connecting to NetworkSerialPort(target=Target(name='tegra124-jetson-tk1', env=None), name='USBSerialPort', state=, avail=True, host='nuc-1', port=54947, speed=115200, protocol='rfc2217') calling microcom -s 115200 -t nuc-1:54947 connected to 192.168.0.1 (port 54947) Escape character: Ctrl-\ Type the escape character to get to the prompt. U-Boot SPL 2015.10 (Dec 03 2015 - 13:25:02) U-Boot 2015.10 (Dec 03 2015 - 13:25:02 -0800) TEGRA124 Model: NVIDIA Jetson TK1 Board: NVIDIA Jetson TK1 DRAM: 2 GiB MC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 tegra-pcie: PCI regions: tegra-pcie: I/O: 0x12000000-0x12010000 tegra-pcie: non-prefetchable memory: 0x13000000-0x20000000 tegra-pcie: prefetchable memory: 0x20000000-0x40000000 tegra-pcie: 2x1, 1x1 configuration tegra-pcie: probing port 0, using 2 lanes tegra-pcie: link 0 down, retrying tegra-pcie: link 0 down, retrying tegra-pcie: link 0 down, retrying tegra-pcie: link 0 down, ignoring tegra-pcie: probing port 1, using 1 lanes In: serial Out: serial Err: serial Net: RTL8169#0 Hit any key to stop autoboot: 2  0 Tegra124 (Jetson TK1) # setenv autoload no setenv autoload no Tegra124 (Jetson TK1)setenv initrd_high 0xffffffff # setenv initrd_high 0xffffffff Tegra124 (Jetson TK1) # setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff Tegra124 (Jetson TK1) # dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.0.212 (8 ms) Tegra124 (Jetson TK1) # setenv serverip 192.168.0.2 setenv serverip 192.168.0.2 Tegra124 (Jetson TK1) # tftp 0x81000000 2749532/tftp-deploy-1jxzbuvt/kernel/zImage tftp 0x81000000 2749532/tftp-deploy-1jxzbuvt/kernel/zImage Using RTL8169#0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.212 Filename '2749532/tftp-deploy-1jxzbuvt/kernel/zImage'. Load address: 0x81000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######### 2.6 MiB/s done Bytes transferred = 9667072 (938200 hex) Tegra124 (Jetson TK1) # tftp 0x82800000 2749532/tftp-deploy-1jxzbuvt/ramdisk/ramdisk.cpio.gz.uboot tftp 0x82800000 2749532/tftp-deploy-1jxzbuvt/ramdisk/ramdisk.cpio.gz.uboot Using RTL8169#0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.212 Filename '2749532/tftp-deploy-1jxzbuvt/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x82800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####################################################### 2.8 MiB/s done Bytes transferred = 16064878 (f5216e hex) Tegra124 (Jetson TK1) # setenv initrd_size ${filesize} setenv initrd_size ${filesize} Tegra124 (Jetson TK1) # tftp 0x83f80000 2749532/tftp-deploy-1jxzbuvt/dtb/tegra124-jetson-tk1.dtb tftp 0x83f80000 2749532/tftp-deploy-1jxzbuvt/dtb/tegra124-jetson-tk1.dtb Using RTL8169#0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.212 Filename '2749532/tftp-deploy-1jxzbuvt/dtb/tegra124-jetson-tk1.dtb'. Load address: 0x83f80000 Loading: *##### 2.2 MiB/s done Bytes transferred = 66855 (10527 hex) Tegra124 (Jetson TK1) # setenv bootargs 'console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=:::::eth0:dhcp' setenv bootargs 'console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=:::::eth0:dhcp' Tegra124 (Jetson TK1) # bootz 0x81000000 0x82800000 0x83f80000 bootz 0x81000000 0x82800000 0x83f80000 Kernel image @ 0x81000000 [ 0x000000 - 0x938200 ] ## Loading init Ramdisk from Legacy Image at 82800000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16064814 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 83f80000 Booting using the fdt blob at 0x83f80000 Using Device Tree in place at 83f80000, end 83f93526 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.150-cip18 (KernelCI@build-j387978-arm-gcc-10-multi-v7-defconfig-g88cr) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Oct 26 17:09:25 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [413fc0f3] revision 3 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: NVIDIA Tegra124 Jetson TK1 [ 0.000000] earlycon: uart0 at MMIO 0x70006300 (options '115200n8') [ 0.000000] printk: bootconsole [uart0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0xfb800000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000afffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x00000000b0000000-0x00000000ffefffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000ffefffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000000ffefffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522496 [ 0.000000] Kernel command line: console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=:::::eth0:dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 1972976K/2096128K available (13312K kernel code, 2230K rwdata, 5344K rodata, 2048K init, 424K bss, 57616K reserved, 65536K cma-reserved, 1244160K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] /interrupt-controller@60004000: 160 interrupts forwarded to /interrupt-controller@50041000 <6>[ 0.000011] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483647500ns <6>[ 0.008952] clocksource: timer_us: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275 ns <6>[ 0.019148] Switching to timer-based delay loop, resolution 1000ns <6>[ 0.030391] clocksource: tegra_suspend_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns <6>[ 0.044065] arch_timer: cp15 timer(s) running at 12.00MHz (virt). <6>[ 0.050662] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2c47f4ee7, max_idle_ns: 440795202497 ns <6>[ 0.062122] sched_clock: 56 bits at 12MHz, resolution 83ns, wraps every 4398046511096ns <6>[ 0.070694] Switching to timer-based delay loop, resolution 83ns <6>[ 0.077759] Console: colour dummy device 80x30 <6>[ 0.082671] Calibrating delay loop (skipped), value calculated using timer frequency.. 24.00 BogoMIPS (lpj=120000) <6>[ 0.093694] pid_max: default: 32768 minimum: 301 <6>[ 0.098897] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.106766] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.115660] CPU: Testing write buffer coherency: ok <6>[ 0.121035] CPU0: Spectre v2: using ICIALLU workaround <6>[ 0.126634] CPU0: Spectre BHB: enabling loop workaround for all CPUs <3>[ 0.133701] /cpus/cpu@0 missing clock-frequency property <3>[ 0.139515] /cpus/cpu@1 missing clock-frequency property <3>[ 0.145344] /cpus/cpu@2 missing clock-frequency property <3>[ 0.151156] /cpus/cpu@3 missing clock-frequency property <6>[ 0.156948] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.163614] Setting up static identity map for 0x80300000 - 0x803000ac <6>[ 0.172634] rcu: Hierarchical SRCU implementation. <6>[ 0.181316] Tegra Revision: A01 SKU: 129 CPU Process: 1 SoC Process: 1 <6>[ 0.189169] EFI services will not be available. <6>[ 0.194375] smp: Bringing up secondary CPUs ... <6>[ 0.199983] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <3>[ 0.199992] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable <6>[ 0.216998] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <3>[ 0.217007] CPU2: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable <6>[ 0.233989] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <3>[ 0.233998] CPU3: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable <6>[ 0.250362] smp: Brought up 1 node, 4 CPUs <6>[ 0.254902] SMP: Total of 4 processors activated (96.00 BogoMIPS). <6>[ 0.261580] CPU: All CPU(s) started in SVC mode. <6>[ 0.267185] devtmpfs: initialized <6>[ 0.283896] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 <6>[ 0.292332] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.302822] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.311524] pinctrl core: initialized pinctrl subsystem <6>[ 0.319070] DMI not present or invalid. <6>[ 0.323932] NET: Registered protocol family 16 <6>[ 0.331000] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.341142] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.341806] cpuidle: using governor menu <6>[ 0.452805] No ATAGs? <6>[ 0.455564] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.464156] hw-breakpoint: maximum watchpoint size is 8 bytes. <6>[ 0.485390] Serial: AMBA PL011 UART driver <6>[ 0.491464] platform 50000000.host1x: Adding to iommu group 0 <6>[ 0.497778] platform 57000000.gpu: Adding to iommu group 1 <6>[ 0.531271] +5V_SYS: supplied by +VDD_MUX <6>[ 0.536094] +3.3V_SYS: supplied by +VDD_MUX <6>[ 0.541669] +USB0_VBUS_SW: supplied by +5V_SYS <6>[ 0.546929] +5V_USB_HS: supplied by +5V_SYS <6>[ 0.552336] +5V_HDMI_CON: supplied by +5V_SYS <6>[ 0.557518] +5V_SATA: supplied by +5V_SYS <6>[ 0.562197] reg-fixed-voltage regulator@11: nonexclusive access to GPIO for regulator@11 <6>[ 0.571036] +12V_SATA: supplied by +VDD_MUX <6>[ 0.578140] iommu: Default domain type: Translated <6>[ 0.583794] vgaarb: loaded <5>[ 0.587653] SCSI subsystem initialized <6>[ 0.592282] usbcore: registered new interface driver usbfs <6>[ 0.598293] usbcore: registered new interface driver hub <6>[ 0.604109] usbcore: registered new device driver usb <6>[ 0.611094] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.616513] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.626282] PTP clock support registered <6>[ 0.634057] clocksource: Switched to clocksource arch_sys_counter <6>[ 1.702620] NET: Registered protocol family 2 <6>[ 1.707650] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.716729] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 1.725721] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 1.734122] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 1.741961] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 1.748926] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.756118] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.763846] NET: Registered protocol family 1 <6>[ 1.769150] RPC: Registered named UNIX socket transport module. <6>[ 1.775595] RPC: Registered udp transport module. <6>[ 1.780749] RPC: Registered tcp transport module. <6>[ 1.785915] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.792868] PCI: CLS 0 bytes, default 64 <6>[ 1.797590] Trying to unpack rootfs image as initramfs... <6>[ 2.974925] Freeing initrd memory: 15692K <6>[ 2.980234] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available <5>[ 2.990157] Initialise system trusted keyrings <6>[ 2.995273] workingset: timestamp_bits=30 max_order=19 bucket_order=0 <6>[ 3.008852] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.015883] NFS: Registering the id_resolver key type <5>[ 3.021433] Key type id_resolver registered <5>[ 3.026067] Key type id_legacy registered <6>[ 3.030594] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.037833] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.045814] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.051018] Key type asymmetric registered <5>[ 3.055566] Asymmetric key parser 'x509' registered <6>[ 3.060944] bounce: pool size: 64 pages <6>[ 3.065239] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 3.073181] io scheduler mq-deadline registered <6>[ 3.078163] io scheduler kyber registered <6>[ 3.101334] tegra-pcie 1003000.pcie: host bridge /pcie@1003000 ranges: <6>[ 3.108430] tegra-pcie 1003000.pcie: MEM 0x0001000000..0x0001001fff -> 0x0001000000 <6>[ 3.117127] tegra-pcie 1003000.pcie: IO 0x0012000000..0x001200ffff -> 0x0000000000 <6>[ 3.125822] tegra-pcie 1003000.pcie: MEM 0x0013000000..0x001fffffff -> 0x0013000000 <6>[ 3.134510] tegra-pcie 1003000.pcie: MEM 0x0020000000..0x003fffffff -> 0x0020000000 <6>[ 3.143287] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration <6>[ 3.161759] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver registered 32 channels <6>[ 3.175045] tegra-pmc 7000e400.pmc: emergency thermal reset enabled <6>[ 3.238953] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.249435] printk: console [ttyS0] disabled <6>[ 3.254222] 70006300.serial: ttyS0 at MMIO 0x70006300 (irq = 84, base_baud = 25500000) is a Tegra <6>[ 3.263726] printk: console [ttyS0] enabled <6>[ 3.263726] printk: console [ttyS0] enabled <6>[ 3.272769] printk: bootconsole [uart0] disabled <6>[ 3.272769] printk: bootconsole [uart0] disabled <6>[ 3.283956] SuperH (H)SCI(F) driver initialized <6>[ 3.289856] msm_serial: driver initialized <6>[ 3.294427] STMicroelectronics ASC driver initialized <6>[ 3.300763] 70006000.serial: ttyTHS1 at MMIO 0x70006000 (irq = 82, base_baud = 0) is a TEGRA_UART <6>[ 3.310467] 70006040.serial: ttyTHS2 at MMIO 0x70006040 (irq = 83, base_baud = 0) is a TEGRA_UART <6>[ 3.320635] STM32 USART driver initialized <6>[ 3.328446] platform 54200000.dc: Adding to iommu group 2 <6>[ 3.336714] platform 54240000.dc: Adding to iommu group 2 <6>[ 3.347447] platform 54340000.vic: Adding to iommu group 2 <4>[ 3.357586] Failed to attached device 54200000.dc to IOMMU_mapping <4>[ 3.372369] Failed to attached device 54240000.dc to IOMMU_mapping <4>[ 3.389388] Failed to attached device 54340000.vic to IOMMU_mapping <6>[ 3.406771] brd: module loaded <6>[ 3.418012] loop: module loaded <4>[ 3.424706] tegra-ahci 70027000.sata: supply ahci not found, using dummy regulator <4>[ 3.432662] tegra-ahci 70027000.sata: supply phy not found, using dummy regulator <6>[ 3.450444] spi-nor spi1.0: w25q32dw (4096 Kbytes) <6>[ 3.460912] CAN device driver interface <6>[ 3.466052] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.473207] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.478466] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.484715] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.490370] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.500940] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.508644] usbcore: registered new interface driver pegasus <6>[ 3.514622] usbcore: registered new interface driver asix <6>[ 3.520309] usbcore: registered new interface driver ax88179_178a <6>[ 3.526702] usbcore: registered new interface driver cdc_ether <6>[ 3.532828] usbcore: registered new interface driver smsc75xx <6>[ 3.538891] usbcore: registered new interface driver smsc95xx <6>[ 3.544939] usbcore: registered new interface driver net1080 <6>[ 3.550883] usbcore: registered new interface driver cdc_subset <6>[ 3.557108] usbcore: registered new interface driver zaurus <6>[ 3.562998] usbcore: registered new interface driver cdc_ncm <4>[ 3.569295] tegra-phy 7d000000.usb-phy: supply vbus not found, using dummy regulator <4>[ 3.577599] tegra-phy 7d004000.usb-phy: supply vbus not found, using dummy regulator <6>[ 3.588611] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.595417] ehci-pci: EHCI PCI platform driver <6>[ 3.600153] ehci-platform: EHCI generic platform driver <6>[ 3.605866] ehci-orion: EHCI orion driver <6>[ 3.610301] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.614736] ehci-st: EHCI STMicroelectronics driver <6>[ 3.620022] ehci-exynos: EHCI Exynos driver <6>[ 3.624625] ehci-atmel: EHCI Atmel driver <6>[ 3.629030] tegra-ehci: Tegra EHCI driver <6>[ 3.637713] tegra-ehci 7d004000.usb: EHCI Host Controller <6>[ 3.643387] tegra-ehci 7d004000.usb: new USB bus registered, assigned bus number 1 <6>[ 3.651417] tegra-ehci 7d004000.usb: irq 105, io mem 0x7d004000 <6>[ 3.684050] tegra-ehci 7d004000.usb: USB 2.0 started, EHCI 1.10 <6>[ 3.690938] hub 1-0:1.0: USB hub found <6>[ 3.695003] hub 1-0:1.0: 1 port detected <6>[ 3.701786] tegra-ehci 7d008000.usb: EHCI Host Controller <6>[ 3.707478] tegra-ehci 7d008000.usb: new USB bus registered, assigned bus number 2 <6>[ 3.715471] tegra-ehci 7d008000.usb: irq 106, io mem 0x7d008000 <6>[ 3.744052] tegra-ehci 7d008000.usb: USB 2.0 started, EHCI 1.10 <6>[ 3.750875] hub 2-0:1.0: USB hub found <6>[ 3.754938] hub 2-0:1.0: 1 port detected <6>[ 3.759559] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.766022] ohci-pci: OHCI PCI platform driver <6>[ 3.770767] ohci-platform: OHCI generic platform driver <6>[ 3.776472] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.780892] ohci-st: OHCI STMicroelectronics driver <6>[ 3.786200] ohci-atmel: OHCI Atmel driver <6>[ 3.791298] usbcore: registered new interface driver usb-storage <6>[ 3.809482] tegra_rtc 7000e000.rtc: registered as rtc1 <5>[ 3.814908] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock <6>[ 3.821962] i2c /dev entries driver <4>[ 3.833060] at24 0-0056: supply vcc not found, using dummy regulator <6>[ 3.840772] at24 0-0056: 256 byte 24c02 EEPROM, writable, 8 bytes/write <6>[ 3.853599] as3722 4-0040: AS3722 with revision 0x1 found <6>[ 3.866474] +1.35V_LP0(sd2): supplied by +5V_SYS <6>[ 3.871786] +1.35V_LP0(sd3): Bringing 0uV into 1350000-1350000uV <6>[ 3.878212] +1.35V_LP0(sd3): supplied by +5V_SYS <6>[ 3.883700] +1.05V_RUN: supplied by +5V_SYS <6>[ 3.888421] +1.8V_VDDIO: supplied by +5V_SYS <6>[ 3.894778] +1.05V_RUN_AVDD: supplied by +1.35V_LP0(sd2) <6>[ 3.901250] +1.8V_RUN_CAM: Bringing 0uV into 1800000-1800000uV <6>[ 3.907913] +1.2V_GEN_AVDD: supplied by +1.8V_VDDIO <6>[ 3.914139] +1.05V_LP0_VDD_RTC: Bringing 1100000uV into 1000000-1000000uV <6>[ 3.921315] +1.05V_LP0_VDD_RTC: supplied by +3.3V_SYS <6>[ 3.927696] +2.8V_RUN_CAM: Bringing 0uV into 2800000-2800000uV <6>[ 3.934146] +2.8V_RUN_CAM: supplied by +3.3V_SYS <6>[ 3.939271] +1.2V_RUN_CAM_FRONT: Bringing 0uV into 1200000-1200000uV <6>[ 3.946242] +1.2V_RUN_CAM_FRONT: supplied by +1.8V_VDDIO <3>[ 3.952044] +VDDIO_SDMMC3: bypassed regulator has no supply! <3>[ 3.957982] +VDDIO_SDMMC3: failed to get the current voltage: -EPROBE_DEFER <3>[ 3.965248] as3722-regulator as3722-regulator: regulator 13 register failed -517 <6>[ 3.978295] as3722-rtc as3722-rtc: registered as rtc0 <6>[ 3.983936] as3722-rtc as3722-rtc: setting system clock to 2000-01-01T00:00:18 UTC (946684818) <6>[ 3.992825] as3722-rtc as3722-rtc: RTC interrupt 388 <4>[ 4.006941] lm90 0-004c: supply vcc not found, using dummy regulator <6>[ 4.016347] hwmon hwmon0: temp1_input not attached to any thermal zone <6>[ 4.023275] hwmon hwmon0: temp2_input not attached to any thermal zone <6>[ 4.039240] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.045698] sdhci: Copyright(c) Pierre Ossman <6>[ 4.052512] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.060414] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.067607] sdhci-tegra 700b0400.mmc: Got CD GPIO <6>[ 4.072607] sdhci-tegra 700b0400.mmc: Got WP GPIO <6>[ 4.078089] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.085171] usbcore: registered new interface driver usbhid <4>[ 4.088540] mmc1: Invalid maximum block size, assuming 512 bytes <6>[ 4.090998] usbhid: USB HID core driver <6>[ 4.096941] NET: Registered protocol family 10 <6>[ 4.106867] Segment Routing with IPv6 <6>[ 4.110853] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.117610] NET: Registered protocol family 17 <6>[ 4.122320] can: controller area network core <6>[ 4.127011] NET: Registered protocol family 29 <6>[ 4.128729] mmc1: SDHCI controller on 700b0600.mmc [700b0600.mmc] using ADMA 64-bit <6>[ 4.131717] can: raw protocol <6>[ 4.142871] can: broadcast manager protocol <6>[ 4.147332] can: netlink gateway - max_hops=1 <5>[ 4.152270] Key type dns_resolver registered <6>[ 4.157979] ThumbEE CPU extension supported. <5>[ 4.162526] Registering SWP/SWPB emulation handler <5>[ 4.167908] Loading compiled-in X.509 certificates <6>[ 4.198236] +3.3V_RUN: supplied by +3.3V_SYS <6>[ 4.204994] +3.3V_LP0: supplied by +3.3V_SYS <6>[ 4.210671] +3.3V_AVDD_HDMI_AP_GATED: supplied by +3.3V_RUN <6>[ 4.215763] mmc1: new high speed MMC card at address 0001 <3>[ 4.217575] tegra-xusb-padctl 7009f000.padctl: failed to get regulators: -517 <6>[ 4.230631] mmcblk1: mmc1:0001 SEM16G 14.7 GiB <6>[ 4.232101] tegra-pcie 1003000.pcie: host bridge /pcie@1003000 ranges: <6>[ 4.235755] mmcblk1boot0: mmc1:0001 SEM16G partition 1 4.00 MiB <6>[ 4.242297] tegra-pcie 1003000.pcie: MEM 0x0001000000..0x0001001fff -> 0x0001000000 <6>[ 4.248692] mmcblk1boot1: mmc1:0001 SEM16G partition 2 4.00 MiB <6>[ 4.256838] tegra-pcie 1003000.pcie: IO 0x0012000000..0x001200ffff -> 0x0000000000 <6>[ 4.271389] tegra-pcie 1003000.pcie: MEM 0x0013000000..0x001fffffff -> 0x0013000000 <6>[ 4.271599] mmcblk1rpmb: mmc1:0001 SEM16G partition 3 4.00 MiB, chardev (235:0) <6>[ 4.279796] tegra-pcie 1003000.pcie: MEM 0x0020000000..0x003fffffff -> 0x0020000000 <6>[ 4.292112] mmcblk1: p1 p2 p3 p4 p5 p6 p7 p8 <6>[ 4.295852] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration <4>[ 4.311947] tegra-ahci 70027000.sata: supply ahci not found, using dummy regulator <4>[ 4.319996] tegra-ahci 70027000.sata: supply phy not found, using dummy regulator <4>[ 4.329526] as3722-regulator as3722-regulator: DMA mask not set <6>[ 4.340098] +1.35V_LP0(sd2): supplied by +5V_SYS <6>[ 4.345363] +1.35V_LP0(sd3): supplied by +5V_SYS <6>[ 4.350636] +1.05V_RUN: supplied by +5V_SYS <6>[ 4.355236] +1.8V_VDDIO: supplied by +5V_SYS <6>[ 4.361500] +1.05V_RUN_AVDD: supplied by +1.35V_LP0(sd2) <6>[ 4.368151] +1.8V_RUN_CAM: supplied by +3.3V_RUN <6>[ 4.373145] +1.2V_GEN_AVDD: supplied by +1.8V_VDDIO <6>[ 4.379273] +1.05V_LP0_VDD_RTC: supplied by +3.3V_SYS <6>[ 4.385723] +2.8V_RUN_CAM: supplied by +3.3V_SYS <6>[ 4.390857] +1.2V_RUN_CAM_FRONT: supplied by +1.8V_VDDIO <3>[ 4.396555] +VDDIO_SDMMC3: bypassed regulator has no supply! <3>[ 4.402471] +VDDIO_SDMMC3: failed to get the current voltage: -EPROBE_DEFER <6>[ 4.409753] +VDDIO_SDMMC3: supplied by +3.3V_RUN <6>[ 4.415725] +1.05V_RUN_CAM_REAR: Bringing 0uV into 1050000-1050000uV <6>[ 4.423004] +1.05V_RUN_CAM_REAR: supplied by +1.8V_VDDIO <6>[ 4.429463] +3.3V_RUN_TOUCH: Bringing 0uV into 2800000-2800000uV <6>[ 4.436901] +3.3V_RUN_TOUCH: supplied by +5V_SYS <6>[ 4.442394] +2.8V_RUN_CAM_AF: Bringing 0uV into 2800000-2800000uV <6>[ 4.449455] +2.8V_RUN_CAM_AF: supplied by +5V_SYS <6>[ 4.455296] +1.8V_RUN_VPP_FUSE: Bringing 0uV into 1800000-1800000uV <6>[ 4.462515] +1.8V_RUN_VPP_FUSE: supplied by +3.3V_RUN <6>[ 4.472421] sdhci-tegra 700b0400.mmc: Got CD GPIO <4>[ 4.473338] usb2-0: supply vbus not found, using dummy regulator <6>[ 4.477469] sdhci-tegra 700b0400.mmc: Got WP GPIO <4>[ 4.484038] usb2-1: supply vbus not found, using dummy regulator <4>[ 4.495548] usb3-0: supply vbus not found, using dummy regulator <4>[ 4.502381] mmc0: Invalid maximum block size, assuming 512 bytes <6>[ 4.503698] tegra-pcie 1003000.pcie: host bridge /pcie@1003000 ranges: <6>[ 4.515525] tegra-pcie 1003000.pcie: MEM 0x0001000000..0x0001001fff -> 0x0001000000 <6>[ 4.523905] tegra-pcie 1003000.pcie: IO 0x0012000000..0x001200ffff -> 0x0000000000 <6>[ 4.532313] tegra-pcie 1003000.pcie: MEM 0x0013000000..0x001fffffff -> 0x0013000000 <6>[ 4.540687] tegra-pcie 1003000.pcie: MEM 0x0020000000..0x003fffffff -> 0x0020000000 <6>[ 4.545044] mmc0: SDHCI controller on 700b0400.mmc [700b0400.mmc] using ADMA 64-bit <6>[ 4.549202] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration <6>[ 4.565201] tegra-pcie 1003000.pcie: probing port 0, using 2 lanes <6>[ 4.573686] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes <6>[ 4.894196] mmc0: new high speed SD card at address 0260 <6>[ 4.900750] mmcblk0: mmc0:0260 1232 961 MiB <6>[ 4.907629] mmcblk0: p1 p2 <6>[ 5.790605] tegra-pcie 1003000.pcie: link 0 down, ignoring <6>[ 5.800886] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 <6>[ 5.807469] pci_bus 0000:00: root bus resource [bus 00-ff] <6>[ 5.813213] pci_bus 0000:00: root bus resource [mem 0x01000000-0x01001fff] <6>[ 5.820358] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] <6>[ 5.826808] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] <6>[ 5.833937] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] <6>[ 5.841927] pci 0000:00:02.0: [10de:0e13] type 01 class 0x060400 <4>[ 5.848211] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4 may corrupt adjacent RW1C bits <6>[ 5.858167] pci 0000:00:02.0: enabling Extended Tags <6>[ 5.863466] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold <6>[ 5.874728] PCI: bus0: Fast back to back transfers disabled <6>[ 5.880561] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring <6>[ 5.889034] pci 0000:01:00.0: [10ec:8168] type 00 class 0x020000 <6>[ 5.895345] pci 0000:01:00.0: reg 0x10: [io 0x0000-0x00ff] <6>[ 5.901210] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit] <6>[ 5.908304] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] <6>[ 5.915981] pci 0000:01:00.0: supports D1 D2 <6>[ 5.920511] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold <6>[ 5.958663] PCI: bus1: Fast back to back transfers disabled <6>[ 5.964563] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 5.971472] pci 0000:00:02.0: BAR 8: assigned [mem 0x13000000-0x130fffff] <6>[ 5.978558] pci 0000:00:02.0: BAR 9: assigned [mem 0x20000000-0x200fffff 64bit pref] <6>[ 5.986573] pci 0000:00:02.0: BAR 7: assigned [io 0x1000-0x1fff] <6>[ 5.992929] pci 0000:01:00.0: BAR 4: assigned [mem 0x20000000-0x20003fff 64bit pref] <6>[ 6.000962] pci 0000:01:00.0: BAR 2: assigned [mem 0x13000000-0x13000fff 64bit] <6>[ 6.008559] pci 0000:01:00.0: BAR 0: assigned [io 0x1000-0x10ff] <6>[ 6.014931] pci 0000:00:02.0: PCI bridge to [bus 01] <6>[ 6.020156] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] <6>[ 6.026524] pci 0000:00:02.0: bridge window [mem 0x13000000-0x130fffff] <6>[ 6.033570] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref] <4>[ 6.041609] pci 0000:00:02.0: nv_msi_ht_cap_quirk didn't locate host bridge <6>[ 6.048979] pcieport 0000:00:02.0: enabling device (0140 -> 0143) <6>[ 6.055482] pcieport 0000:00:02.0: PME: Signaling with IRQ 33 <6>[ 6.061937] r8169 0000:01:00.0: enabling device (0140 -> 0143) <6>[ 6.120905] r8169 0000:01:00.0 eth0: RTL8168g/8111g, 00:04:4b:21:2a:66, XID 4c0, IRQ 404 <6>[ 6.129308] r8169 0000:01:00.0 eth0: jumbo features [frames: 9194 bytes, tx checksumming: ko] <6>[ 6.147143] +1.05V_RUN_AVDD_HDMI_PLL: supplied by +1.05V_RUN <6>[ 6.156655] drm drm: [drm] Cannot find any crtc or sizes <6>[ 6.162591] drm drm: [drm] Cannot find any crtc or sizes <6>[ 6.169070] [drm] Initialized tegra 0.0.0 20120330 for drm on minor 0 <4>[ 6.177508] tegra-ahci 70027000.sata: supply ahci not found, using dummy regulator <4>[ 6.185587] tegra-ahci 70027000.sata: supply phy not found, using dummy regulator <4>[ 6.193495] tegra-ahci 70027000.sata: supply target not found, using dummy regulator <6>[ 6.202906] tegra-ahci 70027000.sata: AHCI 0001.0301 32 slots 2 ports 3 Gbps 0x1 impl platform mode <6>[ 6.212267] tegra-ahci 70027000.sata: flags: 64bit ncq sntf pm led pmp pio slum part sadm sds apst <6>[ 6.223476] scsi host0: tegra-ahci <6>[ 6.228641] scsi host1: tegra-ahci <6>[ 6.232559] ata1: SATA max UDMA/133 mmio [mem 0x70027000-0x70028fff] port 0x100 irq 94 <6>[ 6.240777] ata2: DUMMY <6>[ 6.245579] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 696000 KHz, changing to: 714000 KHz <6>[ 6.257177] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 6.575446] ata1: SATA link down (SStatus 0 SControl 300) <4>[ 6.586819] r8169 0000:01:00.0: Direct firmware load for rtl_nic/rtl8168g-2.fw failed with error -2 <3>[ 6.596374] r8169 0000:01:00.0: Unable to load firmware rtl_nic/rtl8168g-2.fw (-2) <6>[ 6.644603] Generic FE-GE Realtek PHY r8169-0-100:00: attached PHY driver [Generic FE-GE Realtek PHY] (mii_bus:phy_addr=r8169-0-100:00, irq=IGNORE) <6>[ 6.825206] r8169 0000:01:00.0 eth0: Link is Down <6>[ 8.446568] r8169 0000:01:00.0 eth0: Link is Up - 100Mbps/Full - flow control rx/tx <6>[ 8.474588] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 8.504255] Sending DHCP requests ., OK <6>[ 8.548633] IP-Config: Got DHCP answer from 192.168.0.1, my address is 192.168.0.212 <6>[ 8.556706] IP-Config: Complete: <6>[ 8.560206] device=eth0, hwaddr=00:04:4b:21:2a:66, ipaddr=192.168.0.212, mask=255.255.255.0, gw=192.168.0.254 <6>[ 8.570867] host=192.168.0.212, domain=, nis-domain=(none) <6>[ 8.577105] bootserver=192.168.0.1, rootserver=192.168.0.1, rootpath= <6>[ 8.577118] nameserver0=192.168.0.1, nameserver1=192.168.1.254 <6>[ 8.592704] Freeing unused kernel memory: 2048K <6>[ 8.666166] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 8.747028] udevd[143]: starting version 3.2.9 <5>[ 8.752312] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.759219] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.766079] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 8.775564] udevd[143]: specified user 'tss' unknown <27>[ 8.780911] udevd[143]: specified group 'tss' unknown <30>[ 8.787411] udevd[144]: starting eudev-3.2.9 <6>[ 8.934098] tegra-wdt 60005000.timer: initialized (heartbeat = 120 sec, nowayout = 0) <27>[ 8.977020] udevd[150]: Error changing net interface name eth0 to enp1s0: Device or resource busy <28>[ 8.994843] udevd[150]: could not rename interface '3' from 'eth0' to 'enp1s0': Device or resource busy <6>[ 9.006619] nouveau 57000000.gpu: NVIDIA GK20A (0ea000a1) <6>[ 9.012323] nouveau 57000000.gpu: imem: using IOMMU <3>[ 9.017792] nouveau 57000000.gpu: gr ctor failed, -2 <4>[ 9.037893] nouveau: probe of 57000000.gpu failed with error -2 <4>[ 9.045494] tegra-xusb 70090000.usb: Direct firmware load for nvidia/tegra124/xusb.bin failed with error -2 <3>[ 9.055568] tegra-xusb 70090000.usb: failed to request firmware: -2 <3>[ 9.062094] tegra-xusb 70090000.usb: failed to request firmware: -2 <4>[ 9.069442] tegra-xusb: probe of 70090000.usb failed with error -2 <6>[ 9.110770] input: tegra-hda HDMI/DP,pcm=3 as /devices/soc0/70030000.hda/sound/card0/input1 <3>[ 9.134081] tegra-snd-rt5640 sound: snd_soc_register_card failed (-517) <4>[ 9.252603] tegra30-i2s 70301100.i2s: DMA channels sourced from device 70300000.ahub <3>[ 9.262325] tegra-snd-rt5640 sound: snd_soc_register_card failed (-517) done Saving random seed: <6>[ 9.529812] input: NVIDIA Tegra Jetson TK1 Headphones as /devices/soc0/sound/sound/card1/input2 OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-2749532/environment . /lava-2749532/environment / # /lava-2749532/bin/lava-test-runner /lava-2749532/0 /lava-2749532/bin/lava-test-runner /lava-2749532/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-2749532/0/tests/0_dmesg + cat uuid + UUID=2749532_1.5<8>[ 10.203815] .2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 10.229611] <8>[ 10.259946] <8>[ 10.286019] + set +x <8>[ 10.295756] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-2749532/environment / # . /lava-2749532/environment/lava-2749532/bin/lava-test-runner /lava-2749532/1 / # /lava-2749532/bin/lava-test-runner /lava-2749532/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-2749532/1/tests/1_bootrr + cat uuid + UUID=2<8>[ 10.783376] 749532_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/helpers:/lava-2749532/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr + sh helpers/bootrr-auto /lava-2749532/1/../bin/lava-test-case <8>[ 11.832276] /lava-2749532/1/../bin/lava-test-case <8>[ 11.864773] /lava-2749532/1/../bin/lava-test-case <8>[ 11.882544] + set +x <8>[ 11.897858] / #