[Enter `^Ec?' for help]  U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.36 (2 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 7362637/tftp-deploy-m14n92iq/kernel/zImage tftp 0x10000000 7362637/tftp-deploy-m14n92iq/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.36 Filename '7362637/tftp-deploy-m14n92iq/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######### 9.7 MiB/s done Bytes transferred = 9667072 (938200 hex) => tftp 0x14000000 7362637/tftp-deploy-m14n92iq/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 7362637/tftp-deploy-m14n92iq/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.36 Filename '7362637/tftp-deploy-m14n92iq/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################### 11 MiB/s done Bytes transferred = 12135671 (b92cf7 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 7362637/tftp-deploy-m14n92iq/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 7362637/tftp-deploy-m14n92iq/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.36 Filename '7362637/tftp-deploy-m14n92iq/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 3.4 MiB/s done Bytes transferred = 42393 (a599 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/7362637/extract-nfsrootfs-4zg_jwxc,tcp,hard console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/7362637/extract-nfsrootfs-4zg_jwxc,tcp,hard console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x938200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 12135607 Bytes = 11.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d598 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.145-cip16 (KernelCI@build-j194467-arm-gcc-10-multi-v7-defconfig-66q45) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Fri Sep 23 17:41:39 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/7362637/extract-nfsrootfs-4zg_jwxc,tcp,hard console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 937540K/1048576K available (13312K kernel code, 2230K rwdata, 5344K rodata, 2048K init, 424K bss, 45500K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008444] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022271] Console: colour dummy device 80x30 <6>[ 0.024163] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034575] pid_max: default: 32768 minimum: 301 <6>[ 0.039609] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.047027] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.055650] CPU: Testing write buffer coherency: ok <6>[ 0.060140] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.065700] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.072046] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079753] rcu: Hierarchical SRCU implementation. <6>[ 0.086769] EFI services will not be available. <6>[ 0.089001] smp: Bringing up secondary CPUs ... <6>[ 0.094278] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.094287] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.105624] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.105632] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.116834] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.116842] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.127280] smp: Brought up 1 node, 4 CPUs <6>[ 0.131511] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.137964] CPU: All CPU(s) started in SVC mode. <6>[ 0.143383] devtmpfs: initialized <6>[ 0.153661] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.158983] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.168869] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.179086] pinctrl core: initialized pinctrl subsystem <6>[ 0.183508] DMI not present or invalid. <6>[ 0.186679] NET: Registered protocol family 16 <6>[ 0.193951] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.200544] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.200740] cpuidle: using governor menu <6>[ 0.208883] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.382828] vdd1p1: supplied by regulator-dummy <6>[ 0.391758] vdd3p0: supplied by regulator-dummy <6>[ 0.400591] vdd2p5: supplied by regulator-dummy <6>[ 0.409448] vddarm: supplied by regulator-dummy <6>[ 0.418466] vddpu: supplied by regulator-dummy <6>[ 0.427100] vddsoc: supplied by regulator-dummy <6>[ 0.747185] No ATAGs? <6>[ 0.747366] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.755127] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.765248] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.775400] Serial: AMBA PL011 UART driver <6>[ 0.779565] printk: console [ramoops-1] enabled <6>[ 0.781901] pstore: Registered ramoops as persistent store backend <6>[ 0.788159] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.819503] mxs-dma 110000.dma-apbh: initialized <6>[ 0.828960] iommu: Default domain type: Translated <6>[ 0.831665] vgaarb: loaded <5>[ 0.835088] SCSI subsystem initialized <6>[ 0.838803] usbcore: registered new interface driver usbfs <6>[ 0.843999] usbcore: registered new interface driver hub <6>[ 0.849587] usbcore: registered new device driver usb <6>[ 0.856360] i2c i2c-0: IMX I2C adapter registered <6>[ 0.861133] i2c i2c-1: IMX I2C adapter registered <6>[ 0.865573] i2c i2c-2: IMX I2C adapter registered <6>[ 0.871084] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.874923] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.884358] PTP clock support registered <6>[ 0.892190] clocksource: Switched to clocksource mxc_timer1 <6>[ 1.944094] NET: Registered protocol family 2 <6>[ 1.946296] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.954759] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 1.962206] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 1.970214] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 1.977696] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 1.984383] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.991054] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.998514] NET: Registered protocol family 1 <6>[ 2.003571] RPC: Registered named UNIX socket transport module. <6>[ 2.009115] RPC: Registered udp transport module. <6>[ 2.014111] RPC: Registered tcp transport module. <6>[ 2.019030] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.025753] PCI: CLS 0 bytes, default 64 <6>[ 2.030393] Trying to unpack rootfs image as initramfs... <6>[ 2.987967] Freeing initrd memory: 11852K <4>[ 2.990002] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 2.997133] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.006961] Initialise system trusted keyrings <6>[ 3.010151] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.022314] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.026289] NFS: Registering the id_resolver key type <5>[ 3.030913] Key type id_resolver registered <5>[ 3.035327] Key type id_legacy registered <6>[ 3.039664] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.046547] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.054233] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.059243] Key type asymmetric registered <5>[ 3.063166] Asymmetric key parser 'x509' registered <6>[ 3.068324] bounce: pool size: 64 pages <6>[ 3.072418] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.080026] io scheduler mq-deadline registered <6>[ 3.084824] io scheduler kyber registered <4>[ 3.131375] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.138318] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 3.194990] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.203199] SuperH (H)SCI(F) driver initialized <6>[ 3.206121] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.215056] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 3.222946] printk: console [ttymxc1] enabled <6>[ 3.222946] printk: console [ttymxc1] enabled <6>[ 3.232100] printk: bootconsole [ec_imx21] disabled <6>[ 3.232100] printk: bootconsole [ec_imx21] disabled <6>[ 3.243781] msm_serial: driver initialized <6>[ 3.249804] STMicroelectronics ASC driver initialized <6>[ 3.257086] STM32 USART driver initialized <4>[ 3.272363] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.280269] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.287107] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.303996] brd: module loaded <6>[ 3.317290] loop: module loaded <6>[ 3.324613] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.332825] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.341100] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.349575] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.357584] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.365317] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.372910] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.383486] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.390743] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.399843] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.410659] scsi host0: ahci-imx <6>[ 3.414551] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 3.434972] CAN device driver interface <6>[ 3.440395] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.449933] pps pps0: new PPS source ptp0 <6>[ 3.472116] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.479728] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.484986] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.491233] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.496916] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.508845] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.516575] usbcore: registered new interface driver pegasus <6>[ 3.522559] usbcore: registered new interface driver asix <6>[ 3.528258] usbcore: registered new interface driver ax88179_178a <6>[ 3.534669] usbcore: registered new interface driver cdc_ether <6>[ 3.540813] usbcore: registered new interface driver smsc75xx <6>[ 3.546893] usbcore: registered new interface driver smsc95xx <6>[ 3.552956] usbcore: registered new interface driver net1080 <6>[ 3.558913] usbcore: registered new interface driver cdc_subset <6>[ 3.565146] usbcore: registered new interface driver zaurus <6>[ 3.571051] usbcore: registered new interface driver cdc_ncm <6>[ 3.580516] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.587333] ehci-pci: EHCI PCI platform driver <6>[ 3.592081] ehci-platform: EHCI generic platform driver <6>[ 3.597885] ehci-orion: EHCI orion driver <6>[ 3.602408] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.606869] ehci-st: EHCI STMicroelectronics driver <6>[ 3.612224] ehci-exynos: EHCI Exynos driver <6>[ 3.616852] ehci-atmel: EHCI Atmel driver <6>[ 3.621301] tegra-ehci: Tegra EHCI driver <6>[ 3.625833] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.632319] ohci-pci: OHCI PCI platform driver <6>[ 3.637074] ohci-platform: OHCI generic platform driver <6>[ 3.642857] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.647322] ohci-st: OHCI STMicroelectronics driver <6>[ 3.652685] ohci-atmel: OHCI Atmel driver <6>[ 3.658027] usbcore: registered new interface driver usb-storage <6>[ 3.672410] i2c /dev entries driver <6>[ 3.695623] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.702075] sdhci: Copyright(c) Pierre Ossman <6>[ 3.709428] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.717673] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.724903] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 3.729086] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 3.730179] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 3.740916] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.748269] usbcore: registered new interface driver usbhid <6>[ 3.754138] usbhid: USB HID core driver <6>[ 3.763716] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 3.764764] NET: Registered protocol family 10 <6>[ 3.769429] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 3.772390] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 3.772786] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 3.775097] Segment Routing with IPv6 <6>[ 3.780684] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 3.787930] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.813150] NET: Registered protocol family 17 <6>[ 3.817874] can: controller area network core <6>[ 3.822597] NET: Registered protocol family 29 <6>[ 3.827311] can: raw protocol <6>[ 3.830549] can: broadcast manager protocol <6>[ 3.831577] mmc2: new high speed SDHC card at address aaaa <6>[ 3.835030] can: netlink gateway - max_hops=1 <6>[ 3.841676] mmcblk2: mmc2:aaaa SL16G 14.8 GiB <5>[ 3.845891] Key type dns_resolver registered <6>[ 3.857047] ThumbEE CPU extension supported. <5>[ 3.861634] Registering SWP/SWPB emulation handler <5>[ 3.866948] Loading compiled-in X.509 certificates <4>[ 3.877320] GPT:Primary header thinks Alt. header is not at the end of the disk. <6>[ 3.877360] pstore: Using crash dump compression: deflate <4>[ 3.885070] GPT:7812499 != 31116287 <4>[ 3.885079] GPT:Alternate GPT header not at the end of the disk. <4>[ 3.900798] GPT:7812499 != 31116287 <4>[ 3.904583] GPT: Use GNU Parted to correct GPT errors. <6>[ 3.910045] mmcblk2: p1 p2 p3 <4>[ 3.912253] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.921244] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.929328] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 3.946199] imx_usb 2184200.usb: No over current polarity defined <6>[ 3.956256] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 3.961428] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 3.992194] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 3.998592] hub 1-0:1.0: USB hub found <6>[ 4.002681] hub 1-0:1.0: 1 port detected <6>[ 4.009317] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 4.025447] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.033381] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.041565] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.054666] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.062608] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.070733] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.082516] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.094901] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.102810] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.110703] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.124564] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 4.332236] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 4.533817] hub 1-1:1.0: USB hub found <6>[ 4.538040] hub 1-1:1.0: 3 ports detected <4>[ 4.548635] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.556618] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.564897] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.282671] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 7.312292] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.342238] Sending DHCP requests ., OK <6>[ 7.386435] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.36 <6>[ 7.394761] IP-Config: Complete: <6>[ 7.398280] device=eth0, hwaddr=00:19:b8:08:f1:1c, ipaddr=192.168.201.36, mask=255.255.255.0, gw=192.168.201.1 <6>[ 7.409037] host=imx6q-sabrelite-lava-cbg-6, domain=lava-rack, nis-domain=(none) <6>[ 7.417179] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 7.417192] nameserver0=192.168.201.1 <6>[ 7.436456] Freeing unused kernel memory: 2048K <6>[ 7.473289] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u1 <6>[ 8.341500] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 8.360775] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 8.371181] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.379193] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.397822] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.413484] panel-simple panel-lcd: supply power not found, using dummy regulator <6>[ 8.423392] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <4>[ 8.426463] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.431982] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <4>[ 8.444885] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.446959] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.463359] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.482559] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.490481] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.514247] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.531522] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.539549] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.553714] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.571956] caam 2100000.crypto: Entropy delay = 3200 <6>[ 8.638155] caam 2100000.crypto: Instantiated RNG4 SH0 <4>[ 8.653659] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 8.661780] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 8.670408] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 8.678493] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <6>[ 8.698917] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 8.704389] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 8.711285] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 8.718832] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 8.728540] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 8.742916] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.750105] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.757389] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.764317] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 8.771140] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 8.777587] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 8.784024] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 8.791092] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <6>[ 8.800589] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.809175] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.817745] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.826295] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.840503] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.848466] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.857189] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.876606] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.885200] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.893763] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.902312] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 9.196142] caam algorithms registered in /proc/crypto <6>[ 9.202930] caam 2100000.crypto: registering rng-caam <4>[ 9.213018] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.220975] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.240147] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 9.254131] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.262667] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.271163] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.279705] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... done. <5>[ 9.390710] random: crng init done IP-Config: eth0 hardware address 00:19:b8:08:f1:1c mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.36 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-6 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 10.186677] systemd[1]: System time before build time, advancing clock. <30>[ 10.246448] systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 10.270747] systemd[1]: Detected architecture arm. Welcome to [1mDebian GNU/Linux 11 (bullseye)[0m! <30>[ 10.314874] systemd[1]: Set hostname to . <30>[ 11.127014] systemd[1]: Queued start job for default target Graphical Interface. <28>[ 11.136559] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. <28>[ 11.149310] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) <30>[ 11.159522] systemd[1]: Created slice system-getty.slice. [[0;32m OK [0m] Created slice [0;1;39msystem-getty.slice[0m. <30>[ 11.193809] systemd[1]: Created slice system-modprobe.slice. [[0;32m OK [0m] Created slice [0;1;39msystem-modprobe.slice[0m. <30>[ 11.233513] systemd[1]: Created slice system-serial\x2dgetty.slice. [[0;32m OK [0m] Created slice [0;1;39msystem-serial\x2dgetty.slice[0m. <30>[ 11.273462] systemd[1]: Created slice User and Session Slice. [[0;32m OK [0m] Created slice [0;1;39mUser and Session Slice[0m. <30>[ 11.313046] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [[0;32m OK [0m] Started [0;1;39mDispatch Password …ts to Console Directory Watch[0m. <30>[ 11.352948] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [[0;32m OK [0m] Started [0;1;39mForward Password R…uests to Wall Directory Watch[0m. <30>[ 11.392561] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 11.404829] systemd[1]: Reached target Local Encrypted Volumes. [[0;32m OK [0m] Reached target [0;1;39mLocal Encrypted Volumes[0m. <30>[ 11.443094] systemd[1]: Reached target Paths. [[0;32m OK [0m] Reached target [0;1;39mPaths[0m. <30>[ 11.472679] systemd[1]: Reached target Remote File Systems. [[0;32m OK [0m] Reached target [0;1;39mRemote File Systems[0m. <30>[ 11.512559] systemd[1]: Reached target Slices. [[0;32m OK [0m] Reached target [0;1;39mSlices[0m. <30>[ 11.542780] systemd[1]: Reached target Swap. [[0;32m OK [0m] Reached target [0;1;39mSwap[0m. <30>[ 11.573348] systemd[1]: Listening on initctl Compatibility Named Pipe. [[0;32m OK [0m] Listening on [0;1;39minitctl Compatibility Named Pipe[0m. <30>[ 11.649970] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. <30>[ 11.659970] systemd[1]: Listening on Journal Socket (/dev/log). [[0;32m OK [0m] Listening on [0;1;39mJournal Socket (/dev/log)[0m. <30>[ 11.693814] systemd[1]: Listening on Journal Socket. [[0;32m OK [0m] Listening on [0;1;39mJournal Socket[0m. <30>[ 11.734123] systemd[1]: Listening on Network Service Netlink Socket. [[0;32m OK [0m] Listening on [0;1;39mNetwork Service Netlink Socket[0m. <30>[ 11.775622] systemd[1]: Listening on udev Control Socket. [[0;32m OK [0m] Listening on [0;1;39mudev Control Socket[0m. <30>[ 11.813691] systemd[1]: Listening on udev Kernel Socket. [[0;32m OK [0m] Listening on [0;1;39mudev Kernel Socket[0m. <30>[ 11.853726] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 11.863293] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. <30>[ 11.875824] systemd[1]: Mounting Kernel Debug File System... Mounting [0;1;39mKernel Debug File System[0m... <30>[ 11.917231] systemd[1]: Mounting Kernel Trace File System... Mounting [0;1;39mKernel Trace File System[0m... <30>[ 11.956858] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting [0;1;39mCreate list of st…odes for the current kernel[0m... <30>[ 11.995773] systemd[1]: Starting Load Kernel Module configfs... Starting [0;1;39mLoad Kernel Module configfs[0m... <30>[ 12.035856] systemd[1]: Starting Load Kernel Module drm... Starting [0;1;39mLoad Kernel Module drm[0m... <30>[ 12.075866] systemd[1]: Starting Load Kernel Module fuse... Starting [0;1;39mLoad Kernel Module fuse[0m... <30>[ 12.116084] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. <30>[ 12.129138] systemd[1]: Starting Journal Service... Starting [0;1;39mJournal Service[0m... <30>[ 12.173485] systemd[1]: Starting Load Kernel Modules... Starting [0;1;39mLoad Kernel Modules[0m... <30>[ 12.216435] systemd[1]: Starting Remount Root and Kernel File Systems... Starting [0;1;39mRemount Root and Kernel File Systems[0m... <30>[ 12.255983] systemd[1]: Starting Coldplug All udev Devices... Starting [0;1;39mColdplug All udev Devices[0m... <30>[ 12.297512] systemd[1]: Mounted Kernel Debug File System. [[0;32m OK [0m] Mounted [0;1;39mKernel Debug File System[0m. <30>[ 12.332873] systemd[1]: Mounted Kernel Trace File System. [[0;32m OK [0m] Mounted [0;1;39mKernel Trace File System[0m. <30>[ 12.373410] systemd[1]: Finished Create list of static device nodes for the current kernel. [[0;32m OK [0m] Finished [0;1;39mCreate list of st… nodes for the current kernel[0m. <30>[ 12.432550] systemd[1]: modprobe@configfs.service: Succeeded. <30>[ 12.439457] systemd[1]: Finished Load Kernel Module configfs. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Module configfs[0m. <30>[ 12.473108] systemd[1]: Started Journal Service. [[0;32m OK [0m] Started [0;1;39mJournal Service[0m. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Module drm[0m. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Module fuse[0m. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Modules[0m. [[0;32m OK [0m] Finished [0;1;39mRemount Root and Kernel File Systems[0m. Mounting [0;1;39mKernel Configuration File System[0m... Starting [0;1;39mFlush Journal to Persistent Storage[0m... Starting [0;1;39mLoad/Save Random Seed[0m... Starting [0;1;39mApply Kernel Variables[0m... <46>[ 12.744022] systemd-journald[273]: Received client request to flush runtime journal. Starting [0;1;39mCreate System Users[0m... [[0;32m OK [0m] Mounted [0;1;39mKernel Configuration File System[0m. [[0;32m OK [0m] Finished [0;1;39mLoad/Save Random Seed[0m. [[0;32m OK [0m] Finished [0;1;39mApply Kernel Variables[0m. [[0;32m OK [0m] Finished [0;1;39mCreate System Users[0m. Starting [0;1;39mCreate Static Device Nodes in /dev[0m... [[0;32m OK [0m] Finished [0;1;39mFlush Journal to Persistent Storage[0m. [[0;32m OK [0m] Finished [0;1;39mCreate Static Device Nodes in /dev[0m. [[0;32m OK [0m] Reached target [0;1;39mLocal File Systems (Pre)[0m. [[0;32m OK [0m] Reached target [0;1;39mLocal File Systems[0m. Starting [0;1;39mCreate Volatile Files and Directories[0m... Starting [0;1;39mRule-based Manage…for Device Events and Files[0m... [[0;32m OK [0m] Finished [0;1;39mColdplug All udev Devices[0m. [[0;32m OK [0m] Started [0;1;39mRule-based Manager for Device Events and Files[0m. Starting [0;1;39mNetwork Service[0m... [[0;32m OK [0m] Finished [0;1;39mCreate Volatile Files and Directories[0m. Starting [0;1;39mUpdate UTMP about System Boot/Shutdown[0m... [[0;32m OK [0m] Finished [0;1;39mUpdate UTMP about System Boot/Shutdown[0m. [[0;32m OK [0m] Reached target [0;1;39mSystem Initialization[0m. [[0;32m OK [0m] Started [0;1;39mDaily apt download activities[0m. [[0;32m OK [0m] Started [0;1;39mDaily apt upgrade and clean activities[0m. [[0;32m OK [0m] Started [0;1;39mPeriodic ext4 Onli…ata Check for All Filesystems[0m. [[0;32m OK [0m] Started [0;1;39mDiscard unused blocks once a week[0m. [[0;32m OK [0m] Started [0;1;39mDaily Cleanup of Temporary Directories[0m. [[0;32m OK [0m] Reached target [0;1;39mTimers[0m. [[0;32m OK [0m] Listening on [0;1;39mD-Bus System Message Bus Socket[0m. [[0;32m OK [0m] Reached target [0;1;39mSockets[0m. [[0;32m OK [0m] Reached target [0;1;39mBasic System[0m. [[0;32m OK [0m] Started [0;1;39mD-Bus System Message Bus[0m. Starting [0;1;39mRemove Stale Onli…t4 Metadata Check Snapshots[0m... Starting [0;1;39mUser Login Management[0m... [[0;32m OK [0m] Started [0;1;39mNetwork Service[0m. [[0;32m OK [0m] Found device [0;1;39m/dev/ttymxc1[0m. [[0;32m OK [0m] Finished [0;1;39mRemove Stale Onli…ext4 Metadata Check Snapshots[0m. [[0;32m OK [0m] Started [0;1;39mUser Login Management[0m. [[0;32m OK [0m] Reached target [0;1;39mHardware activated USB gadget[0m. [[0;32m OK [0m] Listening on [0;1;39mLoad/Save RF …itch Status /dev/rfkill Watch[0m. Starting [0;1;39mNetwork Name Resolution[0m... [[0;32m OK [0m] Started [0;1;39mNetwork Name Resolution[0m. [[0;32m OK [0m] Reached target [0;1;39mNetwork[0m. [[0;32m OK [0m] Reached target [0;1;39mHost and Network Name Lookups[0m. Starting [0;1;39mPermit User Sessions[0m... [[0;32m OK [0m] Finished [0;1;39mPermit User Sessions[0m. [[0;32m OK [0m] Started [0;1;39mGetty on tty1[0m. [[0;32m OK [0m] Started [0;1;39mSerial Getty on ttymxc1[0m. [[0;32m OK [0m] Reached target [0;1;39mLogin Prompts[0m. [[0;32m OK [0m] Reached target [0;1;39mMulti-User System[0m. [[0;32m OK [0m] Reached target [0;1;39mGraphical Interface[0m. Starting [0;1;39mUpdate UTMP about System Runlevel Changes[0m... [[0;32m OK [0m] Finished [0;1;39mUpdate UTMP about System Runlevel Changes[0m. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 5.10.145-cip16 #1 SMP Fri Sep 23 17:41:39 UTC 2022 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/7362637/extract-nfsrootfs-4zg_jwxc' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/7362637/extract-nfsrootfs-4zg_jwxc' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-7362637/environment . /lava-7362637/environment / # /lava-7362637/bin/lava-test-runner /lava-7362637/0 /lava-7362637/bin/lava-test-runner /lava-7362637/0 + export TESTRUN_ID=0_dmesg + cd /lava-7362637/0/tests/0_dmesg + cat uuid + UUID=7362637_1.6.2.4.1<8>[ 26.719231] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 26.829296] <8>[ 26.909269] <8>[ 26.987987] + set<8>[ 26.997596] +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-7362637/environment / # . /lava-7362637/environment/lava-7362637/bin/lava-test-runner /lava-7362637/1 / # /lava-7362637/bin/lava-test-runner /lava-7362637/1 + export TESTRUN_ID=1_bootrr + cd /lava-7362637/1/tests/1_bootrr + cat uuid + UUID=7362637_1.6.2.4.5<8>[ 27.578361] + set +x + export PATH=/opt/bootrr/helpers:/lava-7362637/1/../bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin + cd /opt/bootrr + sh helpers/bootrr-auto /lava-7362637/1/../bin/lava-test-case <8>[ 28.673830] + set<8>[ 28.728231] +x / #