onli…t4 Metadata Check Snapshots[0m... Starting [0;1;39mUser Login Management[0m... [[0;32m OK [0m] Started [0;1;39mNetwork Service[0m. [[0;32m OK [0m] Reached target [0;1;39mHardware activated USB gadget[0m. Starting [0;1;39mNetwork Name Resolution[0m... [[0;32m OK [0m] Found device [0;1;39m/dev/ttymxc1[0m. [[0;32m OK [0m] Finished [0;1;39mRemove Stale Onli…ext4 Metadata Check Snapshots[0m. [[0;32m OK [0m] Started [0;1;39mNetwork Name Resolution[0m. [[0;32m OK [0m] Started [0;1;39mUser Login Management[0m. [[0;32m OK [0m] Reached target [0;1;39mNetwork[0m. [[0;32m OK [0m] Reached target [0;1;39mHost and Network Name Lookups[0m. [[0;32m OK [0m] Listening on [0;1;39mLoad/Save RF …itch Status /dev/rfkill Watch[0m. Starting [0;1;39mPermit User Sessions[0m... [[0;32m OK [0m] Finished [0;1;39mPermit User Sessions[0m. [[0;32m OK [0m] Started [0;1;39mGetty on tty1[0m. [[0;32m OK [0m] Started [0;1;39mSerial Getty on ttymxc1[0m. [[0;32m OK [0m] Reached target [0;1;39mLogin Prompts[0m. [[0;32m OK [0m] Reached target [0;1;39mMulti-User System[0m. [[0;32m OK [0m] Reached target [0;1;39mGraphical Interface[0m. Starting [0;1;39mUpdate UTMP about System Runlevel Changes[0m... [[0;32m OK [0m] Finished [0;1;39mUpdate UTMP about System Runlevel Changes[0m. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 5.10.126-cip9 #1 SMP Mon Jun 27 22:53:25 UTC 2022 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/6692253/extract-nfsrootfs-noz_p1sm' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/6692253/extract-nfsrootfs-noz_p1sm' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-6692253/environment . /lava-6692253/environment / # /lava-6692253/bin/lava-test-runner /lava-6692253/0 /lava-6692253/bin/lava-test-runner /lava-6692253/0 + export TESTRUN_ID=0_dmesg + cd /lava-6692253/0/tests/0_dmesg + cat uuid + UUID=6692253_1.6.2.4.1[ 26.081759] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh [ 26.165319] [ 26.232388] [ 26.299521] + set[ 26.308830] +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-6692253/environment / # . /lava-6692253/environment/lava-6692253/bin/lava-test-runner /lava-6692253/1 / # /lava-6692253/bin/lava-test-runner /lava-6692253/1 + export TESTRUN_ID=1_bootrr + cd /lava-6692253/1/tests/1_bootrr + cat uuid + UUID=6692253_1.6.2.4.5[ 26.891792] + set +x + export PATH=/opt/bootrr/helpers:/lava-6692253/1/../bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin + cd /opt/bootrr + sh helpers/bootrr-auto /lava-6692253/1/../bin/lava-test-case [ 27.997114] + set +x[ 28.029389] / #