Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. U-Boot SPL 2020.04-rc3-00189-gb4c87c9da9 (Apr 02 2020 - 09:37:57 +0200) DRAM: 1024 MiB Trying to boot from MMC1 U-Boot 2020.04-rc3-00189-gb4c87c9da9 (Apr 02 2020 - 09:37:57 +0200) Allwinner Technology CPU: Allwinner H3 (SUN8I 1680) Model: Banana Pi BPI-M2-Plus H3 DRAM: 1 GiB MMC: Device 'mmc@1c11000': seq 1 is in use by 'mmc@1c10000' mmc@1c0f000: 0, mmc@1c10000: 2, mmc@1c11000: 1 Loading Environment from FAT... *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Allwinner mUSB OTG (Peripheral) Net: phy interface7 eth0: ethernet@1c30000 Warning: usb_ether using MAC address from ROM , eth1: usb_ether starting USB... Bus usb@1c1a000: USB EHCI 1.00 Bus usb@1c1a400: USB OHCI 1.0 Bus usb@1c1b000: USB EHCI 1.00 Bus usb@1c1b400: USB OHCI 1.0 Bus usb@1c1c000: USB EHCI 1.00 Bus usb@1c1c400: USB OHCI 1.0 scanning bus usb@1c1a000 for devices... 1 USB Device(s) found scanning bus usb@1c1a400 for devices... 1 USB Device(s) found scanning bus usb@1c1b000 for devices... 1 USB Device(s) found scanning bus usb@1c1b400 for devices... 1 USB Device(s) found scanning bus usb@1c1c000 for devices... 1 USB Device(s) found scanning bus usb@1c1c400 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp ethernet@1c30000 Waiting for PHY auto negotiation to complete........ done BOOTP broadcast 1 BOOTP broadcast 2 DHCP client bound to address 10.201.3.139 (260 ms) => setenv serverip 10.201.1.11 setenv serverip 10.201.1.11 => tftp 0x40000000 2190477/tftp-deploy-54irybcf/kernel/zImage tftp 0x40000000 2190477/tftp-deploy-54irybcf/kernel/zImage Using ethernet@1c30000 device TFTP from server 10.201.1.11; our IP address is 10.201.3.139 Filename '2190477/tftp-deploy-54irybcf/kernel/zImage'. Load address: 0x40000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######### 7.9 MiB/s done Bytes transferred = 9662976 (937200 hex) => tftp 0x44300000 2190477/tftp-deploy-54irybcf/ramdisk/ramdisk.cpio.gz.uboot tftp 0x44300000 2190477/tftp-deploy-54irybcf/ramdisk/ramdisk.cpio.gz.uboot Using ethernet@1c30000 device TFTP from server 10.201.1.11; our IP address is 10.201.3.139 Filename '2190477/tftp-deploy-54irybcf/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x44300000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ##################################################### 7.9 MiB/s done Bytes transferred = 16044897 (f4d361 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x44000000 2190477/tftp-deploy-54irybcf/dtb/sun8i-h3-bananapi-m2-plus.dtb tftp 0x44000000 2190477/tftp-deploy-54irybcf/dtb/sun8i-h3-bananapi-m2-plus.dtb Using ethernet@1c30000 device TFTP from server 10.201.1.11; our IP address is 10.201.3.139 Filename '2190477/tftp-deploy-54irybcf/dtb/sun8i-h3-bananapi-m2-plus.dtb'. Load address: 0x44000000 Loading: *## 4.4 MiB/s done Bytes transferred = 23202 (5aa2 hex) => setenv bootargs 'console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x40000000 0x44300000 0x44000000 bootz 0x40000000 0x44300000 0x44000000 ## Loading init Ramdisk from Legacy Image at 44300000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16044833 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 44000000 Booting using the fdt blob at 0x44000000 Using Device Tree in place at 44000000, end 44008aa1 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.128-cip11 (KernelCI@build-j324968-arm-gcc-10-multi-v7-defconfig-9fkc6) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Thu Jul 7 05:38:02 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Banana Pi BPI-M2-Plus H3 [ 0.000000] earlycon: uart0 at MMIO32 0x01c28000 (options '115200n8') [ 0.000000] printk: bootconsole [uart0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x79800000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x000000006fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000070000000-0x000000007fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x000000007fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000007fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: Using PSCI v0.1 Function IDs from DT [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 933780K/1048576K available (13312K kernel code, 2230K rwdata, 5340K rodata, 2048K init, 425K bss, 49260K reserved, 65536K cma-reserved, 196596K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] GIC: Using split EOI/Deactivate mode <6>[ 0.000000] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns <6>[ 0.000007] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns <6>[ 0.008262] Switching to timer-based delay loop, resolution 41ns <6>[ 0.015108] Console: colour dummy device 80x30 <6>[ 0.019865] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) <6>[ 0.030483] pid_max: default: 32768 minimum: 301 <6>[ 0.035512] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.043093] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.051743] CPU: Testing write buffer coherency: ok <3>[ 0.057220] /cpus/cpu@0 missing clock-frequency property <3>[ 0.062803] /cpus/cpu@1 missing clock-frequency property <3>[ 0.068405] /cpus/cpu@2 missing clock-frequency property <3>[ 0.073984] /cpus/cpu@3 missing clock-frequency property <6>[ 0.079562] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.086069] Setting up static identity map for 0x40300000 - 0x403000ac <6>[ 0.093719] rcu: Hierarchical SRCU implementation. <6>[ 0.100689] EFI services will not be available. <6>[ 0.105781] smp: Bringing up secondary CPUs ... <6>[ 0.121341] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.132235] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.143052] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.143148] smp: Brought up 1 node, 4 CPUs <6>[ 0.165258] SMP: Total of 4 processors activated (192.00 BogoMIPS). <6>[ 0.171776] CPU: All CPU(s) started in HYP mode. <6>[ 0.176654] CPU: Virtualization extensions available. <6>[ 0.182607] devtmpfs: initialized <6>[ 0.191007] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 <6>[ 0.199191] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.209300] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.218557] pinctrl core: initialized pinctrl subsystem <6>[ 0.225582] DMI not present or invalid. <6>[ 0.230530] NET: Registered protocol family 16 <6>[ 0.237102] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.246272] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.246567] cpuidle: using governor menu <6>[ 0.257172] No ATAGs? <6>[ 0.259821] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.268094] hw-breakpoint: maximum watchpoint size is 8 bytes. <6>[ 0.276294] Serial: AMBA PL011 UART driver <6>[ 0.325563] iommu: Default domain type: Translated <6>[ 0.331010] vgaarb: loaded <5>[ 0.334721] SCSI subsystem initialized <6>[ 0.339219] usbcore: registered new interface driver usbfs <6>[ 0.345053] usbcore: registered new interface driver hub <6>[ 0.350653] usbcore: registered new device driver usb <6>[ 0.357075] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.362297] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.371737] PTP clock support registered <6>[ 0.378472] clocksource: Switched to clocksource arch_sys_counter <6>[ 1.254636] NET: Registered protocol family 2 <6>[ 1.259541] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.268288] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 1.276946] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 1.285022] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 1.292541] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 1.299281] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.306199] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.313707] NET: Registered protocol family 1 <6>[ 1.318893] RPC: Registered named UNIX socket transport module. <6>[ 1.325072] RPC: Registered udp transport module. <6>[ 1.330067] RPC: Registered tcp transport module. <6>[ 1.335025] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.341739] PCI: CLS 0 bytes, default 64 <6>[ 1.346385] Trying to unpack rootfs image as initramfs... <6>[ 2.404687] Freeing initrd memory: 15672K <6>[ 2.410018] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available <5>[ 2.419578] Initialise system trusted keyrings <6>[ 2.424618] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 2.437124] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 2.443977] NFS: Registering the id_resolver key type <5>[ 2.449446] Key type id_resolver registered <5>[ 2.453886] Key type id_legacy registered <6>[ 2.458246] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 2.465234] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 2.472929] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 2.478007] Key type asymmetric registered <5>[ 2.482403] Asymmetric key parser 'x509' registered <6>[ 2.487583] bounce: pool size: 64 pages <6>[ 2.491722] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 2.499384] io scheduler mq-deadline registered <6>[ 2.504169] io scheduler kyber registered <3>[ 2.510806] sun4i-usb-phy 1c19400.phy: Couldn't request ID GPIO <6>[ 2.527048] sun8i-h3-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver <6>[ 2.535898] sun8i-h3-r-pinctrl 1f02c00.pinctrl: initialized sunXi PIO driver <6>[ 2.609256] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <4>[ 2.618157] sun8i-h3-pinctrl 1c20800.pinctrl: supply vcc-pa not found, using dummy regulator <6>[ 2.627790] printk: console [ttyS0] disabled <6>[ 2.652523] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 48, base_baud = 1500000) is a U6_16550A <6>[ 2.661801] printk: console [ttyS0] enabled <6>[ 2.661801] printk: console [ttyS0] enabled <6>[ 2.670688] printk: bootconsole [uart0] disabled <6>[ 2.670688] printk: bootconsole [uart0] disabled <4>[ 2.681128] sun8i-h3-pinctrl 1c20800.pinctrl: supply vcc-pg not found, using dummy regulator <6>[ 2.710684] 1c28400.serial: ttyS1 at MMIO 0x1c28400 (irq = 49, base_baud = 1500000) is a U6_16550A <6>[ 2.720097] serial serial0: tty port ttyS1 registered <6>[ 2.727053] SuperH (H)SCI(F) driver initialized <6>[ 2.732728] msm_serial: driver initialized <6>[ 2.737219] STMicroelectronics ASC driver initialized <6>[ 2.743568] STM32 USART driver initialized <6>[ 2.762310] brd: module loaded <6>[ 2.773258] loop: module loaded <6>[ 2.786881] CAN device driver interface <6>[ 2.791864] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 2.798667] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 2.803890] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.810144] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 2.815790] igb: Copyright (c) 2007-2014 Intel Corporation. <4>[ 2.824307] sun8i-h3-pinctrl 1c20800.pinctrl: supply vcc-pd not found, using dummy regulator <6>[ 2.833233] dwmac-sun8i 1c30000.ethernet: IRQ eth_wake_irq not found <6>[ 2.839861] dwmac-sun8i 1c30000.ethernet: IRQ eth_lpi not found <6>[ 2.847330] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 2.855070] usbcore: registered new interface driver pegasus <6>[ 2.861037] usbcore: registered new interface driver asix <6>[ 2.866732] usbcore: registered new interface driver ax88179_178a <6>[ 2.873154] usbcore: registered new interface driver cdc_ether <6>[ 2.879295] usbcore: registered new interface driver smsc75xx <6>[ 2.885334] usbcore: registered new interface driver smsc95xx <6>[ 2.891378] usbcore: registered new interface driver net1080 <6>[ 2.897318] usbcore: registered new interface driver cdc_subset <6>[ 2.903530] usbcore: registered new interface driver zaurus <6>[ 2.909464] usbcore: registered new interface driver cdc_ncm <6>[ 2.917447] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 2.924248] ehci-pci: EHCI PCI platform driver <6>[ 2.929008] ehci-platform: EHCI generic platform driver <6>[ 2.934718] ehci-platform 1c1a000.usb: EHCI Host Controller <6>[ 2.940588] ehci-platform 1c1a000.usb: new USB bus registered, assigned bus number 1 <6>[ 2.948940] ehci-platform 1c1a000.usb: irq 37, io mem 0x01c1a000 <6>[ 2.978479] ehci-platform 1c1a000.usb: USB 2.0 started, EHCI 1.00 <6>[ 2.985602] hub 1-0:1.0: USB hub found <6>[ 2.989703] hub 1-0:1.0: 1 port detected <6>[ 2.994646] ehci-orion: EHCI orion driver <6>[ 2.999181] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.003568] ehci-st: EHCI STMicroelectronics driver <6>[ 3.008844] ehci-exynos: EHCI Exynos driver <6>[ 3.013388] ehci-atmel: EHCI Atmel driver <6>[ 3.017749] tegra-ehci: Tegra EHCI driver <6>[ 3.022169] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.028644] ohci-pci: OHCI PCI platform driver <6>[ 3.033401] ohci-platform: OHCI generic platform driver <6>[ 3.039122] ohci-platform 1c1a400.usb: Generic Platform OHCI controller <6>[ 3.046010] ohci-platform 1c1a400.usb: new USB bus registered, assigned bus number 2 <6>[ 3.054272] ohci-platform 1c1a400.usb: irq 38, io mem 0x01c1a400 <6>[ 3.133239] hub 2-0:1.0: USB hub found <6>[ 3.137287] hub 2-0:1.0: 1 port detected <6>[ 3.142339] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.146837] ohci-st: OHCI STMicroelectronics driver <6>[ 3.152139] ohci-atmel: OHCI Atmel driver <6>[ 3.157121] usbcore: registered new interface driver usb-storage <6>[ 3.167868] sun6i-rtc 1f00000.rtc: registered as rtc0 <6>[ 3.173246] sun6i-rtc 1f00000.rtc: setting system clock to 1970-01-01T00:00:21 UTC (21) <6>[ 3.181533] sun6i-rtc 1f00000.rtc: RTC enabled <6>[ 3.187078] i2c /dev entries driver <6>[ 3.198799] sunxi-wdt 1c20ca0.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0) <4>[ 3.210501] sun8i-h3-r-pinctrl 1f02c00.pinctrl: supply vcc-pl not found, using dummy regulator <6>[ 3.220058] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.226495] sdhci: Copyright(c) Pierre Ossman <6>[ 3.232665] Synopsys Designware Multimedia Card Interface Driver <4>[ 3.240107] sun8i-h3-pinctrl 1c20800.pinctrl: supply vcc-pf not found, using dummy regulator <6>[ 3.240186] sdhci-pltfm: SDHCI platform and OF driver helper <4>[ 3.249950] sun8i-h3-pinctrl 1c20800.pinctrl: supply vcc-pc not found, using dummy regulator <6>[ 3.250093] sunxi-mmc 1c10000.mmc: allocated mmc-pwrseq <6>[ 3.250097] sunxi-mmc 1c0f000.mmc: Got CD GPIO <6>[ 3.274429] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.275401] sunxi-mmc 1c10000.mmc: initialized, max. request size: 16384 KB <6>[ 3.275407] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 16384 KB <6>[ 3.281630] usbcore: registered new interface driver usbhid <6>[ 3.299867] sunxi-mmc 1c11000.mmc: initialized, max. request size: 16384 KB <6>[ 3.302297] usbhid: USB HID core driver <4>[ 3.328732] mmc1: queuing unknown CIS tuple 0x80 (2 bytes) <6>[ 3.329687] NET: Registered protocol family 10 <4>[ 3.336000] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) <6>[ 3.340178] Segment Routing with IPv6 <4>[ 3.346469] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) <6>[ 3.348952] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <4>[ 3.357362] mmc1: queuing unknown CIS tuple 0x80 (7 bytes) <6>[ 3.361406] NET: Registered protocol family 17 <6>[ 3.371292] can: controller area network core <6>[ 3.375962] NET: Registered protocol family 29 <6>[ 3.380679] can: raw protocol <6>[ 3.383908] can: broadcast manager protocol <6>[ 3.387658] mmc2: new DDR MMC card at address 0001 <6>[ 3.388355] can: netlink gateway - max_hops=1 <6>[ 3.394186] mmcblk2: mmc2:0001 8WPD3R 7.28 GiB <5>[ 3.398645] Key type dns_resolver registered <6>[ 3.403237] mmcblk2boot0: mmc2:0001 8WPD3R partition 1 4.00 MiB <6>[ 3.407436] ThumbEE CPU extension supported. <6>[ 3.413936] mmcblk2boot1: mmc2:0001 8WPD3R partition 2 4.00 MiB <5>[ 3.418069] Registering SWP/SWPB emulation handler <6>[ 3.426002] mmcblk2: <5>[ 3.432034] Loading compiled-in X.509 certificates <4>[ 3.448365] sun8i-h3-pinctrl 1c20800.pinctrl: supply vcc-pd not found, using dummy regulator <6>[ 3.454908] mmc1: new high speed SDIO card at address 0001 <6>[ 3.461442] dwmac-sun8i 1c30000.ethernet: IRQ eth_wake_irq not found <6>[ 3.469471] dwmac-sun8i 1c30000.ethernet: IRQ eth_lpi not found <6>[ 3.475939] dwmac-sun8i 1c30000.ethernet: PTP uses main clock <4>[ 3.481985] dwmac-sun8i 1c30000.ethernet: Current syscon value is not the default 50006 (expect 58000) <4>[ 3.498352] mmc0: host does not support reading read-only switch, assuming write-enable <6>[ 3.508652] mmc0: new high speed SDHC card at address 59b4 <6>[ 3.515325] mmcblk0: mmc0:59b4 USDU1 14.9 GiB <6>[ 3.528715] mmcblk0: p1 <6>[ 3.615231] dwmac-sun8i 1c30000.ethernet: No HW DMA feature register supported <6>[ 3.622757] dwmac-sun8i 1c30000.ethernet: RX Checksum Offload Engine supported <6>[ 3.630257] dwmac-sun8i 1c30000.ethernet: COE Type 2 <6>[ 3.635480] dwmac-sun8i 1c30000.ethernet: TX Checksum insertion supported <6>[ 3.642539] dwmac-sun8i 1c30000.ethernet: Normal descriptors <6>[ 3.648469] dwmac-sun8i 1c30000.ethernet: Chain mode enabled <6>[ 3.656310] dwmac-sun8i 1c30000.ethernet: Found internal PHY node <6>[ 3.663236] dwmac-sun8i 1c30000.ethernet: Switch mux to internal PHY <6>[ 3.669889] dwmac-sun8i 1c30000.ethernet: Powering internal PHY <6>[ 3.711213] dwmac-sun8i 1c30000.ethernet: Switch mux to external PHY <6>[ 3.766207] ehci-platform 1c1b000.usb: EHCI Host Controller <6>[ 3.772111] ehci-platform 1c1b000.usb: new USB bus registered, assigned bus number 3 <6>[ 3.780524] ehci-platform 1c1b000.usb: irq 39, io mem 0x01c1b000 <6>[ 3.808493] ehci-platform 1c1b000.usb: USB 2.0 started, EHCI 1.00 <6>[ 3.815781] hub 3-0:1.0: USB hub found <6>[ 3.819873] hub 3-0:1.0: 1 port detected <6>[ 3.827062] ehci-platform 1c1c000.usb: EHCI Host Controller <6>[ 3.834509] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 4 <6>[ 3.842985] ehci-platform 1c1c000.usb: irq 41, io mem 0x01c1c000 <6>[ 3.878489] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 <6>[ 3.885919] hub 4-0:1.0: USB hub found <6>[ 3.890026] hub 4-0:1.0: 1 port detected <6>[ 3.897713] ohci-platform 1c1b400.usb: Generic Platform OHCI controller <6>[ 3.905087] ohci-platform 1c1b400.usb: new USB bus registered, assigned bus number 5 <6>[ 3.913307] ohci-platform 1c1b400.usb: irq 40, io mem 0x01c1b400 <6>[ 3.993609] hub 5-0:1.0: USB hub found <6>[ 3.997684] hub 5-0:1.0: 1 port detected <6>[ 4.005417] ohci-platform 1c1c400.usb: Generic Platform OHCI controller <6>[ 4.013903] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 6 <6>[ 4.022361] ohci-platform 1c1c400.usb: irq 42, io mem 0x01c1c400 <6>[ 4.103249] hub 6-0:1.0: USB hub found <6>[ 4.107298] hub 6-0:1.0: 1 port detected <6>[ 4.112846] input: gpio_keys as /devices/platform/gpio_keys/input/input0 <6>[ 4.121907] dwmac-sun8i 1c30000.ethernet eth0: PHY [0.2:01] driver [RTL8211E Gigabit Ethernet] (irq=POLL) <6>[ 4.132994] dwmac-sun8i 1c30000.ethernet eth0: No Safety Features support found <6>[ 4.140590] dwmac-sun8i 1c30000.ethernet eth0: No MAC Management Counters available <4>[ 4.148519] dwmac-sun8i 1c30000.ethernet eth0: PTP not supported by HW <6>[ 4.155766] dwmac-sun8i 1c30000.ethernet eth0: configuring for phy/rgmii-id link mode <6>[ 8.299392] dwmac-sun8i 1c30000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx <6>[ 8.335522] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 8.358500] Sending DHCP requests ., OK <6>[ 8.410270] IP-Config: Got DHCP answer from 10.201.1.3, my address is 10.201.3.139 <6>[ 8.419156] IP-Config: Complete: <6>[ 8.423211] device=eth0, hwaddr=02:81:36:39:14:1c, ipaddr=10.201.3.139, mask=255.255.0.0, gw=10.201.1.3 <6>[ 8.434425] host=10.201.3.139, domain=, nis-domain=(none) <6>[ 8.441553] bootserver=10.201.1.3, rootserver=10.201.1.3, rootpath= <6>[ 8.441751] nameserver0=10.1.1.1 <6>[ 8.474920] Freeing unused kernel memory: 2048K <6>[ 8.518894] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 8.654926] udevd[118]: starting version 3.2.9 <5>[ 8.665662] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.672715] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.685903] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 8.700732] udevd[118]: specified user 'tss' unknown <27>[ 8.706197] udevd[118]: specified group 'tss' unknown <30>[ 8.714345] udevd[119]: starting eudev-3.2.9 <4>[ 9.263632] usb_phy_generic usb_phy_generic.1.auto: supply vcc not found, using dummy regulator <4>[ 9.272927] usb_phy_generic usb_phy_generic.1.auto: dummy supplies not allowed for exclusive requests <6>[ 9.286163] musb-hdrc musb-hdrc.2.auto: MUSB HDRC host driver <6>[ 9.292282] musb-hdrc musb-hdrc.2.auto: new USB bus registered, assigned bus number 7 <5>[ 9.308085] cfg80211: Loading compiled-in X.509 certificates for regulatory database <6>[ 9.389874] lima 1c40000.gpu: gp - mali400 version major 1 minor 1 <6>[ 9.396450] lima 1c40000.gpu: pp0 - mali400 version major 1 minor 1 <6>[ 9.403202] lima 1c40000.gpu: pp1 - mali400 version major 1 minor 1 <6>[ 9.409844] lima 1c40000.gpu: l2 cache 64K, 4-way, 64byte cache line, 64bit external bus <6>[ 9.473755] Bluetooth: Core ver 2.22 <6>[ 9.477704] NET: Registered protocol family 31 <6>[ 9.482546] Bluetooth: HCI device and connection manager initialized <6>[ 9.489250] Bluetooth: HCI socket layer initialized <6>[ 9.493258] lima 1c40000.gpu: bus rate = 200000000 <6>[ 9.493393] hub 7-0:1.0: USB hub found <6>[ 9.493445] hub 7-0:1.0: 1 port detected <6>[ 9.494407] Bluetooth: L2CAP socket layer initialized <6>[ 9.499532] lima 1c40000.gpu: mod rate = 297000000 <6>[ 9.503545] Bluetooth: SCO socket layer initialized <3>[ 9.507790] lima 1c40000.gpu: dev_pm_opp_set_regulators: no regulator (mali) found: -19 <6>[ 9.518603] Bluetooth: HCI UART driver ver 2.3 <6>[ 9.536371] Bluetooth: HCI UART protocol H4 registered <6>[ 9.547505] Bluetooth: HCI UART protocol Broadcom registered <5>[ 9.584965] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' <4>[ 9.592313] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 <6>[ 9.601273] cfg80211: failed to load regulatory.db <6>[ 9.791211] [drm] Initialized lima 1.1.0 20191231 for 1c40000.gpu on minor 0 <6>[ 9.811362] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43430a0-sdio for chip BCM43430/0 <4>[ 9.834554] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac43430a0-sdio.bin failed with error -2 done Saving random seed: <5>[ 9.906889] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: <6>[ 9.933478] Bluetooth: hci0: BCM: chip id 94 <6>[ 9.940597] Bluetooth: hci0: BCM: features 0x2e ip: RTNETLINK answers: File exists FAIL <6>[ 9.976142] Bluetooth: hci0: 4343A0 <6>[ 9.980034] Bluetooth: hci0: BCM4343A0 (001.001.034) build 0000 <3>[ 9.986414] Bluetooth: hci0: BCM: firmware Patch file not found, tried: <3>[ 9.994862] Bluetooth: hci0: BCM: 'brcm/BCM4343A0.hcd' <3>[ 10.000692] Bluetooth: hci0: BCM: 'brcm/BCM.hcd' Starting dropbear sshd: <5>[ 10.020014] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-2190477/environment . /lava-2190477/environment / # /lava-2190477/bin/lava-test-runner /lava-2190477/0 /lava-2190477/bin/lava-test-runner /lava-2190477/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-2190477/0/tests/0_dmesg + cat uuid <8>[ 10.633878] + UUID=2190477_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 10.678152] <8>[ 10.735742] <8>[ 10.776748] + set +x <8>[ 10.786895] / # # export SHELL=/bin/sh <3>[ 10.856344] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000): clkctl 0x50 # / # export SHELL=/bin/sh. /lava-2190477/environment / # . /lava-2190477/environment/lava-2190477/bin/lava-test-runner /lava-2190477/1 / # /lava-2190477/bin/lava-test-runner /lava-2190477/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-2190477/1/tests/1_bootrr + cat uuid <8>[ 11.293201] + UUID=2190477_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/helpers:/lava-2190477/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr + sh helpers/bootrr-auto /lava-2190477/1/../bin/lava-test-case <8>[ 12.339905] /lava-2190477/1/../bin/lava-test-case <8>[ 12.387954] /lava-2190477/1/../bin/lava-test-case <8>[ 12.412841] + set +x <8>[ 12.431854] / #