[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.35 (3 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 7724746/tftp-deploy-dt_7124q/kernel/zImage tftp 0x10000000 7724746/tftp-deploy-dt_7124q/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '7724746/tftp-deploy-dt_7124q/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######### 11.8 MiB/s done Bytes transferred = 9667072 (938200 hex) => tftp 0x14000000 7724746/tftp-deploy-dt_7124q/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 7724746/tftp-deploy-dt_7124q/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '7724746/tftp-deploy-dt_7124q/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####################################################### 12.2 MiB/s done Bytes transferred = 16060921 (f511f9 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 7724746/tftp-deploy-dt_7124q/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 7724746/tftp-deploy-dt_7124q/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '7724746/tftp-deploy-dt_7124q/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 3.4 MiB/s done Bytes transferred = 42393 (a599 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x938200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16060857 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d598 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.147-cip18 (KernelCI@build-j387169-arm-gcc-10-multi-v7-defconfig-h9gmq) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Oct 26 09:46:45 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 933704K/1048576K available (13312K kernel code, 2230K rwdata, 5344K rodata, 2048K init, 424K bss, 49336K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008443] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022214] Console: colour dummy device 80x30 <6>[ 0.024104] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034518] pid_max: default: 32768 minimum: 301 <6>[ 0.039553] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.046969] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.055582] CPU: Testing write buffer coherency: ok <6>[ 0.060084] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.065645] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.071983] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079685] rcu: Hierarchical SRCU implementation. <6>[ 0.086635] EFI services will not be available. <6>[ 0.088863] smp: Bringing up secondary CPUs ... <6>[ 0.094131] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.094140] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.105479] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.105488] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.116689] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.116697] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.127152] smp: Brought up 1 node, 4 CPUs <6>[ 0.131378] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.137839] CPU: All CPU(s) started in SVC mode. <6>[ 0.143258] devtmpfs: initialized <6>[ 0.153544] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.158880] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.168756] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.178953] pinctrl core: initialized pinctrl subsystem <6>[ 0.183343] DMI not present or invalid. <6>[ 0.186546] NET: Registered protocol family 16 <6>[ 0.193800] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.200373] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.200558] cpuidle: using governor menu <6>[ 0.208709] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.382074] vdd1p1: supplied by regulator-dummy <6>[ 0.390988] vdd3p0: supplied by regulator-dummy <6>[ 0.399823] vdd2p5: supplied by regulator-dummy <6>[ 0.408648] vddarm: supplied by regulator-dummy <6>[ 0.417659] vddpu: supplied by regulator-dummy <6>[ 0.426246] vddsoc: supplied by regulator-dummy <6>[ 0.744785] No ATAGs? <6>[ 0.744970] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.752748] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.762869] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.773025] Serial: AMBA PL011 UART driver <6>[ 0.777181] printk: console [ramoops-1] enabled <6>[ 0.779527] pstore: Registered ramoops as persistent store backend <6>[ 0.785778] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.817074] mxs-dma 110000.dma-apbh: initialized <6>[ 0.826624] iommu: Default domain type: Translated <6>[ 0.829346] vgaarb: loaded <5>[ 0.832734] SCSI subsystem initialized <6>[ 0.836494] usbcore: registered new interface driver usbfs <6>[ 0.841663] usbcore: registered new interface driver hub <6>[ 0.847244] usbcore: registered new device driver usb <6>[ 0.854003] i2c i2c-0: IMX I2C adapter registered <6>[ 0.858818] i2c i2c-1: IMX I2C adapter registered <6>[ 0.863214] i2c i2c-2: IMX I2C adapter registered <6>[ 0.868727] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.872586] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.882019] PTP clock support registered <6>[ 0.889659] clocksource: Switched to clocksource mxc_timer1 <6>[ 1.943918] NET: Registered protocol family 2 <6>[ 1.946113] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.954548] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 1.962012] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 1.970066] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 1.977499] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 1.984216] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.990919] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.998319] NET: Registered protocol family 1 <6>[ 2.003389] RPC: Registered named UNIX socket transport module. <6>[ 2.008937] RPC: Registered udp transport module. <6>[ 2.013932] RPC: Registered tcp transport module. <6>[ 2.018854] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.025580] PCI: CLS 0 bytes, default 64 <6>[ 2.030244] Trying to unpack rootfs image as initramfs... <6>[ 3.371015] Freeing initrd memory: 15688K <4>[ 3.372900] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.380178] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.390069] Initialise system trusted keyrings <6>[ 3.393196] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.405356] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.409322] NFS: Registering the id_resolver key type <5>[ 3.413964] Key type id_resolver registered <5>[ 3.418344] Key type id_legacy registered <6>[ 3.422720] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.429568] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.437268] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.442336] Key type asymmetric registered <5>[ 3.446186] Asymmetric key parser 'x509' registered <6>[ 3.451382] bounce: pool size: 64 pages <6>[ 3.455439] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.463083] io scheduler mq-deadline registered <6>[ 3.467848] io scheduler kyber registered <4>[ 3.514177] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.521120] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 3.582987] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.591151] SuperH (H)SCI(F) driver initialized <6>[ 3.594072] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.602992] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 3.610904] printk: console [ttymxc1] enabled <6>[ 3.610904] printk: console [ttymxc1] enabled <6>[ 3.620067] printk: bootconsole [ec_imx21] disabled <6>[ 3.620067] printk: bootconsole [ec_imx21] disabled <6>[ 3.631687] msm_serial: driver initialized <6>[ 3.637762] STMicroelectronics ASC driver initialized <6>[ 3.645048] STM32 USART driver initialized <4>[ 3.660350] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.668266] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.675051] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.691868] brd: module loaded <6>[ 3.705101] loop: module loaded <6>[ 3.712485] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.720699] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.728975] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.737439] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.745457] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.753194] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.760785] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.771368] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.778623] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.787726] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.798514] scsi host0: ahci-imx <6>[ 3.802412] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 3.822788] CAN device driver interface <6>[ 3.828201] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.837720] pps pps0: new PPS source ptp0 <6>[ 3.874544] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.882135] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.887370] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.893647] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.899314] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.911215] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.918920] usbcore: registered new interface driver pegasus <6>[ 3.924920] usbcore: registered new interface driver asix <6>[ 3.930638] usbcore: registered new interface driver ax88179_178a <6>[ 3.937032] usbcore: registered new interface driver cdc_ether <6>[ 3.943190] usbcore: registered new interface driver smsc75xx <6>[ 3.949243] usbcore: registered new interface driver smsc95xx <6>[ 3.955304] usbcore: registered new interface driver net1080 <6>[ 3.961283] usbcore: registered new interface driver cdc_subset <6>[ 3.967501] usbcore: registered new interface driver zaurus <6>[ 3.973426] usbcore: registered new interface driver cdc_ncm <6>[ 3.982874] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.989691] ehci-pci: EHCI PCI platform driver <6>[ 3.994444] ehci-platform: EHCI generic platform driver <6>[ 4.000254] ehci-orion: EHCI orion driver <6>[ 4.004744] SPEAr-ehci: EHCI SPEAr driver <6>[ 4.009201] ehci-st: EHCI STMicroelectronics driver <6>[ 4.014557] ehci-exynos: EHCI Exynos driver <6>[ 4.019182] ehci-atmel: EHCI Atmel driver <6>[ 4.023655] tegra-ehci: Tegra EHCI driver <6>[ 4.028141] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.034623] ohci-pci: OHCI PCI platform driver <6>[ 4.039373] ohci-platform: OHCI generic platform driver <6>[ 4.045147] SPEAr-ohci: OHCI SPEAr driver <6>[ 4.049633] ohci-st: OHCI STMicroelectronics driver <6>[ 4.054973] ohci-atmel: OHCI Atmel driver <6>[ 4.060343] usbcore: registered new interface driver usb-storage <6>[ 4.074705] i2c /dev entries driver <6>[ 4.097952] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.104433] sdhci: Copyright(c) Pierre Ossman <6>[ 4.111791] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.120044] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.127268] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 4.131475] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 4.132561] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 4.141172] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 4.143203] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.148671] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 4.155956] usbcore: registered new interface driver usbhid <6>[ 4.161488] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 4.167322] usbhid: USB HID core driver <6>[ 4.174642] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 4.175091] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 4.185397] NET: Registered protocol family 10 <6>[ 4.198863] Segment Routing with IPv6 <6>[ 4.202912] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.209691] NET: Registered protocol family 17 <6>[ 4.214414] can: controller area network core <6>[ 4.219105] NET: Registered protocol family 29 <6>[ 4.220742] mmc2: new high speed SDHC card at address 0001 <6>[ 4.223846] can: raw protocol <6>[ 4.230465] mmcblk2: mmc2:0001 SD 14.6 GiB <6>[ 4.232830] can: broadcast manager protocol <6>[ 4.241741] can: netlink gateway - max_hops=1 <5>[ 4.246897] Key type dns_resolver registered <4>[ 4.250486] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 4.259106] GPT:29296874 != 30560255 <6>[ 4.261094] ThumbEE CPU extension supported. <4>[ 4.262984] GPT:Alternate GPT header not at the end of the disk. <5>[ 4.267492] Registering SWP/SWPB emulation handler <4>[ 4.273766] GPT:29296874 != 30560255 <4>[ 4.273769] GPT: Use GNU Parted to correct GPT errors. <6>[ 4.273823] mmcblk2: p1 p2 p3 <5>[ 4.282845] Loading compiled-in X.509 certificates <6>[ 4.301688] pstore: Using crash dump compression: deflate <4>[ 4.329163] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.337124] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.345081] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.361256] imx_usb 2184200.usb: No over current polarity defined <6>[ 4.371287] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 4.376461] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 4.409793] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 4.416914] hub 1-0:1.0: USB hub found <6>[ 4.421063] hub 1-0:1.0: 1 port detected <6>[ 4.429708] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 4.444925] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.452848] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.460755] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.472890] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.480816] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.488640] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.498623] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.510878] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.518752] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.526679] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.540949] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 4.749698] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 4.951348] hub 1-1:1.0: USB hub found <6>[ 4.955567] hub 1-1:1.0: 3 ports detected <4>[ 4.970078] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.978122] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.987968] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 5.279684] usb 1-1.1: new low-speed USB device number 3 using ci_hdrc <6>[ 5.448457] input: Lite-On Technology Corp. ThinkPad USB Keyboard with TrackPoint as /devices/platform/soc/2100000.bus/2184200.usb/ci_hdrc.1/usb1/1-1/1-1.1/1-1.1:1.0/0003:17EF:6009.0001/input/input1 <6>[ 5.530525] hid-generic 0003:17EF:6009.0001: input: USB HID v1.10 Keyboard [Lite-On Technology Corp. ThinkPad USB Keyboard with TrackPoint] on usb-ci_hdrc.1-1.1/input0 <4>[ 5.555030] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 5.563136] panel-simple panel-lcd: Specify missing connector_type <4>[ 5.572974] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 5.589249] input: Lite-On Technology Corp. ThinkPad USB Keyboard with TrackPoint Mouse as /devices/platform/soc/2100000.bus/2184200.usb/ci_hdrc.1/usb1/1-1/1-1.1/1-1.1:1.1/0003:17EF:6009.0002/input/input2 <6>[ 5.608098] input: Lite-On Technology Corp. ThinkPad USB Keyboard with TrackPoint System Control as /devices/platform/soc/2100000.bus/2184200.usb/ci_hdrc.1/usb1/1-1/1-1.1/1-1.1:1.1/0003:17EF:6009.0002/input/input3 <6>[ 5.690231] input: Lite-On Technology Corp. ThinkPad USB Keyboard with TrackPoint Consumer Control as /devices/platform/soc/2100000.bus/2184200.usb/ci_hdrc.1/usb1/1-1/1-1.1/1-1.1:1.1/0003:17EF:6009.0002/input/input4 <6>[ 5.710263] hid-generic 0003:17EF:6009.0002: input: USB HID v1.10 Mouse [Lite-On Technology Corp. ThinkPad USB Keyboard with TrackPoint] on usb-ci_hdrc.1-1.1/input1 <4>[ 5.729598] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 5.737523] panel-simple panel-lcd: Specify missing connector_type <4>[ 5.745434] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.680145] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 7.689730] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.719638] Sending DHCP requests ., OK <6>[ 7.763870] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.35 <6>[ 7.772178] IP-Config: Complete: <6>[ 7.775680] device=eth0, hwaddr=00:19:b8:08:f1:09, ipaddr=192.168.201.35, mask=255.255.255.0, gw=192.168.201.1 <6>[ 7.786395] host=imx6q-sabrelite-lava-cbg-5, domain=lava-rack, nis-domain=(none) <6>[ 7.794515] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 7.794521] nameserver0=192.168.201.1 <6>[ 7.812448] Freeing unused kernel memory: 2048K <6>[ 7.860675] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 8.002287] udevd[135]: starting version 3.2.9 <5>[ 8.007883] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.015189] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.022058] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 8.037412] udevd[135]: specified user 'tss' unknown <27>[ 8.043408] udevd[135]: specified group 'tss' unknown <30>[ 8.051151] udevd[136]: starting eudev-3.2.9 <6>[ 8.352963] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 8.360123] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 8.370928] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.378843] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.402086] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.427352] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.435430] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.505948] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.509034] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.522592] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.531245] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.539896] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.576992] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.584992] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.593791] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.643805] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.682399] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.751868] caam 2100000.crypto: Entropy delay = 3200 <6>[ 8.755890] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.795247] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.815920] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.817991] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 8.822774] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 8.878751] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 8.884197] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 8.891107] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 8.939764] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 8.946137] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 8.952593] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 8.962480] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <6>[ 8.970856] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.979385] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.988057] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.996636] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 9.051240] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 9.059544] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <27>[ 9.064831] udevd[146]: Error calling EVIOCSKEYCODE on device node '/dev/input/event1' (scan code 0x90010, key code 190): Invalid argument <4>[ 9.067743] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 9.073358] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.073511] panel-simple panel-lcd: Specify missing connector_type <27>[ 9.083507] udevd[146]: Error calling EVIOCSKEYCODE on device node '/dev/input/event1' (scan code 0x90011, key code 148): Invalid argument <4>[ 9.088973] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <6>[ 9.096543] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.096592] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.096651] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <27>[ 9.098452] udevd[146]: Error calling EVIOCSKEYCODE on device node '/dev/input/event1' (scan code 0x90012, key code 152): Invalid argument <27>[ 9.098484] udevd[146]: Error calling EVIOCSKEYCODE on device node '/dev/input/event1' (scan code 0x90013, key code 236): Invalid argument <27>[ 9.098509] udevd[146]: Error calling EVIOCSKEYCODE on device node '/dev/input/event1' (scan code 0x90014, key code 238): Invalid argument <27>[ 9.098534] udevd[146]: Error calling EVIOCSKEYCODE on device node '/dev/input/event1' (scan code 0x90015, key code 212): Invalid argument <27>[ 9.098561] udevd[146]: Error calling EVIOCSKEYCODE on device node '/dev/input/event1' (scan code 0x90016, key code 227): Invalid argument <4>[ 9.103271] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <6>[ 9.116018] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 9.155158] sgtl5000 0-000a: sgtl5000 revision 0x11 <4>[ 9.248038] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 9.269415] panel-simple panel-lcd: supply power not found, using dummy regulator <6>[ 9.270600] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <4>[ 9.277440] panel-simple panel-lcd: Specify missing connector_type <6>[ 9.296476] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.305070] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.313639] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.322233] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 9.332666] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 9.347095] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.355106] panel-simple panel-lcd: Specify missing connector_type <6>[ 9.367489] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.376102] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.384761] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.393314] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 9.507433] caam algorithms registered in /proc/crypto <6>[ 9.514786] caam 2100000.crypto: registering rng-caam <4>[ 9.522413] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 9.536847] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.544889] panel-simple panel-lcd: Specify missing connector_type <6>[ 9.556492] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.565054] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.573576] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) done<6>[ 9.582127] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) Saving random seed: <4>[ 9.593014] panel-simple panel-lvds0: supply power not found, using dummy regulator <5>[ 9.600698] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 9.702710] random: crng init done <5>[ 9.706488] random: 1 urandom warning(s) missed due to ratelimiting OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-7724746/environment . /lava-7724746/environment / # /lava-7724746/bin/lava-test-runner /lava-7724746/0 /lava-7724746/bin/lava-test-runner /lava-7724746/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-7724746/0/tests/0_dmesg + c<8>[ 10.306811] at uuid + UUID=7724746_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 10.350478] <8>[ 10.391358] <8>[ 10.432491] + set<8>[ 10.442396] +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-7724746/environment / # . /lava-7724746/environment/lava-7724746/bin/lava-test-runner /lava-7724746/1 / # /lava-7724746/bin/lava-test-runner /lava-7724746/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-7724746/1/tests/1_bootrr +<8>[ 10.937470] cat uuid + UUID=7724746_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/helpers:/lava-7724746/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr + sh helpers/bootrr-auto /lava-7724746/1/../bin/lava-test-case <8>[ 11.991418] /lava-7724746/1/../bin/lava-test-case <8>[ 12.030805] /lava-7724746/1/../bin/lava-test-case <8>[ 12.055747] + set<8>[ 12.074881] +x / #