connecting to NetworkSerialPort(target=Target(name='tegra124-jetson-tk1', env=None), name='USBSerialPort', state=, avail=True, host='nuc-1', port=59737, speed=115200, protocol='rfc2217') calling microcom -s 115200 -t nuc-1:59737 connected to 192.168.0.1 (port 59737) Escape character: Ctrl-\ Type the escape character to get to the prompt. U-Boot SPL 2015.10 (Dec 03 2015 - 13:25:02) U-Boot 2015.10 (Dec 03 2015 - 13:25:02 -0800) TEGRA124 Model: NVIDIA Jetson TK1 Board: NVIDIA Jetson TK1 DRAM: 2 GiB MC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 tegra-pcie: PCI regions: tegra-pcie: I/O: 0x12000000-0x12010000 tegra-pcie: non-prefetchable memory: 0x13000000-0x20000000 tegra-pcie: prefetchable memory: 0x20000000-0x40000000 tegra-pcie: 2x1, 1x1 configuration tegra-pcie: probing port 0, using 2 lanes tegra-pcie: link 0 down, retrying tegra-pcie: link 0 down, retrying tegra-pcie: link 0 down, retrying tegra-pcie: link 0 down, ignoring tegra-pcie: probing port 1, using 1 lanes In: serial Out: serial Err: serial Net: RTL8169#0 Hit any key to stop autoboot: 2  0 Tegra124 (Jetson TK1) # setenv autoload no setenv autoload no Tegra124 (Jetson TK1) # setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff Tegra124 (Jetson TK1) # setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff Tegra124 (Jetson TK1) # dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.0.213 (7 ms) Tegra124 (Jetson TK1) # setenv serverip 192.168.0.2 setenv serverip 192.168.0.2 Tegra124 (Jetson TK1) # tftp 0x81000000 2535058/tftp-deploy-5gs16gtm/kernel/zImage tftp 0x81000000 2535058/tftp-deploy-5gs16gtm/kernel/zImage Using RTL8169#0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.213 Filename '2535058/tftp-deploy-5gs16gtm/kernel/zImage'. Load address: 0x81000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######### 3 MiB/s done Bytes transferred = 9667072 (938200 hex) Tegra124 (Jetson TK1) # tftp 0x82800000 2535058/tftp-deploy-5gs16gtm/ramdisk/ramdisk.cpio.gz.uboot tftp 0x82800000 2535058/tftp-deploy-5gs16gtm/ramdisk/ramdisk.cpio.gz.uboot Using RTL8169#0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.213 Filename '2535058/tftp-deploy-5gs16gtm/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x82800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####################################################### 3 MiB/s done Bytes transferred = 16062360 (f51798 hex) Tegra124 (Jetson TK1) # setenv initrd_size ${filesize} setenv initrd_size ${filesize} Tegra124 (Jetson TK1) # tftp 0x83f80000 2535058/tftp-deploy-5gs16gtm/dtb/tegra124-jetson-tk1.dtb tftp 0x83f80000 2535058/tftp-deploy-5gs16gtm/dtb/tegra124-jetson-tk1.dtb Using RTL8169#0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.213 Filename '2535058/tftp-deploy-5gs16gtm/dtb/tegra124-jetson-tk1.dtb'. Load address: 0x83f80000 Loading: *##### 2.9 MiB/s done Bytes transferred = 66855 (10527 hex) Tegra124 (Jetson TK1) # setenv bootargs 'console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=:::::eth0:dhcp' setenv bootargs 'console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=:::::eth0:dhcp' Tegra124 (Jetson TK1) # bootz 0x81000000 0x82800000 0x83f80000 bootz 0x81000000 0x82800000 0x83f80000 Kernel image @ 0x81000000 [ 0x000000 - 0x938200 ] ## Loading init Ramdisk from Legacy Image at 82800000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16062296 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 83f80000 Booting using the fdt blob at 0x83f80000 Using Device Tree in place at 83f80000, end 83f93526 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.145-cip16 (KernelCI@build-j194467-arm-gcc-10-multi-v7-defconfig-66q45) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Fri Sep 23 17:41:39 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [413fc0f3] revision 3 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: NVIDIA Tegra124 Jetson TK1 [ 0.000000] earlycon: uart0 at MMIO 0x70006300 (options '115200n8') [ 0.000000] printk: bootconsole [uart0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0xfb800000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000afffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x00000000b0000000-0x00000000ffefffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000ffefffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000000ffefffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522496 [ 0.000000] Kernel command line: console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=:::::eth0:dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 1972980K/2096128K available (13312K kernel code, 2230K rwdata, 5344K rodata, 2048K init, 424K bss, 57612K reserved, 65536K cma-reserved, 1244160K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] /interrupt-controller@60004000: 160 interrupts forwarded to /interrupt-controller@50041000 <6>[ 0.000011] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483647500ns <6>[ 0.008952] clocksource: timer_us: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275 ns <6>[ 0.019147] Switching to timer-based delay loop, resolution 1000ns <6>[ 0.030380] clocksource: tegra_suspend_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns <6>[ 0.044056] arch_timer: cp15 timer(s) running at 12.00MHz (virt). <6>[ 0.050652] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2c47f4ee7, max_idle_ns: 440795202497 ns <6>[ 0.062112] sched_clock: 56 bits at 12MHz, resolution 83ns, wraps every 4398046511096ns <6>[ 0.070684] Switching to timer-based delay loop, resolution 83ns <6>[ 0.077752] Console: colour dummy device 80x30 <6>[ 0.082663] Calibrating delay loop (skipped), value calculated using timer frequency.. 24.00 BogoMIPS (lpj=120000) <6>[ 0.093687] pid_max: default: 32768 minimum: 301 <6>[ 0.098892] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.106758] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.115649] CPU: Testing write buffer coherency: ok <6>[ 0.121024] CPU0: Spectre v2: using ICIALLU workaround <6>[ 0.126622] CPU0: Spectre BHB: enabling loop workaround for all CPUs <3>[ 0.133691] /cpus/cpu@0 missing clock-frequency property <3>[ 0.139502] /cpus/cpu@1 missing clock-frequency property <3>[ 0.145329] /cpus/cpu@2 missing clock-frequency property <3>[ 0.151141] /cpus/cpu@3 missing clock-frequency property <6>[ 0.156932] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.163601] Setting up static identity map for 0x80300000 - 0x803000ac <6>[ 0.172633] rcu: Hierarchical SRCU implementation. <6>[ 0.181341] Tegra Revision: A01 SKU: 129 CPU Process: 1 SoC Process: 1 <6>[ 0.189198] EFI services will not be available. <6>[ 0.194408] smp: Bringing up secondary CPUs ... <6>[ 0.200019] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <3>[ 0.200027] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable <6>[ 0.217031] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <3>[ 0.217039] CPU2: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable <6>[ 0.234026] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <3>[ 0.234035] CPU3: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable <6>[ 0.250397] smp: Brought up 1 node, 4 CPUs <6>[ 0.254939] SMP: Total of 4 processors activated (96.00 BogoMIPS). <6>[ 0.261616] CPU: All CPU(s) started in SVC mode. <6>[ 0.267216] devtmpfs: initialized <6>[ 0.283680] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 <6>[ 0.292115] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.302606] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.311311] pinctrl core: initialized pinctrl subsystem <6>[ 0.318864] DMI not present or invalid. <6>[ 0.323724] NET: Registered protocol family 16 <6>[ 0.330795] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.340928] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.341593] cpuidle: using governor menu <6>[ 0.452408] No ATAGs? <6>[ 0.455181] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.463751] hw-breakpoint: maximum watchpoint size is 8 bytes. <6>[ 0.485069] Serial: AMBA PL011 UART driver <6>[ 0.491170] platform 50000000.host1x: Adding to iommu group 0 <6>[ 0.497464] platform 57000000.gpu: Adding to iommu group 1 <6>[ 0.530964] +5V_SYS: supplied by +VDD_MUX <6>[ 0.535805] +3.3V_SYS: supplied by +VDD_MUX <6>[ 0.541352] +USB0_VBUS_SW: supplied by +5V_SYS <6>[ 0.546636] +5V_USB_HS: supplied by +5V_SYS <6>[ 0.552022] +5V_HDMI_CON: supplied by +5V_SYS <6>[ 0.557224] +5V_SATA: supplied by +5V_SYS <6>[ 0.561883] reg-fixed-voltage regulator@11: nonexclusive access to GPIO for regulator@11 <6>[ 0.570743] +12V_SATA: supplied by +VDD_MUX <6>[ 0.577826] iommu: Default domain type: Translated <6>[ 0.583484] vgaarb: loaded <5>[ 0.587321] SCSI subsystem initialized <6>[ 0.591927] usbcore: registered new interface driver usbfs <6>[ 0.597961] usbcore: registered new interface driver hub <6>[ 0.603775] usbcore: registered new device driver usb <6>[ 0.610756] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.616176] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.625948] PTP clock support registered <6>[ 0.633772] clocksource: Switched to clocksource arch_sys_counter <6>[ 1.693136] NET: Registered protocol family 2 <6>[ 1.698146] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.707252] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 1.716249] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 1.724641] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 1.732479] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 1.739441] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.746630] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.754381] NET: Registered protocol family 1 <6>[ 1.759639] RPC: Registered named UNIX socket transport module. <6>[ 1.766082] RPC: Registered udp transport module. <6>[ 1.771236] RPC: Registered tcp transport module. <6>[ 1.776429] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.783383] PCI: CLS 0 bytes, default 64 <6>[ 1.788080] Trying to unpack rootfs image as initramfs... <6>[ 2.944588] Freeing initrd memory: 15688K <6>[ 2.949913] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available <5>[ 2.959832] Initialise system trusted keyrings <6>[ 2.964937] workingset: timestamp_bits=30 max_order=19 bucket_order=0 <6>[ 2.978456] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 2.985475] NFS: Registering the id_resolver key type <5>[ 2.991012] Key type id_resolver registered <5>[ 2.995646] Key type id_legacy registered <6>[ 3.000177] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.007416] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.015396] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.020589] Key type asymmetric registered <5>[ 3.025127] Asymmetric key parser 'x509' registered <6>[ 3.030502] bounce: pool size: 64 pages <6>[ 3.034794] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 3.042735] io scheduler mq-deadline registered <6>[ 3.047718] io scheduler kyber registered <6>[ 3.070947] tegra-pcie 1003000.pcie: host bridge /pcie@1003000 ranges: <6>[ 3.078040] tegra-pcie 1003000.pcie: MEM 0x0001000000..0x0001001fff -> 0x0001000000 <6>[ 3.086736] tegra-pcie 1003000.pcie: IO 0x0012000000..0x001200ffff -> 0x0000000000 <6>[ 3.095435] tegra-pcie 1003000.pcie: MEM 0x0013000000..0x001fffffff -> 0x0013000000 <6>[ 3.104124] tegra-pcie 1003000.pcie: MEM 0x0020000000..0x003fffffff -> 0x0020000000 <6>[ 3.112899] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration <6>[ 3.131385] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver registered 32 channels <6>[ 3.144684] tegra-pmc 7000e400.pmc: emergency thermal reset enabled <6>[ 3.200666] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.211067] printk: console [ttyS0] disabled <6>[ 3.215873] 70006300.serial: ttyS0 at MMIO 0x70006300 (irq = 84, base_baud = 25500000) is a Tegra <6>[ 3.225396] printk: console [ttyS0] enabled <6>[ 3.225396] printk: console [ttyS0] enabled <6>[ 3.234446] printk: bootconsole [uart0] disabled <6>[ 3.234446] printk: bootconsole [uart0] disabled <6>[ 3.245638] SuperH (H)SCI(F) driver initialized <6>[ 3.251500] msm_serial: driver initialized <6>[ 3.256070] STMicroelectronics ASC driver initialized <6>[ 3.262402] 70006000.serial: ttyTHS1 at MMIO 0x70006000 (irq = 82, base_baud = 0) is a TEGRA_UART <6>[ 3.272113] 70006040.serial: ttyTHS2 at MMIO 0x70006040 (irq = 83, base_baud = 0) is a TEGRA_UART <6>[ 3.282248] STM32 USART driver initialized <6>[ 3.290090] platform 54200000.dc: Adding to iommu group 2 <6>[ 3.298360] platform 54240000.dc: Adding to iommu group 2 <6>[ 3.309058] platform 54340000.vic: Adding to iommu group 2 <4>[ 3.319196] Failed to attached device 54200000.dc to IOMMU_mapping <4>[ 3.333980] Failed to attached device 54240000.dc to IOMMU_mapping <4>[ 3.350935] Failed to attached device 54340000.vic to IOMMU_mapping <6>[ 3.368239] brd: module loaded <6>[ 3.379448] loop: module loaded <4>[ 3.386134] tegra-ahci 70027000.sata: supply ahci not found, using dummy regulator <4>[ 3.394117] tegra-ahci 70027000.sata: supply phy not found, using dummy regulator <6>[ 3.411888] spi-nor spi1.0: w25q32dw (4096 Kbytes) <6>[ 3.422341] CAN device driver interface <6>[ 3.427503] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.434679] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.439901] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.446155] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.451808] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.462405] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.470113] usbcore: registered new interface driver pegasus <6>[ 3.476087] usbcore: registered new interface driver asix <6>[ 3.481775] usbcore: registered new interface driver ax88179_178a <6>[ 3.488174] usbcore: registered new interface driver cdc_ether <6>[ 3.494324] usbcore: registered new interface driver smsc75xx <6>[ 3.500364] usbcore: registered new interface driver smsc95xx <6>[ 3.506414] usbcore: registered new interface driver net1080 <6>[ 3.512358] usbcore: registered new interface driver cdc_subset <6>[ 3.518585] usbcore: registered new interface driver zaurus <6>[ 3.524499] usbcore: registered new interface driver cdc_ncm <4>[ 3.530781] tegra-phy 7d000000.usb-phy: supply vbus not found, using dummy regulator <4>[ 3.539094] tegra-phy 7d004000.usb-phy: supply vbus not found, using dummy regulator <6>[ 3.550107] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.556912] ehci-pci: EHCI PCI platform driver <6>[ 3.561649] ehci-platform: EHCI generic platform driver <6>[ 3.567362] ehci-orion: EHCI orion driver <6>[ 3.571796] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.576232] ehci-st: EHCI STMicroelectronics driver <6>[ 3.581514] ehci-exynos: EHCI Exynos driver <6>[ 3.586118] ehci-atmel: EHCI Atmel driver <6>[ 3.590527] tegra-ehci: Tegra EHCI driver <6>[ 3.599221] tegra-ehci 7d004000.usb: EHCI Host Controller <6>[ 3.604940] tegra-ehci 7d004000.usb: new USB bus registered, assigned bus number 1 <6>[ 3.612948] tegra-ehci 7d004000.usb: irq 105, io mem 0x7d004000 <6>[ 3.643766] tegra-ehci 7d004000.usb: USB 2.0 started, EHCI 1.10 <6>[ 3.650654] hub 1-0:1.0: USB hub found <6>[ 3.654719] hub 1-0:1.0: 1 port detected <6>[ 3.661480] tegra-ehci 7d008000.usb: EHCI Host Controller <6>[ 3.667173] tegra-ehci 7d008000.usb: new USB bus registered, assigned bus number 2 <6>[ 3.675170] tegra-ehci 7d008000.usb: irq 106, io mem 0x7d008000 <6>[ 3.703766] tegra-ehci 7d008000.usb: USB 2.0 started, EHCI 1.10 <6>[ 3.710606] hub 2-0:1.0: USB hub found <6>[ 3.714670] hub 2-0:1.0: 1 port detected <6>[ 3.719292] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.725759] ohci-pci: OHCI PCI platform driver <6>[ 3.730499] ohci-platform: OHCI generic platform driver <6>[ 3.736201] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.740623] ohci-st: OHCI STMicroelectronics driver <6>[ 3.745932] ohci-atmel: OHCI Atmel driver <6>[ 3.751035] usbcore: registered new interface driver usb-storage <6>[ 3.769211] tegra_rtc 7000e000.rtc: registered as rtc1 <5>[ 3.774636] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock <6>[ 3.781689] i2c /dev entries driver <4>[ 3.792769] at24 0-0056: supply vcc not found, using dummy regulator <6>[ 3.800503] at24 0-0056: 256 byte 24c02 EEPROM, writable, 8 bytes/write <6>[ 3.813357] as3722 4-0040: AS3722 with revision 0x1 found <6>[ 3.826248] +1.35V_LP0(sd2): supplied by +5V_SYS <6>[ 3.831552] +1.35V_LP0(sd3): Bringing 0uV into 1350000-1350000uV <6>[ 3.837979] +1.35V_LP0(sd3): supplied by +5V_SYS <6>[ 3.843468] +1.05V_RUN: supplied by +5V_SYS <6>[ 3.848194] +1.8V_VDDIO: supplied by +5V_SYS <6>[ 3.854553] +1.05V_RUN_AVDD: supplied by +1.35V_LP0(sd2) <6>[ 3.861002] +1.8V_RUN_CAM: Bringing 0uV into 1800000-1800000uV <6>[ 3.867662] +1.2V_GEN_AVDD: supplied by +1.8V_VDDIO <6>[ 3.873889] +1.05V_LP0_VDD_RTC: Bringing 1100000uV into 1000000-1000000uV <6>[ 3.881067] +1.05V_LP0_VDD_RTC: supplied by +3.3V_SYS <6>[ 3.887466] +2.8V_RUN_CAM: Bringing 0uV into 2800000-2800000uV <6>[ 3.893915] +2.8V_RUN_CAM: supplied by +3.3V_SYS <6>[ 3.899030] +1.2V_RUN_CAM_FRONT: Bringing 0uV into 1200000-1200000uV <6>[ 3.906010] +1.2V_RUN_CAM_FRONT: supplied by +1.8V_VDDIO <3>[ 3.911816] +VDDIO_SDMMC3: bypassed regulator has no supply! <3>[ 3.917755] +VDDIO_SDMMC3: failed to get the current voltage: -EPROBE_DEFER <3>[ 3.925020] as3722-regulator as3722-regulator: regulator 13 register failed -517 <6>[ 3.938082] as3722-rtc as3722-rtc: registered as rtc0 <6>[ 3.943721] as3722-rtc as3722-rtc: setting system clock to 2000-01-01T00:00:17 UTC (946684817) <6>[ 3.952611] as3722-rtc as3722-rtc: RTC interrupt 388 <4>[ 3.966742] lm90 0-004c: supply vcc not found, using dummy regulator <6>[ 3.976164] hwmon hwmon0: temp1_input not attached to any thermal zone <6>[ 3.983094] hwmon hwmon0: temp2_input not attached to any thermal zone <6>[ 3.999037] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.005496] sdhci: Copyright(c) Pierre Ossman <6>[ 4.012319] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.020211] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.027398] sdhci-tegra 700b0400.mmc: Got CD GPIO <6>[ 4.032400] sdhci-tegra 700b0400.mmc: Got WP GPIO <6>[ 4.037830] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.044900] usbcore: registered new interface driver usbhid <4>[ 4.045938] mmc1: Invalid maximum block size, assuming 512 bytes <6>[ 4.050725] usbhid: USB HID core driver <6>[ 4.056636] NET: Registered protocol family 10 <6>[ 4.066602] Segment Routing with IPv6 <6>[ 4.070586] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.077347] NET: Registered protocol family 17 <6>[ 4.082057] can: controller area network core <6>[ 4.086747] NET: Registered protocol family 29 <6>[ 4.088465] mmc1: SDHCI controller on 700b0600.mmc [700b0600.mmc] using ADMA 64-bit <6>[ 4.091453] can: raw protocol <6>[ 4.102611] can: broadcast manager protocol <6>[ 4.107073] can: netlink gateway - max_hops=1 <5>[ 4.112025] Key type dns_resolver registered <6>[ 4.117737] ThumbEE CPU extension supported. <5>[ 4.122284] Registering SWP/SWPB emulation handler <5>[ 4.127679] Loading compiled-in X.509 certificates <6>[ 4.157818] +3.3V_RUN: supplied by +3.3V_SYS <6>[ 4.164346] +3.3V_LP0: supplied by +3.3V_SYS <6>[ 4.170077] +3.3V_AVDD_HDMI_AP_GATED: supplied by +3.3V_RUN <6>[ 4.173341] mmc1: new high speed MMC card at address 0001 <3>[ 4.176988] tegra-xusb-padctl 7009f000.padctl: failed to get regulators: -517 <6>[ 4.182654] mmcblk1: mmc1:0001 SEM16G 14.7 GiB <6>[ 4.191539] tegra-pcie 1003000.pcie: host bridge /pcie@1003000 ranges: <6>[ 4.194214] mmcblk1boot0: mmc1:0001 SEM16G partition 1 4.00 MiB <6>[ 4.200707] tegra-pcie 1003000.pcie: MEM 0x0001000000..0x0001001fff -> 0x0001000000 <6>[ 4.207073] mmcblk1boot1: mmc1:0001 SEM16G partition 2 4.00 MiB <6>[ 4.215234] tegra-pcie 1003000.pcie: IO 0x0012000000..0x001200ffff -> 0x0000000000 <6>[ 4.221611] mmcblk1rpmb: mmc1:0001 SEM16G partition 3 4.00 MiB, chardev (235:0) <6>[ 4.229752] tegra-pcie 1003000.pcie: MEM 0x0013000000..0x001fffffff -> 0x0013000000 <6>[ 4.242234] mmcblk1: p1 p2 p3 p4 p5 p6 p7 p8 <6>[ 4.245669] tegra-pcie 1003000.pcie: MEM 0x0020000000..0x003fffffff -> 0x0020000000 <6>[ 4.258761] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration <4>[ 4.270383] tegra-ahci 70027000.sata: supply ahci not found, using dummy regulator <4>[ 4.278421] tegra-ahci 70027000.sata: supply phy not found, using dummy regulator <4>[ 4.287949] as3722-regulator as3722-regulator: DMA mask not set <6>[ 4.298309] +1.35V_LP0(sd2): supplied by +5V_SYS <6>[ 4.303525] +1.35V_LP0(sd3): supplied by +5V_SYS <6>[ 4.308915] +1.05V_RUN: supplied by +5V_SYS <6>[ 4.313449] +1.8V_VDDIO: supplied by +5V_SYS <6>[ 4.319781] +1.05V_RUN_AVDD: supplied by +1.35V_LP0(sd2) <6>[ 4.326511] +1.8V_RUN_CAM: supplied by +3.3V_RUN <6>[ 4.331504] +1.2V_GEN_AVDD: supplied by +1.8V_VDDIO <6>[ 4.337658] +1.05V_LP0_VDD_RTC: supplied by +3.3V_SYS <6>[ 4.344127] +2.8V_RUN_CAM: supplied by +3.3V_SYS <6>[ 4.349322] +1.2V_RUN_CAM_FRONT: supplied by +1.8V_VDDIO <3>[ 4.355015] +VDDIO_SDMMC3: bypassed regulator has no supply! <3>[ 4.360934] +VDDIO_SDMMC3: failed to get the current voltage: -EPROBE_DEFER <6>[ 4.368203] +VDDIO_SDMMC3: supplied by +3.3V_RUN <6>[ 4.374238] +1.05V_RUN_CAM_REAR: Bringing 0uV into 1050000-1050000uV <6>[ 4.381541] +1.05V_RUN_CAM_REAR: supplied by +1.8V_VDDIO <6>[ 4.388006] +3.3V_RUN_TOUCH: Bringing 0uV into 2800000-2800000uV <6>[ 4.395432] +3.3V_RUN_TOUCH: supplied by +5V_SYS <6>[ 4.400922] +2.8V_RUN_CAM_AF: Bringing 0uV into 2800000-2800000uV <6>[ 4.408000] +2.8V_RUN_CAM_AF: supplied by +5V_SYS <6>[ 4.413851] +1.8V_RUN_VPP_FUSE: Bringing 0uV into 1800000-1800000uV <6>[ 4.421075] +1.8V_RUN_VPP_FUSE: supplied by +3.3V_RUN <6>[ 4.431040] sdhci-tegra 700b0400.mmc: Got CD GPIO <4>[ 4.431992] usb2-0: supply vbus not found, using dummy regulator <6>[ 4.436077] sdhci-tegra 700b0400.mmc: Got WP GPIO <4>[ 4.442647] usb2-1: supply vbus not found, using dummy regulator <4>[ 4.454304] usb3-0: supply vbus not found, using dummy regulator <4>[ 4.461143] mmc0: Invalid maximum block size, assuming 512 bytes <6>[ 4.462465] tegra-pcie 1003000.pcie: host bridge /pcie@1003000 ranges: <6>[ 4.474295] tegra-pcie 1003000.pcie: MEM 0x0001000000..0x0001001fff -> 0x0001000000 <6>[ 4.482676] tegra-pcie 1003000.pcie: IO 0x0012000000..0x001200ffff -> 0x0000000000 <6>[ 4.491088] tegra-pcie 1003000.pcie: MEM 0x0013000000..0x001fffffff -> 0x0013000000 <6>[ 4.499489] tegra-pcie 1003000.pcie: MEM 0x0020000000..0x003fffffff -> 0x0020000000 <6>[ 4.503763] mmc0: SDHCI controller on 700b0400.mmc [700b0400.mmc] using ADMA 64-bit <6>[ 4.508024] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration <6>[ 4.523933] tegra-pcie 1003000.pcie: probing port 0, using 2 lanes <6>[ 4.532412] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes <6>[ 4.859348] mmc0: new high speed SD card at address 0260 <6>[ 4.865869] mmcblk0: mmc0:0260 1232 961 MiB <6>[ 4.873000] mmcblk0: p1 p2 <6>[ 5.748180] tegra-pcie 1003000.pcie: link 0 down, ignoring <6>[ 5.758473] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 <6>[ 5.765054] pci_bus 0000:00: root bus resource [bus 00-ff] <6>[ 5.770799] pci_bus 0000:00: root bus resource [mem 0x01000000-0x01001fff] <6>[ 5.777945] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] <6>[ 5.784397] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] <6>[ 5.791528] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] <6>[ 5.799519] pci 0000:00:02.0: [10de:0e13] type 01 class 0x060400 <4>[ 5.805803] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4 may corrupt adjacent RW1C bits <6>[ 5.815759] pci 0000:00:02.0: enabling Extended Tags <6>[ 5.821058] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold <6>[ 5.832325] PCI: bus0: Fast back to back transfers disabled <6>[ 5.838178] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring <6>[ 5.846634] pci 0000:01:00.0: [10ec:8168] type 00 class 0x020000 <6>[ 5.852926] pci 0000:01:00.0: reg 0x10: [io 0x0000-0x00ff] <6>[ 5.858808] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit] <6>[ 5.865902] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] <6>[ 5.873562] pci 0000:01:00.0: supports D1 D2 <6>[ 5.878107] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold <6>[ 5.918406] PCI: bus1: Fast back to back transfers disabled <6>[ 5.924306] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 5.931216] pci 0000:00:02.0: BAR 8: assigned [mem 0x13000000-0x130fffff] <6>[ 5.938302] pci 0000:00:02.0: BAR 9: assigned [mem 0x20000000-0x200fffff 64bit pref] <6>[ 5.946317] pci 0000:00:02.0: BAR 7: assigned [io 0x1000-0x1fff] <6>[ 5.952674] pci 0000:01:00.0: BAR 4: assigned [mem 0x20000000-0x20003fff 64bit pref] <6>[ 5.960706] pci 0000:01:00.0: BAR 2: assigned [mem 0x13000000-0x13000fff 64bit] <6>[ 5.968303] pci 0000:01:00.0: BAR 0: assigned [io 0x1000-0x10ff] <6>[ 5.974674] pci 0000:00:02.0: PCI bridge to [bus 01] <6>[ 5.979900] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] <6>[ 5.986268] pci 0000:00:02.0: bridge window [mem 0x13000000-0x130fffff] <6>[ 5.993313] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref] <4>[ 6.001352] pci 0000:00:02.0: nv_msi_ht_cap_quirk didn't locate host bridge <6>[ 6.008715] pcieport 0000:00:02.0: enabling device (0140 -> 0143) <6>[ 6.015227] pcieport 0000:00:02.0: PME: Signaling with IRQ 33 <6>[ 6.021684] r8169 0000:01:00.0: enabling device (0140 -> 0143) <6>[ 6.080688] r8169 0000:01:00.0 eth0: RTL8168g/8111g, 00:04:4b:21:2a:66, XID 4c0, IRQ 404 <6>[ 6.089101] r8169 0000:01:00.0 eth0: jumbo features [frames: 9194 bytes, tx checksumming: ko] <6>[ 6.106963] +1.05V_RUN_AVDD_HDMI_PLL: supplied by +1.05V_RUN <6>[ 6.116574] drm drm: [drm] Cannot find any crtc or sizes <6>[ 6.122499] drm drm: [drm] Cannot find any crtc or sizes <6>[ 6.128982] [drm] Initialized tegra 0.0.0 20120330 for drm on minor 0 <4>[ 6.137420] tegra-ahci 70027000.sata: supply ahci not found, using dummy regulator <4>[ 6.145502] tegra-ahci 70027000.sata: supply phy not found, using dummy regulator <4>[ 6.153404] tegra-ahci 70027000.sata: supply target not found, using dummy regulator <6>[ 6.162840] tegra-ahci 70027000.sata: AHCI 0001.0301 32 slots 2 ports 3 Gbps 0x1 impl platform mode <6>[ 6.172205] tegra-ahci 70027000.sata: flags: 64bit ncq sntf pm led pmp pio slum part sadm sds apst <6>[ 6.183447] scsi host0: tegra-ahci <6>[ 6.188358] scsi host1: tegra-ahci <6>[ 6.192291] ata1: SATA max UDMA/133 mmio [mem 0x70027000-0x70028fff] port 0x100 irq 94 <6>[ 6.200520] ata2: DUMMY <6>[ 6.205369] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 696000 KHz, changing to: 714000 KHz <6>[ 6.216968] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 6.538824] ata1: SATA link down (SStatus 0 SControl 300) <4>[ 6.548118] r8169 0000:01:00.0: Direct firmware load for rtl_nic/rtl8168g-2.fw failed with error -2 <3>[ 6.557598] r8169 0000:01:00.0: Unable to load firmware rtl_nic/rtl8168g-2.fw (-2) <6>[ 6.604320] Generic FE-GE Realtek PHY r8169-0-100:00: attached PHY driver [Generic FE-GE Realtek PHY] (mii_bus:phy_addr=r8169-0-100:00, irq=IGNORE) <6>[ 6.784917] r8169 0000:01:00.0 eth0: Link is Down <6>[ 8.333626] r8169 0000:01:00.0 eth0: Link is Up - 100Mbps/Full - flow control rx/tx <6>[ 8.343905] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 8.374009] Sending DHCP requests ., OK <6>[ 8.418468] IP-Config: Got DHCP answer from 192.168.0.1, my address is 192.168.0.213 <6>[ 8.426536] IP-Config: Complete: <6>[ 8.430023] device=eth0, hwaddr=00:04:4b:21:2a:66, ipaddr=192.168.0.213, mask=255.255.255.0, gw=192.168.0.254 <6>[ 8.440639] host=192.168.0.213, domain=, nis-domain=(none) <6>[ 8.446856] bootserver=192.168.0.1, rootserver=192.168.0.1, rootpath= <6>[ 8.446862] nameserver0=192.168.0.1, nameserver1=192.168.1.254 <6>[ 8.462013] Freeing unused kernel memory: 2048K <6>[ 8.494740] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 8.571873] udevd[138]: starting version 3.2.9 <5>[ 8.577221] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.584092] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.590965] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 8.601215] udevd[138]: specified user 'tss' unknown <27>[ 8.606642] udevd[138]: specified group 'tss' unknown <30>[ 8.612876] udevd[139]: starting eudev-3.2.9 <6>[ 8.739161] tegra-wdt 60005000.timer: initialized (heartbeat = 120 sec, nowayout = 0) <27>[ 8.743177] udevd[144]: Error changing net interface name eth0 to enp1s0: Device or resource busy <28>[ 8.764169] udevd[144]: could not rename interface '3' from 'eth0' to 'enp1s0': Device or resource busy <6>[ 8.801717] nouveau 57000000.gpu: NVIDIA GK20A (0ea000a1) <6>[ 8.807450] nouveau 57000000.gpu: imem: using IOMMU <3>[ 8.818913] nouveau 57000000.gpu: gr ctor failed, -2 <4>[ 8.824355] nouveau: probe of 57000000.gpu failed with error -2 <4>[ 8.874504] tegra-xusb 70090000.usb: Direct firmware load for nvidia/tegra124/xusb.bin failed with error -2 <3>[ 8.884512] tegra-xusb 70090000.usb: failed to request firmware: -2 <3>[ 8.891028] tegra-xusb 70090000.usb: failed to request firmware: -2 <4>[ 8.902578] tegra-xusb: probe of 70090000.usb failed with error -2 <3>[ 8.945977] tegra-snd-rt5640 sound: snd_soc_register_card failed (-517) <3>[ 8.956256] tegra-snd-rt5640 sound: snd_soc_register_card failed (-517) <6>[ 8.958691] input: tegra-hda HDMI/DP,pcm=3 as /devices/soc0/70030000.hda/sound/card0/input1 <4>[ 9.102542] tegra30-i2s 70301100.i2s: DMA channels sourced from device 70300000.ahub <3>[ 9.112321] tegra-snd-rt5640 sound: snd_soc_register_card failed (-517) done Saving random seed: <6>[ 9.300384] input: NVIDIA Tegra Jetson TK1 Headphones as /devices/soc0/sound/sound/card1/input2 OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-2535058/environment . /lava-2535058/environment / # /lava-2535058/bin/lava-test-runner /lava-2535058/0 /lava-2535058/bin/lava-test-runner /lava-2535058/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-2535058/0/tests/0_dmesg + cat uuid + <8>[ 9.942295] UUID=2535058_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 9.970422] <8>[ 9.998995] <8>[ 10.025875] + set +x <8>[ 10.035386] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-2535058/environment / # . /lava-2535058/environment/lava-2535058/bin/lava-test-runner /lava-2535058/1 / # /lava-2535058/bin/lava-test-runner /lava-2535058/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-2535058/1/tests/1_bootrr + cat uuid + UUID=253<8>[ 10.523626] 5058_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/helpers:/lava-2535058/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr + sh helpers/bootrr-auto /lava-2535058/1/../bin/lava-test-case <8>[ 11.577977] /lava-2535058/1/../bin/lava-test-case <8>[ 11.609588] /lava-2535058/1/../bin/lava-test-case <8>[ 11.625705] + set +x <8>[ 11.640114] / #