Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. ser2net port 3009 device /dev/ttyimx7d-sdb-2 [115200 N81] (Debian GNU/Linux) U-Boot 2016.03-imx_v2016.03_4.1.15_2.0.0_ga+g0ec2a01 (Nov 11 2016 - 03:13:54 -0600) CPU: Freescale i.MX7D rev1.3 996 MHz (running at 792 MHz) CPU: Commercial temperature grade (0C to 95C) at 27C Reset cause: POR Board: i.MX7D SABRESD RevA I2C: ready DRAM: 1 GiB PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11 MMC: FSL_SDHC: 0, FSL_SDHC: 1 *** Warning - bad CRC, using default environment Display: TFT43AB (480x272) Video: 480x272x24 In: serial Out: serial Err: serial switch to partitions #0, OK mmc0 is current device Net: FEC0 Normal Boot Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.1.166 (1341 ms) => setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 => tftp 0x80800000 1144379/tftp-deploy-4xfdo7wy/kernel/zImage tftp 0x80800000 1144379/tftp-deploy-4xfdo7wy/kernel/zImage Using FEC0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.166; sending through gateway 172.16.1.4 Filename '1144379/tftp-deploy-4xfdo7wy/kernel/zImage'. Load address: 0x80800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 10.4 MiB/s done Bytes transferred = 9687552 (93d200 hex) => tftp 0x86800000 1144379/tftp-deploy-4xfdo7wy/ramdisk/ramdisk.cpio.gz.uboot tftp 0x86800000 1144379/tftp-deploy-4xfdo7wy/ramdisk/ramdisk.cpio.gz.uboot Using FEC0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.166; sending through gateway 172.16.1.4 Filename '1144379/tftp-deploy-4xfdo7wy/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x86800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####################################################### 10.4 MiB/s done Bytes transferred = 16068351 (f52eff hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x83000000 1144379/tftp-deploy-4xfdo7wy/dtb/imx7d-sdb.dtb tftp 0x83000000 1144379/tftp-deploy-4xfdo7wy/dtb/imx7d-sdb.dtb Using FEC0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.166; sending through gateway 172.16.1.4 Filename '1144379/tftp-deploy-4xfdo7wy/dtb/imx7d-sdb.dtb'. Load address: 0x83000000 Loading: *### 5.2 MiB/s done Bytes transferred = 37996 (946c hex) => setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x80800000 0x86800000 0x83000000 bootz 0x80800000 0x86800000 0x83000000 Kernel image @ 0x80800000 [ 0x000000 - 0x93d200 ] ## Loading init Ramdisk from Legacy Image at 86800000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16068287 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Using Device Tree in place at 83000000, end 8300c46b Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.165-cip24 (KernelCI@build-j903990-arm-gcc-10-multi-v7-defconfig-vwnz5) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Tue Jan 24 12:12:38 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX7 SabreSD Board [ 0.000000] earlycon: ec_imx6q0 at MMIO 0x30860000 (options '') [ 0.000000] printk: bootconsole [ec_imx6q0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0xbc000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000afffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x00000000b0000000-0x00000000bfffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000bfffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000000bfffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 933880K/1048576K available (13312K kernel code, 2232K rwdata, 5344K rodata, 2048K init, 427K bss, 49160K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] arch_timer: cp15 timer(s) running at 8.00MHz (virt). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 440795202120 ns <6>[ 0.000007] sched_clock: 56 bits at 8MHz, resolution 125ns, wraps every 2199023255500ns <6>[ 0.008312] Switching to timer-based delay loop, resolution 125ns <6>[ 0.015989] Switching to timer-based delay loop, resolution 41ns <6>[ 0.021004] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.029140] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.043552] Console: colour dummy device 80x30 <6>[ 0.045463] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) <6>[ 0.056109] pid_max: default: 32768 minimum: 301 <6>[ 0.061169] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.068626] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.077416] CPU: Testing write buffer coherency: ok <6>[ 0.082145] CPU0: update cpu_capacity 1024 <6>[ 0.086191] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.092897] Setting up static identity map for 0x80300000 - 0x803000ac <6>[ 0.100438] rcu: Hierarchical SRCU implementation. <6>[ 0.107556] EFI services will not be available. <6>[ 0.109738] smp: Bringing up secondary CPUs ... <6>[ 0.115015] smp: Brought up 1 node, 1 CPU <6>[ 0.118609] SMP: Total of 1 processors activated (48.00 BogoMIPS). <6>[ 0.125125] CPU: All CPU(s) started in SVC mode. <6>[ 0.130535] devtmpfs: initialized <6>[ 0.141696] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 <6>[ 0.147106] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.157011] futex hash table entries: 512 (order: 3, 32768 bytes, linear) <6>[ 0.166474] pinctrl core: initialized pinctrl subsystem <6>[ 0.171482] DMI not present or invalid. <6>[ 0.174789] NET: Registered protocol family 16 <6>[ 0.180546] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.188246] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.188367] cpuidle: using governor menu <6>[ 0.196586] No ATAGs? <6>[ 0.198694] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.206969] hw-breakpoint: maximum watchpoint size is 8 bytes. <6>[ 0.215971] Serial: AMBA PL011 UART driver <6>[ 0.266221] imx7d-pinctrl 302c0000.iomuxc-lpsr: initialized IMX pinctrl driver <6>[ 0.271992] imx7d-pinctrl 30330000.pinctrl: initialized IMX pinctrl driver <6>[ 0.324542] iommu: Default domain type: Translated <6>[ 0.327802] vgaarb: loaded <5>[ 0.330818] SCSI subsystem initialized <6>[ 0.334571] usbcore: registered new interface driver usbfs <6>[ 0.339673] usbcore: registered new interface driver hub <6>[ 0.345324] usbcore: registered new device driver usb <6>[ 0.358697] i2c i2c-0: IMX I2C adapter registered <6>[ 0.366700] i2c i2c-1: IMX I2C adapter registered <6>[ 0.369397] i2c i2c-2: IMX I2C adapter registered <6>[ 0.379598] i2c i2c-3: IMX I2C adapter registered <6>[ 0.383077] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.387004] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.396451] PTP clock support registered <6>[ 0.404313] clocksource: Switched to clocksource arch_sys_counter <6>[ 1.512428] NET: Registered protocol family 2 <6>[ 1.514571] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.523159] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 1.530636] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 1.538722] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 1.546217] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 1.552828] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.559696] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.567186] NET: Registered protocol family 1 <6>[ 1.572409] RPC: Registered named UNIX socket transport module. <6>[ 1.577880] RPC: Registered udp transport module. <6>[ 1.582811] RPC: Registered tcp transport module. <6>[ 1.587816] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.594562] PCI: CLS 0 bytes, default 64 <6>[ 1.599273] Trying to unpack rootfs image as initramfs... <6>[ 2.919678] Freeing initrd memory: 15692K <6>[ 2.921917] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available <5>[ 2.931268] Initialise system trusted keyrings <6>[ 2.934870] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 2.948036] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 2.952171] NFS: Registering the id_resolver key type <5>[ 2.956729] Key type id_resolver registered <5>[ 2.961103] Key type id_legacy registered <6>[ 2.965519] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 2.972392] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 2.980147] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 2.985271] Key type asymmetric registered <5>[ 2.989104] Asymmetric key parser 'x509' registered <6>[ 2.994349] bounce: pool size: 64 pages <6>[ 2.998415] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 3.006099] io scheduler mq-deadline registered <6>[ 3.010891] io scheduler kyber registered <4>[ 3.038499] pwm-backlight backlight: supply power not found, using dummy regulator <6>[ 3.056142] mxs-dma 33000000.dma-apbh: initialized <4>[ 3.070967] imx-sdma 30bd0000.sdma: Direct firmware load for imx/sdma/sdma-imx7d.bin failed with error -2 <6>[ 3.078055] imx-sdma 30bd0000.sdma: external firmware not found, using ROM firmware <6>[ 3.140365] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.148771] SuperH (H)SCI(F) driver initialized <3>[ 3.151544] clk: failed to reparent uart1_src to pll_sys_main_240m_clk: -16 <6>[ 3.158312] 30860000.serial: ttymxc0 at MMIO 0x30860000 (irq = 58, base_baud = 1500000) is a IMX <6>[ 3.167176] printk: console [ttymxc0] enabled <6>[ 3.167176] printk: console [ttymxc0] enabled <6>[ 3.176322] printk: bootconsole [ec_imx6q0] disabled <6>[ 3.176322] printk: bootconsole [ec_imx6q0] disabled <6>[ 3.187793] 30a80000.serial: ttymxc5 at MMIO 0x30a80000 (irq = 67, base_baud = 15000000) is a IMX <6>[ 3.200193] msm_serial: driver initialized <6>[ 3.204820] STMicroelectronics ASC driver initialized <6>[ 3.211807] STM32 USART driver initialized <6>[ 3.236112] brd: module loaded <6>[ 3.247210] loop: module loaded <6>[ 3.265701] CAN device driver interface <6>[ 3.271010] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.282236] pps pps0: new PPS source ptp0 <3>[ 3.287454] fec 30bf0000.ethernet: Invalid MAC address: 00:00:00:00:00:00 <6>[ 3.294599] fec 30bf0000.ethernet: Using random MAC address: 2a:c9:37:cf:7e:95 <6>[ 4.344074] fec 30bf0000.ethernet eth0: registered PHC device 0 <6>[ 4.351774] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 4.357054] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 4.363331] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 4.369015] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 4.380285] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 4.388035] usbcore: registered new interface driver pegasus <6>[ 4.394005] usbcore: registered new interface driver asix <6>[ 4.399724] usbcore: registered new interface driver ax88179_178a <6>[ 4.406135] usbcore: registered new interface driver cdc_ether <6>[ 4.412286] usbcore: registered new interface driver smsc75xx <6>[ 4.418365] usbcore: registered new interface driver smsc95xx <6>[ 4.424431] usbcore: registered new interface driver net1080 <6>[ 4.430389] usbcore: registered new interface driver cdc_subset <6>[ 4.436625] usbcore: registered new interface driver zaurus <6>[ 4.442563] usbcore: registered new interface driver cdc_ncm <6>[ 4.451697] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 4.458523] ehci-pci: EHCI PCI platform driver <6>[ 4.463274] ehci-platform: EHCI generic platform driver <6>[ 4.469038] ehci-orion: EHCI orion driver <6>[ 4.473495] SPEAr-ehci: EHCI SPEAr driver <6>[ 4.477951] ehci-st: EHCI STMicroelectronics driver <6>[ 4.483243] ehci-exynos: EHCI Exynos driver <6>[ 4.487872] ehci-atmel: EHCI Atmel driver <6>[ 4.492300] tegra-ehci: Tegra EHCI driver <6>[ 4.496778] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.503266] ohci-pci: OHCI PCI platform driver <6>[ 4.508041] ohci-platform: OHCI generic platform driver <6>[ 4.513762] SPEAr-ohci: OHCI SPEAr driver <6>[ 4.518212] ohci-st: OHCI STMicroelectronics driver <6>[ 4.523504] ohci-atmel: OHCI Atmel driver <6>[ 4.528803] usbcore: registered new interface driver usb-storage <6>[ 4.542322] i2c /dev entries driver <3>[ 4.563481] CPUidle arm: CPU 0 failed to init idle CPU ops <6>[ 4.569890] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.576379] sdhci: Copyright(c) Pierre Ossman <6>[ 4.583395] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.591390] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.602276] sdhci-esdhc-imx 30b40000.mmc: Got CD GPIO <6>[ 4.607685] sdhci-esdhc-imx 30b40000.mmc: Got WP GPIO <6>[ 4.618075] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.625575] usbcore: registered new interface driver usbhid <6>[ 4.631418] usbhid: USB HID core driver <6>[ 4.641686] NET: Registered protocol family 10 <6>[ 4.647690] Segment Routing with IPv6 <6>[ 4.651700] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.658597] NET: Registered protocol family 17 <6>[ 4.663319] can: controller area network core <6>[ 4.668039] NET: Registered protocol family 29 <6>[ 4.672749] can: raw protocol <6>[ 4.676014] can: broadcast manager protocol <6>[ 4.680470] can: netlink gateway - max_hops=1 <5>[ 4.685641] Key type dns_resolver registered <6>[ 4.690293] ThumbEE CPU extension supported. <5>[ 4.694873] Registering SWP/SWPB emulation handler <5>[ 4.700368] Loading compiled-in X.509 certificates <6>[ 4.740958] mmc2: SDHCI controller on 30b60000.mmc [30b60000.mmc] using ADMA <4>[ 4.752075] pwm-backlight backlight: supply power not found, using dummy regulator <6>[ 4.760629] mmc0: SDHCI controller on 30b40000.mmc [30b40000.mmc] using ADMA <4>[ 4.783308] imx_usb 30b10000.usb: No over current polarity defined <4>[ 4.792310] imx_usb 30b20000.usb: No over current polarity defined <4>[ 4.804161] pwm-backlight backlight: supply power not found, using dummy regulator <4>[ 4.827126] imx_usb 30b10000.usb: No over current polarity defined <4>[ 4.836121] imx_usb 30b20000.usb: No over current polarity defined <4>[ 4.847998] pwm-backlight backlight: supply power not found, using dummy regulator <6>[ 4.859046] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.881003] imx_usb 30b10000.usb: No over current polarity defined <4>[ 4.890018] imx_usb 30b20000.usb: No over current polarity defined <4>[ 4.901888] pwm-backlight backlight: supply power not found, using dummy regulator <6>[ 4.910237] mmc1: SDHCI controller on 30b50000.mmc [30b50000.mmc] using ADMA <4>[ 4.932383] imx_usb 30b10000.usb: No over current polarity defined <4>[ 4.941374] imx_usb 30b20000.usb: No over current polarity defined <4>[ 4.953220] pwm-backlight backlight: supply power not found, using dummy regulator <3>[ 4.968272] fec 30bf0000.ethernet eth0: Unable to connect to phy <3>[ 4.978017] IP-Config: Failed to open eth0 <3>[ 4.982387] IP-Config: No network devices available <6>[ 5.007016] Freeing unused kernel memory: 2048K <6>[ 5.012275] Run /init as init process <6>[ 5.020849] mmc0: new high speed SDHC card at address aaaa <6>[ 5.029577] mmcblk0: mmc0:aaaa SA16G 14.8 GiB <4>[ 5.039165] mmc1: queuing unknown CIS tuple 0x80 (2 bytes) <6>[ 5.052477] mmcblk0: p1 p2 <4>[ 5.059339] mmc1: queuing unknown CIS tuple 0x80 (7 bytes) <4>[ 5.083751] mmc1: queuing unknown CIS tuple 0x80 (6 bytes) <4>[ 5.094834] imx_usb 30b10000.usb: No over current polarity defined <4>[ 5.103802] imx_usb 30b20000.usb: No over current polarity defined <4>[ 5.115822] pwm-backlight backlight: supply power not found, using dummy regulator Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 5.300780] udevd[128]: starting version 3.2.9 <5>[ 5.312003] random: udevd: uninitialized urandom read (16 bytes read) <6>[ 5.322567] mmc1: new ultra high speed SDR104 SDIO card at address 0001 <5>[ 5.330404] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 5.337635] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 5.353995] udevd[128]: specified user 'tss' unknown <27>[ 5.359924] udevd[128]: specified group 'tss' unknown <30>[ 5.376288] udevd[129]: starting eudev-3.2.9 <5>[ 5.506237] cfg80211: Loading compiled-in X.509 certificates for regulatory database <5>[ 6.053467] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' <4>[ 6.060595] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 <6>[ 6.069517] cfg80211: failed to load regulatory.db <6>[ 6.189717] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4339-sdio for chip BCM4339/2 <4>[ 6.198921] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac4339-sdio.bin failed with error -2 <4>[ 6.236267] imx_usb 30b10000.usb: No over current polarity defined <4>[ 6.245318] imx_usb 30b20000.usb: No over current polarity defined <4>[ 6.257250] pwm-backlight backlight: supply power not found, using dummy regulator <3>[ 7.274413] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000): clkctl 0x50 <6>[ 7.391794] gpio-expander@0 enforce active low on chipselect handle <4>[ 7.454778] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 7.462978] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 7.471627] usb_phy_generic usbphynop3: deferred probe timeout, ignoring dependency <4>[ 7.479604] usb_phy_generic: probe of usbphynop3 failed with error -110 <4>[ 7.486747] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 7.494851] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <4>[ 7.506059] imx_usb 30b10000.usb: No over current polarity defined <4>[ 7.727650] imx_usb 30b20000.usb: No over current polarity defined <6>[ 7.804386] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 7.809588] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 7.954350] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 8.015257] hub 1-0:1.0: USB hub found <6>[ 8.024592] hub 1-0:1.0: 1 port detected <4>[ 8.130563] pwm-backlight backlight: supply power not found, using dummy regulator <6>[ 8.803456] caam 30900000.crypto: Entropy delay = 3200 <6>[ 8.868408] caam 30900000.crypto: Instantiated RNG4 SH0 <6>[ 8.927819] caam 30900000.crypto: Instantiated RNG4 SH1 <6>[ 8.933319] caam 30900000.crypto: device ID = 0x0a16030000000000 (Era 8) <6>[ 8.940301] caam 30900000.crypto: job rings = 3, qi = 0 <4>[ 8.959196] pwm-backlight backlight: supply power not found, using dummy regulator <4>[ 9.260389] pwm-backlight backlight: supply power not found, using dummy regulator <4>[ 9.653222] pwm-backlight backlight: supply power not found, using dummy regulator <6>[ 10.901779] caam algorithms registered in /proc/crypto <6>[ 10.909069] caam 30900000.crypto: caam pkc algorithms registered in /proc/crypto <6>[ 10.916810] caam 30900000.crypto: registering rng-caam <4>[ 10.934076] pwm-backlight backlight: supply power not found, using dummy regulator <4>[ 10.984183] pwm-backlight backlight: supply power not found, using dummy regulator done Saving random seed: <5>[ 11.031179] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: ip: RTNETLINK answers: File exists FAIL <5>[ 11.100661] random: crng init done Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1144379/environment . /lava-1144379/environment / # /lava-1144379/bin/lava-test-runner /lava-1144379/0 /lava-1144379/bin/lava-test-runner /lava-1144379/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1144379/0/tests/0_dmesg + cat uuid + UUID=1144379_1.5.2.4<8>[ 16.954677] .1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 17.002774] <8>[ 17.046692] <8>[ 17.090372] + set<8>[ 17.100678] +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-1144379/environment / # . /lava-1144379/environment/lava-1144379/bin/lava-test-runner /lava-1144379/1 / # /lava-1144379/bin/lava-test-runner /lava-1144379/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1144379/1/tests/1_bootrr +<8>[ 22.833568] cat uuid + UUID=1144379_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-1144379/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto 30730000.lcdif 30360000.anatop:tempmon imx_thermal: failed to register cpufreq cooling device regulator-lcd-3v3 backlight imx-pgc-domain.0 imx-pgc: Failed to get domain's regulator imx-pgc-domain.1 imx-pgc: Failed to get domain's regulator imx-pgc-domain.2 imx-pgc: Failed to get domain's regulator panel 30be0000.ethernet /lava-1144379/1/../bin/lava-test-case <8>[ 23.890476] /lava-1144379/1/../bin/lava-test-case <8>[ 24.934030] /lava-1144379/1/../bin/lava-test-case <8>[ 24.958996] + set +x <8>[ 24.978264] / #