connecting to NetworkSerialPort(target=Target(name='meson-sm1-khadas-vim3l', env=None), name='USBSerialPort', state=, avail=True, host='nuc-2', port=35437, speed=115200, protocol='rfc2217') calling microcom -s 115200 -t nuc-2:35437 connected to 192.168.0.2 (port 35437) Escape character: Ctrl-\ Type the escape character to get to the prompt. SM1:BL:511f6b:81ca2f;FEAT:A0F83180:20282000;POC:F;RCY:0;EMMC:0;READ:0;CHK:1F;READ:0;0.0;CHK:0; bl2_stage_init 0x01 bl2_stage_init 0x81 hw id: 0x0000 - pwm id 0x01 bl2_stage_init 0xc1 bl2_stage_init 0x02 L0:00000000 L1:00000703 L2:00008067 L3:15000000 S1:00000000 B2:20282000 B1:a0f83180 TE: 211482 BL2 Built : 15:59:24, May 25 2020. g12a gb6bfa83 - gongwei.chen@droid11-sz Board ID = 8 Set cpu clk to 24M Set clk81 to 24M Use GP1_pll as DSU clk. DSU clk: 1200 Mhz CPU clk: 1200 MHz Set clk81 to 166.6M eMMC boot @ 1 sw8 s board id: 8 Load FIP HDR DDR from eMMC, src: 0x00010200, des: 0xfffd0000, size: 0x00004000, part: 1 fw parse done PIEI prepare done ddr saved addr:00016000 Load ddr parameter from eMMC, src: 0x02c00000, des: 0xfffd0000, size: 0x00001000, part: 0 00000000 emmc switch 0 ok fastboot data verify result: 255 Cfg max: 12, cur: 1. Board id: 255. Force loop cfg LPDDR4 probe LPDDR4_PHY_V_0_1_22-Built : 15:59:30, May 25 2020. g12a gb6bfa83 - gongwei.chen@droid11-sz ddr clk to 1608MHz 00000000 emmc switch 1 ok dmc_version 0001 Check phy result INFO : ERROR : Training has failed! Check phy result INFO : ERROR : Training has failed! Check phy result INFO : End of initialization INFO : ERROR : Training has failed! 1D training failed Cfg max: 12, cur: 2. Board id: 255. Force loop cfg LPDDR4 probe ddr clk to 1608MHz dmc_version 0001 Check phy result INFO : End of CA training INFO : End of initialization INFO : Training has run successfully! Check phy result INFO : End of initialization INFO : End of read enable training INFO : End of fine write leveling INFO : End of read dq deskew training INFO : End of MPR read delay center optimization INFO : End of Write leveling coarse delay INFO : End of read delay center optimization INFO : Training has run successfully! Check phy result INFO : End of initialization INFO : End of MPR read delay center optimization INFO : End of write delay center optimization INFO : End of read delay center optimization INFO : End of max read latency training INFO : Training has run successfully! 1D training succeed Check phy result INFO : End of initialization INFO : End of 2D read delay Voltage center optimization INFO : End of 2D read delay Voltage center optimization INFO : End of 2D write delay Voltage center optimization INFO : End of 2D write delay Voltage center optimization INFO : Training has run successfully! soc_vref_reg_value 0x 00000025 00000027 00000024 00000027 00000024 00000026 00000024 00000025 00000026 00000024 00000027 00000027 00000026 00000026 00000026 00000025 00000024 00000025 00000024 00000022 00000022 00000024 00000023 00000024 00000024 00000023 00000027 00000026 00000024 00000024 00000023 00000025 dwc_ddrphy_apb_wr((0<<20)|(2<<16)|(0<<12)|(0xb0):0004 dram_vref_reg_value 0x 00000014 2D training succeed auto size-- 65535DDR cs0 size: 2048MB DDR cs1 size: 0MB DMC_DDR_CTRL: 00c0002cDDR size: 2048MB cs0 DataBus test pass cs0 AddrBus test pass non-sec scramble use zero key ddr scramble enabled 100bdlr_step_size ps== 431 result report boot times 0Enable ddr reg access 00000000 emmc switch 3 ok Authentication key not yet programmed get rpmb counter error 0x00000007 00000000 emmc switch 1 ok Load FIP HDR from eMMC, src: 0x00010200, des: 0x01700000, size: 0x00004000, part: 1 Load BL3X from eMMC, src: 0x00078200, des: 0x01768000, size: 0x000ac200, part: 1 0.0;M3 CHK:0;cm4_sp_mode 0 [Image: g12a_v1.1.3394-7d43064d5 2020-05-07 15:37:06 gongwei.chen@droid11-sz] OPS=0x40 ring efuse init 2b 0b 40 00 01 12 28 00 00 08 31 37 59 54 52 50 [0.014423 Inits done] secure task start! high task start! low task start! boot bl31 NOTICE: BL31: v1.3(release):d9e1bbe85 NOTICE: BL31: Built : 19:07:25, Sep 7 2020 NOTICE: BL31: G12A normal boot! NOTICE: BL31: BL33 decompress pass ERROR: Error initializing runtime service opteed_fast U-Boot 2021.01-00035-g6180f7834d8f (Feb 09 2021 - 15:31:49 -0800) khadas-vim3l Model: Khadas VIM3L SoC: Amlogic Meson SM1 (Unknown) Revision 2b:b (40:2) DRAM: 2 GiB MMC: sd@ffe03000: 0, sd@ffe05000: 1, mmc@ffe07000: 2 Loading Environment from MMC... *** Warning - bad CRC, using default environment In: serial@3000 Out: serial@3000 Err: serial@3000 Net: eth0: ethernet@ff3f0000 Verify GPT: success! switch to partitions #0, OK mmc2(part 0) is current device MMC read: dev # 2, block # 1024, count 4096 ... 4096 blocks read: OK There is no valid bmp file at the given address Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp Speed: 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.0.212 (8 ms) => setenv serverip 192.168.0.2 setenv serverip 192.168.0.2 => tftp 0x1080000 2847804/tftp-deploy-bduikjq5/kernel/Image tftp 0x1080000 2847804/tftp-deploy-bduikjq5/kernel/Image Speed: 100, full duplex Using ethernet@ff3f0000 device TFTP from server 192.168.0.2; our IP address is 192.168.0.212 Filename '2847804/tftp-deploy-bduikjq5/kernel/Image'. Load address: 0x1080000 Loading: *################################################################# ######################################T ##T ######################### ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# #################### 1.1 MiB/s done Bytes transferred = 31775232 (1e4da00 hex) => tftp 0x13000000 2847804/tftp-deploy-bduikjq5/ramdisk/ramdisk.cpio.gz.uboot tftp 0x13000000 2847804/tftp-deploy-bduikjq5/ramdisk/ramdisk.cpio.gz.uboot Speed: 100, full duplex Using ethernet@ff3f0000 device TFTP from server 192.168.0.2; our IP address is 192.168.0.212 Filename '2847804/tftp-deploy-bduikjq5/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x13000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ###################################################### 1.8 MiB/s done Bytes transferred = 18915413 (120a055 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x1000000 2847804/tftp-deploy-bduikjq5/dtb/meson-sm1-khadas-vim3l.dtb tftp 0x1000000 2847804/tftp-deploy-bduikjq5/dtb/meson-sm1-khadas-vim3l.dtb Speed: 100, full duplex Using ethernet@ff3f0000 device TFTP from server 192.168.0.2; our IP address is 192.168.0.212 Filename '2847804/tftp-deploy-bduikjq5/dtb/meson-sm1-khadas-vim3l.dtb'. Load address: 0x1000000 Loading: *#### 1.6 MiB/s done Bytes transferred = 48772 (be84 hex) => setenv bootargs 'console=ttyAML0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttyAML0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => booti 0x1080000 0x13000000 0x1000000 booti 0x1080000 0x13000000 0x1000000 Moving Image from 0x1080000 to 0x1200000, end=30e0000 ## Loading init Ramdisk from Legacy Image at 13000000 ... Image Name: Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 18915349 Bytes = 18 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01000000 Booting using the fdt blob at 0x1000000 Loading Ramdisk to 74d01000, end 75f0b015 ... OK Loading Device Tree to 0000000074cf2000, end 0000000074d00e83 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x411fd050] [ 0.000000] Linux version 5.10.154-cip19 (KernelCI@build-j492615-arm64-gcc-10-defconfig-8b98x) (aarch64-linux-gnu-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP PREEMPT Fri Nov 11 03:23:43 UTC 2022 [ 0.000000] Machine model: Khadas VIM3L [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: failed to reserve memory for node 'secmon@5000000': base 0x0000000005000000, size 3 MiB [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000064c00000, size 256 MiB [ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool [ 0.000000] earlycon: meson0 at MMIO 0x00000000ff803000 (options '115200n8') [ 0.000000] printk: bootconsole [meson0] enabled [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x000000007fe5afff] [ 0.000000] NUMA: NODE_DATA [mem 0x7fa1bb00-0x7fa1dfff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x000000007fe5afff] [ 0.000000] DMA32 empty [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x00000000052fffff] [ 0.000000] node 0: [mem 0x0000000005300000-0x00000000072fffff] [ 0.000000] node 0: [mem 0x0000000007300000-0x000000007fe5afff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000007fe5afff] [ 0.000000] On node 0, zone DMA: 421 pages in unavailable ranges [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 23 pages/cpu s56600 r8192 d29416 u94208 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: Virtualization Host Extensions [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] alternatives: patching kernel code [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 515681 [ 0.000000] Policy zone: DMA [ 0.000000] Kernel command line: console=ttyAML0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 1706772K/2095468K available (14528K kernel code, 2806K rwdata, 7604K rodata, 5952K init, 512K bss, 126552K reserved, 262144K cma-reserved) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] GIC: Using split EOI/Deactivate mode <6>[ 0.000000] irq_meson_gpio: 100 to 8 gpio interrupt mux initialized <6>[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns <6>[ 0.000004] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns <6>[ 0.008613] Console: colour dummy device 80x25 <6>[ 0.013119] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) <6>[ 0.023633] pid_max: default: 32768 minimum: 301 <6>[ 0.028598] LSM: Security Framework initializing <6>[ 0.033484] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 0.041139] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 0.050655] rcu: Hierarchical SRCU implementation. <6>[ 0.057485] EFI services will not be available. <6>[ 0.059463] smp: Bringing up secondary CPUs ... <6>[ 0.064756] Detected VIPT I-cache on CPU1 <6>[ 0.064815] CPU1: Booted secondary processor 0x0000000100 [0x411fd050] <6>[ 0.065625] Detected VIPT I-cache on CPU2 <6>[ 0.065667] CPU2: Booted secondary processor 0x0000000200 [0x411fd050] <6>[ 0.066458] Detected VIPT I-cache on CPU3 <6>[ 0.066496] CPU3: Booted secondary processor 0x0000000300 [0x411fd050] <6>[ 0.066568] smp: Brought up 1 node, 4 CPUs <6>[ 0.101693] SMP: Total of 4 processors activated. <6>[ 0.106671] CPU features: detected: Privileged Access Never <6>[ 0.112549] CPU features: detected: LSE atomic instructions <6>[ 0.118398] CPU features: detected: User Access Override <6>[ 0.124006] CPU features: detected: 32-bit EL0 Support <6>[ 0.129420] CPU features: detected: Common not Private translations <6>[ 0.135994] CPU features: detected: RAS Extension Support <6>[ 0.141671] CPU features: detected: Data cache clean to the PoU not required for I/D coherence <6>[ 0.150593] CPU features: detected: CRC32 instructions <6>[ 0.156019] CPU features: detected: 32-bit EL1 Support <6>[ 0.177241] CPU: All CPU(s) started at EL2 <6>[ 0.178844] devtmpfs: initialized <4>[ 0.187609] KASLR disabled due to lack of seed <6>[ 0.187789] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.196762] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.210429] pinctrl core: initialized pinctrl subsystem <6>[ 0.211798] DMI not present or invalid. <6>[ 0.215010] NET: Registered protocol family 16 <6>[ 0.220543] DMA: preallocated 256 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.226587] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.234671] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations <6>[ 0.242816] audit: initializing netlink subsys (disabled) <5>[ 0.248591] audit: type=2000 audit(0.180:1): state=initialized audit_enabled=0 res=1 <6>[ 0.249774] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.256499] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.263087] cpuidle: using governor menu <6>[ 0.273981] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.280997] ASID allocator initialised with 65536 entries <6>[ 0.288125] Serial: AMBA PL011 UART driver <6>[ 0.335172] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.336508] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.343525] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.350535] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.358642] cryptd: max_cpu_qlen set to 1000 <6>[ 0.364433] ACPI: Interpreter disabled. <3>[ 0.368005] reg-fixed-voltage regulator-vcc_1v8: Failed to register regulator: -517 <3>[ 0.374206] reg-fixed-voltage regulator-vcc_3v3: Failed to register regulator: -517 <3>[ 0.382168] reg-fixed-voltage regulator-vddao_1v8: Failed to register regulator: -517 <3>[ 0.390305] reg-fixed-voltage regulator-emmc_1v8: Failed to register regulator: -517 <6>[ 0.398352] VSYS_3V3: supplied by DC_IN <6>[ 0.403288] iommu: Default domain type: Translated <6>[ 0.407813] vgaarb: loaded <5>[ 0.410789] SCSI subsystem initialized <6>[ 0.414908] usbcore: registered new interface driver usbfs <6>[ 0.420382] usbcore: registered new interface driver hub <6>[ 0.425967] usbcore: registered new device driver usb <6>[ 0.432061] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.436527] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.445986] PTP clock support registered <6>[ 0.450305] EDAC MC: Ver: 3.0.0 <6>[ 0.455224] FPGA manager framework <6>[ 0.457321] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.464372] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.470212] VFS: Disk quotas dquot_6.6.0 <6>[ 0.474290] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 0.481587] pnp: PnP ACPI: disabled <6>[ 0.490910] NET: Registered protocol family 2 <6>[ 0.491084] IP idents hash table entries: 32768 (order: 6, 262144 bytes, linear) <6>[ 0.498476] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes, linear) <6>[ 0.506489] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 0.514741] TCP bind hash table entries: 16384 (order: 6, 262144 bytes, linear) <6>[ 0.522438] TCP: Hash tables configured (established 16384 bind 16384) <6>[ 0.529192] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear) <6>[ 0.536119] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, linear) <6>[ 0.543662] NET: Registered protocol family 1 <6>[ 0.548581] RPC: Registered named UNIX socket transport module. <6>[ 0.554398] RPC: Registered udp transport module. <6>[ 0.559363] RPC: Registered tcp transport module. <6>[ 0.564347] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.571088] PCI: CLS 0 bytes, default 64 <6>[ 0.575424] Unpacking initramfs... <6>[ 1.312460] Freeing initrd memory: 18472K <6>[ 1.313224] kvm [1]: IPA Size Limit: 40 bits <6>[ 1.315753] kvm [1]: vgic interrupt IRQ9 <6>[ 1.319993] kvm [1]: VHE mode initialized successfully <5>[ 1.328869] Initialise system trusted keyrings <6>[ 1.330144] workingset: timestamp_bits=42 max_order=19 bucket_order=0 <6>[ 1.342255] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.343431] NFS: Registering the id_resolver key type <5>[ 1.348236] Key type id_resolver registered <5>[ 1.352655] Key type id_legacy registered <6>[ 1.357030] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 1.363941] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 1.371781] 9p: Installing v9fs 9p2000 file system support <5>[ 1.412310] Key type asymmetric registered <5>[ 1.412333] Asymmetric key parser 'x509' registered <6>[ 1.416216] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 1.423895] io scheduler mq-deadline registered <6>[ 1.428700] io scheduler kyber registered <4>[ 1.447394] EINJ: ACPI disabled. <6>[ 1.460460] soc soc0: Amlogic Meson SM1 (Unknown) Revision 2b:b (40:2) Detected <6>[ 1.470640] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled6>[ 1.477014] ff803000.serial: ttyAML0 at MMIO 0xff803000 (irq = 22, base_baud = 1500000) is a meson_uart <6>[ 1.486703] printk: console [ttyAML0] enabled <6>[ 1.486703] printk: console [ttyAML0] enabled <6>[ 1.490268] printk: bootconsole [meson0] disabled <6>[ 1.490268] printk: bootconsole [meson0] disabled <6>[ 1.500815] ffd24000.serial: ttyAML6 at MMIO 0xffd24000 (irq = 29, base_baud = 1500000) is a meson_uart <6>[ 1.509769] serial serial0: tty port ttyAML6 registered <6>[ 1.515620] msm_serial: driver initialized <6>[ 1.527642] loop: module loaded <6>[ 1.528739] megasas: 07.714.04.00-rc1 <6>[ 1.535388] tun: Universal TUN/TAP device driver, 1.6 <6>[ 1.536317] thunder_xcv, ver 1.0 <6>[ 1.538567] thunder_bgx, ver 1.0 <6>[ 1.541995] nicpf, ver 1.0 <6>[ 1.546271] hclge is initializing <6>[ 1.548460] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 1.555852] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 1.561416] e1000: Intel(R) PRO/1000 Network Driver <6>[ 1.566461] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 1.572446] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 1.577587] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 1.583742] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 1.589317] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.595127] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 1.601572] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 1.608110] sky2: driver version 1.30 <6>[ 1.612867] VFIO - User Level meta-driver version: 0.3 <6>[ 1.619106] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 1.623660] ehci-pci: EHCI PCI platform driver <6>[ 1.628334] ehci-platform: EHCI generic platform driver <6>[ 1.633902] ehci-orion: EHCI orion driver <6>[ 1.638091] ehci-exynos: EHCI Exynos driver <6>[ 1.642482] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 1.648764] ohci-pci: OHCI PCI platform driver <6>[ 1.653437] ohci-platform: OHCI generic platform driver <6>[ 1.658974] ohci-exynos: OHCI Exynos driver <6>[ 1.663841] usbcore: registered new interface driver usb-storage <6>[ 1.672482] i2c /dev entries driver <6>[ 1.682734] sdhci: Secure Digital Host Controller Interface driver <6>[ 1.683529] sdhci: Copyright(c) Pierre Ossman <6>[ 1.688834] Synopsys Designware Multimedia Card Interface Driver <6>[ 1.695690] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 1.695939] meson-gx-mmc ffe05000.sd: Got CD GPIO <6>[ 1.705128] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 1.712707] meson-sm: secure-monitor enabled <6>[ 1.717234] usbcore: registered new interface driver usbhid <6>[ 1.721588] usbhid: USB HID core driver <3>[ 1.728532] meson-saradc ff809000.adc: failed to get vref regulator <6>[ 1.735927] NET: Registered protocol family 17 <6>[ 1.736909] 9pnet: Installing 9P2000 support <5>[ 1.741298] Key type dns_resolver registered <6>[ 1.746025] registered taskstats version 1 <5>[ 1.750052] Loading compiled-in X.509 certificates <6>[ 1.768566] VCC_5V: supplied by DC_IN <3>[ 1.769021] reg-fixed-voltage regulator-vcc_1v8: Failed to register regulator: -517 <6>[ 1.776049] VCC_3V3: supplied by VSYS_3V3 <6>[ 1.779440] VDDIO_AO1V8: supplied by VSYS_3V3 <6>[ 1.783953] EMMC_AO1V8: supplied by VCC_3V3 <6>[ 1.788472] USB_PWR: supplied by VCC_5V <6>[ 1.798159] dwc3-meson-g12a ffe09000.usb: USB2 ports: 2 <6>[ 1.798192] dwc3-meson-g12a ffe09000.usb: USB3 ports: 1 <4>[ 1.807304] dwc2 ff400000.usb: supply vusb_d not found, using dummy regulator <4>[ 1.810905] dwc2 ff400000.usb: supply vusb_a not found, using dummy regulator <6>[ 1.818326] dwc2 ff400000.usb: EPs: 7, dedicated fifos, 712 entries in SPRAM <6>[ 1.827503] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 1.831086] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 <6>[ 1.839028] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228fe6c hci version 0x110 quirks 0x0000002000010010 <6>[ 1.848517] xhci-hcd xhci-hcd.0.auto: irq 38, io mem 0xff500000 <6>[ 1.855275] hub 1-0:1.0: USB hub found <6>[ 1.858594] hub 1-0:1.0: 2 ports detected <6>[ 1.863072] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 1.868497] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 <6>[ 1.876342] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed <6>[ 1.883120] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 1.891808] hub 2-0:1.0: USB hub found <6>[ 1.895335] hub 2-0:1.0: 1 port detected <6>[ 1.900237] pca953x 0-0020: using no AI <6>[ 1.913600] meson-gx-mmc ffe07000.mmc: allocated mmc-pwrseq <6>[ 1.916565] VCC_1V8: supplied by VCC_3V3 <6>[ 2.099546] mmc0: new HS200 MMC card at address 0001 <6>[ 2.100146] mmcblk0: mmc0:0001 AJTD4R 14.6 GiB <6>[ 2.104143] mmcblk0boot0: mmc0:0001 AJTD4R partition 1 4.00 MiB <6>[ 2.110253] mmcblk0boot1: mmc0:0001 AJTD4R partition 2 4.00 MiB <6>[ 2.116285] mmcblk0rpmb: mmc0:0001 AJTD4R partition 3 4.00 MiB, chardev (234:0) <6>[ 2.120393] usb 1-1: new high-speed USB device number 2 using xhci-hcd <6>[ 2.126442] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 <6>[ 2.331258] hub 1-1:1.0: USB hub found <6>[ 2.331343] hub 1-1:1.0: 4 ports detected <6>[ 14.220571] ALSA device list: <6>[ 14.220602] No soundcards found. <6>[ 14.229363] Freeing unused kernel memory: 5952K <6>[ 14.229531] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 14.290645] udevd[177]: starting version 3.2.9 <5>[ 14.291346] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 14.296660] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 14.303140] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 14.314102] udevd[177]: specified user 'tss' unknown <27>[ 14.315060] udevd[177]: specified group 'tss' unknown <30>[ 14.321783] udevd[178]: starting eudev-3.2.9 <6>[ 14.525772] input: adc-keys as /devices/platform/adc-keys/input/input0 <6>[ 14.638642] meson-drm ff900000.vpu: Queued 2 outputs on vpu <6>[ 14.714740] panfrost ffe40000.gpu: clock rate = 24000000 <3>[ 14.714853] panfrost ffe40000.gpu: dev_pm_opp_set_regulators: no regulator (mali) found: -19 <6>[ 14.720810] meson-vrtc ff8000a8.rtc: registered as rtc0 <6>[ 14.733651] meson8b-dwmac ff3f0000.ethernet: IRQ eth_wake_irq not found <6>[ 14.735548] meson8b-dwmac ff3f0000.ethernet: IRQ eth_lpi not found <6>[ 14.745123] panfrost ffe40000.gpu: [drm:panfrost_devfreq_init [panfrost]] Failed to register cooling device <6>[ 14.756440] meson-vrtc ff8000a8.rtc: setting system clock to 1970-01-01T00:00:14 UTC (14) <6>[ 14.767858] VDDCPU: supplied by regulator-dummy <6>[ 14.787971] meson-gx-mmc ffe03000.sd: allocated mmc-pwrseq <6>[ 14.790042] meson8b-dwmac ff3f0000.ethernet: PTP uses main clock <6>[ 14.792620] panfrost ffe40000.gpu: mali-g31 id 0x7093 major 0x0 minor 0x0 status 0x0 <6>[ 14.802281] meson8b-dwmac ff3f0000.ethernet: no reset control found <6>[ 14.803053] panfrost ffe40000.gpu: features: 00000000,3fde77ff, issues: 00000000,00000400 <6>[ 14.808221] meson-drm ff900000.vpu: CVBS Output connector not available <6>[ 14.816472] meson8b-dwmac ff3f0000.ethernet: User ID: 0x11, Synopsys ID: 0x37 <6>[ 14.826168] panfrost ffe40000.gpu: Features: L2:0x07100206 Shader:0x00000000 Tiler:0x00000209 Mem:0x1 MMU:0x00002821 AS:0xff JS:0x7 <6>[ 14.843868] panfrost ffe40000.gpu: shader_present=0x1 l2_present=0x1 <6>[ 14.851450] meson8b-dwmac ff3f0000.ethernet: DWMAC1000 <6>[ 14.852681] meson-dw-hdmi ff600000.hdmi-tx: Detected HDMI TX controller v2.01a with HDCP (meson_dw_hdmi_phy) <6>[ 14.856661] meson8b-dwmac ff3f0000.ethernet: DMA HW capability register supported <6>[ 14.876158] meson8b-dwmac ff3f0000.ethernet: RX Checksum Offload Engine supported <6>[ 14.880830] [drm] Initialized panfrost 1.1.0 20180908 for ffe40000.gpu on minor 0 <6>[ 14.882667] meson8b-dwmac ff3f0000.ethernet: COE Type 2 <6>[ 14.889008] meson-dw-hdmi ff600000.hdmi-tx: registered DesignWare HDMI I2C bus driver <6>[ 14.912656] meson8b-dwmac ff3f0000.ethernet: TX Checksum insertion supported <4>[ 14.927925] mmc2: queuing unknown CIS tuple 0x80 (2 bytes) <4>[ 14.930219] mmc2: queuing unknown CIS tuple 0x80 (3 bytes) <4>[ 14.936434] mmc2: queuing unknown CIS tuple 0x80 (3 bytes) <4>[ 14.943291] mmc2: queuing unknown CIS tuple 0x80 (7 bytes) <4>[ 14.949880] mmc2: queuing unknown CIS tuple 0x81 (9 bytes) <4>[ 14.955489] mmc2: queuing unknown CIS tuple 0x8e (9 bytes) <6>[ 14.968425] meson8b-dwmac ff3f0000.ethernet: Wake-Up On Lan supported <6>[ 14.970973] meson8b-dwmac ff3f0000.ethernet: Normal descriptors <6>[ 14.976451] Registered IR keymap rc-khadas <6>[ 14.980982] meson8b-dwmac ff3f0000.ethernet: Ring mode enabled <6>[ 14.989155] meson8b-dwmac ff3f0000.ethernet: Enable RX Mitigation via HW Watchdog Timer <6>[ 14.990892] meson-drm ff900000.vpu: bound ff600000.hdmi-tx (ops meson_dw_hdmi_ops [meson_dw_hdmi]) <6>[ 15.003918] Bluetooth: Core ver 2.22 <6>[ 15.005010] [drm] Initialized meson 1.0.0 20161109 for ff900000.vpu on minor 1 <6>[ 15.007310] NET: Registered protocol family 31 <6>[ 15.019450] Bluetooth: HCI device and connection manager initialized <6>[ 15.025934] Bluetooth: HCI socket layer initialized <6>[ 15.031000] Bluetooth: L2CAP socket layer initialized <6>[ 15.031022] Bluetooth: SCO socket layer initialized <3>[ 15.032433] rc_core: Loaded IR protocol module ir-nec-decoder, but protocol nec still not available <6>[ 15.032507] rc rc0: meson-ir as /devices/platform/soc/ff800000.bus/ff808000.ir/rc/rc0 <6>[ 15.032683] input: meson-ir as /devices/platform/soc/ff800000.bus/ff808000.ir/rc/rc0/input1 <6>[ 15.033235] meson-ir ff808000.ir: receiver initialized <6>[ 15.048107] Bluetooth: HCI UART driver ver 2.3 <6>[ 15.048114] Bluetooth: HCI UART protocol H4 registered <6>[ 15.048277] Bluetooth: HCI UART protocol LL registered <4>[ 15.048926] hci_uart_bcm serial0-0: supply vbat not found, using dummy regulator <4>[ 15.049057] hci_uart_bcm serial0-0: supply vddio not found, using dummy regulator <6>[ 15.049248] Bluetooth: HCI UART protocol Broadcom registered <6>[ 15.049290] Bluetooth: HCI UART protocol QCA registered <6>[ 15.075932] mmc2: new ultra high speed SDR50 SDIO card at address 0001 <5>[ 15.084112] cfg80211: Loading compiled-in X.509 certificates for regulatory database <5>[ 15.103045] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' <4>[ 15.103124] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 <4>[ 15.103129] platform regulatory.0: Falling back to sysfs fallback for: regulatory.db <6>[ 15.197175] Console: switching to colour frame buffer device 128x48 <6>[ 15.346132] meson-drm ff900000.vpu: [drm] fb0: mesondrmfb frame buffer device <6>[ 15.356974] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4359-sdio for chip BCM4359/9 <4>[ 15.362241] brcmfmac mmc2:0001:1: Direct firmware load for brcm/brcmfmac4359-sdio.bin failed with error -2 <4>[ 15.372056] brcmfmac mmc2:0001:1: Falling back to sysfs fallback for: brcm/brcmfmac4359-sdio.bin done Saving random seed: <6>[ 15.409025] Bluetooth: hci0: BCM: chip id 121 <6>[ 15.409343] Bluetooth: hci0: BCM: features 0x0e <5>[ 15.410535] random: dd: uninitialized urandom read (32 bytes read) <6>[ 15.414335] Bluetooth: hci0: BCM4359C0 <6>[ 15.423120] Bluetooth: hci0: BCM4359C0 (003.001.006) build 0000 OK Starting network: OK Starting dropbear sshd: <5>[ 15.466496] random: dropbear: uninitialized urandom read (32 bytes read) <6>[ 15.485890] NET: Registered protocol family 10 <6>[ 15.486635] Segment Routing with IPv6 OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-2847804/environment . /lava-2847804/environment / # /lava-2847804/bin/lava-test-runner /lava-2847804/0 /lava-2847804/bin/lava-test-runner /lava-2847804/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-2847804/0/tests/0_dmesg + cat uuid + UUID=2847804_1.5.2.4.1<8>[ 16.080724] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 16.102854] <8>[ 16.119259] <8>[ 16.136206] + set +x <8>[ 16.140939] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-2847804/environment / # . /lava-2847804/environment/lava-2847804/bin/lava-test-runner /lava-2847804/1 / # /lava-2847804/bin/lava-test-runner /lava-2847804/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-2847804/1/tests/1_bootrr + cat uuid + UUID=284780<8>[ 16.615192] 4_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/helpers:/lava-2847804/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr + sh helpers/bootrr-auto /lava-2847804/1/../bin/lava-test-case <8>[ 17.637457] /lava-2847804/1/../bin/lava-test-case <8>[ 17.654349] /lava-2847804/1/../bin/lava-test-case <8>[ 17.665757] + set +x <8>[ 17.674381] / #