Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. U-Boot SPL 2020.10-dirty (Dec 20 2020 - 09:44:17 +0100) DRAM: 2048 MiB Trying to boot from MMC1 NOTICE: BL31: v2.3(release):v2.3-797-g7ad39818b-dirty NOTICE: BL31: Built : 10:18:27, Oct 21 2020 NOTICE: BL31: Detected Allwinner H6 SoC (1728) NOTICE: BL31: Found U-Boot DTB at 0xc0887e0, model: Pine H64 NOTICE: PMIC: Probing AXP805 on I2C NOTICE: axp_check_id ret=96 NOTICE: Check aldo1 NOTICE: Enable aldo1 NOTICE: PMIC: aldo1 voltage: 3.300V NOTICE: Check aldo2 NOTICE: Enable aldo2 NOTICE: PMIC: aldo2 voltage: 3.300V NOTICE: Check aldo3 NOTICE: Enable aldo3 NOTICE: PMIC: aldo3 voltage: 3.300V NOTICE: Check bldo1 NOTICE: Enable bldo1 NOTICE: PMIC: bldo1 voltage: 1.800V NOTICE: Check bldo2 NOTICE: Enable bldo2 NOTICE: PMIC: bldo2 voltage: 1.800V NOTICE: Check bldo3 NOTICE: Enable bldo3 NOTICE: PMIC: bldo3 voltage: 1.800V NOTICE: Check bldo4 NOTICE: Check cldo1 NOTICE: Enable cldo1 NOTICE: PMIC: cldo1 voltage: 3.300V NOTICE: Check cldo2 NOTICE: Enable cldo2 NOTICE: PMIC: cldo2 voltage: 3.300V NOTICE: Check cldo3 NOTICE: Enable cldo3 NOTICE: PMIC: cldo3 voltage: 3.300V NOTICE: Check dcdca NOTICE: Enable dcdca NOTICE: Check dcdcc NOTICE: Enable dcdcc NOTICE: Check dcdcd NOTICE: Enable dcdcd NOTICE: PMIC: dcdcd voltage: 0.960V NOTICE: Check dcdce NOTICE: Enable dcdce NOTICE: PMIC: dcdce voltage: 1.200V NOTICE: Check sw NOTICE: BL31: Platform setup done NOTICE: PSCI: System suspend is unavailable U-Boot 2020.10-dirty (Dec 20 2020 - 09:44:17 +0100) Allwinner Technology CPU: Allwinner H6 (SUN50I) Model: Pine H64 DRAM: 2 GiB board_init configure MACPWR -22 MMC: mmc@4020000: 0, mmc@4022000: 1 Loading Environment from FAT... Unable to use mmc 1:0... In: serial@5000000 Out: serial@5000000 Err: serial@5000000 Net: phy interface7 eth0: ethernet@5020000 starting USB... Bus usb@5101000: USB EHCI 1.00 Bus usb@5101400: USB OHCI 1.0 Bus usb@5311000: USB EHCI 1.00 Bus usb@5311400: USB OHCI 1.0 scanning bus usb@5101000 for devices... 1 USB Device(s) found scanning bus usb@5101400 for devices... 1 USB Device(s) found scanning bus usb@5311000 for devices... 2 USB Device(s) found scanning bus usb@5311400 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp ethernet@5020000 Waiting for PHY auto negotiation to complete........ done BOOTP broadcast 1 BOOTP broadcast 2 DHCP client bound to address 10.201.3.61 (260 ms) => setenv serverip 10.201.1.11 setenv serverip 10.201.1.11 => tftp 0x40080000 2190391/tftp-deploy-b7jb49ha/kernel/Image tftp 0x40080000 2190391/tftp-deploy-b7jb49ha/kernel/Image Using ethernet@5020000 device TFTP from server 10.201.1.11; our IP address is 10.201.3.61 Filename '2190391/tftp-deploy-b7jb49ha/kernel/Image'. Load address: 0x40080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# #################### 8 MiB/s done Bytes transferred = 31773184 (1e4d200 hex) => tftp 0x4FF00000 2190391/tftp-deploy-b7jb49ha/ramdisk/ramdisk.cpio.gz.uboot tftp 0x4FF00000 2190391/tftp-deploy-b7jb49ha/ramdisk/ramdisk.cpio.gz.uboot Using ethernet@5020000 device TFTP from server 10.201.1.11; our IP address is 10.201.3.61 Filename '2190391/tftp-deploy-b7jb49ha/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x4ff00000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ##########################################################T ###T #### ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ###################################################### 1.5 MiB/s done Bytes transferred = 18913011 (12096f3 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x4FA00000 2190391/tftp-deploy-b7jb49ha/dtb/sun50i-h6-pine-h64.dtb tftp 0x4FA00000 2190391/tftp-deploy-b7jb49ha/dtb/sun50i-h6-pine-h64.dtb Using ethernet@5020000 device TFTP from server 10.201.1.11; our IP address is 10.201.3.61 Filename '2190391/tftp-deploy-b7jb49ha/dtb/sun50i-h6-pine-h64.dtb'. Load address: 0x4fa00000 Loading: *## 4.4 MiB/s done Bytes transferred = 23057 (5a11 hex) => setenv bootargs 'console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => booti 0x40080000 0x4FF00000 0x4FA00000 booti 0x40080000 0x4FF00000 0x4FA00000 Moving Image from 0x40080000 to 0x40200000, end=420e0000 ## Loading init Ramdisk from Legacy Image at 4ff00000 ... Image Name: Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 18912947 Bytes = 18 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 4fa00000 Booting using the fdt blob at 0x4fa00000 EHCI failed to shut down host controller. Loading Device Tree to 0000000049ff7000, end 0000000049fffa10 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 5.10.128-cip11 (KernelCI@build-j325037-arm64-gcc-10-defconfig-p6t8f) (aarch64-linux-gnu-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP PREEMPT Thu Jul 7 05:28:48 UTC 2022 [ 0.000000] Machine model: Pine H64 model A [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: uart0 at MMIO32 0x0000000005000000 (options '115200n8') [ 0.000000] printk: bootconsole [uart0] enabled [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] NUMA: NODE_DATA [mem 0xbfbdeb00-0xbfbe0fff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] cma: Reserved 32 MiB at 0x00000000bb000000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 23 pages/cpu s56600 r8192 d29416 u94208 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: ARM erratum 845719 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 516096 [ 0.000000] Policy zone: DMA [ 0.000000] Kernel command line: console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 1973824K/2097152K available (14592K kernel code, 2804K rwdata, 7592K rodata, 5952K init, 514K bss, 90560K reserved, 32768K cma-reserved) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] GIC: Using split EOI/Deactivate mode <6>[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns <6>[ 0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns <6>[ 0.010056] Console: colour dummy device 80x25 <6>[ 0.015293] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) <6>[ 0.026854] pid_max: default: 32768 minimum: 301 <6>[ 0.032296] LSM: Security Framework initializing <6>[ 0.037716] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 0.046133] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 0.056677] rcu: Hierarchical SRCU implementation. <6>[ 0.064285] EFI services will not be available. <6>[ 0.069824] smp: Bringing up secondary CPUs ... <6>[ 0.075744] Detected VIPT I-cache on CPU1 <6>[ 0.075813] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] <6>[ 0.076427] Detected VIPT I-cache on CPU2 <6>[ 0.076468] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] <6>[ 0.077038] Detected VIPT I-cache on CPU3 <6>[ 0.077074] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] <6>[ 0.077149] smp: Brought up 1 node, 4 CPUs <6>[ 0.118343] SMP: Total of 4 processors activated. <6>[ 0.123796] CPU features: detected: 32-bit EL0 Support <6>[ 0.129743] CPU features: detected: CRC32 instructions <6>[ 0.135675] CPU features: detected: 32-bit EL1 Support <6>[ 0.150470] CPU: All CPU(s) started at EL2 <6>[ 0.155288] alternatives: patching kernel code <6>[ 0.162181] devtmpfs: initialized <4>[ 0.170888] KASLR disabled due to lack of seed <6>[ 0.176244] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.187238] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.196342] pinctrl core: initialized pinctrl subsystem <6>[ 0.203723] DMI not present or invalid. <6>[ 0.208987] NET: Registered protocol family 16 <6>[ 0.215928] DMA: preallocated 256 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.224096] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.233076] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations <6>[ 0.242137] audit: initializing netlink subsys (disabled) <5>[ 0.248524] audit: type=2000 audit(0.164:1): state=initialized audit_enabled=0 res=1 <6>[ 0.249673] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.257321] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.264540] cpuidle: using governor menu <6>[ 0.276784] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.284616] ASID allocator initialised with 65536 entries <6>[ 0.292326] Serial: AMBA PL011 UART driver <6>[ 0.330232] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.337917] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.345561] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.353195] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.362077] cryptd: max_cpu_qlen set to 1000 <6>[ 0.369519] ACPI: Interpreter disabled. <6>[ 0.375867] iommu: Default domain type: Translated <6>[ 0.381757] vgaarb: loaded <5>[ 0.385329] SCSI subsystem initialized <6>[ 0.390117] usbcore: registered new interface driver usbfs <6>[ 0.396475] usbcore: registered new interface driver hub <6>[ 0.402629] usbcore: registered new device driver usb <6>[ 0.409135] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.414873] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.425196] PTP clock support registered <6>[ 0.429908] EDAC MC: Ver: 3.0.0 <6>[ 0.434909] FPGA manager framework <6>[ 0.439022] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.446859] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.454063] VFS: Disk quotas dquot_6.6.0 <6>[ 0.458713] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 0.466767] pnp: PnP ACPI: disabled <6>[ 0.477555] NET: Registered protocol family 2 <6>[ 0.482835] IP idents hash table entries: 32768 (order: 6, 262144 bytes, linear) <6>[ 0.492385] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes, linear) <6>[ 0.502111] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 0.511232] TCP bind hash table entries: 16384 (order: 6, 262144 bytes, linear) <6>[ 0.519840] TCP: Hash tables configured (established 16384 bind 16384) <6>[ 0.527416] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear) <6>[ 0.535113] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, linear) <6>[ 0.543401] NET: Registered protocol family 1 <6>[ 0.548896] RPC: Registered named UNIX socket transport module. <6>[ 0.555700] RPC: Registered udp transport module. <6>[ 0.561179] RPC: Registered tcp transport module. <6>[ 0.566634] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.574000] PCI: CLS 0 bytes, default 64 <6>[ 0.578776] Unpacking initramfs... <6>[ 1.659035] Freeing initrd memory: 18464K <6>[ 1.664692] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available <6>[ 1.674329] kvm [1]: IPA Size Limit: 40 bits <6>[ 1.680794] kvm [1]: vgic interrupt IRQ9 <6>[ 1.685530] kvm [1]: Hyp mode initialized successfully <5>[ 1.695641] Initialise system trusted keyrings <6>[ 1.700984] workingset: timestamp_bits=42 max_order=19 bucket_order=0 <6>[ 1.715279] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.722708] NFS: Registering the id_resolver key type <5>[ 1.728599] Key type id_resolver registered <5>[ 1.733480] Key type id_legacy registered <6>[ 1.738262] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 1.745915] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 1.754504] 9p: Installing v9fs 9p2000 file system support <5>[ 1.806536] Key type asymmetric registered <5>[ 1.811326] Asymmetric key parser 'x509' registered <6>[ 1.817003] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 1.825412] io scheduler mq-deadline registered <6>[ 1.830671] io scheduler kyber registered <3>[ 1.837196] sun50i-de2-bus 1000000.bus: Error couldn't map SRAM to device <3>[ 1.845769] sun4i-usb-phy 5100400.phy: Couldn't get regulator usb0_vbus... Deferring probe <6>[ 1.863312] sun50i-h6-r-pinctrl 7022000.pinctrl: initialized sunXi PIO driver <4>[ 1.875460] EINJ: ACPI disabled. <6>[ 1.897054] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 1.906927] SuperH (H)SCI(F) driver initialized <6>[ 1.912832] msm_serial: driver initialized <4>[ 1.919153] cacheinfo: Unable to detect cache hierarchy for CPU 0 <6>[ 1.933465] loop: module loaded <6>[ 1.938203] megasas: 07.714.04.00-rc1 <6>[ 1.948534] tun: Universal TUN/TAP device driver, 1.6 <6>[ 1.955258] thunder_xcv, ver 1.0 <6>[ 1.959135] thunder_bgx, ver 1.0 <6>[ 1.962999] nicpf, ver 1.0 <6>[ 1.967492] hclge is initializing <6>[ 1.971441] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 1.979656] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 1.985819] e1000: Intel(R) PRO/1000 Network Driver <6>[ 1.991462] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 1.998094] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 2.003830] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.010659] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 2.016873] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 2.023309] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 2.030475] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 2.037595] sky2: driver version 1.30 <6>[ 2.043062] VFIO - User Level meta-driver version: 0.3 <6>[ 2.050947] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 2.058407] ehci-pci: EHCI PCI platform driver <6>[ 2.063610] ehci-platform: EHCI generic platform driver <6>[ 2.070065] ehci-orion: EHCI orion driver <6>[ 2.074874] ehci-exynos: EHCI Exynos driver <6>[ 2.079848] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 2.086966] ohci-pci: OHCI PCI platform driver <6>[ 2.092171] ohci-platform: OHCI generic platform driver <6>[ 2.098512] ohci-exynos: OHCI Exynos driver <6>[ 2.103946] usbcore: registered new interface driver usb-storage <6>[ 2.114161] sun6i-rtc 7000000.rtc: registered as rtc0 <6>[ 2.120036] sun6i-rtc 7000000.rtc: setting system clock to 1970-01-01T00:00:26 UTC (26) <6>[ 2.129113] sun6i-rtc 7000000.rtc: RTC enabled <6>[ 2.134611] i2c /dev entries driver <4>[ 2.139359] sun50i-h6-r-pinctrl 7022000.pinctrl: supply vcc-pl not found, using dummy regulator <6>[ 2.150736] axp20x-i2c 0-0036: AXP20x variant AXP806 found <6>[ 2.162478] vdd-cpu: supplied by regulator-dummy <6>[ 2.169093] vdd-gpu: supplied by regulator-dummy <6>[ 2.174967] vdd-sys: supplied by regulator-dummy <6>[ 2.180957] vcc-dram: supplied by regulator-dummy <6>[ 2.187017] vcc-pl: supplied by regulator-dummy <6>[ 2.193010] vcc-ac200: supplied by regulator-dummy <6>[ 2.199064] vcc-3v3-1: supplied by regulator-dummy <6>[ 2.205217] vcc-bias-pll: supplied by regulator-dummy <6>[ 2.212096] vcc-efuse-pcie-hdmi-io: supplied by regulator-dummy <6>[ 2.219500] vcc-dcxoio: supplied by regulator-dummy <6>[ 2.225861] bldo4: supplied by regulator-dummy <6>[ 2.231550] vcc-3v3-2: supplied by regulator-dummy <6>[ 2.237816] vcc-wifi-1: supplied by regulator-dummy <6>[ 2.244095] vcc-wifi-2: supplied by regulator-dummy <6>[ 2.249924] sw: supplied by regulator-dummy <6>[ 2.254884] axp20x-i2c 0-0036: AXP20X driver loaded <6>[ 2.267435] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.274535] sdhci: Copyright(c) Pierre Ossman <6>[ 2.280144] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.288165] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.296836] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 2.304493] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping .... <6>[ 2.312611] usbcore: registered new interface driver usbhid <6>[ 2.319021] usbhid: USB HID core driver <6>[ 2.329250] NET: Registered protocol family 17 <6>[ 2.334600] 9pnet: Installing 9P2000 support <5>[ 2.339642] Key type dns_resolver registered <6>[ 2.344959] registered taskstats version 1 <5>[ 2.349752] Loading compiled-in X.509 certificates <6>[ 2.378623] sun50i-h6-pinctrl 300b000.pinctrl: initialized sunXi PIO driver <4>[ 2.387994] sun50i-h6-pinctrl 300b000.pinctrl: supply vcc-ph not found, using dummy regulator <6>[ 2.398221] printk: console [ttyS0] disabled <6>[ 2.423668] 5000000.serial: ttyS0 at MMIO 0x5000000 (irq = 33, base_baud = 1500000) is a 16550A <6>[ 2.433547] printk: console [ttyS0] enabled <6>[ 2.433547] printk: console [ttyS0] enabled <6>[ 2.442863] printk: bootconsole [uart0] disabled <6>[ 2.442863] printk: bootconsole [uart0] disabled <6>[ 2.562902] ehci-platform 5101000.usb: EHCI Host Controller <6>[ 2.568772] ehci-platform 5101000.usb: new USB bus registered, assigned bus number 1 <6>[ 2.576900] ehci-platform 5101000.usb: irq 36, io mem 0x05101000 <6>[ 2.598871] ehci-platform 5101000.usb: USB 2.0 started, EHCI 1.00 <6>[ 2.605850] hub 1-0:1.0: USB hub found <6>[ 2.609895] hub 1-0:1.0: 1 port detected <6>[ 2.616226] ehci-platform 5311000.usb: EHCI Host Controller <6>[ 2.622090] ehci-platform 5311000.usb: new USB bus registered, assigned bus number 2 <6>[ 2.630204] ehci-platform 5311000.usb: irq 38, io mem 0x05311000 <6>[ 2.650876] ehci-platform 5311000.usb: USB 2.0 started, EHCI 1.00 <6>[ 2.657818] hub 2-0:1.0: USB hub found <6>[ 2.661864] hub 2-0:1.0: 1 port detected <6>[ 2.783024] ohci-platform 5101400.usb: Generic Platform OHCI controller <6>[ 2.789931] ohci-platform 5101400.usb: new USB bus registered, assigned bus number 3 <6>[ 2.798077] ohci-platform 5101400.usb: irq 37, io mem 0x05101400 <6>[ 2.867451] hub 3-0:1.0: USB hub found <6>[ 2.871502] hub 3-0:1.0: 1 port detected <6>[ 2.877815] ohci-platform 5311400.usb: Generic Platform OHCI controller <6>[ 2.884742] ohci-platform 5311400.usb: new USB bus registered, assigned bus number 4 <6>[ 2.892876] ohci-platform 5311400.usb: irq 39, io mem 0x05311400 <6>[ 2.918873] usb 2-1: new high-speed USB device number 2 using ehci-platform <6>[ 2.963460] hub 4-0:1.0: USB hub found <6>[ 2.967506] hub 4-0:1.0: 1 port detected <4>[ 2.974006] usb_phy_generic usb_phy_generic.1.auto: supply vcc not found, using dummy regulator <4>[ 2.983145] usb_phy_generic usb_phy_generic.1.auto: dummy supplies not allowed for exclusive requests <6>[ 3.011125] musb-hdrc musb-hdrc.2.auto: MUSB HDRC host driver <6>[ 3.017161] musb-hdrc musb-hdrc.2.auto: new USB bus registered, assigned bus number 5 <6>[ 3.025852] hub 5-0:1.0: USB hub found <6>[ 3.029896] hub 5-0:1.0: 1 port detected <4>[ 3.041389] sun50i-h6-pinctrl 300b000.pinctrl: supply vcc-pf not found, using dummy regulator <6>[ 3.050922] sunxi-mmc 4020000.mmc: Got CD GPIO <6>[ 3.069348] sunxi-mmc 4022000.mmc: initialized, max. request size: 2048 KB, uses new timings mode <6>[ 3.081066] sunxi-mmc 4020000.mmc: initialized, max. request size: 16384 KB, uses new timings mode <4>[ 3.124917] mmc1: host does not support reading read-only switch, assuming write-enable <4>[ 3.134944] mmc1: Problem switching card into high-speed mode! <6>[ 3.141203] mmc1: new SDHC card at address 0001 <6>[ 3.146718] mmcblk1: mmc1:0001 SD16G 7.38 GiB <6>[ 3.183329] mmc0: new DDR MMC card at address 0001 <6>[ 3.189077] mmcblk0: mmc0:0001 DA4032 29.1 GiB <6>[ 3.194196] mmcblk0boot0: mmc0:0001 DA4032 partition 1 4.00 MiB <6>[ 3.200698] mmcblk0boot1: mmc0:0001 DA4032 partition 2 4.00 MiB <6>[ 15.383024] ALSA device list: <6>[ 15.386264] No soundcards found. <6>[ 15.393263] Freeing unused kernel memory: 5952K <6>[ 15.398223] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 15.472538] udevd[167]: starting version 3.2.9 <5>[ 15.478142] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 15.485047] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 15.491805] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 15.504029] udevd[167]: specified user 'tss' unknown <27>[ 15.509452] udevd[167]: specified group 'tss' unknown <30>[ 15.516444] udevd[168]: starting eudev-3.2.9 <6>[ 15.804832] sun8i-ce 1904000.crypto: Set mod clock to 300000000 (300 Mhz) from 24000000 (24 Mhz) <6>[ 15.818676] panfrost 1800000.gpu: clock rate = 432000000 <6>[ 15.834987] panfrost 1800000.gpu: bus_clock rate = 100000000 <6>[ 15.855557] panfrost 1800000.gpu: mali-t720 id 0x720 major 0x1 minor 0x1 status 0x0 <6>[ 15.867244] sun8i-ce 1904000.crypto: will run requests pump with realtime priority <6>[ 15.882988] panfrost 1800000.gpu: features: 00000000,10309e40, issues: 00000000,21054400 <4>[ 15.908103] sun8i-mixer 1100000.mixer: deferred probe timeout, ignoring dependency <6>[ 15.916095] sun8i-ce 1904000.crypto: will run requests pump with realtime priority <6>[ 15.933986] panfrost 1800000.gpu: Features: L2:0x07110206 Shader:0x00000000 Tiler:0x00000809 Mem:0x1 MMU:0x00002821 AS:0xf JS:0x7 <6>[ 15.942936] sun8i-ce 1904000.crypto: will run requests pump with realtime priority <6>[ 15.958660] panfrost 1800000.gpu: shader_present=0x3 l2_present=0x1 <6>[ 15.967636] dwmac-sun8i 5020000.ethernet: IRQ eth_wake_irq not found <6>[ 15.975887] sun8i-ce 1904000.crypto: will run requests pump with realtime priority <6>[ 15.984270] sun8i-ce 1904000.crypto: Register cbc(aes) <4>[ 15.984881] sun4i-drm display-engine: deferred probe timeout, ignoring dependency <6>[ 15.990550] sun8i-ce 1904000.crypto: Register ecb(aes) <6>[ 15.995035] dwmac-sun8i 5020000.ethernet: IRQ eth_lpi not found <6>[ 15.995433] dwmac-sun8i 5020000.ethernet: PTP uses main clock <4>[ 15.995458] dwmac-sun8i 5020000.ethernet: Current syscon value is not the default 50846 (expect 50000) <6>[ 15.998451] sunxi-wdt 7020400.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0) <6>[ 16.013382] [drm] Initialized panfrost 1.1.0 20180908 for 1800000.gpu on minor 0 <6>[ 16.040861] sun8i-ce 1904000.crypto: Register cbc(des3_ede) <6>[ 16.041336] Registered IR keymap rc-empty <6>[ 16.041914] sun4i-drm display-engine: bound 1100000.mixer (ops sun8i_mixer_ops [sun8i_mixer]) <6>[ 16.042162] sun4i-drm display-engine: bound 6510000.tcon-top (ops sun8i_tcon_top_ops [sun8i_tcon_top]) <6>[ 16.042451] sun4i-drm display-engine: bound 6515000.lcd-controller (ops sun4i_tcon_ops [sun4i_tcon]) <4>[ 16.042530] sun8i-dw-hdmi 6000000.hdmi: supply hvcc not found, using dummy regulator <3>[ 16.042809] sun8i-dw-hdmi 6000000.hdmi: Couldn't get the HDMI PHY <3>[ 16.043853] sun4i-drm display-engine: Couldn't bind all pipelines components <4>[ 16.046234] sun4i-drm display-engine: deferred probe timeout, ignoring dependency <6>[ 16.047605] sun4i-drm display-engine: bound 1100000.mixer (ops sun8i_mixer_ops [sun8i_mixer]) <6>[ 16.052709] rc rc0: sunxi-ir as /devices/platform/soc/7040000.ir/rc/rc0 <6>[ 16.062625] sun4i-drm display-engine: bound 6510000.tcon-top (ops sun8i_tcon_top_ops [sun8i_tcon_top]) <6>[ 16.069896] sun8i-ce 1904000.crypto: Register ecb(des3_ede) <6>[ 16.070063] input: sunxi-ir as /devices/platform/soc/7040000.ir/rc/rc0/input0 <6>[ 16.079287] sun4i-drm display-engine: bound 6515000.lcd-controller (ops sun4i_tcon_ops [sun4i_tcon]) <6>[ 16.087544] sun8i-ce 1904000.crypto: CryptoEngine Die ID 0 <6>[ 16.094411] sunxi-ir 7040000.ir: initialized sunXi IR driver <4>[ 16.094606] sun8i-dw-hdmi 6000000.hdmi: supply hvcc not found, using dummy regulator <6>[ 16.095190] sun8i-dw-hdmi 6000000.hdmi: Detected HDMI TX controller v2.12a with HDCP (DWC HDMI 2.0 TX PHY) <6>[ 16.103408] sun8i-dw-hdmi 6000000.hdmi: registered DesignWare HDMI I2C bus driver <6>[ 16.145911] dwmac-sun8i 5020000.ethernet: No HW DMA feature register supported <6>[ 16.149559] sun4i-drm display-engine: bound 6000000.hdmi (ops sun8i_dw_hdmi_ops [sun8i_drm_hdmi]) <6>[ 16.156639] dwmac-sun8i 5020000.ethernet: RX Checksum Offload Engine supported <6>[ 16.163068] [drm] Initialized sun4i-drm 1.0.0 20150629 for display-engine on minor 1 <6>[ 16.168901] dwmac-sun8i 5020000.ethernet: COE Type 2 <6>[ 16.176555] sun4i-drm display-engine: [drm] Cannot find any crtc or sizes <6>[ 16.186300] dwmac-sun8i 5020000.ethernet: TX Checksum insertion supported <6>[ 16.186314] dwmac-sun8i 5020000.ethernet: Normal descriptors <6>[ 16.194523] sun4i-drm display-engine: [drm] Cannot find any crtc or sizes <6>[ 16.201610] dwmac-sun8i 5020000.ethernet: Chain mode enabled <6>[ 16.426521] ax88179_178a 2-1:1.0 eth1: register 'ax88179_178a' at usb-5311000.usb-1, ASIX AX88179 USB 3.0 Gigabit Ethernet, 00:0e:c6:ac:f3:d0 <6>[ 16.439628] usbcore: registered new interface driver ax88179_178a done Saving random seed: OK Starting network: OK Starting dropbear sshd: <5>[ 16.522131] random: dropbear: uninitialized urandom read (32 bytes read) <6>[ 16.559482] NET: Registered protocol family 10 <6>[ 16.565335] Segment Routing with IPv6 OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-2190391/environment . /lava-2190391/environment / # /lava-2190391/bin/lava-test-runner /lava-2190391/0 /lava-2190391/bin/lava-test-runner /lava-2190391/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-2190391/<8>[ 17.135266] 0/tests/0_dmesg + cat uuid + UUID=2190391_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 17.164353] <8>[ 17.192935] <8>[ 17.221702] + set +x <8>[ 17.231550] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-2190391/environment / # . /lava-2190391/environment/lava-2190391/bin/lava-test-runner /lava-2190391/1 / # /lava-2190391/bin/lava-test-runner /lava-2190391/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-2190391<8>[ 17.702295] /1/tests/1_bootrr + cat uuid + UUID=2190391_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/helpers:/lava-2190391/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr + sh helpers/bootrr-auto /lava-2190391/1/../bin/lava-test-case <8>[ 18.730561] /lava-2190391/1/../bin/lava-test-case <8>[ 18.757263] /lava-2190391/1/../bin/lava-test-case <8>[ 18.775038] + set +x <8>[ 18.789652] / #