connecting to NetworkSerialPort(target=Target(name='tegra124-jetson-tk1', env=None), name='USBSerialPort', state=, avail=True, host='nuc-1', port=48047, speed=115200, protocol='rfc2217') calling microcom -s 115200 -t nuc-1:48047 connected to 192.168.0.1 (port 48047) Escape character: Ctrl-\ Type the escape character to get to the prompt. U-Boot SPL 2015.10 (Dec 03 2015 - 13:25:02) U-Boot 2015.10 (Dec 03 2015 - 13:25:02 -0800) TEGRA124 Model: NVIDIA Jetson TK1 Board: NVIDIA Jetson TK1 DRAM: 2 GiB MC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 tegra-pcie: PCI regions: tegra-pcie: I/O: 0x12000000-0x12010000 tegra-pcie: non-prefetchable memory: 0x13000000-0x20000000 tegra-pcie: prefetchable memory: 0x20000000-0x40000000 tegra-pcie: 2x1, 1x1 configuration tegra-pcie: probing port 0, using 2 lanes tegra-pcie: link 0 down, retrying tegra-pcie: link 0 down, retrying tegra-pcie: link 0 down, retrying tegra-pcie: link 0 down, ignoring tegra-pcie: probing port 1, using 1 lanes In: serial Out: serial Err: serial Net: RTL8169#0 Hit any key to stop autoboot: 2  0 Tegra124 (Jetson TK1) # setenv autoload no setenv autoload no Tegra124 (Jetson TK1) # setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff Tegra124 (Jetson TK1) # setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff Tegra124 (Jetson TK1) # dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.0.212 (7 ms) Tegra124 (Jetson TK1) # setenv serverip 192.168.0.2 setenv serverip 192.168.0.2 Tegra124 (Jetson TK1) # tftp 0x81000000 2766035/tftp-deploy-g112hrpg/kernel/zImage tftp 0x81000000 2766035/tftp-deploy-g112hrpg/kernel/zImage Using RTL8169#0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.212 Filename '2766035/tftp-deploy-g112hrpg/kernel/zImage'. Load address: 0x81000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ##################T ############################################### ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######### 1.1 MiB/s done Bytes transferred = 9667072 (938200 hex) Tegra124 (Jetson TK1) # tftp 0x82800000 2766035/tftp-deploy-g112hrpg/ramdisk/ramdisk.cpio.gz.uboot tftp 0x82800000 2766035/tftp-deploy-g112hrpg/ramdisk/ramdisk.cpio.gz.uboot Using RTL8169#0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.212 Filename '2766035/tftp-deploy-g112hrpg/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x82800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####################################################### 3.1 MiB/s done Bytes transferred = 16063067 (f51a5b hex) Tegra124 (Jetson TK1) # setenv initrd_size ${filesize} setenv initrd_size ${filesize} Tegra124 (Jetson TK1) # tftp 0x83f80000 2766035/tftp-deploy-g112hrpg/dtb/tegra124-jetson-tk1.dtb tftp 0x83f80000 2766035/tftp-deploy-g112hrpg/dtb/tegra124-jetson-tk1.dtb Using RTL8169#0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.212 Filename '2766035/tftp-deploy-g112hrpg/dtb/tegra124-jetson-tk1.dtb'. Load address: 0x83f80000 Loading: *##### 2.9 MiB/s done Bytes transferred = 66855 (10527 hex) Tegra124 (Jetson TK1) # setenv bootargs 'console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=:::::eth0:dhcp' setenv bootargs 'console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=:::::eth0:dhcp' Tegra124 (Jetson TK1) # bootz 0x81000000 0x82800000 0x83f80000 bootz 0x81000000 0x82800000 0x83f80000 Kernel image @ 0x81000000 [ 0x000000 - 0x938200 ] ## Loading init Ramdisk from Legacy Image at 82800000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16063003 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 83f80000 Booting using the fdt blob at 0x83f80000 Using Device Tree in place at 83f80000, end 83f93526 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.151-cip18 (KernelCI@build-j408522-arm-gcc-10-multi-v7-defconfig-kvrkn) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Fri Oct 28 13:57:16 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [413fc0f3] revision 3 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: NVIDIA Tegra124 Jetson TK1 [ 0.000000] earlycon: uart0 at MMIO 0x70006300 (options '115200n8') [ 0.000000] printk: bootconsole [uart0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0xfb800000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000afffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x00000000b0000000-0x00000000ffefffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000ffefffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000000ffefffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522496 [ 0.000000] Kernel command line: console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=:::::eth0:dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 1972980K/2096128K available (13312K kernel code, 2230K rwdata, 5344K rodata, 2048K init, 424K bss, 57612K reserved, 65536K cma-reserved, 1244160K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] /interrupt-controller@60004000: 160 interrupts forwarded to /interrupt-controller@50041000 <6>[ 0.000010] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483647500ns <6>[ 0.008953] clocksource: timer_us: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275 ns <6>[ 0.019148] Switching to timer-based delay loop, resolution 1000ns <6>[ 0.030404] clocksource: tegra_suspend_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns <6>[ 0.044072] arch_timer: cp15 timer(s) running at 12.00MHz (virt). <6>[ 0.050670] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2c47f4ee7, max_idle_ns: 440795202497 ns <6>[ 0.062129] sched_clock: 56 bits at 12MHz, resolution 83ns, wraps every 4398046511096ns <6>[ 0.070702] Switching to timer-based delay loop, resolution 83ns <6>[ 0.077765] Console: colour dummy device 80x30 <6>[ 0.082675] Calibrating delay loop (skipped), value calculated using timer frequency.. 24.00 BogoMIPS (lpj=120000) <6>[ 0.093699] pid_max: default: 32768 minimum: 301 <6>[ 0.098901] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.106768] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.115658] CPU: Testing write buffer coherency: ok <6>[ 0.121033] CPU0: Spectre v2: using ICIALLU workaround <6>[ 0.126632] CPU0: Spectre BHB: enabling loop workaround for all CPUs <3>[ 0.133700] /cpus/cpu@0 missing clock-frequency property <3>[ 0.139513] /cpus/cpu@1 missing clock-frequency property <3>[ 0.145341] /cpus/cpu@2 missing clock-frequency property <3>[ 0.151154] /cpus/cpu@3 missing clock-frequency property <6>[ 0.156945] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.163610] Setting up static identity map for 0x80300000 - 0x803000ac <6>[ 0.172624] rcu: Hierarchical SRCU implementation. <6>[ 0.181311] Tegra Revision: A01 SKU: 129 CPU Process: 1 SoC Process: 1 <6>[ 0.189164] EFI services will not be available. <6>[ 0.194369] smp: Bringing up secondary CPUs ... <6>[ 0.199981] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <3>[ 0.199989] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable <6>[ 0.216997] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <3>[ 0.217006] CPU2: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable <6>[ 0.233992] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <3>[ 0.234000] CPU3: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable <6>[ 0.250366] smp: Brought up 1 node, 4 CPUs <6>[ 0.254907] SMP: Total of 4 processors activated (96.00 BogoMIPS). <6>[ 0.261585] CPU: All CPU(s) started in SVC mode. <6>[ 0.267188] devtmpfs: initialized <6>[ 0.283864] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 <6>[ 0.292301] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.302793] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.311498] pinctrl core: initialized pinctrl subsystem <6>[ 0.319045] DMI not present or invalid. <6>[ 0.323903] NET: Registered protocol family 16 <6>[ 0.330973] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.341113] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.341788] cpuidle: using governor menu <6>[ 0.452708] No ATAGs? <6>[ 0.455484] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.464054] hw-breakpoint: maximum watchpoint size is 8 bytes. <6>[ 0.485291] Serial: AMBA PL011 UART driver <6>[ 0.491384] platform 50000000.host1x: Adding to iommu group 0 <6>[ 0.497678] platform 57000000.gpu: Adding to iommu group 1 <6>[ 0.531091] +5V_SYS: supplied by +VDD_MUX <6>[ 0.535935] +3.3V_SYS: supplied by +VDD_MUX <6>[ 0.541481] +USB0_VBUS_SW: supplied by +5V_SYS <6>[ 0.546757] +5V_USB_HS: supplied by +5V_SYS <6>[ 0.552145] +5V_HDMI_CON: supplied by +5V_SYS <6>[ 0.557347] +5V_SATA: supplied by +5V_SYS <6>[ 0.562007] reg-fixed-voltage regulator@11: nonexclusive access to GPIO for regulator@11 <6>[ 0.570866] +12V_SATA: supplied by +VDD_MUX <6>[ 0.577969] iommu: Default domain type: Translated <6>[ 0.583641] vgaarb: loaded <5>[ 0.587473] SCSI subsystem initialized <6>[ 0.592068] usbcore: registered new interface driver usbfs <6>[ 0.598100] usbcore: registered new interface driver hub <6>[ 0.603917] usbcore: registered new device driver usb <6>[ 0.610875] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.616293] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.626065] PTP clock support registered <6>[ 0.633967] clocksource: Switched to clocksource arch_sys_counter <6>[ 1.701612] NET: Registered protocol family 2 <6>[ 1.706627] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.715691] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 1.724676] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 1.733055] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 1.740940] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 1.747898] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.755090] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.762822] NET: Registered protocol family 1 <6>[ 1.768115] RPC: Registered named UNIX socket transport module. <6>[ 1.774567] RPC: Registered udp transport module. <6>[ 1.779716] RPC: Registered tcp transport module. <6>[ 1.784883] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.791835] PCI: CLS 0 bytes, default 64 <6>[ 1.796566] Trying to unpack rootfs image as initramfs... <6>[ 2.974128] Freeing initrd memory: 15688K <6>[ 2.979429] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available <5>[ 2.989344] Initialise system trusted keyrings <6>[ 2.994463] workingset: timestamp_bits=30 max_order=19 bucket_order=0 <6>[ 3.008053] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.015076] NFS: Registering the id_resolver key type <5>[ 3.020609] Key type id_resolver registered <5>[ 3.025243] Key type id_legacy registered <6>[ 3.029769] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.037008] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.044988] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.050207] Key type asymmetric registered <5>[ 3.054754] Asymmetric key parser 'x509' registered <6>[ 3.060131] bounce: pool size: 64 pages <6>[ 3.064424] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 3.072367] io scheduler mq-deadline registered <6>[ 3.077349] io scheduler kyber registered <6>[ 3.100545] tegra-pcie 1003000.pcie: host bridge /pcie@1003000 ranges: <6>[ 3.107640] tegra-pcie 1003000.pcie: MEM 0x0001000000..0x0001001fff -> 0x0001000000 <6>[ 3.116336] tegra-pcie 1003000.pcie: IO 0x0012000000..0x001200ffff -> 0x0000000000 <6>[ 3.125035] tegra-pcie 1003000.pcie: MEM 0x0013000000..0x001fffffff -> 0x0013000000 <6>[ 3.133708] tegra-pcie 1003000.pcie: MEM 0x0020000000..0x003fffffff -> 0x0020000000 <6>[ 3.142501] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration <6>[ 3.160946] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver registered 32 channels <6>[ 3.174250] tegra-pmc 7000e400.pmc: emergency thermal reset enabled <6>[ 3.238098] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.248579] printk: console [ttyS0] disabled <6>[ 3.253345] 70006300.serial: ttyS0 at MMIO 0x70006300 (irq = 84, base_baud = 25500000) is a Tegra <6>[ 3.262868] printk: console [ttyS0] enabled <6>[ 3.262868] printk: console [ttyS0] enabled <6>[ 3.271911] printk: bootconsole [uart0] disabled <6>[ 3.271911] printk: bootconsole [uart0] disabled <6>[ 3.283116] SuperH (H)SCI(F) driver initialized <6>[ 3.289007] msm_serial: driver initialized <6>[ 3.293549] STMicroelectronics ASC driver initialized <6>[ 3.299913] 70006000.serial: ttyTHS1 at MMIO 0x70006000 (irq = 82, base_baud = 0) is a TEGRA_UART <6>[ 3.309624] 70006040.serial: ttyTHS2 at MMIO 0x70006040 (irq = 83, base_baud = 0) is a TEGRA_UART <6>[ 3.319850] STM32 USART driver initialized <6>[ 3.327737] platform 54200000.dc: Adding to iommu group 2 <6>[ 3.336003] platform 54240000.dc: Adding to iommu group 2 <6>[ 3.346722] platform 54340000.vic: Adding to iommu group 2 <4>[ 3.356872] Failed to attached device 54200000.dc to IOMMU_mapping <4>[ 3.371620] Failed to attached device 54240000.dc to IOMMU_mapping <4>[ 3.388658] Failed to attached device 54340000.vic to IOMMU_mapping <6>[ 3.405911] brd: module loaded <6>[ 3.417082] loop: module loaded <4>[ 3.423721] tegra-ahci 70027000.sata: supply ahci not found, using dummy regulator <4>[ 3.431730] tegra-ahci 70027000.sata: supply phy not found, using dummy regulator <6>[ 3.449544] spi-nor spi1.0: w25q32dw (4096 Kbytes) <6>[ 3.460006] CAN device driver interface <6>[ 3.465170] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.472310] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.477552] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.483784] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.489458] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.500041] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.507750] usbcore: registered new interface driver pegasus <6>[ 3.513701] usbcore: registered new interface driver asix <6>[ 3.519406] usbcore: registered new interface driver ax88179_178a <6>[ 3.525808] usbcore: registered new interface driver cdc_ether <6>[ 3.531936] usbcore: registered new interface driver smsc75xx <6>[ 3.537999] usbcore: registered new interface driver smsc95xx <6>[ 3.544050] usbcore: registered new interface driver net1080 <6>[ 3.549993] usbcore: registered new interface driver cdc_subset <6>[ 3.556216] usbcore: registered new interface driver zaurus <6>[ 3.562110] usbcore: registered new interface driver cdc_ncm <4>[ 3.568409] tegra-phy 7d000000.usb-phy: supply vbus not found, using dummy regulator <4>[ 3.576720] tegra-phy 7d004000.usb-phy: supply vbus not found, using dummy regulator <6>[ 3.587741] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.594548] ehci-pci: EHCI PCI platform driver <6>[ 3.599283] ehci-platform: EHCI generic platform driver <6>[ 3.605002] ehci-orion: EHCI orion driver <6>[ 3.609440] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.613854] ehci-st: EHCI STMicroelectronics driver <6>[ 3.619155] ehci-exynos: EHCI Exynos driver <6>[ 3.623740] ehci-atmel: EHCI Atmel driver <6>[ 3.628168] tegra-ehci: Tegra EHCI driver <6>[ 3.636025] tegra-ehci 7d004000.usb: EHCI Host Controller <6>[ 3.641701] tegra-ehci 7d004000.usb: new USB bus registered, assigned bus number 1 <6>[ 3.649725] tegra-ehci 7d004000.usb: irq 105, io mem 0x7d004000 <6>[ 3.683960] tegra-ehci 7d004000.usb: USB 2.0 started, EHCI 1.10 <6>[ 3.690822] hub 1-0:1.0: USB hub found <6>[ 3.694910] hub 1-0:1.0: 1 port detected <6>[ 3.701670] tegra-ehci 7d008000.usb: EHCI Host Controller <6>[ 3.707371] tegra-ehci 7d008000.usb: new USB bus registered, assigned bus number 2 <6>[ 3.715387] tegra-ehci 7d008000.usb: irq 106, io mem 0x7d008000 <6>[ 3.743960] tegra-ehci 7d008000.usb: USB 2.0 started, EHCI 1.10 <6>[ 3.750785] hub 2-0:1.0: USB hub found <6>[ 3.754866] hub 2-0:1.0: 1 port detected <6>[ 3.759492] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.765960] ohci-pci: OHCI PCI platform driver <6>[ 3.770701] ohci-platform: OHCI generic platform driver <6>[ 3.776421] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.780840] ohci-st: OHCI STMicroelectronics driver <6>[ 3.786162] ohci-atmel: OHCI Atmel driver <6>[ 3.791261] usbcore: registered new interface driver usb-storage <6>[ 3.809191] tegra_rtc 7000e000.rtc: registered as rtc1 <5>[ 3.814623] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock <6>[ 3.821673] i2c /dev entries driver <4>[ 3.832754] at24 0-0056: supply vcc not found, using dummy regulator <6>[ 3.840470] at24 0-0056: 256 byte 24c02 EEPROM, writable, 8 bytes/write <6>[ 3.853434] as3722 4-0040: AS3722 with revision 0x1 found <6>[ 3.866290] +1.35V_LP0(sd2): supplied by +5V_SYS <6>[ 3.871596] +1.35V_LP0(sd3): Bringing 0uV into 1350000-1350000uV <6>[ 3.878024] +1.35V_LP0(sd3): supplied by +5V_SYS <6>[ 3.883509] +1.05V_RUN: supplied by +5V_SYS <6>[ 3.888228] +1.8V_VDDIO: supplied by +5V_SYS <6>[ 3.894588] +1.05V_RUN_AVDD: supplied by +1.35V_LP0(sd2) <6>[ 3.901040] +1.8V_RUN_CAM: Bringing 0uV into 1800000-1800000uV <6>[ 3.907693] +1.2V_GEN_AVDD: supplied by +1.8V_VDDIO <6>[ 3.913914] +1.05V_LP0_VDD_RTC: Bringing 1100000uV into 1000000-1000000uV <6>[ 3.921113] +1.05V_LP0_VDD_RTC: supplied by +3.3V_SYS <6>[ 3.927506] +2.8V_RUN_CAM: Bringing 0uV into 2800000-2800000uV <6>[ 3.933952] +2.8V_RUN_CAM: supplied by +3.3V_SYS <6>[ 3.939066] +1.2V_RUN_CAM_FRONT: Bringing 0uV into 1200000-1200000uV <6>[ 3.946046] +1.2V_RUN_CAM_FRONT: supplied by +1.8V_VDDIO <3>[ 3.951849] +VDDIO_SDMMC3: bypassed regulator has no supply! <3>[ 3.957787] +VDDIO_SDMMC3: failed to get the current voltage: -EPROBE_DEFER <3>[ 3.965044] as3722-regulator as3722-regulator: regulator 13 register failed -517 <6>[ 3.978090] as3722-rtc as3722-rtc: registered as rtc0 <6>[ 3.983734] as3722-rtc as3722-rtc: setting system clock to 2000-01-01T00:00:22 UTC (946684822) <6>[ 3.992629] as3722-rtc as3722-rtc: RTC interrupt 388 <4>[ 4.006767] lm90 0-004c: supply vcc not found, using dummy regulator <6>[ 4.016105] hwmon hwmon0: temp1_input not attached to any thermal zone <6>[ 4.023032] hwmon hwmon0: temp2_input not attached to any thermal zone <6>[ 4.038971] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.045431] sdhci: Copyright(c) Pierre Ossman <6>[ 4.052250] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.060136] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.067306] sdhci-tegra 700b0400.mmc: Got CD GPIO <6>[ 4.072307] sdhci-tegra 700b0400.mmc: Got WP GPIO <6>[ 4.077723] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.084795] usbcore: registered new interface driver usbhid <4>[ 4.085837] mmc1: Invalid maximum block size, assuming 512 bytes <6>[ 4.090620] usbhid: USB HID core driver <6>[ 4.096546] NET: Registered protocol family 10 <6>[ 4.106499] Segment Routing with IPv6 <6>[ 4.110486] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.117251] NET: Registered protocol family 17 <6>[ 4.121960] can: controller area network core <6>[ 4.126646] NET: Registered protocol family 29 <6>[ 4.128342] mmc1: SDHCI controller on 700b0600.mmc [700b0600.mmc] using ADMA 64-bit <6>[ 4.131351] can: raw protocol <6>[ 4.142507] can: broadcast manager protocol <6>[ 4.146968] can: netlink gateway - max_hops=1 <5>[ 4.151921] Key type dns_resolver registered <6>[ 4.157633] ThumbEE CPU extension supported. <5>[ 4.162181] Registering SWP/SWPB emulation handler <5>[ 4.167807] Loading compiled-in X.509 certificates <6>[ 4.198131] +3.3V_RUN: supplied by +3.3V_SYS <6>[ 4.204951] +3.3V_LP0: supplied by +3.3V_SYS <6>[ 4.210681] +3.3V_AVDD_HDMI_AP_GATED: supplied by +3.3V_RUN <6>[ 4.213514] mmc1: new high speed MMC card at address 0001 <3>[ 4.217591] tegra-xusb-padctl 7009f000.padctl: failed to get regulators: -517 <6>[ 4.222888] mmcblk1: mmc1:0001 SEM16G 14.7 GiB <6>[ 4.232112] tegra-pcie 1003000.pcie: host bridge /pcie@1003000 ranges: <6>[ 4.234805] mmcblk1boot0: mmc1:0001 SEM16G partition 1 4.00 MiB <6>[ 4.241273] tegra-pcie 1003000.pcie: MEM 0x0001000000..0x0001001fff -> 0x0001000000 <6>[ 4.247641] mmcblk1boot1: mmc1:0001 SEM16G partition 2 4.00 MiB <6>[ 4.255795] tegra-pcie 1003000.pcie: IO 0x0012000000..0x001200ffff -> 0x0000000000 <6>[ 4.262547] mmcblk1rpmb: mmc1:0001 SEM16G partition 3 4.00 MiB, chardev (235:0) <6>[ 4.270346] tegra-pcie 1003000.pcie: MEM 0x0013000000..0x001fffffff -> 0x0013000000 <6>[ 4.282637] mmcblk1: p1 p2 p3 p4 p5 p6 p7 p8 <6>[ 4.286273] tegra-pcie 1003000.pcie: MEM 0x0020000000..0x003fffffff -> 0x0020000000 <6>[ 4.299370] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration <4>[ 4.310997] tegra-ahci 70027000.sata: supply ahci not found, using dummy regulator <4>[ 4.319031] tegra-ahci 70027000.sata: supply phy not found, using dummy regulator <4>[ 4.328558] as3722-regulator as3722-regulator: DMA mask not set <6>[ 4.338795] +1.35V_LP0(sd2): supplied by +5V_SYS <6>[ 4.344098] +1.35V_LP0(sd3): supplied by +5V_SYS <6>[ 4.349435] +1.05V_RUN: supplied by +5V_SYS <6>[ 4.354045] +1.8V_VDDIO: supplied by +5V_SYS <6>[ 4.360327] +1.05V_RUN_AVDD: supplied by +1.35V_LP0(sd2) <6>[ 4.367278] +1.8V_RUN_CAM: supplied by +3.3V_RUN <6>[ 4.372244] +1.2V_GEN_AVDD: supplied by +1.8V_VDDIO <6>[ 4.378389] +1.05V_LP0_VDD_RTC: supplied by +3.3V_SYS <6>[ 4.384830] +2.8V_RUN_CAM: supplied by +3.3V_SYS <6>[ 4.389958] +1.2V_RUN_CAM_FRONT: supplied by +1.8V_VDDIO <3>[ 4.395666] +VDDIO_SDMMC3: bypassed regulator has no supply! <3>[ 4.401584] +VDDIO_SDMMC3: failed to get the current voltage: -EPROBE_DEFER <6>[ 4.408854] +VDDIO_SDMMC3: supplied by +3.3V_RUN <6>[ 4.414860] +1.05V_RUN_CAM_REAR: Bringing 0uV into 1050000-1050000uV <6>[ 4.422158] +1.05V_RUN_CAM_REAR: supplied by +1.8V_VDDIO <6>[ 4.428407] +3.3V_RUN_TOUCH: Bringing 0uV into 2800000-2800000uV <6>[ 4.435878] +3.3V_RUN_TOUCH: supplied by +5V_SYS <6>[ 4.441299] +2.8V_RUN_CAM_AF: Bringing 0uV into 2800000-2800000uV <6>[ 4.448428] +2.8V_RUN_CAM_AF: supplied by +5V_SYS <6>[ 4.454266] +1.8V_RUN_VPP_FUSE: Bringing 0uV into 1800000-1800000uV <6>[ 4.461485] +1.8V_RUN_VPP_FUSE: supplied by +3.3V_RUN <6>[ 4.471430] sdhci-tegra 700b0400.mmc: Got CD GPIO <4>[ 4.472384] usb2-0: supply vbus not found, using dummy regulator <6>[ 4.476497] sdhci-tegra 700b0400.mmc: Got WP GPIO <4>[ 4.483090] usb2-1: supply vbus not found, using dummy regulator <4>[ 4.494703] usb3-0: supply vbus not found, using dummy regulator <4>[ 4.501536] mmc0: Invalid maximum block size, assuming 512 bytes <6>[ 4.502859] tegra-pcie 1003000.pcie: host bridge /pcie@1003000 ranges: <6>[ 4.514678] tegra-pcie 1003000.pcie: MEM 0x0001000000..0x0001001fff -> 0x0001000000 <6>[ 4.523059] tegra-pcie 1003000.pcie: IO 0x0012000000..0x001200ffff -> 0x0000000000 <6>[ 4.531469] tegra-pcie 1003000.pcie: MEM 0x0013000000..0x001fffffff -> 0x0013000000 <6>[ 4.539868] tegra-pcie 1003000.pcie: MEM 0x0020000000..0x003fffffff -> 0x0020000000 <6>[ 4.544120] mmc0: SDHCI controller on 700b0400.mmc [700b0400.mmc] using ADMA 64-bit <6>[ 4.548400] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration <6>[ 4.564274] tegra-pcie 1003000.pcie: probing port 0, using 2 lanes <6>[ 4.572769] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes <6>[ 4.903490] mmc0: new high speed SD card at address 0260 <6>[ 4.910012] mmcblk0: mmc0:0260 1232 961 MiB <6>[ 4.917260] mmcblk0: p1 p2 <6>[ 5.788375] tegra-pcie 1003000.pcie: link 0 down, ignoring <6>[ 5.798664] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 <6>[ 5.805243] pci_bus 0000:00: root bus resource [bus 00-ff] <6>[ 5.810988] pci_bus 0000:00: root bus resource [mem 0x01000000-0x01001fff] <6>[ 5.818132] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] <6>[ 5.824583] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] <6>[ 5.831712] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] <6>[ 5.839700] pci 0000:00:02.0: [10de:0e13] type 01 class 0x060400 <4>[ 5.845984] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4 may corrupt adjacent RW1C bits <6>[ 5.855941] pci 0000:00:02.0: enabling Extended Tags <6>[ 5.861239] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold <6>[ 5.872478] PCI: bus0: Fast back to back transfers disabled <6>[ 5.878330] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring <6>[ 5.886790] pci 0000:01:00.0: [10ec:8168] type 00 class 0x020000 <6>[ 5.893083] pci 0000:01:00.0: reg 0x10: [io 0x0000-0x00ff] <6>[ 5.898965] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit] <6>[ 5.906058] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] <6>[ 5.913717] pci 0000:01:00.0: supports D1 D2 <6>[ 5.918262] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold <6>[ 5.958562] PCI: bus1: Fast back to back transfers disabled <6>[ 5.964450] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 5.971347] pci 0000:00:02.0: BAR 8: assigned [mem 0x13000000-0x130fffff] <6>[ 5.978412] pci 0000:00:02.0: BAR 9: assigned [mem 0x20000000-0x200fffff 64bit pref] <6>[ 5.986426] pci 0000:00:02.0: BAR 7: assigned [io 0x1000-0x1fff] <6>[ 5.992787] pci 0000:01:00.0: BAR 4: assigned [mem 0x20000000-0x20003fff 64bit pref] <6>[ 6.000820] pci 0000:01:00.0: BAR 2: assigned [mem 0x13000000-0x13000fff 64bit] <6>[ 6.008418] pci 0000:01:00.0: BAR 0: assigned [io 0x1000-0x10ff] <6>[ 6.014791] pci 0000:00:02.0: PCI bridge to [bus 01] <6>[ 6.020015] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] <6>[ 6.026384] pci 0000:00:02.0: bridge window [mem 0x13000000-0x130fffff] <6>[ 6.033429] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref] <4>[ 6.041470] pci 0000:00:02.0: nv_msi_ht_cap_quirk didn't locate host bridge <6>[ 6.048831] pcieport 0000:00:02.0: enabling device (0140 -> 0143) <6>[ 6.055347] pcieport 0000:00:02.0: PME: Signaling with IRQ 33 <6>[ 6.061797] r8169 0000:01:00.0: enabling device (0140 -> 0143) <6>[ 6.121155] r8169 0000:01:00.0 eth0: RTL8168g/8111g, 00:04:4b:21:2a:66, XID 4c0, IRQ 404 <6>[ 6.129557] r8169 0000:01:00.0 eth0: jumbo features [frames: 9194 bytes, tx checksumming: ko] <6>[ 6.147426] +1.05V_RUN_AVDD_HDMI_PLL: supplied by +1.05V_RUN <6>[ 6.157053] drm drm: [drm] Cannot find any crtc or sizes <6>[ 6.162974] drm drm: [drm] Cannot find any crtc or sizes <6>[ 6.169522] [drm] Initialized tegra 0.0.0 20120330 for drm on minor 0 <4>[ 6.177962] tegra-ahci 70027000.sata: supply ahci not found, using dummy regulator <4>[ 6.186036] tegra-ahci 70027000.sata: supply phy not found, using dummy regulator <4>[ 6.193967] tegra-ahci 70027000.sata: supply target not found, using dummy regulator <6>[ 6.203344] tegra-ahci 70027000.sata: AHCI 0001.0301 32 slots 2 ports 3 Gbps 0x1 impl platform mode <6>[ 6.212706] tegra-ahci 70027000.sata: flags: 64bit ncq sntf pm led pmp pio slum part sadm sds apst <6>[ 6.224045] scsi host0: tegra-ahci <6>[ 6.229133] scsi host1: tegra-ahci <6>[ 6.233055] ata1: SATA max UDMA/133 mmio [mem 0x70027000-0x70028fff] port 0x100 irq 94 <6>[ 6.241272] ata2: DUMMY <6>[ 6.245938] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 696000 KHz, changing to: 714000 KHz <6>[ 6.257607] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 6.576329] ata1: SATA link down (SStatus 0 SControl 300) <4>[ 6.585852] r8169 0000:01:00.0: Direct firmware load for rtl_nic/rtl8168g-2.fw failed with error -2 <3>[ 6.595210] r8169 0000:01:00.0: Unable to load firmware rtl_nic/rtl8168g-2.fw (-2) <6>[ 6.634077] Generic FE-GE Realtek PHY r8169-0-100:00: attached PHY driver [Generic FE-GE Realtek PHY] (mii_bus:phy_addr=r8169-0-100:00, irq=IGNORE) <6>[ 6.815105] r8169 0000:01:00.0 eth0: Link is Down <6>[ 8.361996] r8169 0000:01:00.0 eth0: Link is Up - 100Mbps/Full - flow control rx/tx <6>[ 8.374086] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 8.404187] Sending DHCP requests ., OK <6>[ 8.448768] IP-Config: Got DHCP answer from 192.168.0.1, my address is 192.168.0.212 <6>[ 8.456837] IP-Config: Complete: <6>[ 8.460323] device=eth0, hwaddr=00:04:4b:21:2a:66, ipaddr=192.168.0.212, mask=255.255.255.0, gw=192.168.0.254 <6>[ 8.470946] host=192.168.0.212, domain=, nis-domain=(none) <6>[ 8.477163] bootserver=192.168.0.1, rootserver=192.168.0.1, rootpath= <6>[ 8.477170] nameserver0=192.168.0.1, nameserver1=192.168.1.254 <6>[ 8.492435] Freeing unused kernel memory: 2048K <6>[ 8.546144] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 8.618867] udevd[141]: starting version 3.2.9 <5>[ 8.624384] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.631227] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.638041] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 8.648178] udevd[141]: specified user 'tss' unknown <27>[ 8.653540] udevd[141]: specified group 'tss' unknown <30>[ 8.659975] udevd[142]: starting eudev-3.2.9 <27>[ 8.792458] udevd[151]: Error changing net interface name eth0 to enp1s0: Device or resource busy <28>[ 8.802632] udevd[151]: could not rename interface '3' from 'eth0' to 'enp1s0': Device or resource busy <6>[ 8.811925] tegra-wdt 60005000.timer: initialized (heartbeat = 120 sec, nowayout = 0) <6>[ 8.825707] nouveau 57000000.gpu: NVIDIA GK20A (0ea000a1) <6>[ 8.831409] nouveau 57000000.gpu: imem: using IOMMU <3>[ 8.836964] nouveau 57000000.gpu: gr ctor failed, -2 <4>[ 8.842623] nouveau: probe of 57000000.gpu failed with error -2 <4>[ 8.916453] tegra-xusb 70090000.usb: Direct firmware load for nvidia/tegra124/xusb.bin failed with error -2 <3>[ 8.926469] tegra-xusb 70090000.usb: failed to request firmware: -2 <3>[ 8.932986] tegra-xusb 70090000.usb: failed to request firmware: -2 <4>[ 8.940947] tegra-xusb: probe of 70090000.usb failed with error -2 <3>[ 8.990772] tegra-snd-rt5640 sound: snd_soc_register_card failed (-517) <3>[ 9.005003] tegra-snd-rt5640 sound: snd_soc_register_card failed (-517) <6>[ 9.012353] input: tegra-hda HDMI/DP,pcm=3 as /devices/soc0/70030000.hda/sound/card0/input1 <4>[ 9.113765] tegra30-i2s 70301100.i2s: DMA channels sourced from device 70300000.ahub <3>[ 9.123185] tegra-snd-rt5640 sound: snd_soc_register_card failed (-517) <6>[ 9.360427] input: NVIDIA Tegra Jetson TK1 Headphones as /devices/soc0/sound/sound/card1/input2 done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / #export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-2766035/environment . /lava-2766035/environment / # /lava-2766035/bin/lava-test-runner /lava-2766035/0 /lava-2766035/bin/lava-test-runner /lava-2766035/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-2766035/0/tests/0_dmesg + cat uuid <8>[ 10.056473] + UUID=2766035_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 10.087446] <8>[ 10.112310] <8>[ 10.140751] + set +x <8>[ 10.150537] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-2766035/environment / # . /lava-2766035/environment/lava-2766035/bin/lava-test-runner /lava-2766035/1 / # /lava-2766035/bin/lava-test-runner /lava-2766035/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-2766035/1/tests/1_bootrr + cat uuid<8>[ 10.635202] + UUID=2766035_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/helpers:/lava-2766035/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr + sh helpers/bootrr-auto /lava-2766035/1/../bin/lava-test-case <8>[ 11.692081] /lava-2766035/1/../bin/lava-test-case <8>[ 11.734074] /lava-2766035/1/../bin/lava-test-case <8>[ 11.751879] + set +x <8>[ 11.766986] / #