connecting to NetworkSerialPort(target=Target(name='tegra124-jetson-tk1', env=None), name='USBSerialPort', state=, avail=True, host='nuc-1', port=49863, speed=115200, protocol='rfc2217') calling microcom -s 115200 -t nuc-1:49863 connected to 192.168.0.1 (port 49863) Escape character: Ctrl-\ Type the escape character to get to the prompt. U-Boot SPL 2015.10 (Dec 03 2015 - 13:25:02) U-Boot 2015.10 (Dec 03 2015 - 13:25:02 -0800) TEGRA124 Model: NVIDIA Jetson TK1 Board: NVIDIA Jetson TK1 DRAM: 2 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 tegra-pcie: PCI regions: tegra-pcie: I/O: 0x12000000-0x12010000 tegra-pcie: non-prefetchable memory: 0x13000000-0x20000000 tegra-pcie: prefetchable memory: 0x20000000-0x40000000 tegra-pcie: 2x1, 1x1 configuration tegra-pcie: probing port 0, using 2 lanes tegra-pcie: link 0 down, retrying tegra-pcie: link 0 down, retrying tegra-pcie: link 0 down, retrying tegra-pcie: link 0 down, ignoring tegra-pcie: probing port 1, using 1 lanes In: serial Out: serial Err: serial Net: RTL8169#0 Hit any key to stop autoboot: 2  0 Tegra124 (Jetson TK1) # setenv autoload no setenv autoload no Tegra124 (Jetson TK1) # setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff Tegra124 (Jetson TK1) # setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff Tegra124 (Jetson TK1) # dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.0.213 (7 ms) Tegra124 (Jetson TK1) # setenv serverip 192.168.0.2 setenv serverip 192.168.0.2 Tegra124 (Jetson TK1) # tftp 0x81000000 2318521/tftp-deploy-tus30xqi/kernel/zImage tftp 0x81000000 2318521/tftp-deploy-tus30xqi/kernel/zImage Using RTL8169#0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.213 Filename '2318521/tftp-deploy-tus30xqi/kernel/zImage'. Load address: 0x81000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######### 2.1 MiB/s done Bytes transferred = 9667072 (938200 hex) Tegra124 (Jetson TK1) # tftp 0x82800000 2318521/tftp-deploy-tus30xqi/ramdisk/ramdisk.cpio.gz.uboot tftp 0x82800000 2318521/tftp-deploy-tus30xqi/ramdisk/ramdisk.cpio.gz.uboot Using RTL8169#0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.213 Filename '2318521/tftp-deploy-tus30xqi/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x82800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ###################################################### 3 MiB/s done Bytes transferred = 16058070 (f506d6 hex) Tegra124 (Jetson TK1) # setenv initrd_size ${filesize} setenv initrd_size ${filesize} Tegra124 (Jetson TK1) # tftp 0x83f80000 2318521/tftp-deploy-tus30xqi/dtb/tegra124-jetson-tk1.dtb tftp 0x83f80000 2318521/tftp-deploy-tus30xqi/dtb/tegra124-jetson-tk1.dtb Using RTL8169#0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.213 Filename '2318521/tftp-deploy-tus30xqi/dtb/tegra124-jetson-tk1.dtb'. Load address: 0x83f80000 Loading: *##### 2.8 MiB/s done Bytes transferred = 66855 (10527 hex) Tegra124 (Jetson TK1) # setenv bootargs 'console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=:::::eth0:dhcp' setenv bootargs 'console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=:::::eth0:dhcp' Tegra124 (Jetson TK1) # bootz 0x81000000 0x82800000 0x83f80000 bootz 0x81000000 0x82800000 0x83f80000 Kernel image @ 0x81000000 [ 0x000000 - 0x938200 ] ## Loading init Ramdisk from Legacy Image at 82800000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16058006 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 83f80000 Booting using the fdt blob at 0x83f80000 Using Device Tree in place at 83f80000, end 83f93526 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.135-cip13 (KernelCI@build-j447844-arm-gcc-10-multi-v7-defconfig-wcbzm) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Aug 3 14:37:55 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [413fc0f3] revision 3 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: NVIDIA Tegra124 Jetson TK1 [ 0.000000] earlycon: uart0 at MMIO 0x70006300 (options '115200n8') [ 0.000000] printk: bootconsole [uart0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0xfb800000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000afffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x00000000b0000000-0x00000000ffefffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000ffefffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000000ffefffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522496 [ 0.000000] Kernel command line: console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=:::::eth0:dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 1972984K/2096128K available (13312K kernel code, 2230K rwdata, 5340K rodata, 2048K init, 425K bss, 57608K reserved, 65536K cma-reserved, 1244160K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] /interrupt-controller@60004000: 160 interrupts forwarded to /interrupt-controller@50041000 <6>[ 0.000010] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483647500ns <6>[ 0.008951] clocksource: timer_us: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275 ns <6>[ 0.019147] Switching to timer-based delay loop, resolution 1000ns <6>[ 0.030369] clocksource: tegra_suspend_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns <6>[ 0.044067] arch_timer: cp15 timer(s) running at 12.00MHz (virt). <6>[ 0.050664] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2c47f4ee7, max_idle_ns: 440795202497 ns <6>[ 0.062123] sched_clock: 56 bits at 12MHz, resolution 83ns, wraps every 4398046511096ns <6>[ 0.070695] Switching to timer-based delay loop, resolution 83ns <6>[ 0.077758] Console: colour dummy device 80x30 <6>[ 0.082671] Calibrating delay loop (skipped), value calculated using timer frequency.. 24.00 BogoMIPS (lpj=120000) <6>[ 0.093694] pid_max: default: 32768 minimum: 301 <6>[ 0.098894] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.106760] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.115647] CPU: Testing write buffer coherency: ok <6>[ 0.121024] CPU0: Spectre v2: using ICIALLU workaround <6>[ 0.126623] CPU0: Spectre BHB: enabling loop workaround for all CPUs <3>[ 0.133691] /cpus/cpu@0 missing clock-frequency property <3>[ 0.139503] /cpus/cpu@1 missing clock-frequency property <3>[ 0.145329] /cpus/cpu@2 missing clock-frequency property <3>[ 0.151140] /cpus/cpu@3 missing clock-frequency property <6>[ 0.156932] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.163597] Setting up static identity map for 0x80300000 - 0x803000ac <6>[ 0.172631] rcu: Hierarchical SRCU implementation. <6>[ 0.181324] Tegra Revision: A01 SKU: 129 CPU Process: 1 SoC Process: 1 <6>[ 0.189171] EFI services will not be available. <6>[ 0.194379] smp: Bringing up secondary CPUs ... <6>[ 0.199986] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <3>[ 0.199994] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable <6>[ 0.216998] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <3>[ 0.217006] CPU2: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable <6>[ 0.233992] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <3>[ 0.234000] CPU3: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable <6>[ 0.250365] smp: Brought up 1 node, 4 CPUs <6>[ 0.254906] SMP: Total of 4 processors activated (96.00 BogoMIPS). <6>[ 0.261583] CPU: All CPU(s) started in SVC mode. <6>[ 0.267180] devtmpfs: initialized <6>[ 0.283928] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 <6>[ 0.292363] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.302855] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.311563] pinctrl core: initialized pinctrl subsystem <6>[ 0.319121] DMI not present or invalid. <6>[ 0.323979] NET: Registered protocol family 16 <6>[ 0.331053] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.341198] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.341864] cpuidle: using governor menu <6>[ 0.453790] No ATAGs? <6>[ 0.456550] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.465143] hw-breakpoint: maximum watchpoint size is 8 bytes. <6>[ 0.486760] Serial: AMBA PL011 UART driver <6>[ 0.492841] platform 50000000.host1x: Adding to iommu group 0 <6>[ 0.499152] platform 57000000.gpu: Adding to iommu group 1 <6>[ 0.532695] +5V_SYS: supplied by +VDD_MUX <6>[ 0.537522] +3.3V_SYS: supplied by +VDD_MUX <6>[ 0.543102] +USB0_VBUS_SW: supplied by +5V_SYS <6>[ 0.548363] +5V_USB_HS: supplied by +5V_SYS <6>[ 0.553780] +5V_HDMI_CON: supplied by +5V_SYS <6>[ 0.558964] +5V_SATA: supplied by +5V_SYS <6>[ 0.563642] reg-fixed-voltage regulator@11: nonexclusive access to GPIO for regulator@11 <6>[ 0.572478] +12V_SATA: supplied by +VDD_MUX <6>[ 0.579582] iommu: Default domain type: Translated <6>[ 0.585229] vgaarb: loaded <5>[ 0.589088] SCSI subsystem initialized <6>[ 0.593714] usbcore: registered new interface driver usbfs <6>[ 0.599784] usbcore: registered new interface driver hub <6>[ 0.605600] usbcore: registered new device driver usb <6>[ 0.612537] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.617957] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.627725] PTP clock support registered <6>[ 0.635512] clocksource: Switched to clocksource arch_sys_counter <6>[ 1.693871] NET: Registered protocol family 2 <6>[ 1.698884] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.707966] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 1.716947] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 1.725325] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 1.733196] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 1.740157] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.747349] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.755079] NET: Registered protocol family 1 <6>[ 1.760391] RPC: Registered named UNIX socket transport module. <6>[ 1.766835] RPC: Registered udp transport module. <6>[ 1.771989] RPC: Registered tcp transport module. <6>[ 1.777156] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.784109] PCI: CLS 0 bytes, default 64 <6>[ 1.788825] Trying to unpack rootfs image as initramfs... <6>[ 2.937651] Freeing initrd memory: 15684K <6>[ 2.942983] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available <5>[ 2.952904] Initialise system trusted keyrings <6>[ 2.958049] workingset: timestamp_bits=30 max_order=19 bucket_order=0 <6>[ 2.971651] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 2.978682] NFS: Registering the id_resolver key type <5>[ 2.984218] Key type id_resolver registered <5>[ 2.988851] Key type id_legacy registered <6>[ 2.993377] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.000616] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.008596] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.013802] Key type asymmetric registered <5>[ 3.018344] Asymmetric key parser 'x509' registered <6>[ 3.023720] bounce: pool size: 64 pages <6>[ 3.028008] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 3.035964] io scheduler mq-deadline registered <6>[ 3.040931] io scheduler kyber registered <6>[ 3.064157] tegra-pcie 1003000.pcie: host bridge /pcie@1003000 ranges: <6>[ 3.071253] tegra-pcie 1003000.pcie: MEM 0x0001000000..0x0001001fff -> 0x0001000000 <6>[ 3.079958] tegra-pcie 1003000.pcie: IO 0x0012000000..0x001200ffff -> 0x0000000000 <6>[ 3.088651] tegra-pcie 1003000.pcie: MEM 0x0013000000..0x001fffffff -> 0x0013000000 <6>[ 3.097350] tegra-pcie 1003000.pcie: MEM 0x0020000000..0x003fffffff -> 0x0020000000 <6>[ 3.106151] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration <6>[ 3.124675] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver registered 32 channels <6>[ 3.137962] tegra-pmc 7000e400.pmc: emergency thermal reset enabled <6>[ 3.202033] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.212519] printk: console [ttyS0] disabled <6>[ 3.217305] 70006300.serial: ttyS0 at MMIO 0x70006300 (irq = 84, base_baud = 25500000) is a Tegra <6>[ 3.226820] printk: console [ttyS0] enabled <6>[ 3.226820] printk: console [ttyS0] enabled <6>[ 3.235863] printk: bootconsole [uart0] disabled <6>[ 3.235863] printk: bootconsole [uart0] disabled <6>[ 3.247049] SuperH (H)SCI(F) driver initialized <6>[ 3.252912] msm_serial: driver initialized <6>[ 3.257483] STMicroelectronics ASC driver initialized <6>[ 3.263818] 70006000.serial: ttyTHS1 at MMIO 0x70006000 (irq = 82, base_baud = 0) is a TEGRA_UART <6>[ 3.273513] 70006040.serial: ttyTHS2 at MMIO 0x70006040 (irq = 83, base_baud = 0) is a TEGRA_UART <6>[ 3.283660] STM32 USART driver initialized <6>[ 3.291519] platform 54200000.dc: Adding to iommu group 2 <6>[ 3.299816] platform 54240000.dc: Adding to iommu group 2 <6>[ 3.310562] platform 54340000.vic: Adding to iommu group 2 <4>[ 3.320709] Failed to attached device 54200000.dc to IOMMU_mapping <4>[ 3.335513] Failed to attached device 54240000.dc to IOMMU_mapping <4>[ 3.352524] Failed to attached device 54340000.vic to IOMMU_mapping <6>[ 3.369858] brd: module loaded <6>[ 3.381161] loop: module loaded <4>[ 3.387847] tegra-ahci 70027000.sata: supply ahci not found, using dummy regulator <4>[ 3.395833] tegra-ahci 70027000.sata: supply phy not found, using dummy regulator <6>[ 3.413754] spi-nor spi1.0: w25q32dw (4096 Kbytes) <6>[ 3.424187] CAN device driver interface <6>[ 3.429327] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.436508] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.441729] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.447983] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.453637] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.464253] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.471963] usbcore: registered new interface driver pegasus <6>[ 3.477941] usbcore: registered new interface driver asix <6>[ 3.483625] usbcore: registered new interface driver ax88179_178a <6>[ 3.490025] usbcore: registered new interface driver cdc_ether <6>[ 3.496174] usbcore: registered new interface driver smsc75xx <6>[ 3.502214] usbcore: registered new interface driver smsc95xx <6>[ 3.508266] usbcore: registered new interface driver net1080 <6>[ 3.514209] usbcore: registered new interface driver cdc_subset <6>[ 3.520434] usbcore: registered new interface driver zaurus <6>[ 3.526343] usbcore: registered new interface driver cdc_ncm <4>[ 3.532624] tegra-phy 7d000000.usb-phy: supply vbus not found, using dummy regulator <4>[ 3.540932] tegra-phy 7d004000.usb-phy: supply vbus not found, using dummy regulator <6>[ 3.551961] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.558768] ehci-pci: EHCI PCI platform driver <6>[ 3.563504] ehci-platform: EHCI generic platform driver <6>[ 3.569217] ehci-orion: EHCI orion driver <6>[ 3.573654] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.578090] ehci-st: EHCI STMicroelectronics driver <6>[ 3.583374] ehci-exynos: EHCI Exynos driver <6>[ 3.587980] ehci-atmel: EHCI Atmel driver <6>[ 3.592385] tegra-ehci: Tegra EHCI driver <6>[ 3.601091] tegra-ehci 7d004000.usb: EHCI Host Controller <6>[ 3.606794] tegra-ehci 7d004000.usb: new USB bus registered, assigned bus number 1 <6>[ 3.614802] tegra-ehci 7d004000.usb: irq 105, io mem 0x7d004000 <6>[ 3.645504] tegra-ehci 7d004000.usb: USB 2.0 started, EHCI 1.10 <6>[ 3.652394] hub 1-0:1.0: USB hub found <6>[ 3.656459] hub 1-0:1.0: 1 port detected <6>[ 3.663243] tegra-ehci 7d008000.usb: EHCI Host Controller <6>[ 3.668935] tegra-ehci 7d008000.usb: new USB bus registered, assigned bus number 2 <6>[ 3.676926] tegra-ehci 7d008000.usb: irq 106, io mem 0x7d008000 <6>[ 3.705505] tegra-ehci 7d008000.usb: USB 2.0 started, EHCI 1.10 <6>[ 3.712334] hub 2-0:1.0: USB hub found <6>[ 3.716398] hub 2-0:1.0: 1 port detected <6>[ 3.721024] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.727488] ohci-pci: OHCI PCI platform driver <6>[ 3.732233] ohci-platform: OHCI generic platform driver <6>[ 3.737935] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.742355] ohci-st: OHCI STMicroelectronics driver <6>[ 3.747662] ohci-atmel: OHCI Atmel driver <6>[ 3.752771] usbcore: registered new interface driver usb-storage <6>[ 3.770973] tegra_rtc 7000e000.rtc: registered as rtc1 <5>[ 3.776399] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock <6>[ 3.783450] i2c /dev entries driver <4>[ 3.794610] at24 0-0056: supply vcc not found, using dummy regulator <6>[ 3.802329] at24 0-0056: 256 byte 24c02 EEPROM, writable, 8 bytes/write <6>[ 3.815174] as3722 4-0040: AS3722 with revision 0x1 found <6>[ 3.827998] +1.35V_LP0(sd2): supplied by +5V_SYS <6>[ 3.833300] +1.35V_LP0(sd3): Bringing 0uV into 1350000-1350000uV <6>[ 3.839724] +1.35V_LP0(sd3): supplied by +5V_SYS <6>[ 3.845203] +1.05V_RUN: supplied by +5V_SYS <6>[ 3.849923] +1.8V_VDDIO: supplied by +5V_SYS <6>[ 3.856278] +1.05V_RUN_AVDD: supplied by +1.35V_LP0(sd2) <6>[ 3.862717] +1.8V_RUN_CAM: Bringing 0uV into 1800000-1800000uV <6>[ 3.869365] +1.2V_GEN_AVDD: supplied by +1.8V_VDDIO <6>[ 3.875587] +1.05V_LP0_VDD_RTC: Bringing 1100000uV into 1000000-1000000uV <6>[ 3.882760] +1.05V_LP0_VDD_RTC: supplied by +3.3V_SYS <6>[ 3.889139] +2.8V_RUN_CAM: Bringing 0uV into 2800000-2800000uV <6>[ 3.895586] +2.8V_RUN_CAM: supplied by +3.3V_SYS <6>[ 3.900697] +1.2V_RUN_CAM_FRONT: Bringing 0uV into 1200000-1200000uV <6>[ 3.907675] +1.2V_RUN_CAM_FRONT: supplied by +1.8V_VDDIO <3>[ 3.913483] +VDDIO_SDMMC3: bypassed regulator has no supply! <3>[ 3.919422] +VDDIO_SDMMC3: failed to get the current voltage: -EPROBE_DEFER <3>[ 3.926678] as3722-regulator as3722-regulator: regulator 13 register failed -517 <6>[ 3.939707] as3722-rtc as3722-rtc: registered as rtc0 <6>[ 3.945336] as3722-rtc as3722-rtc: setting system clock to 2000-01-01T00:00:18 UTC (946684818) <6>[ 3.954231] as3722-rtc as3722-rtc: RTC interrupt 388 <4>[ 3.968325] lm90 0-004c: supply vcc not found, using dummy regulator <6>[ 3.977687] hwmon hwmon0: temp1_input not attached to any thermal zone <6>[ 3.984610] hwmon hwmon0: temp2_input not attached to any thermal zone <6>[ 4.000567] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.007026] sdhci: Copyright(c) Pierre Ossman <6>[ 4.013856] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.021751] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.031724] sdhci-tegra 700b0400.mmc: Got CD GPIO <6>[ 4.036754] sdhci-tegra 700b0400.mmc: Got WP GPIO <4>[ 4.040177] mmc1: Invalid maximum block size, assuming 512 bytes <6>[ 4.048081] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.055152] usbcore: registered new interface driver usbhid <6>[ 4.061007] usbhid: USB HID core driver <6>[ 4.070288] NET: Registered protocol family 10 <6>[ 4.075801] Segment Routing with IPv6 <6>[ 4.079400] mmc1: SDHCI controller on 700b0600.mmc [700b0600.mmc] using ADMA 64-bit <6>[ 4.079793] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.094399] NET: Registered protocol family 17 <6>[ 4.099136] can: controller area network core <6>[ 4.103807] NET: Registered protocol family 29 <6>[ 4.108547] can: raw protocol <6>[ 4.111778] can: broadcast manager protocol <6>[ 4.116246] can: netlink gateway - max_hops=1 <5>[ 4.121223] Key type dns_resolver registered <6>[ 4.126949] ThumbEE CPU extension supported. <5>[ 4.131486] Registering SWP/SWPB emulation handler <5>[ 4.136978] Loading compiled-in X.509 certificates <6>[ 4.165416] +3.3V_RUN: supplied by +3.3V_SYS <6>[ 4.171525] +3.3V_LP0: supplied by +3.3V_SYS <6>[ 4.176735] +3.3V_AVDD_HDMI_AP_GATED: supplied by +3.3V_RUN <3>[ 4.183461] tegra-xusb-padctl 7009f000.padctl: failed to get regulators: -517 <6>[ 4.192992] tegra-pcie 1003000.pcie: host bridge /pcie@1003000 ranges: <6>[ 4.199866] tegra-pcie 1003000.pcie: MEM 0x0001000000..0x0001001fff -> 0x0001000000 <6>[ 4.208301] tegra-pcie 1003000.pcie: IO 0x0012000000..0x001200ffff -> 0x0000000000 <6>[ 4.216755] tegra-pcie 1003000.pcie: MEM 0x0013000000..0x001fffffff -> 0x0013000000 <6>[ 4.225135] tegra-pcie 1003000.pcie: MEM 0x0020000000..0x003fffffff -> 0x0020000000 <6>[ 4.233671] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration <4>[ 4.246234] tegra-ahci 70027000.sata: supply ahci not found, using dummy regulator <4>[ 4.254229] tegra-ahci 70027000.sata: supply phy not found, using dummy regulator <4>[ 4.263971] as3722-regulator as3722-regulator: DMA mask not set <6>[ 4.272665] +1.35V_LP0(sd2): supplied by +5V_SYS <6>[ 4.277891] +1.35V_LP0(sd3): supplied by +5V_SYS <6>[ 4.283233] +1.05V_RUN: supplied by +5V_SYS <6>[ 4.287825] +1.8V_VDDIO: supplied by +5V_SYS <6>[ 4.293921] +1.05V_RUN_AVDD: supplied by +1.35V_LP0(sd2) <6>[ 4.300299] +1.8V_RUN_CAM: supplied by +3.3V_RUN <6>[ 4.305299] +1.2V_GEN_AVDD: supplied by +1.8V_VDDIO <6>[ 4.311516] +1.05V_LP0_VDD_RTC: supplied by +3.3V_SYS <6>[ 4.318107] +2.8V_RUN_CAM: supplied by +3.3V_SYS <6>[ 4.323324] +1.2V_RUN_CAM_FRONT: supplied by +1.8V_VDDIO <3>[ 4.329114] +VDDIO_SDMMC3: bypassed regulator has no supply! <3>[ 4.335084] +VDDIO_SDMMC3: failed to get the current voltage: -EPROBE_DEFER <6>[ 4.342371] +VDDIO_SDMMC3: supplied by +3.3V_RUN <6>[ 4.348130] +1.05V_RUN_CAM_REAR: Bringing 0uV into 1050000-1050000uV <6>[ 4.355590] +1.05V_RUN_CAM_REAR: supplied by +1.8V_VDDIO <6>[ 4.362139] +3.3V_RUN_TOUCH: Bringing 0uV into 2800000-2800000uV <6>[ 4.369520] +3.3V_RUN_TOUCH: supplied by +5V_SYS <6>[ 4.374968] +2.8V_RUN_CAM_AF: Bringing 0uV into 2800000-2800000uV <6>[ 4.382125] +2.8V_RUN_CAM_AF: supplied by +5V_SYS <6>[ 4.388073] +1.8V_RUN_VPP_FUSE: Bringing 0uV into 1800000-1800000uV <6>[ 4.395517] +1.8V_RUN_VPP_FUSE: supplied by +3.3V_RUN <6>[ 4.405577] sdhci-tegra 700b0400.mmc: Got CD GPIO <4>[ 4.406720] usb2-0: supply vbus not found, using dummy regulator <6>[ 4.410616] sdhci-tegra 700b0400.mmc: Got WP GPIO <4>[ 4.417293] usb2-1: supply vbus not found, using dummy regulator <4>[ 4.428940] usb3-0: supply vbus not found, using dummy regulator <6>[ 4.435774] mmc1: new high speed MMC card at address 0001 <6>[ 4.437305] tegra-pcie 1003000.pcie: host bridge /pcie@1003000 ranges: <4>[ 4.442078] mmc0: Invalid maximum block size, assuming 512 bytes <6>[ 4.448328] tegra-pcie 1003000.pcie: MEM 0x0001000000..0x0001001fff -> 0x0001000000 <6>[ 4.454903] mmcblk1: mmc1:0001 SEM16G 14.7 GiB <6>[ 4.462944] tegra-pcie 1003000.pcie: IO 0x0012000000..0x001200ffff -> 0x0000000000 <6>[ 4.468018] mmcblk1boot0: mmc1:0001 SEM16G partition 1 4.00 MiB <6>[ 4.476176] tegra-pcie 1003000.pcie: MEM 0x0013000000..0x001fffffff -> 0x0013000000 <6>[ 4.482563] mmcblk1boot1: mmc1:0001 SEM16G partition 2 4.00 MiB <6>[ 4.490713] tegra-pcie 1003000.pcie: MEM 0x0020000000..0x003fffffff -> 0x0020000000 <6>[ 4.497176] mmcblk1rpmb: mmc1:0001 SEM16G partition 3 4.00 MiB, chardev (235:0) <6>[ 4.505495] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration <6>[ 4.522395] tegra-pcie 1003000.pcie: probing port 0, using 2 lanes <6>[ 4.529050] mmcblk1: p1 p2 p3 p4 p5 p6 p7 p8 <6>[ 4.530959] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes <6>[ 4.535002] mmc0: SDHCI controller on 700b0400.mmc [700b0400.mmc] using ADMA 64-bit <6>[ 4.889442] mmc0: new high speed SD card at address 0260 <6>[ 4.895721] mmcblk0: mmc0:0260 1232 961 MiB <6>[ 4.903387] mmcblk0: p1 p2 <6>[ 5.747693] tegra-pcie 1003000.pcie: link 0 down, ignoring <6>[ 5.757850] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 <6>[ 5.764383] pci_bus 0000:00: root bus resource [bus 00-ff] <6>[ 5.770160] pci_bus 0000:00: root bus resource [mem 0x01000000-0x01001fff] <6>[ 5.777305] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] <6>[ 5.783742] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] <6>[ 5.790885] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] <6>[ 5.798868] pci 0000:00:02.0: [10de:0e13] type 01 class 0x060400 <4>[ 5.805136] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4 may corrupt adjacent RW1C bits <6>[ 5.815093] pci 0000:00:02.0: enabling Extended Tags <6>[ 5.820404] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold <6>[ 5.831654] PCI: bus0: Fast back to back transfers disabled <6>[ 5.837507] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring <6>[ 5.845964] pci 0000:01:00.0: [10ec:8168] type 00 class 0x020000 <6>[ 5.852256] pci 0000:01:00.0: reg 0x10: [io 0x0000-0x00ff] <6>[ 5.858139] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit] <6>[ 5.865203] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] <6>[ 5.872876] pci 0000:01:00.0: supports D1 D2 <6>[ 5.877433] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold <6>[ 5.910005] PCI: bus1: Fast back to back transfers disabled <6>[ 5.915872] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 5.922767] pci 0000:00:02.0: BAR 8: assigned [mem 0x13000000-0x130fffff] <6>[ 5.929829] pci 0000:00:02.0: BAR 9: assigned [mem 0x20000000-0x200fffff 64bit pref] <6>[ 5.937842] pci 0000:00:02.0: BAR 7: assigned [io 0x1000-0x1fff] <6>[ 5.944199] pci 0000:01:00.0: BAR 4: assigned [mem 0x20000000-0x20003fff 64bit pref] <6>[ 5.952229] pci 0000:01:00.0: BAR 2: assigned [mem 0x13000000-0x13000fff 64bit] <6>[ 5.959825] pci 0000:01:00.0: BAR 0: assigned [io 0x1000-0x10ff] <6>[ 5.966195] pci 0000:00:02.0: PCI bridge to [bus 01] <6>[ 5.971420] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] <6>[ 5.977786] pci 0000:00:02.0: bridge window [mem 0x13000000-0x130fffff] <6>[ 5.984830] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref] <4>[ 5.992868] pci 0000:00:02.0: nv_msi_ht_cap_quirk didn't locate host bridge <6>[ 6.000219] pcieport 0000:00:02.0: enabling device (0140 -> 0143) <6>[ 6.006718] pcieport 0000:00:02.0: PME: Signaling with IRQ 33 <6>[ 6.013168] r8169 0000:01:00.0: enabling device (0140 -> 0143) <6>[ 6.072699] r8169 0000:01:00.0 eth0: RTL8168g/8111g, 00:04:4b:21:2a:66, XID 4c0, IRQ 404 <6>[ 6.081107] r8169 0000:01:00.0 eth0: jumbo features [frames: 9194 bytes, tx checksumming: ko] <6>[ 6.099084] +1.05V_RUN_AVDD_HDMI_PLL: supplied by +1.05V_RUN <6>[ 6.108240] drm drm: [drm] Cannot find any crtc or sizes <6>[ 6.114173] drm drm: [drm] Cannot find any crtc or sizes <6>[ 6.120770] [drm] Initialized tegra 0.0.0 20120330 for drm on minor 0 <4>[ 6.129254] tegra-ahci 70027000.sata: supply ahci not found, using dummy regulator <4>[ 6.137397] tegra-ahci 70027000.sata: supply phy not found, using dummy regulator <4>[ 6.145366] tegra-ahci 70027000.sata: supply target not found, using dummy regulator <6>[ 6.154883] tegra-ahci 70027000.sata: AHCI 0001.0301 32 slots 2 ports 3 Gbps 0x1 impl platform mode <6>[ 6.164270] tegra-ahci 70027000.sata: flags: 64bit ncq sntf pm led pmp pio slum part sadm sds apst <6>[ 6.175535] scsi host0: tegra-ahci <6>[ 6.180382] scsi host1: tegra-ahci <6>[ 6.184314] ata1: SATA max UDMA/133 mmio [mem 0x70027000-0x70028fff] port 0x100 irq 94 <6>[ 6.192551] ata2: DUMMY <6>[ 6.197239] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 696000 KHz, changing to: 714000 KHz <6>[ 6.209047] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 6.528175] ata1: SATA link down (SStatus 0 SControl 300) <4>[ 6.537102] r8169 0000:01:00.0: Direct firmware load for rtl_nic/rtl8168g-2.fw failed with error -2 <3>[ 6.546559] r8169 0000:01:00.0: Unable to load firmware rtl_nic/rtl8168g-2.fw (-2) <6>[ 6.585857] Generic FE-GE Realtek PHY r8169-0-100:00: attached PHY driver [Generic FE-GE Realtek PHY] (mii_bus:phy_addr=r8169-0-100:00, irq=IGNORE) <6>[ 6.756296] r8169 0000:01:00.0 eth0: Link is Down <6>[ 8.313667] r8169 0000:01:00.0 eth0: Link is Up - 100Mbps/Full - flow control rx/tx <6>[ 8.321886] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 8.345586] Sending DHCP requests ., OK <6>[ 8.389938] IP-Config: Got DHCP answer from 192.168.0.1, my address is 192.168.0.213 <6>[ 8.398048] IP-Config: Complete: <6>[ 8.401587] device=eth0, hwaddr=00:04:4b:21:2a:66, ipaddr=192.168.0.213, mask=255.255.255.0, gw=192.168.0.254 <6>[ 8.412313] host=192.168.0.213, domain=, nis-domain=(none) <6>[ 8.418613] bootserver=192.168.0.1, rootserver=192.168.0.1, rootpath= <6>[ 8.418636] nameserver0=192.168.0.1, nameserver1=192.168.1.254 <6>[ 8.435268] Freeing unused kernel memory: 2048K <6>[ 8.476466] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 8.548709] udevd[137]: starting version 3.2.9 <5>[ 8.554032] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.561076] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.568006] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 8.577940] udevd[137]: specified user 'tss' unknown <27>[ 8.583295] udevd[137]: specified group 'tss' unknown <30>[ 8.589851] udevd[138]: starting eudev-3.2.9 <6>[ 8.720825] tegra-wdt 60005000.timer: initialized (heartbeat = 120 sec, nowayout = 0) <6>[ 8.743176] nouveau 57000000.gpu: NVIDIA GK20A (0ea000a1) <6>[ 8.748902] nouveau 57000000.gpu: imem: using IOMMU <3>[ 8.770431] nouveau 57000000.gpu: gr ctor failed, -2 <4>[ 8.787125] nouveau: probe of 57000000.gpu failed with error -2 <27>[ 8.788690] udevd[147]: Error changing net interface name eth0 to enp1s0: Device or resource busy <28>[ 8.826748] udevd[147]: could not rename interface '3' from 'eth0' to 'enp1s0': Device or resource busy <4>[ 8.870339] tegra-xusb 70090000.usb: Direct firmware load for nvidia/tegra124/xusb.bin failed with error -2 <3>[ 8.880348] tegra-xusb 70090000.usb: failed to request firmware: -2 <3>[ 8.886876] tegra-xusb 70090000.usb: failed to request firmware: -2 <4>[ 8.921262] tegra-xusb: probe of 70090000.usb failed with error -2 <6>[ 8.929289] input: tegra-hda HDMI/DP,pcm=3 as /devices/soc0/70030000.hda/sound/card0/input1 <3>[ 8.948609] tegra-snd-rt5640 sound: snd_soc_register_card failed (-517) <4>[ 9.083942] tegra30-i2s 70301100.i2s: DMA channels sourced from device 70300000.ahub <3>[ 9.093597] tegra-snd-rt5640 sound: snd_soc_register_card failed (-517) <6>[ 9.291437] input: NVIDIA Tegra Jetson TK1 Headphones as /devices/soc0/sound/sound/card1/input2 done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / #. /lava-2318521/environment . /lava-2318521/environment / # /lava-2318521/bin/lava-test-runner /lava-2318521/0 /lava-2318521/bin/lava-test-runner /lava-2318521/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-2318521/0/tests/0_dmesg + cat uuid + UUID=2318521_1<8>[ 9.981742] .5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 10.012100] <8>[ 10.037278] <8>[ 10.060884] + set +x <8>[ 10.070471] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-2318521/environment / # . /lava-2318521/environment/lava-2318521/bin/lava-test-runner /lava-2318521/1 / # /lava-2318521/bin/lava-test-runner /lava-2318521/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-2318521/1/tests/1_bootrr + cat uuid + UUID=2<8>[ 10.553829] 318521_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/helpers:/lava-2318521/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr + sh helpers/bootrr-auto /lava-2318521/1/../bin/lava-test-case <8>[ 11.603633] /lava-2318521/1/../bin/lava-test-case <8>[ 11.636209] /lava-2318521/1/../bin/lava-test-case <8>[ 11.654284] + set +x <8>[ 11.670422] / #