Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. ser2net port 3028 device /dev/ttyimx6qp-sabresd-1 [115200 N81] (Debian GNU/Linux) U-Boot 2017.03 (Jan 20 2018 - 10:43:25 +0800) CPU: Freescale i.MX6QP rev1.0 996 MHz (running at 792 MHz) CPU: Automotive temperature grade (-40C to 125C) at 22C Reset cause: POR Model: Freescale i.MX6 Quad Plus SABRE Smart Device Board Board: MX6-SabreSD DRAM: 1 GiB PMIC: PFUZE100! DEV_ID=0x10 REV_ID=0x21 MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 *** Warning - bad CRC, using default environment No panel detected: default to Hannstar-XGA Display: Hannstar-XGA (1024x768) In: serial Out: serial Err: serial flash target is MMC:1 Net: Warning: ethernet@02188000 using MAC address from ROM eth0: ethernet@02188000 [PRIME] Fastboot: Normal Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.1.241 (1255 ms) => setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 => tftp 0x12000000 1014354/tftp-deploy-fmfmjbsl/kernel/zImage tftp 0x12000000 1014354/tftp-deploy-fmfmjbsl/kernel/zImage Using ethernet@02188000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.241; sending through gateway 172.16.1.4 Filename '1014354/tftp-deploy-fmfmjbsl/kernel/zImage'. Load address: 0x12000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ## 10 MiB/s done Bytes transferred = 10514592 (a070a0 hex) => tftp 0x12C00000 1014354/tftp-deploy-fmfmjbsl/ramdisk/ramdisk.cpio.gz.uboot tftp 0x12C00000 1014354/tftp-deploy-fmfmjbsl/ramdisk/ramdisk.cpio.gz.uboot Using ethernet@02188000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.241; sending through gateway 172.16.1.4 Filename '1014354/tftp-deploy-fmfmjbsl/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x12c00000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################ 9.9 MiB/s done Bytes transferred = 10175628 (9b448c hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x18000000 1014354/tftp-deploy-fmfmjbsl/dtb/imx6qp-sabresd.dtb tftp 0x18000000 1014354/tftp-deploy-fmfmjbsl/dtb/imx6qp-sabresd.dtb Using ethernet@02188000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.241; sending through gateway 172.16.1.4 Filename '1014354/tftp-deploy-fmfmjbsl/dtb/imx6qp-sabresd.dtb'. Load address: 0x18000000 Loading: *#### 7.1 MiB/s done Bytes transferred = 44727 (aeb7 hex) => setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x12000000 0x12C00000 0x18000000 bootz 0x12000000 0x12C00000 0x18000000 Kernel image @ 0x12000000 [ 0x000000 - 0xa070a0 ] ## Loading init Ramdisk from Legacy Image at 12c00000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 10175564 Bytes = 9.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 18000000 Booting using the fdt blob at 0x18000000 Using Device Tree in place at 18000000, end 1800deb6 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.129-cip12 (KernelCI@build-j380649-arm-gcc-10-imx-v6-v7-defconfig-cftnh) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Thu Jul 21 09:08:01 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad Plus SABRE Smart Device Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x02020000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s51884 r8192 d21844 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 933396K/1048576K available (14336K kernel code, 2022K rwdata, 4840K rodata, 1024K init, 6661K bss, 49644K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 erratum 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000009] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008443] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.020384] Console: colour dummy device 80x30 <4>[ 0.023055] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.031088] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.035405] ... MAX_LOCK_DEPTH: 48 <4>[ 0.039865] ... MAX_LOCKDEP_KEYS: 8192 <4>[ 0.044454] ... CLASSHASH_SIZE: 4096 <4>[ 0.049085] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.053761] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.058482] ... CHAINHASH_SIZE: 32768 <4>[ 0.063158] memory used by lock dependency info: 4061 kB <4>[ 0.068833] memory used for stack traces: 2112 kB <4>[ 0.073859] per task-struct memory footprint: 1536 bytes <6>[ 0.079601] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.089988] pid_max: default: 32768 minimum: 301 <6>[ 0.095202] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.102446] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.113925] CPU: Testing write buffer coherency: ok <6>[ 0.116370] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.122660] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.130518] Setting up static identity map for 0x10100000 - 0x10100078 <6>[ 0.135215] rcu: Hierarchical SRCU implementation. <6>[ 0.142137] smp: Bringing up secondary CPUs ... <6>[ 0.147636] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.147652] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.159844] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.159860] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.171443] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.171457] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.180590] smp: Brought up 1 node, 4 CPUs <6>[ 0.184207] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.190801] CPU: All CPU(s) started in SVC mode. <6>[ 0.198455] devtmpfs: initialized <6>[ 0.245802] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.253751] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.261161] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.272186] pinctrl core: initialized pinctrl subsystem <6>[ 0.281320] NET: Registered protocol family 16 <6>[ 0.311641] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.321664] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.322218] cpuidle: using governor menu <6>[ 0.330028] CPU identified as i.MX6QP, silicon rev 1.0 <6>[ 0.898681] vdd3p0: supplied by regulator-dummy <6>[ 2.378300] No ATAGs? <6>[ 2.378908] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 2.386350] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 2.399050] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 2.532852] mxs-dma 110000.dma-apbh: initialized <6>[ 2.550803] vgaarb: loaded <5>[ 2.553392] SCSI subsystem initialized <6>[ 2.556903] usbcore: registered new interface driver usbfs <6>[ 2.560946] usbcore: registered new interface driver hub <6>[ 2.566488] usbcore: registered new device driver usb <4>[ 2.572120] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 2.580339] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 2.588422] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 2.596576] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <6>[ 2.625071] i2c i2c-0: IMX I2C adapter registered <6>[ 2.657518] i2c i2c-1: IMX I2C adapter registered <6>[ 2.666807] i2c i2c-2: IMX I2C adapter registered <6>[ 2.671582] mc: Linux media interface: v0.10 <6>[ 2.673597] videodev: Linux video capture interface: v2.00 <6>[ 2.679967] pps_core: LinuxPPS API ver. 1 registered <6>[ 2.684429] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 2.693937] PTP clock support registered <6>[ 2.700043] Advanced Linux Sound Architecture Driver Initialized. <6>[ 2.709891] Bluetooth: Core ver 2.22 <6>[ 2.711030] NET: Registered protocol family 31 <6>[ 2.715595] Bluetooth: HCI device and connection manager initialized <6>[ 2.722406] Bluetooth: HCI socket layer initialized <6>[ 2.727432] Bluetooth: L2CAP socket layer initialized <6>[ 2.732808] Bluetooth: SCO socket layer initialized <6>[ 2.740527] clocksource: Switched to clocksource mxc_timer1 <5>[ 4.323890] VFS: Disk quotas dquot_6.6.0 <6>[ 4.325434] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) <6>[ 4.371398] NET: Registered protocol family 2 <6>[ 4.373830] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 4.383974] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 22528 bytes, linear) <6>[ 4.390458] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 4.398009] TCP bind hash table entries: 8192 (order: 6, 327680 bytes, linear) <6>[ 4.406555] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 4.413134] UDP hash table entries: 512 (order: 3, 49152 bytes, linear) <6>[ 4.419012] UDP-Lite hash table entries: 512 (order: 3, 49152 bytes, linear) <6>[ 4.427072] NET: Registered protocol family 1 <6>[ 4.433537] RPC: Registered named UNIX socket transport module. <6>[ 4.436969] RPC: Registered udp transport module. <6>[ 4.441998] RPC: Registered tcp transport module. <6>[ 4.446877] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 4.455615] PCI: CLS 0 bytes, default 64 <6>[ 4.459153] Trying to unpack rootfs image as initramfs... <6>[ 5.649530] Freeing initrd memory: 9940K <4>[ 5.652640] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 5.659179] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 5.673870] Initialise system trusted keyrings <6>[ 5.676659] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <5>[ 5.709394] NFS: Registering the id_resolver key type <5>[ 5.712139] Key type id_resolver registered <5>[ 5.716327] Key type id_legacy registered <6>[ 5.721016] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 5.727625] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 5.735440] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. <6>[ 5.743672] fuse: init (API version 7.32) <5>[ 5.841401] Key type asymmetric registered <5>[ 5.843059] Asymmetric key parser 'x509' registered <6>[ 5.848331] bounce: pool size: 64 pages <6>[ 5.852366] io scheduler mq-deadline registered <6>[ 5.856939] io scheduler kyber registered <4>[ 5.872312] pwm-backlight backlight-lvds: supply power not found, using dummy regulator <4>[ 5.898797] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <4>[ 5.905907] imx-sdma 20ec000.sdma: Falling back to sysfs fallback for: imx/sdma/sdma-imx6q.bin <6>[ 5.916615] pfuze100-regulator 1-0008: Full layer: 2, Metal layer: 1 <6>[ 5.922341] pfuze100-regulator 1-0008: FAB: 0, FIN: 0 <6>[ 5.926594] pfuze100-regulator 1-0008: pfuze100 found. <6>[ 5.972440] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 33, base_baud = 5000000) is a IMX <6>[ 5.979261] printk: console [ttymxc0] enabled <6>[ 5.979261] printk: console [ttymxc0] enabled <6>[ 5.987901] printk: bootconsole [ec_imx21] disabled <6>[ 5.987901] printk: bootconsole [ec_imx21] disabled <4>[ 6.025590] panel-simple panel: supply power not found, using dummy regulator <6>[ 6.052406] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 6.068403] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops) <6>[ 6.076841] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops) <6>[ 6.085255] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops) <6>[ 6.093497] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops) <6>[ 6.102764] dwhdmi-imx 120000.hdmi: Detected HDMI TX controller v1.30a with HDCP (DWC HDMI 3D TX PHY) <6>[ 6.120251] imx-drm display-subsystem: bound 120000.hdmi (ops dw_hdmi_imx_ops) <6>[ 6.128858] imx-drm display-subsystem: bound ldb (ops imx_ldb_ops) <6>[ 6.140251] [drm] Initialized imx-drm 1.0.0 20120507 for display-subsystem on minor 0 <6>[ 6.222267] Console: switching to colour frame buffer device 128x48 <6>[ 6.244514] imx-drm display-subsystem: [drm] fb0: imx-drmdrmfb frame buffer device <6>[ 6.253088] imx-ipuv3 2800000.ipu: IPUv3H probed <6>[ 6.297105] brd: module loaded <6>[ 6.349749] loop: module loaded <6>[ 6.356670] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 6.365005] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 6.373798] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 6.382349] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 6.390923] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 6.399367] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 6.407347] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 6.418795] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 6.426163] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 6.435312] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 6.449467] scsi host0: ahci-imx <6>[ 6.455135] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 85 <3>[ 6.479348] spi-nor spi0.0: unrecognized JEDEC id bytes: 00 00 00 00 00 00 <6>[ 6.495783] CAN device driver interface <6>[ 6.505848] pps pps0: new PPS source ptp0 <6>[ 6.564092] vddpu: supplied by SW1C <6>[ 6.568902] usb_otg_vbus: supplied by SWBST <6>[ 6.573943] usb_h1_vbus: supplied by SWBST <6>[ 6.584701] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 6.594836] usbcore: registered new interface driver r8152 <6>[ 6.600828] usbcore: registered new interface driver lan78xx <6>[ 6.606958] usbcore: registered new interface driver asix <6>[ 6.612821] usbcore: registered new interface driver ax88179_178a <6>[ 6.619319] usbcore: registered new interface driver cdc_ether <6>[ 6.625693] usbcore: registered new interface driver smsc95xx <6>[ 6.631904] usbcore: registered new interface driver net1080 <6>[ 6.637972] usbcore: registered new interface driver cdc_subset <6>[ 6.644351] usbcore: registered new interface driver zaurus <6>[ 6.650330] usbcore: registered new interface driver MOSCHIP usb-ethernet driver <6>[ 6.658274] usbcore: registered new interface driver cdc_ncm <6>[ 6.664273] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 6.671135] ehci-pci: EHCI PCI platform driver <6>[ 6.676013] ehci-mxc: Freescale On-Chip EHCI Host driver <6>[ 6.683091] usbcore: registered new interface driver usb-storage <6>[ 6.701753] input: 20cc000.snvs:snvs-powerkey as /devices/platform/soc/2000000.bus/20cc000.snvs/20cc000.snvs:snvs-powerkey/input/input0 <3>[ 6.719522] egalax_ts 1-0004: Failed to read firmware version <3>[ 6.726477] egalax_ts 2-0004: Failed to read firmware version <4>[ 6.732653] egalax_ts: probe of 2-0004 failed with error -11 <6>[ 6.751439] snvs_rtc 20cc000.snvs:snvs-rtc-lp: registered as rtc0 <6>[ 6.757925] snvs_rtc 20cc000.snvs:snvs-rtc-lp: setting system clock to 1970-01-01T00:00:39 UTC (39) <6>[ 6.767944] i2c /dev entries driver <6>[ 6.790630] Bluetooth: HCI UART driver ver 2.3 <6>[ 6.793386] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 6.795369] Bluetooth: HCI UART protocol H4 registered <6>[ 6.795484] Bluetooth: HCI UART protocol LL registered <6>[ 6.801547] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 6.810864] sdhci: Secure Digital Host Controller Interface driver <6>[ 6.812041] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 6.818523] sdhci: Copyright(c) Pierre Ossman <6>[ 6.818535] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 6.847070] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 6.847077] sdhci-esdhc-imx 2194000.mmc: Got CD GPIO <6>[ 6.847275] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 6.851144] caam 2100000.crypto: Entropy delay = 3200 <6>[ 6.852677] sdhci-esdhc-imx 2194000.mmc: Got WP GPIO <6>[ 6.897263] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 6.906051] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 6.911950] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 6.969176] mmc2: new high speed SDHC card at address aaaa <6>[ 6.972713] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 6.980257] mmc3: new DDR MMC card at address 0001 <6>[ 6.980646] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 6.980834] mmc1: SDHCI controller on 2194000.mmc [2194000.mmc] using ADMA <6>[ 6.988371] mmcblk3: mmc3:0001 Q2J55L 7.13 GiB <6>[ 6.992566] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 7.010662] mmcblk2: mmc2:aaaa SS08G 7.40 GiB <6>[ 7.017166] mmcblk3boot0: mmc3:0001 Q2J55L partition 1 2.00 MiB <6>[ 7.024501] mmcblk3boot1: mmc3:0001 Q2J55L partition 2 2.00 MiB <6>[ 7.025248] caam algorithms registered in /proc/crypto <6>[ 7.035137] mmcblk3rpmb: mmc3:0001 Q2J55L partition 3 4.00 MiB, chardev (243:0) <6>[ 7.042526] caam 2100000.crypto: registering rng-caam <6>[ 7.057495] usbcore: registered new interface driver usbhid <6>[ 7.063496] usbhid: USB HID core driver <6>[ 7.073347] ipu1_csi0: Registered ipu1_csi0 capture as /dev/video0 <6>[ 7.082356] ipu1_ic_prpenc: Registered ipu1_ic_prpenc capture as /dev/video1 <6>[ 7.090915] ipu1_ic_prpvf: Registered ipu1_ic_prpvf capture as /dev/video2 <6>[ 7.099551] ipu1_csi1: Registered ipu1_csi1 capture as /dev/video3 <6>[ 7.107581] ipu2_csi0: Registered ipu2_csi0 capture as /dev/video4 <6>[ 7.114987] ipu2_ic_prpenc: Registered ipu2_ic_prpenc capture as /dev/video5 <6>[ 7.123222] ipu2_ic_prpvf: Registered ipu2_ic_prpvf capture as /dev/video6 <6>[ 7.131754] ipu2_csi1: Registered ipu2_csi1 capture as /dev/video7 <6>[ 7.145167] mma8452 0-001c: registering mma8451 accelerometer; ID 0x1a <4>[ 7.211634] isl29018 2-0044: No cache defaults, reading back from HW <3>[ 7.219641] isl29018 2-0044: Failed to read 1: -6 <3>[ 7.224730] isl29018 2-0044: regmap initialization fails: -6 <5>[ 7.233800] random: crng init done <6>[ 7.266875] wm8962 0-001a: customer id 0 revision D <4>[ 7.305721] fsl-ssi-dai 202c000.ssi: No cache defaults, reading back from HW <6>[ 7.324077] NET: Registered protocol family 10 <6>[ 7.333788] Segment Routing with IPv6 <6>[ 7.337884] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 7.346997] NET: Registered protocol family 17 <6>[ 7.351963] can: controller area network core <6>[ 7.356872] NET: Registered protocol family 29 <6>[ 7.361761] can: raw protocol <6>[ 7.365172] can: broadcast manager protocol <6>[ 7.369687] can: netlink gateway - max_hops=1 <5>[ 7.375012] Key type dns_resolver registered <5>[ 7.384828] Registering SWP/SWPB emulation handler <5>[ 7.390828] Loading compiled-in X.509 certificates <6>[ 7.567459] vdd1p1: supplied by VGEN5 <6>[ 7.575655] vdd2p5: supplied by VGEN5 <6>[ 7.581970] vddarm: supplied by SW2 <6>[ 7.588072] vddsoc: supplied by SW1C <6>[ 7.612254] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops) <6>[ 7.619661] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops) <6>[ 7.626549] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops) <6>[ 7.632621] etnaviv-gpu 130000.gpu: model: GC3000, revision: 5450 <6>[ 7.640268] etnaviv-gpu 134000.gpu: model: GC320, revision: 5303 <6>[ 7.646881] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1216 <6>[ 7.653367] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 7.662616] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 1 <4>[ 7.687276] imx_usb 2184200.usb: No over current polarity defined <6>[ 7.699322] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 7.705125] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 7.740607] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 7.748361] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 <6>[ 7.757201] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>[ 7.764784] usb usb1: Product: EHCI Host Controller <6>[ 7.769961] usb usb1: Manufacturer: Linux 5.10.129-cip12 ehci_hcd <6>[ 7.776415] usb usb1: SerialNumber: ci_hdrc.1 <6>[ 7.786268] hub 1-0:1.0: USB hub found <6>[ 7.790873] hub 1-0:1.0: 1 port detected <6>[ 7.815753] input: WM8962 Beep Generator as /devices/platform/soc/2100000.bus/21a0000.i2c/i2c-0/0-001a/input/input3 <3>[ 7.895407] wm8962 0-001a: ASoC: error at soc_component_read_no_lock on wm8962.0-001a: -16 <3>[ 7.904327] wm8962 0-001a: ASoC: error at soc_component_read_no_lock on wm8962.0-001a: -16 <6>[ 7.941198] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <6>[ 7.962673] input: gpio-keys as /devices/platform/gpio-keys/input/input6 <6>[ 8.063069] Qualcomm Atheros AR8031/AR8033 2188000.ethernet-1:01: attached PHY driver [Qualcomm Atheros AR8031/AR8033] (mii_bus:phy_addr=2188000.ethernet-1:01, irq=POLL) <6>[ 11.202962] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 11.231128] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 11.260705] Sending DHCP requests .., OK <6>[ 14.165381] IP-Config: Got DHCP answer from 172.16.1.4, my address is 172.16.1.241 <6>[ 14.173472] IP-Config: Complete: <6>[ 14.177036] device=eth0, hwaddr=00:04:9f:05:b8:c3, ipaddr=172.16.1.241, mask=255.255.255.0, gw=172.16.1.4 <6>[ 14.187619] host=172.16.1.241, domain=example.org, nis-domain=(none) <6>[ 14.194856] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 14.194895] nameserver0=172.16.1.4 <5>[ 14.212732] cfg80211: Loading compiled-in X.509 certificates for regulatory database <5>[ 14.278578] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' <4>[ 14.288027] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 <6>[ 14.290542] ALSA device list: <4>[ 14.297070] platform regulatory.0: Falling back to sysfs fallback for: regulatory.db <6>[ 14.300227] #0: wm8962-audio <6>[ 14.315923] Freeing unused kernel memory: 1024K <6>[ 14.352238] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 14.746148] udevd[214]: starting version 3.2.9 <27>[ 14.766585] udevd[214]: specified user 'tss' unknown <27>[ 14.772744] udevd[214]: specified group 'tss' unknown <30>[ 14.786910] udevd[215]: starting eudev-3.2.9 <4>[ 15.468582] coda 2040000.vpu: Direct firmware load for vpu_fw_imx6q.bin failed with error -2 <4>[ 15.477467] coda 2040000.vpu: Falling back to sysfs fallback for: vpu_fw_imx6q.bin <3>[ 15.732176] ov5640 1-003c: ov5640_read_reg: error: reg=300a <3>[ 15.738059] ov5640 1-003c: ov5640_check_chip_id: failed to read chip identifier done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1014354/environment . /lava-1014354/environment / # /lava-1014354/bin/lava-test-runner /lava-1014354/0 /lava-1014354/bin/lava-test-runner /lava-1014354/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1014354/0/tests/0_dmesg + cat uuid + UUID=1014354_1.5.2.4.1<8>[ 22.340258] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 22.461049] <8>[ 22.564353] <8>[ 22.671326] + set +x <8>[ 22.683073] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-1014354/environment / # . /lava-1014354/environment/lava-1014354/bin/lava-test-runner /lava-1014354/1 / # /lava-1014354/bin/lava-test-runner /lava-1014354/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1014354/1/tests/1_bootrr + cat uuid + UUID=1014354_1.5.2.4.5<8>[ 28.552734] + set +x + export 'PATH=/opt/bootrr/helpers:/lava-1014354/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr + sh helpers/bootrr-auto /lava-1014354/1/../bin/lava-test-case <8>[ 29.691827] /lava-1014354/1/../bin/lava-test-case <8>[ 29.798033] /lava-1014354/1/../bin/lava-test-case <8>[ 29.857759] + set +x <8>[ 29.900013] / #