Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. ser2net port 3008 device /dev/ttyimx6q-sabresd-2 [115200 N81] (Debian GNU/Linux) U-Boot 2017.03 (Jan 20 2018 - 10:43:25 +0800) CPU: Freescale i.MX6QP rev1.0 996 MHz (running at 792 MHz) CPU: Automotive temperature grade (-40C to 125C) at 26C Reset cause: POR Model: Freescale i.MX6 Quad Plus SABRE Smart Device Board Board: MX6-SabreSD DRAM: 1 GiB PMIC: PFUZE100! DEV_ID=0x10 REV_ID=0x21 MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 *** Warning - bad CRC, using default environment No panel detected: default to Hannstar-XGA Display: Hannstar-XGA (1024x768) In: serial Out: serial Err: serial flash target is MMC:1 Net: Warning: ethernet@02188000 using MAC address from ROM eth0: ethernet@02188000 [PRIME] Fastboot: Normal Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.1.205 (1344 ms) => setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 => tftp 0x12000000 1026998/tftp-deploy-3snfyutf/kernel/zImage tftp 0x12000000 1026998/tftp-deploy-3snfyutf/kernel/zImage Using ethernet@02188000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.205; sending through gateway 172.16.1.4 Filename '1026998/tftp-deploy-3snfyutf/kernel/zImage'. Load address: 0x12000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######### 9.2 MiB/s done Bytes transferred = 9667072 (938200 hex) => tftp 0x12C00000 1026998/tftp-deploy-3snfyutf/ramdisk/ramdisk.cpio.gz.uboot tftp 0x12C00000 1026998/tftp-deploy-3snfyutf/ramdisk/ramdisk.cpio.gz.uboot Using ethernet@02188000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.205; sending through gateway 172.16.1.4 Filename '1026998/tftp-deploy-3snfyutf/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x12c00000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ###################################################### 9.9 MiB/s done Bytes transferred = 16054783 (f4f9ff hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x18000000 1026998/tftp-deploy-3snfyutf/dtb/imx6q-sabresd.dtb tftp 0x18000000 1026998/tftp-deploy-3snfyutf/dtb/imx6q-sabresd.dtb Using ethernet@02188000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.205; sending through gateway 172.16.1.4 Filename '1026998/tftp-deploy-3snfyutf/dtb/imx6q-sabresd.dtb'. Load address: 0x18000000 Loading: *### 6.9 MiB/s done Bytes transferred = 43473 (a9d1 hex) => setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x12000000 0x12C00000 0x18000000 bootz 0x12000000 0x12C00000 0x18000000 Kernel image @ 0x12000000 [ 0x000000 - 0x938200 ] ## Loading init Ramdisk from Legacy Image at 12c00000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16054719 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 18000000 Booting using the fdt blob at 0x18000000 Using Device Tree in place at 18000000, end 1800d9d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.135-cip13 (KernelCI@build-j447844-arm-gcc-10-multi-v7-defconfig-wcbzm) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Aug 3 14:37:55 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Smart Device Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x02020000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 933708K/1048576K available (13312K kernel code, 2230K rwdata, 5340K rodata, 2048K init, 425K bss, 49332K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 erratum 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000008] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008444] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022341] Console: colour dummy device 80x30 <6>[ 0.024232] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034644] pid_max: default: 32768 minimum: 301 <6>[ 0.039687] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.047097] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.055734] CPU: Testing write buffer coherency: ok <6>[ 0.060211] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.065772] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.072132] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079883] rcu: Hierarchical SRCU implementation. <6>[ 0.086935] EFI services will not be available. <6>[ 0.089172] smp: Bringing up secondary CPUs ... <6>[ 0.094457] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.094466] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.105806] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.105816] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.117021] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.117030] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.127452] smp: Brought up 1 node, 4 CPUs <6>[ 0.131679] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.138136] CPU: All CPU(s) started in SVC mode. <6>[ 0.143550] devtmpfs: initialized <6>[ 0.154046] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.159373] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.169256] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.179493] pinctrl core: initialized pinctrl subsystem <6>[ 0.183885] DMI not present or invalid. <6>[ 0.187040] NET: Registered protocol family 16 <6>[ 0.193946] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.200591] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.200771] cpuidle: using governor menu <6>[ 0.208855] CPU identified as i.MX6QP, silicon rev 1.0 <6>[ 0.394726] vdd3p0: supplied by regulator-dummy <6>[ 0.810090] No ATAGs? <6>[ 0.810271] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.818052] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.828091] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.838248] Serial: AMBA PL011 UART driver <6>[ 0.869736] mxs-dma 110000.dma-apbh: initialized <6>[ 0.878160] iommu: Default domain type: Translated <6>[ 0.880850] vgaarb: loaded <5>[ 0.884240] SCSI subsystem initialized <6>[ 0.887999] usbcore: registered new interface driver usbfs <6>[ 0.893187] usbcore: registered new interface driver hub <6>[ 0.898793] usbcore: registered new device driver usb <6>[ 0.910680] i2c i2c-0: IMX I2C adapter registered <6>[ 0.922032] i2c i2c-1: IMX I2C adapter registered <6>[ 0.925793] i2c i2c-2: IMX I2C adapter registered <6>[ 0.930484] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.934322] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.943756] PTP clock support registered <6>[ 0.951583] clocksource: Switched to clocksource mxc_timer1 <6>[ 2.002179] NET: Registered protocol family 2 <6>[ 2.004309] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 2.012760] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.020244] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 2.028317] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.035755] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 2.042431] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.049129] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.056607] NET: Registered protocol family 1 <6>[ 2.061647] RPC: Registered named UNIX socket transport module. <6>[ 2.067194] RPC: Registered udp transport module. <6>[ 2.072178] RPC: Registered tcp transport module. <6>[ 2.077117] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.083844] PCI: CLS 0 bytes, default 64 <6>[ 2.088483] Trying to unpack rootfs image as initramfs... <6>[ 3.427584] Freeing initrd memory: 15680K <4>[ 3.429555] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.436787] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.446518] Initialise system trusted keyrings <6>[ 3.449745] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.462059] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.466017] NFS: Registering the id_resolver key type <5>[ 3.470642] Key type id_resolver registered <5>[ 3.475070] Key type id_legacy registered <6>[ 3.479401] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.486290] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.493979] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.498983] Key type asymmetric registered <5>[ 3.502912] Asymmetric key parser 'x509' registered <6>[ 3.508066] bounce: pool size: 64 pages <6>[ 3.512156] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 3.519765] io scheduler mq-deadline registered <6>[ 3.524567] io scheduler kyber registered <4>[ 3.553000] pwm-backlight backlight-lvds: supply power not found, using dummy regulator <4>[ 3.583836] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.590746] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 3.631100] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.639050] SuperH (H)SCI(F) driver initialized <6>[ 3.641982] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.649901] printk: console [ttymxc0] enabled <6>[ 3.649901] printk: console [ttymxc0] enabled <6>[ 3.659102] printk: bootconsole [ec_imx21] disabled <6>[ 3.659102] printk: bootconsole [ec_imx21] disabled <6>[ 3.670919] msm_serial: driver initialized <6>[ 3.676826] STMicroelectronics ASC driver initialized <6>[ 3.684030] STM32 USART driver initialized <4>[ 3.698638] panel-simple panel: supply power not found, using dummy regulator <6>[ 3.715009] brd: module loaded <6>[ 3.727541] loop: module loaded <6>[ 3.734887] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.743139] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.751412] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.759871] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.767874] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.775609] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.783172] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.793771] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.801027] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.810116] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.820782] scsi host0: ahci-imx <6>[ 3.824687] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 82 <6>[ 3.844555] CAN device driver interface <6>[ 3.849879] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.857305] pps pps0: new PPS source ptp0 <6>[ 3.912727] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.920202] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.925459] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.931720] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.937384] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.948981] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.956712] usbcore: registered new interface driver pegasus <6>[ 3.962693] usbcore: registered new interface driver asix <6>[ 3.968389] usbcore: registered new interface driver ax88179_178a <6>[ 3.974805] usbcore: registered new interface driver cdc_ether <6>[ 3.980946] usbcore: registered new interface driver smsc75xx <6>[ 3.987016] usbcore: registered new interface driver smsc95xx <6>[ 3.993077] usbcore: registered new interface driver net1080 <6>[ 3.999030] usbcore: registered new interface driver cdc_subset <6>[ 4.005268] usbcore: registered new interface driver zaurus <6>[ 4.011182] usbcore: registered new interface driver cdc_ncm <6>[ 4.020446] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 4.027262] ehci-pci: EHCI PCI platform driver <6>[ 4.032033] ehci-platform: EHCI generic platform driver <6>[ 4.037794] ehci-orion: EHCI orion driver <6>[ 4.042300] SPEAr-ehci: EHCI SPEAr driver <6>[ 4.046753] ehci-st: EHCI STMicroelectronics driver <6>[ 4.052091] ehci-exynos: EHCI Exynos driver <6>[ 4.056710] ehci-atmel: EHCI Atmel driver <6>[ 4.061147] tegra-ehci: Tegra EHCI driver <6>[ 4.065651] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.072146] ohci-pci: OHCI PCI platform driver <6>[ 4.076901] ohci-platform: OHCI generic platform driver <6>[ 4.082671] SPEAr-ohci: OHCI SPEAr driver <6>[ 4.087134] ohci-st: OHCI STMicroelectronics driver <6>[ 4.092476] ohci-atmel: OHCI Atmel driver <6>[ 4.097765] usbcore: registered new interface driver usb-storage <6>[ 4.111793] i2c /dev entries driver <6>[ 4.134965] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.141413] sdhci: Copyright(c) Pierre Ossman <6>[ 4.148620] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.156771] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.164069] sdhci-esdhc-imx 2194000.mmc: Got CD GPIO <6>[ 4.164284] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 4.169361] sdhci-esdhc-imx 2194000.mmc: Got WP GPIO <6>[ 4.174624] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 4.179935] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 4.190768] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 4.197322] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 4.200102] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 4.204788] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.218455] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 4.218565] mmc1: SDHCI controller on 2194000.mmc [2194000.mmc] using ADMA <6>[ 4.219348] usbcore: registered new interface driver usbhid <6>[ 4.219353] usbhid: USB HID core driver <4>[ 4.223420] isl29018 2-0044: No cache defaults, reading back from HW <3>[ 4.226023] isl29018 2-0044: Failed to read 1: -6 <3>[ 4.254323] isl29018 2-0044: regmap initialization fails: -6 <6>[ 4.263265] NET: Registered protocol family 10 <6>[ 4.264236] mmc2: new high speed SDHC card at address aaaa <6>[ 4.269036] Segment Routing with IPv6 <6>[ 4.277780] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.284656] NET: Registered protocol family 17 <6>[ 4.284731] mmcblk2: mmc2:aaaa SS08G 7.40 GiB <6>[ 4.289382] can: controller area network core <6>[ 4.289465] NET: Registered protocol family 29 <6>[ 4.298490] mmc3: new DDR MMC card at address 0001 <6>[ 4.298775] can: raw protocol <6>[ 4.304645] mmcblk3: mmc3:0001 Q2J55L 7.13 GiB <6>[ 4.308558] can: broadcast manager protocol <6>[ 4.312421] mmcblk3boot0: mmc3:0001 Q2J55L partition 1 2.00 MiB <6>[ 4.316630] can: netlink gateway - max_hops=1 <6>[ 4.321615] mmcblk3boot1: mmc3:0001 Q2J55L partition 2 2.00 MiB <5>[ 4.327840] Key type dns_resolver registered <6>[ 4.332088] mmcblk3rpmb: mmc3:0001 Q2J55L partition 3 4.00 MiB, chardev (235:0) <6>[ 4.343643] ThumbEE CPU extension supported. <5>[ 4.354769] Registering SWP/SWPB emulation handler <5>[ 4.360078] Loading compiled-in X.509 certificates <4>[ 4.395872] pwm-backlight backlight-lvds: supply power not found, using dummy regulator <4>[ 4.407767] panel-simple panel: supply power not found, using dummy regulator <4>[ 4.419556] imx_usb 2184200.usb: No over current polarity defined <4>[ 4.435672] pwm-backlight backlight-lvds: supply power not found, using dummy regulator <4>[ 4.447503] panel-simple panel: supply power not found, using dummy regulator <4>[ 4.459183] imx_usb 2184200.usb: No over current polarity defined <6>[ 4.469395] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.484915] pwm-backlight backlight-lvds: supply power not found, using dummy regulator <4>[ 4.496705] panel-simple panel: supply power not found, using dummy regulator <4>[ 4.508393] imx_usb 2184200.usb: No over current polarity defined <6>[ 4.602459] Qualcomm Atheros AR8031/AR8033 2188000.ethernet-1:01: attached PHY driver [Qualcomm Atheros AR8031/AR8033] (mii_bus:phy_addr=2188000.ethernet-1:01, irq=POLL) <6>[ 7.761849] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 7.769635] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.791484] Sending DHCP requests .., OK <6>[ 10.455699] IP-Config: Got DHCP answer from 172.16.1.4, my address is 172.16.1.205 <6>[ 10.463559] IP-Config: Complete: <6>[ 10.467058] device=eth0, hwaddr=00:04:9f:05:b8:b4, ipaddr=172.16.1.205, mask=255.255.255.0, gw=172.16.1.4 <6>[ 10.477339] host=172.16.1.205, domain=example.org, nis-domain=(none) <6>[ 10.484406] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 10.484412] nameserver0=172.16.1.4 <6>[ 10.499526] Freeing unused kernel memory: 2048K <6>[ 10.531978] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 10.660404] udevd[126]: starting version 3.2.9 <5>[ 10.666196] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 10.673407] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 10.680230] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 10.696035] udevd[126]: specified user 'tss' unknown <27>[ 10.701546] udevd[126]: specified group 'tss' unknown <30>[ 10.709718] udevd[127]: starting eudev-3.2.9 <6>[ 11.102306] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 11.110313] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 11.152375] pwm-backlight backlight-lvds: supply power not found, using dummy regulator <4>[ 11.182677] panel-simple panel: supply power not found, using dummy regulator <4>[ 11.195928] imx_usb 2184200.usb: No over current polarity defined <4>[ 11.218617] etnaviv-gpu 130000.gpu: deferred probe timeout, ignoring dependency <4>[ 11.226300] etnaviv-gpu: probe of 130000.gpu failed with error -110 <4>[ 11.232968] etnaviv-gpu 134000.gpu: deferred probe timeout, ignoring dependency <4>[ 11.240574] etnaviv-gpu: probe of 134000.gpu failed with error -110 <4>[ 11.247423] etnaviv-gpu 2204000.gpu: deferred probe timeout, ignoring dependency <4>[ 11.255165] etnaviv-gpu: probe of 2204000.gpu failed with error -110 <6>[ 11.264170] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 11.272839] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 11.281438] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 11.291195] caam 2100000.crypto: Entropy delay = 3200 <6>[ 11.325145] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 11.333895] dwhdmi-imx 120000.hdmi: Detected HDMI TX controller v1.30a with HDCP (DWC HDMI 3D TX PHY) <6>[ 11.357425] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 11.418186] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 11.423637] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 11.430524] caam 2100000.crypto: job rings = 2, qi = 0 <4>[ 11.459836] pwm-backlight backlight-lvds: supply power not found, using dummy regulator <6>[ 11.464031] imx-drm display-subsystem: bound 120000.hdmi (ops dw_hdmi_imx_ops [dw_hdmi_imx]) <4>[ 11.495815] panel-simple panel: supply power not found, using dummy regulator <4>[ 11.508392] imx_usb 2184200.usb: No over current polarity defined <4>[ 11.545658] ------------[ cut here ]------------ <4>[ 11.550577] WARNING: CPU: 2 PID: 131 at drivers/gpu/drm/drm_bridge.c:237 drm_encoder_cleanup+0x24/0x84 <4>[ 11.560219] Modules linked in: caam error dw_hdmi_imx(+) dw_hdmi etnaviv(+) gpu_sched imx_ldb imxdrm imx_ipu_v3 <4>[ 11.570648] CPU: 2 PID: 131 Comm: udevd Not tainted 5.10.135-cip13 #1 <4>[ 11.577356] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) <4>[ 11.584178] [] (unwind_backtrace) from [] (show_stack+0x10/0x14) <4>[ 11.592202] [] (show_stack) from [] (dump_stack+0xc0/0xd4) <4>[ 11.599701] [] (dump_stack) from [] (__warn+0xec/0x148) <4>[ 11.606942] [] (__warn) from [] (warn_slowpath_fmt+0x64/0xbc) <4>[ 11.614704] [] (warn_slowpath_fmt) from [] (drm_encoder_cleanup+0x24/0x84) <4>[ 11.623592] [] (drm_encoder_cleanup) from [] (drm_mode_config_cleanup+0x48/0x304) <4>[ 11.633089] [] (drm_mode_config_cleanup) from [] (drm_managed_release+0x80/0xd4) <4>[ 11.642495] [] (drm_managed_release) from [] (drm_dev_put+0x6c/0x78) <4>[ 11.650866] [] (drm_dev_put) from [] (imx_drm_bind+0x74/0x124 [imxdrm]) <4>[ 11.659498] [] (imx_drm_bind [imxdrm]) from [] (try_to_bring_up_master+0x160/0x1ac) <4>[ 11.669164] [] (try_to_bring_up_master) from [] (__component_add+0x98/0x13c) <4>[ 11.678221] [] (__component_add) from [] (platform_drv_probe+0x48/0x98) <4>[ 11.686848] [] (platform_drv_probe) from [] (really_probe+0xf0/0x49c) <4>[ 11.695301] [] (really_probe) from [] (driver_probe_device+0x5c/0xb4) <4>[ 11.703768] [] (driver_probe_device) from [] (device_driver_attach+0xa8/0xb0) <4>[ 11.712917] [] (device_driver_attach) from [] (__driver_attach+0x80/0x110) <4>[ 11.721801] [] (__driver_attach) from [] (bus_for_each_dev+0x78/0xb8) <4>[ 11.730252] [] (bus_for_each_dev) from [] (bus_add_driver+0xfc/0x1ec) <4>[ 11.738703] [] (bus_add_driver) from [] (driver_register+0x88/0x118) <4>[ 11.747070] [] (driver_register) from [] (do_one_initcall+0x50/0x240) <4>[ 11.755524] [] (do_one_initcall) from [] (do_init_module+0x44/0x244) <4>[ 11.763890] [] (do_init_module) from [] (sys_finit_module+0xbc/0xe8) <4>[ 11.772252] [] (sys_finit_module) from [] (ret_fast_syscall+0x0/0x54) <4>[ 11.780707] Exception stack(0xc2a4dfa8 to 0xc2a4dff0) <4>[ 11.786033] dfa0: 00020000 00000000 00000009 b6f33bc1 00000000 00058330 <4>[ 11.794478] dfc0: 00020000 00000000 00000000 0000017b 00069650 00058330 00000000 00020000 <4>[ 11.802921] dfe0: be838958 be838948 b6f2d59c b6c93830 <4>[ 11.808306] ---[ end trace 08093f8ce124a0c7 ]--- # # <4>[ 11.943650] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 11.951931] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 11.960600] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 11.968821] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <4>[ 11.990052] pwm-backlight backlight-lvds: supply power not found, using dummy regulator <4>[ 12.004586] panel-simple panel: supply power not found, using dummy regulator <4>[ 12.018633] imx_usb 2184200.usb: No over current polarity defined <6>[ 12.033275] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 12.041851] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 12.050413] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 12.058971] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 12.067735] dwhdmi-imx 120000.hdmi: Detected HDMI TX controller v1.30a with HDCP (DWC HDMI 3D TX PHY) <6>[ 12.079395] imx-drm display-subsystem: bound 120000.hdmi (ops dw_hdmi_imx_platform_driver_exit [dw_hdmi_imx]) <6>[ 12.318678] caam algorithms registered in /proc/crypto <6>[ 12.325901] caam 2100000.crypto: registering rng-caam <4>[ 12.339629] pwm-backlight backlight-lvds: supply power not found, using dummy regulator <4>[ 12.354001] panel-simple panel: supply power not found, using dummy regulator <4>[ 12.367278] imx_usb 2184200.usb: No over current polarity defined done <6>[ 12.386021] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 12.394667] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) Saving random seed: <6>[ 12.403258] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 12.413539] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <5>[ 12.414898] random: dd: uninitialized urandom read (32 bytes read) <6>[ 12.422232] dwhdmi-imx 120000.hdmi: Detected HDMI TX controller v1.30a with HDCP (DWC HDMI 3D TX PHY) OK <6>[ 12.440414] imx-drm display-subsystem: bound 120000.hdmi (ops dw_hdmi_imx_platform_driver_exit [dw_hdmi_imx]) Starting network: <4>[ 12.464618] pwm-backlight backlight-lvds: supply power not found, using dummy regulator ip: RTNETLINK answers: File exists FAIL <5>[ 12.513715] random: crng init done <5>[ 12.517418] random: 1 urandom warning(s) missed due to ratelimiting Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # # / # # / # #export SHELL=/bin/sh / # export SHELL=/bin/sh / # . /lava-1026998/environment /lava-1026998/bin/lava-test-runner /lava-1026998/0 . /lava-1026998/environment / # /lava-1026998/bin/lava-test-runner /lava-1026998/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1026998/0/tests/0_dmesg + cat uuid + UUID=1026998_1.5.2.4<8>[ 18.333311] .1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 18.380866] <8>[ 18.423762] <8>[ 18.466112] + set<8>[ 18.476161] +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-1026998/environment / # . /lava-1026998/environment/lava-1026998/bin/lava-test-runner /lava-1026998/1 / # /lava-1026998/bin/lava-test-runner /lava-1026998/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1026998/1/tests/1_bootrr + cat uuid + UUID=1026998_1.5.2<8>[ 24.206986] .4.5 + set +x + export 'PATH=/opt/bootrr/helpers:/lava-1026998/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr + sh helpers/bootrr-auto /lava-1026998/1/../bin/lava-test-case <8>[ 25.254932] /lava-1026998/1/../bin/lava-test-case <8>[ 25.295821] /lava-1026998/1/../bin/lava-test-case <8>[ 25.321406] + set<8>[ 25.340831] +x / #