Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. U-Boot SPL 2019.07 (Sep 18 2019 - 15:55:50 +0200) DRAM: 512 MiB CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 Trying to boot from MMC1 U-Boot 2019.07 (Sep 18 2019 - 15:55:50 +0200) Allwinner Technology CPU: Allwinner A10 (SUN4I) Model: Olimex A10-OLinuXino-LIME I2C: ready DRAM: 512 MiB MMC: mmc@1c0f000: 0 Loading Environment from FAT... *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: eth0: ethernet@1c0b000 starting USB... Bus usb@1c14000: USB EHCI 1.00 Bus usb@1c14400: USB OHCI 1.0 Bus usb@1c1c000: USB EHCI 1.00 Bus usb@1c1c400: USB OHCI 1.0 scanning bus usb@1c14000 for devices... 1 USB Device(s) found scanning bus usb@1c14400 for devices... 1 USB Device(s) found scanning bus usb@1c1c000 for devices... 1 USB Device(s) found scanning bus usb@1c1c400 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp ENET Speed is 100 Mbps - FULL duplex connection BOOTP broadcast 1 DHCP client bound to address 10.201.4.69 (10 ms) => setenv serverip 10.201.1.8 setenv serverip 10.201.1.8 => tftp 0x40000000 2534951/tftp-deploy-cmbp5z94/kernel/zImage tftp 0x40000000 2534951/tftp-deploy-cmbp5z94/kernel/zImage Using ethernet@1c0b000 device TFTP from server 10.201.1.8; our IP address is 10.201.4.69 Filename '2534951/tftp-deploy-cmbp5z94/kernel/zImage'. Load address: 0x40000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################## 944.3 KiB/s done Bytes transferred = 4833192 (49bfa8 hex) => tftp 0x44300000 2534951/tftp-deploy-cmbp5z94/ramdisk/ramdisk.cpio.gz.uboot tftp 0x44300000 2534951/tftp-deploy-cmbp5z94/ramdisk/ramdisk.cpio.gz.uboot Using ethernet@1c0b000 device TFTP from server 10.201.1.8; our IP address is 10.201.4.69 Filename '2534951/tftp-deploy-cmbp5z94/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x44300000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################ 947.3 KiB/s done Bytes transferred = 7959119 (79724f hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x44000000 2534951/tftp-deploy-cmbp5z94/dtb/sun4i-a10-olinuxino-lime.dtb tftp 0x44000000 2534951/tftp-deploy-cmbp5z94/dtb/sun4i-a10-olinuxino-lime.dtb Using ethernet@1c0b000 device TFTP from server 10.201.1.8; our IP address is 10.201.4.69 Filename '2534951/tftp-deploy-cmbp5z94/dtb/sun4i-a10-olinuxino-lime.dtb'. Load address: 0x44000000 Loading: *##### 803.7 KiB/s done Bytes transferred = 22240 (56e0 hex) => setenv bootargs 'console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x40000000 0x44300000 0x44000000 bootz 0x40000000 0x44300000 0x44000000 ## Loading init Ramdisk from Legacy Image at 44300000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 7959055 Bytes = 7.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 44000000 Booting using the fdt blob at 0x44000000 EHCI failed to shut down host controller. Using Device Tree in place at 44000000, end 440086df Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.145-cip16 (KernelCI@build-j194486-arm-gcc-10-sunxi-defconfig-zt9zz) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Fri Sep 23 17:41:09 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Olimex A10-OLinuXino-LIME [ 0.000000] earlycon: uart0 at MMIO32 0x01c28000 (options '115200n8') [ 0.000000] printk: bootconsole [uart0] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Reserved memory: created CMA memory pool at 0x4a000000, size 96 MiB [ 0.000000] OF: reserved mem: initialized node default-pool, compatible id shared-dma-pool [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000040000000-0x000000005fffffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x000000005fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000005fffffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] percpu: Embedded 15 pages/cpu s31180 r8192 d22068 u61440 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 400896K/524288K available (7168K kernel code, 904K rwdata, 1948K rodata, 1024K init, 272K bss, 25088K reserved, 98304K cma-reserved, 0K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000020] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008122] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.017957] Console: colour dummy device 80x30 <6>[ 0.022705] Calibrating delay loop... 910.13 BogoMIPS (lpj=4550656) <6>[ 0.114130] pid_max: default: 32768 minimum: 301 <6>[ 0.119172] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.126748] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.135430] CPU: Testing write buffer coherency: ok <3>[ 0.140645] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable <6>[ 0.150652] CPU0: thread -1, cpu 0, socket -1, mpidr 0 <6>[ 0.156725] Setting up static identity map for 0x40100000 - 0x40100060 <6>[ 0.163737] rcu: Hierarchical SRCU implementation. <6>[ 0.169291] smp: Bringing up secondary CPUs ... <6>[ 0.174104] smp: Brought up 1 node, 1 CPU <6>[ 0.178409] SMP: Total of 1 processors activated (910.13 BogoMIPS). <6>[ 0.184945] CPU: All CPU(s) started in SVC mode. <6>[ 0.190294] devtmpfs: initialized <6>[ 0.198776] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.206945] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.217086] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.228794] pinctrl core: initialized pinctrl subsystem <6>[ 0.235718] NET: Registered protocol family 16 <6>[ 0.242104] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.250064] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.250302] hw-breakpoint: debug architecture 0x4 unsupported. <5>[ 0.284874] SCSI subsystem initialized <6>[ 0.289504] usbcore: registered new interface driver usbfs <6>[ 0.295318] usbcore: registered new interface driver hub <6>[ 0.301003] usbcore: registered new device driver usb <6>[ 0.306528] mc: Linux media interface: v0.10 <6>[ 0.311125] videodev: Linux video capture interface: v2.00 <6>[ 0.316978] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.322238] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.331656] PTP clock support registered <6>[ 0.336465] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.343763] clocksource: Switched to clocksource timer <6>[ 0.357073] NET: Registered protocol family 2 <6>[ 0.361976] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.370178] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 0.378862] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 0.387122] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 0.394774] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 0.401650] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 0.408480] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 0.415862] NET: Registered protocol family 1 <6>[ 0.421200] RPC: Registered named UNIX socket transport module. <6>[ 0.427448] RPC: Registered udp transport module. <6>[ 0.432417] RPC: Registered tcp transport module. <6>[ 0.437404] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.444413] Unpacking initramfs... <6>[ 0.963666] Freeing initrd memory: 7776K <6>[ 0.968394] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available <6>[ 0.978163] workingset: timestamp_bits=30 max_order=17 bucket_order=0 <5>[ 0.991204] NFS: Registering the id_resolver key type <5>[ 0.996647] Key type id_resolver registered <5>[ 1.001097] Key type id_legacy registered <6>[ 1.005486] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 1.013171] io scheduler mq-deadline registered <6>[ 1.017990] io scheduler kyber registered <3>[ 1.022913] sun4i-usb-phy 1c13400.phy: Couldn't request ID GPIO <6>[ 1.032441] sun4i-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver <6>[ 1.094177] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled <4>[ 1.102720] sun4i-pinctrl 1c20800.pinctrl: supply vcc-pb not found, using dummy regulator <6>[ 1.112192] printk: console [ttyS0] disabled <6>[ 1.136971] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 39, base_baud = 1500000) is a U6_16550A <6>[ 1.146278] printk: console [ttyS0] enabled <6>[ 1.146278] printk: console [ttyS0] enabled <6>[ 1.155183] printk: bootconsole [uart0] disabled <6>[ 1.155183] printk: bootconsole [uart0] disabled <6>[ 1.169325] sun4i-drm display-engine: bound 1e00000.display-frontend (ops 0xc084c7d8) <6>[ 1.177628] sun4i-drm display-engine: bound 1e20000.display-frontend (ops 0xc084c7d8) <6>[ 1.186107] sun4i-drm display-engine: bound 1e60000.display-backend (ops 0xc084bf78) <3>[ 1.194140] sun4i-drm display-engine: attempt to add DMA range to existing map <6>[ 1.201945] sun4i-drm display-engine: bound 1e40000.display-backend (ops 0xc084bf78) <6>[ 1.210394] sun4i-drm display-engine: No panel or bridge found... RGB output disabled <6>[ 1.218530] sun4i-drm display-engine: bound 1c0c000.lcd-controller (ops 0xc084a8d8) <6>[ 1.226832] sun4i-drm display-engine: No panel or bridge found... RGB output disabled <6>[ 1.234960] sun4i-drm display-engine: bound 1c0d000.lcd-controller (ops 0xc084a8d8) <6>[ 1.244316] sun4i-drm display-engine: bound 1c16000.hdmi (ops 0xc084cef8) <6>[ 1.252081] [drm] Initialized sun4i-drm 1.0.0 20150629 for display-engine on minor 0 <6>[ 1.260205] sun4i-drm display-engine: [drm] Cannot find any crtc or sizes <6>[ 1.271548] lima 1c40000.gpu: gp - mali400 version major 1 minor 1 <6>[ 1.278120] lima 1c40000.gpu: pp0 - mali400 version major 1 minor 1 <6>[ 1.284715] lima 1c40000.gpu: l2 cache 32K, 4-way, 64byte cache line, 64bit external bus <6>[ 1.293597] lima 1c40000.gpu: bus rate = 152000000 <6>[ 1.298704] lima 1c40000.gpu: mod rate = 384000000 <6>[ 1.304245] [drm] Initialized lima 1.1.0 20191231 for 1c40000.gpu on minor 1 <4>[ 1.312281] ahci-sunxi 1c18000.sata: supply ahci not found, using dummy regulator <4>[ 1.320251] ahci-sunxi 1c18000.sata: supply phy not found, using dummy regulator <4>[ 1.329647] sun4i-mdio 1c0b080.mdio: supply phy not found, using dummy regulator <6>[ 1.401096] CAN device driver interface <4>[ 1.405658] sun4i-pinctrl 1c20800.pinctrl: supply vcc-pa not found, using dummy regulator <6>[ 1.416287] sun4i-emac 1c0b000.ethernet: eth0: at (ptrval), IRQ 19 MAC: 02:49:09:40:ab:3d <6>[ 1.425643] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 1.432433] ehci-platform: EHCI generic platform driver <6>[ 1.438491] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 1.445012] ohci-platform: OHCI generic platform driver <6>[ 1.452684] sunxi-rtc 1c20d00.rtc: registered as rtc0 <6>[ 1.458172] sunxi-rtc 1c20d00.rtc: setting system clock to 2010-01-01T00:00:27 UTC (1262304027) <6>[ 1.467283] i2c /dev entries driver <6>[ 1.472105] axp20x-i2c 1-0034: AXP20x variant AXP209 found <4>[ 1.484134] axp20x-gpio: Failed to locate of_node [id: -1] <6>[ 1.490364] input: axp20x-pek as /devices/platform/soc/1c2ac00.i2c/i2c-1/1-0034/axp20x-pek/input/input0 <4>[ 1.508463] axp20x-regulator axp20x-regulator: regulators node not found <6>[ 1.515641] ldo1: supplied by regulator-dummy <6>[ 1.520928] ldo2: supplied by regulator-dummy <6>[ 1.526227] ldo3: supplied by regulator-dummy <6>[ 1.531033] ldo4: supplied by regulator-dummy <6>[ 1.536311] ldo5: supplied by regulator-dummy <6>[ 1.541551] dcdc2: supplied by regulator-dummy <6>[ 1.546895] dcdc3: supplied by regulator-dummy <4>[ 1.551686] axp20x-adc: Failed to locate of_node [id: -1] <4>[ 1.557544] axp20x-battery-power-supply: Failed to locate of_node [id: -1] <4>[ 1.564824] axp20x-ac-power-supply: Failed to locate of_node [id: -1] <4>[ 1.571620] axp20x-usb-power-supply: Failed to locate of_node [id: -1] <6>[ 1.578540] axp20x-i2c 1-0034: AXP20X driver loaded <6>[ 1.586893] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0) <4>[ 1.596868] sun4i-pinctrl 1c20800.pinctrl: supply vcc-ph not found, using dummy regulator <6>[ 1.606127] sun4i-ss 1c15000.crypto-engine: Die ID 7 <4>[ 1.611716] sun4i-pinctrl 1c20800.pinctrl: supply vcc-pf not found, using dummy regulator <6>[ 1.621344] sunxi-mmc 1c0f000.mmc: Got CD GPIO <6>[ 1.628587] usbcore: registered new interface driver usbhid <6>[ 1.634509] usbhid: USB HID core driver <6>[ 1.639300] cedrus 1c0e000.video-codec: Device registered as /dev/video0 <6>[ 1.651493] NET: Registered protocol family 17 <6>[ 1.656383] can: controller area network core <6>[ 1.661086] NET: Registered protocol family 29 <6>[ 1.665824] can: raw protocol <6>[ 1.669058] can: broadcast manager protocol <6>[ 1.673507] can: netlink gateway - max_hops=1 <5>[ 1.678385] Key type dns_resolver registered <5>[ 1.682985] Registering SWP/SWPB emulation handler <4>[ 1.702415] sun4i-pinctrl 1c20800.pinctrl: supply vcc-pc not found, using dummy regulator <4>[ 1.714301] ahci-sunxi 1c18000.sata: supply ahci not found, using dummy regulator <4>[ 1.722240] ahci-sunxi 1c18000.sata: supply phy not found, using dummy regulator <6>[ 1.730694] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 2048 KB <4>[ 1.771752] mmc0: host does not support reading read-only switch, assuming write-enable <6>[ 1.782933] mmc0: new high speed SDHC card at address 0007 <6>[ 1.789676] mmcblk0: mmc0:0007 SD16G 14.5 GiB <6>[ 1.798953] mmcblk0: p1 <6>[ 1.823823] ahci-sunxi 1c18000.sata: controller can't do PMP, turning off CAP_PMP <4>[ 1.831576] ahci-sunxi 1c18000.sata: forcing PORTS_IMPL to 0x1 <6>[ 1.837770] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 1.847017] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc <6>[ 1.856438] scsi host0: ahci-sunxi <6>[ 1.860473] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 29 <6>[ 1.869687] ehci-platform 1c14000.usb: EHCI Host Controller <6>[ 1.875607] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1 <6>[ 1.885040] ehci-platform 1c14000.usb: irq 25, io mem 0x01c14000 <6>[ 1.914601] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00 <6>[ 1.921842] hub 1-0:1.0: USB hub found <6>[ 1.925980] hub 1-0:1.0: 1 port detected <6>[ 1.931431] ehci-platform 1c1c000.usb: EHCI Host Controller <6>[ 1.937385] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2 <6>[ 1.945762] ehci-platform 1c1c000.usb: irq 30, io mem 0x01c1c000 <6>[ 1.973793] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 <6>[ 1.980934] hub 2-0:1.0: USB hub found <6>[ 1.985905] hub 2-0:1.0: 1 port detected <6>[ 1.991340] ohci-platform 1c14400.usb: Generic Platform OHCI controller <6>[ 1.998325] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 3 <6>[ 2.006698] ohci-platform 1c14400.usb: irq 26, io mem 0x01c14400 <6>[ 2.078585] hub 3-0:1.0: USB hub found <6>[ 2.082659] hub 3-0:1.0: 1 port detected <6>[ 2.088167] ohci-platform 1c1c400.usb: Generic Platform OHCI controller <6>[ 2.095151] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4 <6>[ 2.103499] ohci-platform 1c1c400.usb: irq 31, io mem 0x01c1c400 <6>[ 2.178881] hub 4-0:1.0: USB hub found <6>[ 2.183017] hub 4-0:1.0: 1 port detected <4>[ 2.189812] usb_phy_generic usb_phy_generic.0.auto: supply vcc not found, using dummy regulator <4>[ 2.199046] usb_phy_generic usb_phy_generic.0.auto: dummy supplies not allowed for exclusive requests <6>[ 2.209320] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver <6>[ 2.215407] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 5 <6>[ 2.223594] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 2.230377] hub 5-0:1.0: USB hub found <6>[ 2.234527] hub 5-0:1.0: 1 port detected <6>[ 2.503819] sun4i-emac 1c0b000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <5>[ 2.563779] Sending DHCP requests ., OK <6>[ 2.607898] IP-Config: Got DHCP answer from 10.201.1.3, my address is 10.201.4.69 <6>[ 2.615674] IP-Config: Complete: <6>[ 2.619174] device=eth0, hwaddr=02:49:09:40:ab:3d, ipaddr=10.201.4.69, mask=255.255.0.0, gw=10.201.1.3 <6>[ 2.629193] host=10.201.4.69, domain=, nis-domain=(none) <6>[ 2.635220] bootserver=10.201.1.3, rootserver=10.201.1.3, rootpath= <6>[ 2.635230] nameserver0=10.1.1.1 <6>[ 2.646733] ALSA device list: <6>[ 2.649977] No soundcards found. <6>[ 2.656871] Freeing unused kernel memory: 1024K <6>[ 2.674258] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 2.848242] udevd[99]: starting version 3.2.9 <5>[ 2.854728] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 2.861809] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 2.869123] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 2.885334] udevd[99]: specified user 'tss' unknown <27>[ 2.890741] udevd[99]: specified group 'tss' unknown <30>[ 2.905470] udevd[100]: starting eudev-3.2.9 done Saving random seed: <5>[ 4.378241] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 4.476583] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-2534951/environment . /lava-2534951/environment / # /lava-2534951/bin/lava-test-runner /lava-2534951/0 /lava-2534951/bin/lava-test-runner /lava-2534951/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-2534951/0/tests/0_dmesg + cat uuid + UUID=2534951_1.5.2.4.1 + set +x <8>[ 5.175948] + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 5.227951] <8>[ 5.274707] <8>[ 5.321078] + set +x <8>[ 5.331565] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-2534951/environment / # . /lava-2534951/environment/lava-2534951/bin/lava-test-runner /lava-2534951/1 / # /lava-2534951/bin/lava-test-runner /lava-2534951/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-2534951/1/tests/1_bootrr + cat uuid <8>[ 5.899793] + UUID=2534951_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/helpers:/lava-2534951/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr + sh helpers/bootrr-auto /lava-2534951/1/../bin/lava-test-case <8>[ 6.951860] /lava-2534951/1/../bin/lava-test-case <8>[ 7.001497] /lava-2534951/1/../bin/lava-test-case <8>[ 7.029475] + set +x <8>[ 7.050273] / #