[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.0 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected sst25vf016b with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 6 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.101.100 (3 ms) => setenv serverip 192.168.101.1 setenv serverip 192.168.101.1 => tftp 0x10000000 8435997/tftp-deploy-t2e_akzk/kernel/zImage tftp 0x10000000 8435997/tftp-deploy-t2e_akzk/kernel/zImage Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.100 Filename '8435997/tftp-deploy-t2e_akzk/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################# 2.5 MiB/s done Bytes transferred = 12341760 (bc5200 hex) => tftp 0x14000000 8435997/tftp-deploy-t2e_akzk/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 8435997/tftp-deploy-t2e_akzk/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.100 Filename '8435997/tftp-deploy-t2e_akzk/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############ 2.8 MiB/s done Bytes transferred = 15430946 (eb7522 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 8435997/tftp-deploy-t2e_akzk/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 8435997/tftp-deploy-t2e_akzk/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.100 Filename '8435997/tftp-deploy-t2e_akzk/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 1.6 MiB/s done Bytes transferred = 42449 (a5d1 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.101.1:/var/lib/lava/dispatcher/tmp/8435997/extract-nfsrootfs-i_v_w_gd,tcp,hard ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.101.1:/var/lib/lava/dispatcher/tmp/8435997/extract-nfsrootfs-i_v_w_gd,tcp,hard ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0xbc5200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 15430882 Bytes = 14.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d5d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.161-cip22 (KernelCI@build-j734028-arm-gcc-10-multi-v7-defconfig-kselftest-ts5th) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Dec 21 19:17:39 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 21 pages/cpu s55468 r8192 d22356 u86016 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.101.1:/var/lib/lava/dispatcher/tmp/8435997/extract-nfsrootfs-i_v_w_gd,tcp,hard ip=dhcp [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 921452K/1048576K available (17408K kernel code, 2651K rwdata, 8100K rodata, 2048K init, 6692K bss, 61588K reserved, 65536K cma-reserved, 196608K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] ftrace: allocating 55442 entries in 163 pages [ 0.000000] ftrace: allocated 163 pages with 4 groups [ 0.000000] Running RCU self tests [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU lockdep checking is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] L2C-310 errata 752271 769419 enabled [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 [ 0.000000] Switching to timer-based delay loop, resolution 15ns [ 0.000008] sched_clock: 32 bits at 66MHz, resolution 15ns, wraps every 32537631224ns [ 0.000039] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 28958491609 ns [ 0.004520] Console: colour dummy device 80x30 [ 0.004586] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.004615] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.004642] ... MAX_LOCK_DEPTH: 48 [ 0.004668] ... MAX_LOCKDEP_KEYS: 8192 [ 0.004693] ... CLASSHASH_SIZE: 4096 [ 0.004719] ... MAX_LOCKDEP_ENTRIES: 32768 [ 0.004745] ... MAX_LOCKDEP_CHAINS: 65536 [ 0.004771] ... CHAINHASH_SIZE: 32768 [ 0.004796] memory used by lock dependency info: 4061 kB [ 0.004821] memory used for stack traces: 2112 kB [ 0.004846] per task-struct memory footprint: 1536 bytes [ 0.004945] Calibrating delay loop (skipped), value calculated using timer frequency.. 132.00 BogoMIPS (lpj=660000) [ 0.004998] pid_max: default: 32768 minimum: 301 [ 0.005386] LSM: Security Framework initializing [ 0.005499] LSM support for eBPF active [ 0.005645] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.005695] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.008257] CPU: Testing write buffer coherency: ok [ 0.008377] CPU0: Spectre v2: using BPIALL workaround [ 0.009470] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.013401] Setting up static identity map for 0x10300000 - 0x103000ac [ 0.015828] rcu: Hierarchical SRCU implementation. [ 0.025486] EFI services will not be available. [ 0.026806] smp: Bringing up secondary CPUs ... [ 0.030176] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.030192] CPU1: Spectre v2: using BPIALL workaround [ 0.034260] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.034274] CPU2: Spectre v2: using BPIALL workaround [ 0.038001] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.038017] CPU3: Spectre v2: using BPIALL workaround [ 0.039171] smp: Brought up 1 node, 4 CPUs [ 0.039215] SMP: Total of 4 processors activated (528.00 BogoMIPS). [ 0.039252] CPU: All CPU(s) started in SVC mode. [ 0.041877] devtmpfs: initialized [ 0.099342] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.102010] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.102088] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.106857] pinctrl core: initialized pinctrl subsystem [ 0.113881] DMI not present or invalid. [ 0.116254] NET: Registered protocol family 16 [ 0.127868] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.137456] thermal_sys: Registered thermal governor 'step_wise' [ 0.138010] cpuidle: using governor menu [ 0.138534] CPU identified as i.MX6Q, silicon rev 1.0 [ 0.894256] vdd1p1: supplied by regulator-dummy [ 0.926439] vdd3p0: supplied by regulator-dummy [ 0.958160] vdd2p5: supplied by regulator-dummy [ 0.990143] vddarm: supplied by regulator-dummy [ 1.022831] vddpu: supplied by regulator-dummy [ 1.053631] vddsoc: supplied by regulator-dummy [ 2.401371] No ATAGs? [ 2.402127] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 2.402208] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 2.422534] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver [ 2.453011] Serial: AMBA PL011 UART driver [ 2.518900] Kprobes globally optimized [ 2.639392] iommu: Default domain type: Translated [ 2.641610] vgaarb: loaded [ 2.646500] SCSI subsystem initialized [ 2.648737] usbcore: registered new interface driver usbfs [ 2.649071] usbcore: registered new interface driver hub [ 2.649315] usbcore: registered new device driver usb [ 2.657081] i2c i2c-0: IMX I2C adapter registered [ 2.664181] i2c i2c-1: IMX I2C adapter registered [ 2.668795] i2c i2c-2: IMX I2C adapter registered [ 2.673498] pps_core: LinuxPPS API ver. 1 registered [ 2.673540] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 2.673641] PTP clock support registered [ 2.691841] clocksource: Switched to clocksource mxc_timer1 [ 4.434564] NET: Registered protocol family 2 [ 4.435402] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 4.438902] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 22528 bytes, linear) [ 4.439086] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 4.439313] TCP bind hash table entries: 8192 (order: 6, 327680 bytes, linear) [ 4.440751] TCP: Hash tables configured (established 8192 bind 8192) [ 4.441964] MPTCP token hash table entries: 1024 (order: 3, 49152 bytes, linear) [ 4.442318] UDP hash table entries: 512 (order: 3, 49152 bytes, linear) [ 4.442581] UDP-Lite hash table entries: 512 (order: 3, 49152 bytes, linear) [ 4.443335] NET: Registered protocol family 1 [ 4.446267] RPC: Registered named UNIX socket transport module. [ 4.446360] RPC: Registered udp transport module. [ 4.446401] RPC: Registered tcp transport module. [ 4.446442] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 4.446494] NET: Registered protocol family 44 [ 4.446563] PCI: CLS 0 bytes, default 64 [ 4.449047] Trying to unpack rootfs image as initramfs... [ 6.353752] Freeing initrd memory: 15072K [ 6.354880] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 6.356081] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 6.365345] Initialise system trusted keyrings [ 6.366541] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 6.417684] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 6.421917] NFS: Registering the id_resolver key type [ 6.422286] Key type id_resolver registered [ 6.422378] Key type id_legacy registered [ 6.423041] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 6.423146] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 6.423341] ntfs: driver 2.1.32 [Flags: R/O]. [ 6.425625] Key type asymmetric registered [ 6.425751] Asymmetric key parser 'x509' registered [ 6.426206] bounce: pool size: 64 pages [ 6.426393] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 6.426498] io scheduler mq-deadline registered [ 6.426542] io scheduler kyber registered [ 6.427456] test_firmware: interface ready [ 6.614921] mxs-dma 110000.dma-apbh: initialized [ 6.682477] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 6.682737] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 6.956049] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 6.977433] SuperH (H)SCI(F) driver initialized [ 6.980463] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX [ 6.985835] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX [ 7.917850] printk: console [ttymxc1] enabled [ 7.928867] msm_serial: driver initialized [ 7.934206] STMicroelectronics ASC driver initialized [ 7.946189] STM32 USART driver initialized [ 7.973275] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 0 [ 7.996199] panel-simple panel-lcd: supply power not found, using dummy regulator [ 8.004709] panel-simple panel-lcd: Specify missing connector_type [ 8.012897] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 8.068840] brd: module loaded [ 8.131623] loop: module loaded [ 8.138300] lkdtm: No crash points registered, enable through debugfs [ 8.161224] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 [ 8.169274] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 [ 8.177387] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 [ 8.185670] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 [ 8.193743] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator [ 8.202075] ahci-imx 2200000.sata: supply phy not found, using dummy regulator [ 8.209827] ahci-imx 2200000.sata: supply target not found, using dummy regulator [ 8.221240] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled [ 8.228370] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 8.237269] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 8.251715] scsi host0: ahci-imx [ 8.257445] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 [ 8.325914] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 8.339741] pps pps0: new PPS source ptp0 [ 8.385786] fec 2188000.ethernet eth0: registered PHC device 0 [ 8.396723] e1000e: Intel(R) PRO/1000 Network Driver [ 8.401800] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 8.408008] igb: Intel(R) Gigabit Ethernet Network Driver [ 8.413500] igb: Copyright (c) 2007-2014 Intel Corporation. [ 8.442644] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 8.450247] usbcore: registered new interface driver pegasus [ 8.456212] usbcore: registered new interface driver asix [ 8.461854] usbcore: registered new interface driver ax88179_178a [ 8.468127] usbcore: registered new interface driver cdc_ether [ 8.474291] usbcore: registered new interface driver smsc75xx [ 8.480331] usbcore: registered new interface driver smsc95xx [ 8.486326] usbcore: registered new interface driver net1080 [ 8.492226] usbcore: registered new interface driver cdc_subset [ 8.498321] usbcore: registered new interface driver zaurus [ 8.504248] usbcore: registered new interface driver cdc_ncm [ 8.523604] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 8.530250] ehci-pci: EHCI PCI platform driver [ 8.534941] ehci-platform: EHCI generic platform driver [ 8.541273] ehci-orion: EHCI orion driver [ 8.546364] SPEAr-ehci: EHCI SPEAr driver [ 8.551328] ehci-st: EHCI STMicroelectronics driver [ 8.557218] ehci-exynos: EHCI Exynos driver [ 8.562432] ehci-atmel: EHCI Atmel driver [ 8.567383] tegra-ehci: Tegra EHCI driver [ 8.572433] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 8.578778] ohci-pci: OHCI PCI platform driver [ 8.583475] ohci-platform: OHCI generic platform driver [ 8.589749] SPEAr-ohci: OHCI SPEAr driver [ 8.594779] ohci-st: OHCI STMicroelectronics driver [ 8.600613] ohci-atmel: OHCI Atmel driver [ 8.604767] ata1: SATA link down (SStatus 0 SControl 300) [ 8.608436] usbcore: registered new interface driver usb-storage [ 8.610561] ahci-imx 2200000.sata: no device found, disabling link. [ 8.622774] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug [ 8.651068] i2c /dev entries driver [ 8.742628] sdhci: Secure Digital Host Controller Interface driver [ 8.748851] sdhci: Copyright(c) Pierre Ossman [ 8.763557] Synopsys Designware Multimedia Card Interface Driver [ 8.777514] sdhci-pltfm: SDHCI platform and OF driver helper [ 8.787100] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO [ 8.787106] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO [ 8.797425] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO [ 8.804220] ledtrig-cpu: registered to indicate activity on CPUs [ 8.814302] usbcore: registered new interface driver usbhid [ 8.819916] usbhid: USB HID core driver [ 8.825753] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA [ 8.838427] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA [ 8.850234] ipip: IPv4 and MPLS over IPv4 tunneling driver [ 8.858464] gre: GRE over IPv4 demultiplexor driver [ 8.863468] ip_gre: GRE over IPv4 tunneling driver [ 8.874483] IPv4 over IPsec tunneling driver [ 8.884236] NET: Registered protocol family 10 [ 8.886187] mmc2: new high speed SDHC card at address 0001 [ 8.895842] Segment Routing with IPv6 [ 8.898668] mmcblk2: mmc2:0001 SD 14.6 GiB [ 8.906613] ip6_gre: GRE over IPv6 tunneling driver [ 8.915455] NET: Registered protocol family 17 [ 8.922153] Key type dns_resolver registered [ 8.940039] ThumbEE CPU extension supported. [ 8.944483] Registering SWP/SWPB emulation handler [ 8.950857] Loading compiled-in X.509 certificates [ 8.977941] GPT:Primary header thinks Alt. header is not at the end of the disk. [ 8.985573] GPT:29296874 != 30560255 [ 8.989193] GPT:Alternate GPT header not at the end of the disk. [ 8.995359] GPT:29296874 != 30560255 [ 8.998978] GPT: Use GNU Parted to correct GPT errors. [ 9.004292] mmcblk2: p1 p2 p3 [ 9.185413] panel-simple panel-lcd: supply power not found, using dummy regulator [ 9.194088] panel-simple panel-lcd: Specify missing connector_type [ 9.209758] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 9.267709] imx_usb 2184200.usb: No over current polarity defined [ 9.282139] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 9.287448] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 [ 9.322486] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 9.343439] hub 1-0:1.0: USB hub found [ 9.349422] hub 1-0:1.0: 1 port detected [ 9.367653] imx_thermal 20c8000.anatop:tempmon: invalid sensor calibration data [ 9.375115] imx_thermal 20c8000.anatop:tempmon: error -EINVAL: failed to init from nvmem [ 9.383584] imx_thermal: probe of 20c8000.anatop:tempmon failed with error -22 [ 9.417942] panel-simple panel-lcd: supply power not found, using dummy regulator [ 9.426500] panel-simple panel-lcd: Specify missing connector_type [ 9.442286] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 9.480903] panel-simple panel-lcd: supply power not found, using dummy regulator [ 9.489453] panel-simple panel-lcd: Specify missing connector_type [ 9.505071] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 9.527605] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 9.564365] panel-simple panel-lcd: supply power not found, using dummy regulator [ 9.572920] panel-simple panel-lcd: Specify missing connector_type [ 9.588619] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 9.613642] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:06: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:06, irq=POLL) [ 9.629342] IP-Config: Failed to open gretap0 [ 9.633884] IP-Config: Failed to open erspan0 [ 9.662023] Sending DHCP requests . [ 9.782356] usb 1-1: new high-speed USB device number 2 using ci_hdrc [ 10.001374] hub 1-1:1.0: USB hub found [ 10.006124] hub 1-1:1.0: 3 ports detected [ 10.048183] panel-simple panel-lcd: supply power not found, using dummy regulator [ 10.056731] panel-simple panel-lcd: Specify missing connector_type [ 10.072465] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 11.753468] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx [ 11.762199] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 11.781899] ., OK [ 11.824430] IP-Config: Got DHCP answer from 192.168.101.1, my address is 192.168.101.100 [ 11.832975] IP-Config: Complete: [ 11.836282] device=eth0, hwaddr=0e:cc:7b:b0:7c:c7, ipaddr=192.168.101.100, mask=255.255.255.0, gw=192.168.101.1 [ 11.846948] host=imx6q-sabrelite-cbg-1, domain=lava.cbg.collabora.co.uk, nis-domain=(none) [ 11.855779] bootserver=192.168.101.1, rootserver=192.168.101.1, rootpath= [ 11.855805] nameserver0=192.168.101.1 [ 11.930508] Freeing unused kernel memory: 2048K [ 11.942906] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u1 [ 17.019172] imx-ipuv3 2400000.ipu: IPUv3H probed [ 17.068477] panel-simple panel-lcd: supply power not found, using dummy regulator [ 17.077117] panel-simple panel-lcd: Specify missing connector_type [ 17.086936] imx-ipuv3 2800000.ipu: IPUv3H probed [ 17.118767] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 17.168576] panel-simple panel-lcd: supply power not found, using dummy regulator [ 17.203256] panel-simple panel-lcd: Specify missing connector_type [ 17.207527] CAN device driver interface [ 17.218745] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 17.291207] panel-simple panel-lcd: supply power not found, using dummy regulator [ 17.299894] panel-simple panel-lcd: Specify missing connector_type [ 17.305902] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) [ 17.315166] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) [ 17.321528] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 17.342834] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) [ 17.351648] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) [ 17.393908] caam 2100000.crypto: Entropy delay = 3200 [ 17.409302] panel-simple panel-lcd: supply power not found, using dummy regulator [ 17.419533] panel-simple panel-lcd: Specify missing connector_type [ 17.435556] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 17.459803] caam 2100000.crypto: Instantiated RNG4 SH0 [ 17.520563] caam 2100000.crypto: Instantiated RNG4 SH1 [ 17.525861] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) [ 17.532620] caam 2100000.crypto: job rings = 2, qi = 0 [ 17.565318] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) [ 17.586739] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) [ 17.602319] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) [ 17.608919] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 [ 17.643849] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 [ 17.652058] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 [ 17.655233] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator [ 17.658204] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 [ 17.667699] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 1 [ 17.673657] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests [ 17.688709] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator [ 17.700909] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests [ 17.712548] sgtl5000 0-000a: sgtl5000 revision 0x11 [ 17.727531] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) [ 17.736592] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) [ 17.736600] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum [ 17.753027] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) [ 17.761665] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) [ 17.831398] panel-simple panel-lcd: supply power not found, using dummy regulator [ 17.842308] panel-simple panel-lcd: Specify missing connector_type [ 17.879625] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 17.936931] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) [ 17.945754] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) [ 17.954863] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) [ 17.964031] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) [ 17.995460] panel-simple panel-lcd: supply power not found, using dummy regulator [ 18.004129] panel-simple panel-lcd: Specify missing connector_type [ 18.020103] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 18.610031] caam algorithms registered in /proc/crypto [ 18.636841] caam 2100000.crypto: registering rng-caam [ 18.670097] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) [ 18.678773] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) [ 18.687572] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) [ 18.696158] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) [ 18.726007] panel-simple panel-lcd: supply power not found, using dummy regulator [ 18.735065] panel-simple panel-lcd: Specify missing connector_type [ 18.750714] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 18.795578] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) [ 18.804300] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) [ 18.812950] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) [ 18.821430] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) [ 18.830389] random: crng init done Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/erspan0 found done. IP-Config: erspan0 hardware address 00:00:00:00:00:00 mtu 1450 DHCP SIOCSIFFLAGS: Cannot assign requested address IP-Config: gretap0 hardware address 00:00:00:00:00:00 mtu 1462 DHCP SIOCSIFFLAGS: Cannot assign requested address IP-Config: eth0 hardware address 0e:cc:7b:b0:7c:c7 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.101.1): address: 192.168.101.100 broadcast: 192.168.101.255 netmask: 255.255.255.0 gateway: 192.168.101.1 dns0 : 192.168.101.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-cbg-1 domain : lava.cbg.collabora.co.uk rootserver: 192.168.101.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 22.357657] systemd[1]: System time before build time, advancing clock. [ 22.669649] systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) [ 22.696294] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! [ 22.779680] systemd[1]: Set hostname to . [ 24.805314] systemd[1]: Queued start job for default target Graphical Interface. [ 24.821191] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. [ 24.867441] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. [ 24.917511] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 24.966670] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 25.016563] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. [ 25.065623] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. [ 25.113558] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. [ 25.127483] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. [ 25.173738] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. [ 25.213115] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 25.253905] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. [ 25.294149] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 25.334430] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. [ 25.445674] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. [ 25.463667] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 25.529327] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 25.579918] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. [ 25.638449] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 25.687743] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 25.737527] systemd[1]: Condition check resulted in Huge Pages File System being skipped. [ 25.747920] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. [ 25.771034] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... [ 25.830625] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... [ 25.891445] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... [ 25.947199] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... [ 25.995850] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... [ 26.045252] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... [ 26.102099] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. [ 26.133904] fuse: init (API version 7.32) [ 26.137913] systemd[1]: Starting Journal Service... Starting Journal Service... [ 26.209438] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 26.274308] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... [ 26.334155] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... [ 26.382962] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. [ 26.435675] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. [ 26.495167] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. [ 26.621067] systemd[1]: modprobe@configfs.service: Succeeded. [ 26.632962] systemd[1]: Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module configfs. [ 26.689701] systemd[1]: modprobe@drm.service: Succeeded. [ 26.701068] systemd[1]: Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module drm. [ 26.759452] systemd[1]: modprobe@fuse.service: Succeeded. [ 26.771569] systemd[1]: Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Module fuse. [ 26.829235] systemd[1]: Finished Load Kernel Modules. [ OK ] Finished Load Kernel Modules. [ 26.879145] systemd[1]: Finished Remount Root and Kernel File Systems. [ OK ] Finished Remount Root and Kernel File Systems. [ 26.937419] systemd[1]: Mounting FUSE Control File System... Mounting FUSE Control File System... [ 26.993694] systemd[1]: Mounting Kernel Configuration File System... Mounting Kernel Configuration File System... [ 27.054625] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped. [ 27.065234] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped. [ 27.088034] systemd[1]: Starting Load/Save Random Seed... Starting Load/Save Random Seed... [ 27.145291] systemd[1]: Starting Apply Kernel Variables... Starting Apply Kernel Variables... [ 27.204982] systemd[1]: Starting Create System Users... Starting Create System Users... [ 27.235652] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Mounted FUSE Control File System. [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. Starting Flush Journal to Persistent Storage... [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ 27.649793] systemd-journald[280]: Received client request to flush runtime journal. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Rule-based Manage…for Device Events and Files... [ OK ] Finished Flush Journal to Persistent Storage. Starting Create Volatile Files and Directories... [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... [ OK ] Started Network Service. [ OK ] Finished Create Volatile Files and Directories. Starting Network Name Resolution... Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Found device /dev/ttymxc1. [ OK ] Finished Coldplug All udev Devices. [ OK ] Reached target System Initialization. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Started Network Name Resolution. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [* ] A start job is running for User Login Management (13s / 1min 41s) M [** ] A start job is running for User Login Management (14s / 1min 41s) M [*** ] A start job is running for User Login Management (14s / 1min 41s) M [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 5.10.161-cip22 #1 SMP Wed Dec 21 19:17:39 UTC 2022 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/8435997/extract-nfsrootfs-i_v_w_gd' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/8435997/extract-nfsrootfs-i_v_w_gd' / # export NFS_SERVER_IP='192.168.101.1' export NFS_SERVER_IP='192.168.101.1' / # # # / # export SHELL=/bin/bash export SHELL=/bin/bash / # . /lava-8435997/environment . /lava-8435997/environment / # /lava-8435997/bin/lava-test-runner /lava-8435997/0 /lava-8435997/bin/lava-test-runner /lava-8435997/0 + export TESTRUN_ID=0_timesync-off + TESTRUN_ID=0_timesync-off + cd /lava-8435997/0/tests/0_timesync-off ++ cat uuid + UUID=8435997_1.6.2.4.1 + set +x + systemctl stop systemd-timesyncd + set +x + export TESTRUN_ID=1_kselftest-livepatch + TESTRUN_ID=1_kselftest-livepatch + cd /lava-8435997/0/tests/1_kselftest-livepatch ++ cat uuid + UUID=8435997_1.6.2.4.5 + set +x + cd ./automated/linux/kselftest/ + ./kselftest.sh -c livepatch -T '' -t kselftest_armhf.tar.gz -s false -u http://storage.kernelci.org/cip-gitlab/ci-iwamatsu-linux-5.10.y-cip-rc/v5.10.158-cip22-142-g79bb6f9db05d/arm/multi_v7_defconfig+kselftest/gcc-10/kselftest.tar.xz -L '' -S skipfile-lkft.yaml -b imx6q-sabrelite -g cip-gitlab -e '' -p /opt/kselftests/mainline/ -n 1 -i 1 INFO: Generating a skipfile based on /lava-8435997/0/tests/1_kselftest-livepatch/automated/linux/kselftest/skipfile-lkft.yaml INFO: Using the following generated skipfile contents (until EOF): breakpoints:breakpoint_test breakpoints:step_after_suspend_test ftrace:ftracetest net:rtnetlink.sh net:tls netfilter:bridge_brouter.sh netfilter:nft_flowtable.sh netfilter:nft_trans_stress.sh pidfd:pidfd_wait INFO: EOF INFO: Installing sed perl wget xz-utils iproute2 Get:1 http://deb.debian.org/debian bullseye InRelease [116 kB] Get:2 http://deb.debian.org/debian bullseye/main armhf Packages [7945 kB] Get:3 http://deb.debian.org/debian bullseye/main Translation-en [6240 kB] Fetched 14.3 MB in 31s (459 kB/s) Reading package lists... Reading package lists... Building dependency tree... Reading state information... iproute2 is already the newest version (5.10.0-4). perl is already the newest version (5.32.1-4+deb11u2). sed is already the newest version (4.7-1). wget is already the newest version (1.21-1+deb11u1). xz-utils is already the newest version (5.2.5-2.1~deb11u1). 0 upgraded, 0 newly installed, 0 to remove and 17 not upgraded. --2022-12-21 19:33:47-- http://storage.kernelci.org/cip-gitlab/ci-iwamatsu-linux-5.10.y-cip-rc/v5.10.158-cip22-142-g79bb6f9db05d/arm/multi_v7_defconfig+kselftest/gcc-10/kselftest.tar.xz Resolving storage.kernelci.org (storage.kernelci.org)... 52.250.1.28 Connecting to storage.kernelci.org (storage.kernelci.org)|52.250.1.28|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1407556 (1.3M) [application/octet-stream] Saving to: 'kselftest.tar.xz' kselftest.tar.xz 0%[ ] 0 --.-KB/s kselftest.tar.xz 3%[ ] 44.98K 159KB/s kselftest.tar.xz 14%[=> ] 193.46K 303KB/s kselftest.tar.xz 35%[======> ] 494.65K 573KB/s kselftest.tar.xz 54%[=========> ] 753.42K 703KB/s kselftest.tar.xz 68%[============> ] 941.50K 726KB/s kselftest.tar.xz 89%[================> ] 1.20M 817KB/s kselftest.tar.xz 100%[===================>] 1.34M 855KB/s in 1.6s 2022-12-21 19:33:49 (855 KB/s) - 'kselftest.tar.xz' saved [1407556/1407556] skiplist: ======================================== breakpoints:breakpoint_test breakpoints:step_after_suspend_test ftrace:ftracetest net:rtnetlink.sh net:tls netfilter:bridge_brouter.sh netfilter:nft_flowtable.sh netfilter:nft_trans_stress.sh pidfd:pidfd_wait ======================================== livepatch:test-livepatch.sh livepatch:test-callbacks.sh livepatch:test-shadow-vars.sh livepatch:test-state.sh livepatch:test-ftrace.sh ============== Tests to run =============== livepatch:test-livepatch.sh livepatch:test-callbacks.sh livepatch:test-shadow-vars.sh livepatch:test-state.sh livepatch:test-ftrace.sh ===========End Tests to run =============== [ 130.973924] kselftest: Running tests in livepatch TAP version 13 1..5 # selftests: livepatch: test-livepatch.sh [ 131.558311] livepatch: kernel.ftrace_enabled = 1 [ 131.670878] ===== TEST: basic function patching ===== # TEST: basic function patching ... [ 131.748242] SKIP: unable to load module test_klp_livepatch, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root SKIP: unable to load module test_klp_livepatch, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root ok 1 selftests: livepatch: test-livepatch.sh # SKIP # selftests: livepatch: test-callbacks.sh [ 132.312021] livepatch: kernel.ftrace_enabled = 1 # TEST: [ 132.402316] ===== TEST: target module before livepatch ===== target module before livepatch ... [ 132.462555] SKIP: unable to load module test_klp_callbacks_mod, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root SKIP: unable to load module test_klp_callbacks_mod, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root ok 2 selftests: livepatch: test-callbacks.sh # SKIP # selftests: livepatch: test-shadow-vars.sh [ 133.022621] livepatch: kernel.ftrace_enabled = 1 [ 133.111155] ===== TEST: basic shadow variable API ===== # TEST: basic shadow variable API ... [ 133.182707] SKIP: unable to load module test_klp_shadow_vars, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root SKIP: unable to load module test_klp_shadow_vars, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root ok 3 selftests: livepatch: test-shadow-vars.sh # SKIP # selftests: livepatch: test-state.sh [ 133.747569] livepatch: kernel.ftrace_enabled = 1 # TE[ 133.840116] ===== TEST: system state modification ===== ST: system state modification ... [ 133.899652] SKIP: unable to load module test_klp_state, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root SKIP: unable to load module test_klp_state, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root ok 4 selftests: livepatch: test-state.sh # SKIP # selftests: livepatch: test-ftrace.sh [ 134.473479] livepatch: kernel.ftrace_enabled = 1 # TEST: livepatch interaction with ftrace_enabled [ 134.566664] ===== TEST: livepatch interaction with ftrace_enabled sysctl ===== sysctl ... [ 134.638836] livepatch: kernel.ftrace_enabled = 0 [ 134.644511] % modprobe test_klp_livepatch [ 134.710385] modprobe: FATAL: Module test_klp_livepatch not found in directory /lib/modules/5.10.161-cip22 [ 134.786219] livepatch: kernel.ftrace_enabled = 1 [ 134.850707] SKIP: unable to load module test_klp_livepatch, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root SKIP: unable to load module test_klp_livepatch, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root ok 5 selftests: livepatch: test-ftrace.sh # SKIP + ../../utils/send-to-lava.sh ./output/result.txt + set +x / #