Trying 10.1.1.35... Connected to potato3.baylibre. Escape character is '^]'. QA5:A;SVN:B72;POC:17F;STS:0;BOOT:0;INIT:10;BOOT:1;INIT:0;READ:0;CHECK:0;PASS:1; ----------------------------------------------------------------------- * Welcome to Hardkernel's ODROID-C... (Built at 19:33:00 Dec 8 2014) * ----------------------------------------------------------------------- CPU : AMLogic S805 MEM : 1024MB (DDR3@792MHz) BID : HKC1310001 S/N : HKC11122F37E0F97 0x0000009f check SD_boot_type:0x1 card_type:0x1 Loading U-boot...success. U-boot-00000-ge6d5633f1654(odroidc@odroidc-v2011.03) (Jan 22 2016 - 11:11:57) I2C: clear pinmux reg1[24]=0 clear pinmux reg1[1]=0 out reg=c1108058,value=fffcfa00 set output en 0xc1108054[21]=0 set output val 0xc1108058[21]=0 clear pinmux reg1[25]=0 clear pinmux reg8[12]=0 clear pinmux reg1[3]=0 clear pinmux reg1[2]=0 set output en 0xc1108054[20]=1 clear pinmux reg1[24]=0 clear pinmux reg1[1]=0 out reg=c1108058,value=fffcfa00 set output en 0xc1108054[21]=0 set output val 0xc1108058[21]=0 clear pinmux reg1[25]=0 clear pinmux reg8[12]=0 clear pinmux reg1[3]=0 clear pinmux reg1[2]=0 out reg=c1108058,value=fffcfa00 set output en 0xc1108054[20]=0 set output val 0xc1108058[20]=0 clear pinmux reg1[25]=0 clear pinmux reg8[12]=0 clear pinmux reg1[3]=0 clear pinmux reg1[2]=0 set output en 0xc1108054[20]=1 clear pinmux reg1[24]=0 clear pinmux reg1[1]=0 out reg=c1108058,value=ffdcfa00 set output en 0xc1108054[21]=0 set output val 0xc1108058[21]=0 clear pinmux reg1[24]=0 clear pinmux reg1[1]=0 out reg=c1108058,value=fffcfa00 set output en 0xc1108054[21]=0 set output val 0xc1108058[21]=0 clear pinmux reg1[24]=0 clear pinmux reg1[1]=0 out reg=c1108058,value=ffdcfa00 set output en 0xc1108054[21]=0 set output val 0xc1108058[21]=0 clear pinmux reg1[24]=0 clear pinmux reg1[1]=0 out reg=c1108058,value=fffcfa00 set output en 0xc1108054[21]=0 set output val 0xc1108058[21]=0 clear pinmux reg1[24]=0 clear pinmux reg1[1]=0 out reg=c1108058,value=ffdcfa00 set output en 0xc1108054[21]=0 set output val 0xc1108058[21]=0 clear pinmux reg1[24]=0 clear pinmux reg1[1]=0 out reg=c1108058,value=fffcfa00 set output en 0xc1108054[21]=0 set output val 0xc1108058[21]=0 clear pinmux reg1[24]=0 clear pinmux reg1[1]=0 out reg=c1108058,value=ffdcfa00 set output en 0xc1108054[21]=0 set output val 0xc1108058[21]=0 clear pinmux reg1[24]=0 clear pinmux reg1[1]=0 out reg=c1108058,value=fffcfa00 set output en 0xc1108054[21]=0 set output val 0xc1108058[21]=0 clear pinmux reg1[24]=0 clear pinmux reg1[1]=0 out reg=c1108058,value=ffdcfa00 set output en 0xc1108054[21]=0 set output val 0xc1108058[21]=0 clear pinmux reg1[24]=0 clear pinmux reg1[1]=0 out reg=c1108058,value=fffcfa00 set output en 0xc1108054[21]=0 set output val 0xc1108058[21]=0 clear pinmux reg1[24]=0 clear pinmux reg1[1]=0 out reg=c1108058,value=ffdcfa00 set output en 0xc1108054[21]=0 set output val 0xc1108058[21]=0 clear pinmux reg1[24]=0 clear pinmux reg1[1]=0 out reg=c1108058,value=fffcfa00 set output en 0xc1108054[21]=0 set output val 0xc1108058[21]=0 clear pinmux reg1[24]=0 clear pinmux reg1[1]=0 out reg=c1108058,value=ffdcfa00 set output en 0xc1108054[21]=0 set output val 0xc1108058[21]=0 clear pinmux reg1[24]=0 clear pinmux reg1[1]=0 out reg=c1108058,value=fffcfa00 set output en 0xc1108054[21]=0 set output val 0xc1108058[21]=0 clear pinmux reg1[24]=0 clear pinmux reg1[1]=0 out reg=c1108058,value=ffdcfa00 set output en 0xc1108054[21]=0 set output val 0xc1108058[21]=0 clear pinmux reg1[24]=0 clear pinmux reg1[1]=0 out reg=c1108058,value=fffcfa00 set output en 0xc1108054[21]=0 set output val 0xc1108058[21]=0 clear pinmux reg1[24]=0 clear pinmux reg1[1]=0 out reg=c1108058,value=ffdcfa00 set output en 0xc1108054[21]=0 set output val 0xc1108058[21]=0 clear pinmux reg1[24]=0 clear pinmux reg1[1]=0 out reg=c1108058,value=fffcfa00 set output en 0xc1108054[21]=0 set output val 0xc1108058[21]=0 clear pinmux reg1[24]=0 clear pinmux reg1[1]=0 out reg=c1108058,value=ffdcfa00 set output en 0xc1108054[21]=0 set output val 0xc1108058[21]=0 clear pinmux reg1[25]=0 clear pinmux reg8[12]=0 clear pinmux reg1[3]=0 clear pinmux reg1[2]=0 out reg=c1108058,value=ffccfa00 set output en 0xc1108054[20]=0 set output val 0xc1108058[20]=0 clear pinmux reg1[24]=0 clear pinmux reg1[1]=0 out reg=c1108058,value=ffecfa00 set output en 0xc1108054[21]=0 set output val 0xc1108058[21]=0 clear pinmux reg1[25]=0 clear pinmux reg8[12]=0 clear pinmux reg1[3]=0 clear pinmux reg1[2]=0 set output en 0xc1108054[20]=1 clear pinmux reg1[25]=0 clear pinmux reg8[12]=0 clear pinmux reg1[3]=0 clear pinmux reg1[2]=0 set output en 0xc1108054[20]=1 clear pinmux reg1[25]=0 clear pinmux reg8[12]=0 clear pinmux reg1[3]=0 clear pinmux reg1[2]=0 set output en 0xc1108054[20]=1 ready DRAM: 1 GiB relocation Offset is: 2ff18000 MMC: SDCARD: 0, eMMC: 1 IR init is done! vpu clk_level = 3 set vpu clk: 182150000Hz, readback: 182150000Hz(0x701) mode = 6 vic = 4 set HDMI vic: 4 mode is: 6 viu chan = 1 config HPLL config HPLL done reconfig packet setting done MMC read: dev # 0, block # 33984, count 12288 ... 12288 blocks read: OK There is no valid bmp file at the given address ============================================================ Vendor: Man 035344 Snr 000ebd07 Rev: 8.0 Prod: SS16G Type: Removable Hard Disk Capacity: 15193.5 MB = 14.8 GB (31116288 x 512) ------------------------------------------------------------ Partition Start Sector Num Sectors Type 1 2048 262144 c 2 264192 10702848 83 ============================================================ Net: Meson_Ethernet init suspend firmware done. (ret:0) Hit Enter key to stop autoboot -- : 1 tstc enter exit abortboot: 1 odroidc#setenv autoload no setenv autoload no odroidc#setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff odroidc#setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff odroidc#dhcp dhcp Amlogic Ethernet Init Success: reset mac OK!(0) ETH PHY hardware reset OK find net phy id=0x1cc916, phyad=0 set_mac_mode(0) final_addr[rx-tx]: 0x3ffec000-0x3ffec600 Ethernet reset OK MAC address is 00:1e:06:10:33:17 duplex 1000m BOOTP broadcast 1 duplex 1000m BOOTP broadcast 2 *** Unhandled DHCP Option in OFFER/ACK: 28 *** Unhandled DHCP Option in OFFER/ACK: 28 DHCP client bound to address 10.201.3.93 odroidc#setenv serverip 10.201.1.11 setenv serverip 10.201.1.11 odroidc#tftp 0x21000000 3158655/tftp-deploy-uihmy6dr/kernel/uImage tftp 0x21000000 3158655/tftp-deploy-uihmy6dr/kernel/uImage Using Meson_Ethernet device TFTP from server 10.201.1.11; our IP address is 10.201.3.93 Filename '3158655/tftp-deploy-uihmy6dr/kernel/uImage'. Load address: 0x21000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## done Bytes transferred = 9683520 (93c240 hex) odroidc#tftp 0x22000000 3158655/tftp-deploy-uihmy6dr/ramdisk/ramdisk.cpio.gz.uboot tftp 0x22000000 3158655/tftp-deploy-uihmy6dr/ramdisk/ramdisk.cpio.gz.uboot Using Meson_Ethernet device TFTP from server 10.201.1.11; our IP address is 10.201.3.93 Filename '3158655/tftp-deploy-uihmy6dr/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x22000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ###################################################### done Bytes transferred = 16057736 (f50588 hex) odroidc#setenv initrd_size ${filesize} setenv initrd_size ${filesize} odroidc#tftp 0x21f00000 3158655/tftp-deploy-uihmy6dr/dtb/meson8b-odroidc1.dtb tftp 0x21f00000 3158655/tftp-deploy-uihmy6dr/dtb/meson8b-odroidc1.dtb Using Meson_Ethernet device TFTP from server 10.201.1.11; our IP address is 10.201.3.93 Filename '3158655/tftp-deploy-uihmy6dr/dtb/meson8b-odroidc1.dtb'. Load address: 0x21f00000 Loading: *## done Bytes transferred = 19356 (4b9c hex) odroidc#setenv bootargs 'console=ttyAML0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttyAML0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' odroidc#bootm 0x21000000 0x22000000 0x21f00000 bootm 0x21000000 0x22000000 0x21f00000 ## Booting kernel from Legacy Image at 21000000 ... Image Name: Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 9683456 Bytes = 9.2 MiB Load Address: 00208000 Entry Point: 00208000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 22000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16057672 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 21f00000 Booting using the fdt blob at 0x21f00000 Loading Kernel Image ... OK OK uboot time: 16194181 us. Using machid 0xf81 from environment faild to get aml_reserved_end address the default relocate ramdisk and fdt address-relocate_addr: 0x20000000 Loading Device Tree to 1fff8000, end 1ffffb9b ... OK libfdt fdt_path_offset() returned FDT_ERR_NOTFOUND libfdt fdt_path_offset() returned FDT_ERR_NOTFOUND Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x200 [ 0.000000] Linux version 5.10.164-cip24 (KernelCI@build-j874491-arm-gcc-10-multi-v7-defconfig-pzp4p) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Jan 18 14:49:06 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [410fc051] revision 1 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Hardkernel ODROID-C1 [ 0.000000] earlycon: meson0 at MMIO 0xc81004c0 (options '115200n8') [ 0.000000] printk: bootconsole [meson0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x3c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x000000002fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000030000000-0x000000003fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x00000000001fffff] [ 0.000000] node 0: [mem 0x0000000000200000-0x000000003fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttyAML0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 931736K/1048576K available (13312K kernel code, 2232K rwdata, 5344K rodata, 2048K init, 427K bss, 51304K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] irq_meson_gpio: 119 to 8 gpio interrupt mux initialized <4>[ 0.000000] L2C: DT/platform modifies aux control register: 0x02060000 -> 0x32460000 <6>[ 0.000000] L2C-310 erratum 769419 enabled <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 1 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 8 ways, 512 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x4100a0c9, AUX_CTRL 0x36460000 <6>[ 0.000015] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483647500ns <6>[ 0.002994] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275 ns <6>[ 0.012541] Switching to timer-based delay loop, resolution 1000ns <6>[ 0.020824] Console: colour dummy device 80x30 <6>[ 0.023629] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=10000) <6>[ 0.034013] pid_max: default: 32768 minimum: 301 <6>[ 0.038972] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.046384] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.054893] CPU: Testing write buffer coherency: ok <6>[ 0.059689] CPU0: thread -1, cpu 0, socket 2, mpidr 80000200 <6>[ 0.066100] Setting up static identity map for 0x300000 - 0x3000ac <6>[ 0.072422] rcu: Hierarchical SRCU implementation. <6>[ 0.078296] EFI services will not be available. <6>[ 0.081798] smp: Bringing up secondary CPUs ... <6>[ 0.086910] CPU1: thread -1, cpu 1, socket 2, mpidr 80000201 <6>[ 0.087648] CPU2: thread -1, cpu 2, socket 2, mpidr 80000202 <6>[ 0.088346] CPU3: thread -1, cpu 3, socket 2, mpidr 80000203 <6>[ 0.088440] smp: Brought up 1 node, 4 CPUs <6>[ 0.108279] SMP: Total of 4 processors activated (8.00 BogoMIPS). <6>[ 0.114606] CPU: All CPU(s) started in SVC mode. <6>[ 0.119992] devtmpfs: initialized <6>[ 0.126463] VFP support v0.3: implementor 41 architecture 2 part 30 variant 5 rev 1 <6>[ 0.131096] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.140967] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.150835] pinctrl core: initialized pinctrl subsystem <6>[ 0.154740] DMI not present or invalid. <6>[ 0.158296] NET: Registered protocol family 16 <6>[ 0.164001] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.171120] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.171238] cpuidle: using governor menu <6>[ 0.179898] No ATAGs? <6>[ 0.182344] hw-breakpoint: found 2 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.190471] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.198364] Serial: AMBA PL011 UART driver <6>[ 0.241936] VCC1V8: supplied by P5V0 <6>[ 0.242291] VCC3V3: supplied by P5V0 <6>[ 0.244238] DDR_VDDC: supplied by P5V0 <6>[ 0.248244] VDD_RTC: supplied by VCC3V3 <6>[ 0.253806] iommu: Default domain type: Translated <6>[ 0.257447] vgaarb: loaded <5>[ 0.260779] SCSI subsystem initialized <6>[ 0.264576] usbcore: registered new interface driver usbfs <6>[ 0.269837] usbcore: registered new interface driver hub <6>[ 0.275332] usbcore: registered new device driver usb <6>[ 0.281623] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.285776] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.295163] PTP clock support registered <6>[ 0.301727] clocksource: Switched to clocksource timer <6>[ 1.224959] NET: Registered protocol family 2 <6>[ 1.225209] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.232580] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 1.240165] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 1.248194] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 1.255600] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 1.262188] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.268920] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.276372] NET: Registered protocol family 1 <6>[ 1.281264] RPC: Registered named UNIX socket transport module. <6>[ 1.286937] RPC: Registered udp transport module. <6>[ 1.291857] RPC: Registered tcp transport module. <6>[ 1.296768] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.303454] PCI: CLS 0 bytes, default 64 <6>[ 1.308009] Trying to unpack rootfs image as initramfs... <6>[ 2.263961] Freeing initrd memory: 15684K <6>[ 2.264810] hw perfevents: enabled with armv7_cortex_a5 PMU driver, 3 counters available <5>[ 2.271998] Initialise system trusted keyrings <6>[ 2.275821] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 2.287655] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 2.288992] NFS: Registering the id_resolver key type <5>[ 2.293717] Key type id_resolver registered <5>[ 2.298018] Key type id_legacy registered <6>[ 2.302370] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 2.309189] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 2.316864] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 2.321903] Key type asymmetric registered <5>[ 2.325728] Asymmetric key parser 'x509' registered <6>[ 2.330878] bounce: pool size: 64 pages <6>[ 2.334958] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 2.342543] io scheduler mq-deadline registered <6>[ 2.347287] io scheduler kyber registered <6>[ 2.358554] gpio-1953 (usb-hub-reset): hogged as output/high <6>[ 2.373500] soc soc0: Amlogic Meson8b (S805) RevA (1b - 0:B72) detected <6>[ 2.424770] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled<6>[ 2.431109] c81004c0.serial: ttyAML0 at MMIO 0xc81004c0 (irq = 34, base_baud = 9960937) is a meson_uart <6>[ 2.440763] printk: console [ttyAML0] enabled <6>[ 2.440763] printk: console [ttyAML0] enabled <6>[ 2.444365] printk: bootconsole [meson0] disabled <6>[ 2.444365] printk: bootconsole [meson0] disabled <6>[ 2.455081] msm_serial: driver initialized <6>[ 2.458712] STMicroelectronics ASC driver initialized <6>[ 2.464800] STM32 USART driver initialized <6>[ 2.481526] brd: module loaded <6>[ 2.488729] loop: module loaded <6>[ 2.497892] CAN device driver interface <6>[ 2.498588] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 2.503104] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 2.507470] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.513715] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 2.519280] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 2.529355] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 2.532837] usbcore: registered new interface driver pegasus <6>[ 2.538686] usbcore: registered new interface driver asix <6>[ 2.544337] usbcore: registered new interface driver ax88179_178a <6>[ 2.550657] usbcore: registered new interface driver cdc_ether <6>[ 2.556764] usbcore: registered new interface driver smsc75xx <6>[ 2.562750] usbcore: registered new interface driver smsc95xx <6>[ 2.568726] usbcore: registered new interface driver net1080 <6>[ 2.574643] usbcore: registered new interface driver cdc_subset <6>[ 2.580789] usbcore: registered new interface driver zaurus <6>[ 2.586666] usbcore: registered new interface driver cdc_ncm <6>[ 2.594562] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 2.599260] ehci-pci: EHCI PCI platform driver <6>[ 2.604003] ehci-platform: EHCI generic platform driver <6>[ 2.609571] ehci-orion: EHCI orion driver <6>[ 2.613806] SPEAr-ehci: EHCI SPEAr driver <6>[ 2.618025] ehci-st: EHCI STMicroelectronics driver <6>[ 2.623166] ehci-exynos: EHCI Exynos driver <6>[ 2.627576] ehci-atmel: EHCI Atmel driver <6>[ 2.631850] tegra-ehci: Tegra EHCI driver <6>[ 2.636106] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 2.642449] ohci-pci: OHCI PCI platform driver <6>[ 2.647148] ohci-platform: OHCI generic platform driver <6>[ 2.652748] SPEAr-ohci: OHCI SPEAr driver <6>[ 2.656931] ohci-st: OHCI STMicroelectronics driver <6>[ 2.662069] ohci-atmel: OHCI Atmel driver <6>[ 2.666773] usbcore: registered new interface driver usb-storage <6>[ 2.676339] i2c /dev entries driver <6>[ 2.684599] meson_wdt c1109900.watchdog: Watchdog enabled (timeout=8 sec, nowayout=0) <6>[ 2.689402] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.693537] sdhci: Copyright(c) Pierre Ossman <6>[ 2.699533] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.705504] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.713267] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 2.717133] usbcore: registered new interface driver usbhid <6>[ 2.722342] usbhid: USB HID core driver <6>[ 2.729983] NET: Registered protocol family 10 <6>[ 2.731978] Segment Routing with IPv6 <6>[ 2.735045] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.741695] NET: Registered protocol family 17 <6>[ 2.745855] can: controller area network core <6>[ 2.750499] NET: Registered protocol family 29 <6>[ 2.755168] can: raw protocol <6>[ 2.758353] can: broadcast manager protocol <6>[ 2.762803] can: netlink gateway - max_hops=1 <5>[ 2.767777] Key type dns_resolver registered <6>[ 2.772014] ThumbEE CPU extension supported. <5>[ 2.776420] Registering SWP/SWPB emulation handler <5>[ 2.781743] Loading compiled-in X.509 certificates <6>[ 2.800285] TFLASH_VDD: supplied by VCC3V3 <6>[ 2.807866] meson8b-dwmac c9410000.ethernet: IRQ eth_wake_irq not found <6>[ 2.809115] meson8b-dwmac c9410000.ethernet: IRQ eth_lpi not found <6>[ 2.816214] stmmaceth c9410000.ethernet: IRQ eth_wake_irq not found <6>[ 2.822084] stmmaceth c9410000.ethernet: IRQ eth_lpi not found <3>[ 2.828162] stmmaceth c9410000.ethernet: dt configuration failed <4>[ 2.836478] dwc2 c90c0000.usb: supply vusb_d not found, using dummy regulator <4>[ 2.841934] dwc2 c90c0000.usb: supply vusb_a not found, using dummy regulator <6>[ 2.912055] dwc2 c90c0000.usb: DWC OTG Controller <6>[ 2.912108] dwc2 c90c0000.usb: new USB bus registered, assigned bus number 1 <6>[ 2.918708] dwc2 c90c0000.usb: irq 35, io mem 0xc90c0000 <6>[ 2.925001] hub 1-0:1.0: USB hub found <6>[ 2.928268] hub 1-0:1.0: 1 port detected <6>[ 2.943059] meson8b-dwmac c9410000.ethernet: IRQ eth_wake_irq not found <6>[ 2.944307] meson8b-dwmac c9410000.ethernet: IRQ eth_lpi not found <6>[ 2.951509] stmmaceth c9410000.ethernet: IRQ eth_wake_irq not found <6>[ 2.951958] platform c1108c20.mmc:slot@1: Got CD GPIO <6>[ 2.957275] stmmaceth c9410000.ethernet: IRQ eth_lpi not found <3>[ 2.968663] stmmaceth c9410000.ethernet: dt configuration failed <6>[ 2.982401] meson8b-dwmac c9410000.ethernet: IRQ eth_wake_irq not found <6>[ 2.983648] meson8b-dwmac c9410000.ethernet: IRQ eth_lpi not found <6>[ 2.990878] stmmaceth c9410000.ethernet: IRQ eth_wake_irq not found <6>[ 2.996629] stmmaceth c9410000.ethernet: IRQ eth_lpi not found <3>[ 3.002725] stmmaceth c9410000.ethernet: dt configuration failed <6>[ 3.016477] meson8b-dwmac c9410000.ethernet: IRQ eth_wake_irq not found <6>[ 3.017725] meson8b-dwmac c9410000.ethernet: IRQ eth_lpi not found <6>[ 3.024889] stmmaceth c9410000.ethernet: IRQ eth_wake_irq not found <6>[ 3.030663] stmmaceth c9410000.ethernet: IRQ eth_lpi not found <3>[ 3.036813] stmmaceth c9410000.ethernet: dt configuration failed <6>[ 3.179114] mmc0: new high speed SDHC card at address aaaa <6>[ 3.179733] mmcblk0: mmc0:aaaa SS16G 14.8 GiB <6>[ 3.196569] mmcblk0: p1 p2 <6>[ 3.204698] meson8b-dwmac c9410000.ethernet: IRQ eth_wake_irq not found <6>[ 3.205947] meson8b-dwmac c9410000.ethernet: IRQ eth_lpi not found <6>[ 3.213043] stmmaceth c9410000.ethernet: IRQ eth_wake_irq not found <6>[ 3.218883] stmmaceth c9410000.ethernet: IRQ eth_lpi not found <3>[ 3.225018] stmmaceth c9410000.ethernet: dt configuration failed <6>[ 3.371695] usb 1-1: new high-speed USB device number 2 using dwc2 <6>[ 3.623771] hub 1-1:1.0: USB hub found <6>[ 3.624113] hub 1-1:1.0: 4 ports detected <6>[ 3.635579] meson8b-dwmac c9410000.ethernet: IRQ eth_wake_irq not found <6>[ 3.636827] meson8b-dwmac c9410000.ethernet: IRQ eth_lpi not found <6>[ 3.644003] stmmaceth c9410000.ethernet: IRQ eth_wake_irq not found <6>[ 3.649764] stmmaceth c9410000.ethernet: IRQ eth_lpi not found <3>[ 3.655902] stmmaceth c9410000.ethernet: dt configuration failed <6>[ 15.534854] Freeing unused kernel memory: 2048K <6>[ 15.535096] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 15.640184] udevd[110]: starting version 3.2.9 <5>[ 15.641040] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 15.646441] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 15.653021] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 15.667147] udevd[110]: specified user 'tss' unknown <27>[ 15.667313] udevd[110]: specified group 'tss' unknown <30>[ 15.674599] udevd[111]: starting eudev-3.2.9 <6>[ 16.326473] VCCK: supplied by P5V0 <6>[ 16.327806] VDDEE: supplied by P5V0 <6>[ 16.330698] meson8b-dwmac c9410000.ethernet: IRQ eth_wake_irq not found <6>[ 16.335182] meson8b-dwmac c9410000.ethernet: IRQ eth_lpi not found <6>[ 16.371260] stmmaceth c9410000.ethernet: IRQ eth_wake_irq not found <6>[ 16.372217] stmmaceth c9410000.ethernet: IRQ eth_lpi not found <3>[ 16.378301] stmmaceth c9410000.ethernet: dt configuration failed <6>[ 16.435887] lima d00c0000.gpu: gp - mali450 version major 0 minor 0 <6>[ 16.436844] lima d00c0000.gpu: pp0 - mali450 version major 0 minor 0 <6>[ 16.443588] lima d00c0000.gpu: pp1 - mali450 version major 0 minor 0 <6>[ 16.450067] lima d00c0000.gpu: l2 cache 8K, 4-way, 64byte cache line, 128bit external bus <6>[ 16.458471] lima d00c0000.gpu: l2 cache 64K, 4-way, 64byte cache line, 128bit external bus <6>[ 16.467624] lima d00c0000.gpu: bus rate = 159375000 <6>[ 16.472099] lima d00c0000.gpu: mod rate = 24000000 <6>[ 16.488980] [drm] Initialized lima 1.1.0 20191231 for d00c0000.gpu on minor 0 <6>[ 16.507561] meson8b-dwmac c9410000.ethernet: IRQ eth_wake_irq not found <6>[ 16.508817] meson8b-dwmac c9410000.ethernet: IRQ eth_lpi not found <6>[ 16.515482] meson8b-dwmac c9410000.ethernet: PTP uses main clock <6>[ 16.522583] meson8b-dwmac c9410000.ethernet: User ID: 0x10, Synopsys ID: 0x37 <6>[ 16.528880] meson8b-dwmac c9410000.ethernet: DWMAC1000 <6>[ 16.534415] meson8b-dwmac c9410000.ethernet: DMA HW capability register supported <6>[ 16.542115] meson8b-dwmac c9410000.ethernet: RX Checksum Offload Engine supported <6>[ 16.549800] meson8b-dwmac c9410000.ethernet: COE Type 2 <6>[ 16.555340] meson8b-dwmac c9410000.ethernet: TX Checksum insertion supported <6>[ 16.562598] meson8b-dwmac c9410000.ethernet: Wake-Up On Lan supported <6>[ 16.569354] meson8b-dwmac c9410000.ethernet: Normal descriptors <6>[ 16.575455] meson8b-dwmac c9410000.ethernet: Ring mode enabled <6>[ 16.581497] meson8b-dwmac c9410000.ethernet: Enable RX Mitigation via HW Watchdog Timer done Saving random seed: <5>[ 16.825032] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: OK Starting dropbear sshd: <5>[ 16.953152] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-3158655/environment . /lava-3158655/environment / # /lava-3158655/bin/lava-test-runner /lava-3158655/0 /lava-3158655/bin/lava-test-runner /lava-3158655/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-3158655/0/tests/0_dmesg + cat uuid + UUID=3158655_1.5.2.4.1 + set +x <8>[ 17.593396] + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 17.653151] <8>[ 17.696892] <8>[ 17.742782] + set +x <8>[ 17.746955] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-3158655/environment / # . /lava-3158655/environment/lava-3158655/bin/lava-test-runner /lava-3158655/1 / # /lava-3158655/bin/lava-test-runner /lava-3158655/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-3158655/1/tests/1_bootrr + cat uuid + UUID=3158655_1.5.2.4.5 + set +x <8>[ 18.282655] + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-3158655/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto /lava-3158655/1/../bin/lava-test-case <8>[ 18.356040] /lava-3158655/1/../bin/lava-test-case <8>[ 18.405636] /lava-3158655/1/../bin/lava-test-case <8>[ 18.429221] + set +x <8>[ 18.445206] / #