Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. NOTICE: UDIMM 18ASF1G72AZ-2G1A1 NOTICE: 16 GB DDR4, 64-bit, CL=13, ECC on, 256B, CS0+CS1 NOTICE: UDIMM 18ASF1G72AZ-2G1A1 NOTICE: 4 GB DDR4, 32-bit, CL=11, ECC on, CS0+CS1 NOTICE: BL2: v1.5(release):LSDK-19.06 NOTICE: BL2: Built : 21:37:56, Jul 29 2019 NOTICE: BL2: Booting BL31NOTICE: BL31: v1.5(release):LSDK-19.06 NOTICE: BL31: Built : 21:38:04, Jul 29 2019 NOTICE: Welcome to LS2088 BL31 Phase U-Boot 2019.04-gcbd7e30bf8 (Jul 29 2019 - 21:37:23 +0800) SoC: LS2088AE Rev1.0 (0x87090010) Clock Configuration: CPU0(A72):1800 MHz CPU1(A72):1800 MHz CPU2(A72):1800 MHz CPU3(A72):1800 MHz CPU4(A72):1800 MHz CPU5(A72):1800 MHz CPU6(A72):1800 MHz CPU7(A72):1800 MHz Bus: 700 MHz DDR: 1866.667 MT/s DP-DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 483038b8 48480048 00000000 00000000 00000010: 00000000 00000000 00a00000 00000000 00000020: 01e01180 00002581 00000000 00000000 00000030: 00400c0b 00000000 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000000 00000000 00027000 00000000 00000070: 412a0000 00040000 Model: Freescale Layerscape 2080a RDB Board Board: LS2088AE Rev1.0-RDB, Board Arch: V1, Board version: D, boot from vBank: 4 FPGA: v1.18 SERDES1 Reference : Clock1 = 156.25MHz Clock2 = 156.25MHz SERDES2 Reference : Clock1 = 100MHz Clock2 = 100MHz I2C: ready DRAM: 15.9 GiB DDR 15.9 GiB (DDR4, 64-bit, CL=13, ECC on) DDR Controller Interleaving Mode: 256B DDR Chip-Select Interleaving Mode: CS0+CS1 SEC0: RNG instantiated SEC0: RNG instantiated Using SERDES1 Protocol: 42 (0x2a) Using SERDES2 Protocol: 65 (0x41) Flash: 128 MiB NAND: 2048 MiB MMC: FSL_SDHC: 0 Loading Environment from Flash... OK EEPROM: Invalid ID (ff ff ff ff) In: serial Out: serial Err: serial VID: Core voltage after adjustment is at 1054 mV Net: DPMAC5@xgmii running firmware version 2.3.5 DPMAC5@xgmii: system interface XFI DPMAC5@xgmii: Aquantia AQR405 Firmware Version 2.3.5 DPMAC6@xgmii running firmware version 2.3.5 DPMAC6@xgmii: system interface XFI DPMAC6@xgmii: Aquantia AQR405 Firmware Version 2.3.5 DPMAC7@xgmii running firmware version 2.3.5 DPMAC7@xgmii: system interface XFI DPMAC7@xgmii: Aquantia AQR405 Firmware Version 2.3.5 DPMAC8@xgmii running firmware version 2.3.5 DPMAC8@xgmii: system interface XFI DPMAC8@xgmii: Aquantia AQR405 Firmware Version 2.3.5 PCIe0: pcie@3400000 disabled PCIe1: pcie@3500000 disabled PCIe2: pcie@3600000 Root Complex: x1 gen1 PCIe3: pcie@3700000 Root Complex: no link e1000: 68:05:ca:36:8d:e8 DPMAC1@xgmii Warning: DPMAC1@xgmii (eth0) using random MAC address - 26:fe:94:50:e5:84 , DPMAC2@xgmii Warning: DPMAC2@xgmii (eth1) using random MAC address - 7e:03:c1:4c:5e:15 , DPMAC3@xgmii Warning: DPMAC3@xgmii (eth2) using random MAC address - 76:0b:e8:36:d2:19 , DPMAC4@xgmii Warning: DPMAC4@xgmii (eth3) using random MAC address - 4e:50:15:96:3b:11 , DPMAC5@xgmii Warning: DPMAC5@xgmii (eth4) using random MAC address - 46:58:3c:ec:b7:1d , DPMAC6@xgmii Warning: DPMAC6@xgmii (eth5) using random MAC address - 62:42:e4:26:80:d1 , DPMAC7@xgmii Warning: DPMAC7@xgmii (eth6) using random MAC address - 6a:4a:cd:5c:0c:dd , DPMAC8@xgmii Warning: DPMAC8@xgmii (eth7) using random MAC address - 32:12:77:b5:2e:26 , e1000#0 [PRIME] crc32+ fsl-mc: Booting Management Complex ... SUCCESS fsl-mc: Management Complex booted (version: 10.16.2, boot status: 0x1) Hit any key to stop autoboot: 10  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => setenv ipaddr 172.16.1.11; setenv serverip 172.16.1.4; setenv ethact e1000#0; setenv ethprime e1000#0 setenv ipaddr 172.16.1.11; setenv serverip 172.16.1.4; setenv ethact e1000#0; setenv ethprime e1000#0 => setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 => tftp 0x80080000 1144382/tftp-deploy-gb3v0omg/kernel/uImage tftp 0x80080000 1144382/tftp-deploy-gb3v0omg/kernel/uImage Using e1000#0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.11 Filename '1144382/tftp-deploy-gb3v0omg/kernel/uImage'. Load address: 0x80080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ##################################################### 4.4 MiB/s done Bytes transferred = 43711040 (29afa40 hex) => tftp 0x91000000 1144382/tftp-deploy-gb3v0omg/ramdisk/ramdisk.cpio.gz.uboot tftp 0x91000000 1144382/tftp-deploy-gb3v0omg/ramdisk/ramdisk.cpio.gz.uboot Using e1000#0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.11 Filename '1144382/tftp-deploy-gb3v0omg/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x91000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########################################## 1.7 MiB/s done Bytes transferred = 21605788 (149ad9c hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 1144382/tftp-deploy-gb3v0omg/dtb/fsl-ls2088a-rdb.dtb tftp 0x90000000 1144382/tftp-deploy-gb3v0omg/dtb/fsl-ls2088a-rdb.dtb Using e1000#0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.11 Filename '1144382/tftp-deploy-gb3v0omg/dtb/fsl-ls2088a-rdb.dtb'. Load address: 0x90000000 Loading: *## 2.9 KiB/s done Bytes transferred = 19637 (4cb5 hex) => setenv bootargs 'console=ttyS1,115200n8 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0600 nousb default_hugepagesz=2m hugepagesz=2m hugepages=256 arm-smmu-mod.disable_bypass=n arm-smmu.disable_bypass=n ip=dhcp' setenv bootargs 'console=ttyS1,115200n8 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0600 nousb default_hugepagesz=2m hugepagesz=2m hugepages=256 arm-smmu-mod.disable_bypass=n arm-smmu.disable_bypass=n ip=dhcp' => bootm 0x80080000 0x91000000 0x90000000 bootm 0x80080000 0x91000000 0x90000000 ## Booting kernel from Legacy Image at 80080000 ... Image Name: Created: 2023-07-12 6:53:43 UTC Image Type: AArch64 Linux Kernel Image (uncompressed) Data Size: 43710976 Bytes = 41.7 MiB Load Address: 80080000 Entry Point: 80080000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 91000000 ... Image Name: Created: 2023-07-12 6:53:48 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 21605724 Bytes = 20.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Loading Kernel Image ... OK Using Device Tree in place at 0000000090000000, end 0000000090007cb4 fsl-mc: DPL not deployed, DPAA2 ethernet not work Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd082] [ 0.000000] Linux version 5.10.165-cip24 (KernelCI@build-j904077-arm64-gcc-10-defconfig-kselftest-8r6ck) (aarch64-linux-gnu-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP PREEMPT Tue Jan 24 12:18:06 UTC 2023 [ 0.000000] Machine model: Freescale Layerscape 2088A RDB Board [ 0.000000] earlycon: uart8250 at MMIO 0x00000000021c0600 (options '') [ 0.000000] printk: bootconsole [uart8250] enabled [ 0.000000] efi: UEFI not found. [ 0.000000] [Firmware Bug]: Kernel image misaligned at boot, please fix your bootloader! [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x000000837fffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x837e3f77c0-0x837e3f9fff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x000000837fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fbdfffff] [ 0.000000] node 0: [mem 0x0000008080000000-0x000000837fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000837fffffff] [ 0.000000] cma: Reserved 32 MiB at 0x00000000f9c00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 34 pages/cpu s100944 r8192 d30128 u139264 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: EL2 vector hardening [ 0.000000] CPU features: kernel page table isolation forced ON by KASLR [ 0.000000] CPU features: detected: Kernel page table isolation (KPTI) [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: detected: ARM erratum 1742098 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 3595776 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttyS1,115200n8 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0600 nousb default_hugepagesz=2m hugepagesz=2m hugepages=256 arm-smmu-mod.disable_bypass=n arm-smmu.disable_bypass=n ip=dhcp [ 0.000000] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes, linear) [ 0.000000] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] software IO TLB: mapped [mem 0x00000000f5c00000-0x00000000f9c00000] (64MB) [ 0.000000] Memory: 14154880K/14612480K available (18816K kernel code, 4542K rwdata, 9456K rodata, 9728K init, 11274K bss, 424832K reserved, 32768K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 [ 0.000000] ftrace: allocating 58545 entries in 229 pages [ 0.000000] ftrace: allocated 229 pages with 5 groups [ 0.000000] Running RCU self tests [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU lockdep checking is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=8. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 256 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] GICv3: Distributor has no Range Selector support [ 0.000000] GICv3: 16 PPIs implemented [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006100000 [ 0.000000] ITS [mem 0x06020000-0x0603ffff] [ 0.000000] ITS@0x0000000006020000: allocated 8192 Devices @8080200000 (flat, esz 8, psz 64K, shr 0) [ 0.000000] ITS: using cache flushing for cmd queue [ 0.000000] GICv3: using LPI property table @0x0000008080210000 [ 0.000000] GIC: using cache flushing for LPI property table [ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000008080220000 [ 0.000000] arch_timer: Enabling global workaround for Freescale erratum a005858 [ 0.000000] arch_timer: CPU0: Trapping CNTVCT access [ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c409fb33, max_idle_ns: 440795203156 ns [ 0.000002] sched_clock: 56 bits at 25MHz, resolution 39ns, wraps every 4398046511103ns [ 0.008386] Console: colour dummy device 80x25 [ 0.012877] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.020680] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.024807] ... MAX_LOCK_DEPTH: 48 [ 0.029021] ... MAX_LOCKDEP_KEYS: 8192 [ 0.033409] ... CLASSHASH_SIZE: 4096 [ 0.037796] ... MAX_LOCKDEP_ENTRIES: 32768 [ 0.042270] ... MAX_LOCKDEP_CHAINS: 65536 [ 0.046746] ... CHAINHASH_SIZE: 32768 [ 0.051223] memory used by lock dependency info: 6365 kB [ 0.056660] memory used for stack traces: 4224 kB [ 0.061488] per task-struct memory footprint: 1920 bytes [ 0.066995] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) [ 0.077428] pid_max: default: 32768 minimum: 301 [ 0.082202] LSM: Security Framework initializing [ 0.086885] LSM support for eBPF active [ 0.090825] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.098494] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.109775] rcu: Hierarchical SRCU implementation. [ 0.117000] Platform MSI: gic-its@6020000 domain created [ 0.122534] PCI/MSI: /interrupt-controller@6000000/gic-its@6020000 domain created [ 0.130168] fsl-mc MSI: gic-its@6020000 domain created [ 0.135830] EFI services will not be available. [ 0.141243] smp: Bringing up secondary CPUs ... [ 0.147018] Detected PIPT I-cache on CPU1 [ 0.147035] GICv3: CPU1: found redistributor 1 region 0:0x0000000006120000 [ 0.147044] GICv3: CPU1: using allocated LPI pending table @0x0000008080230000 [ 0.147070] arch_timer: CPU1: Trapping CNTVCT access [ 0.147085] CPU1: Booted secondary processor 0x0000000001 [0x410fd082] [ 0.148500] Detected PIPT I-cache on CPU2 [ 0.148517] GICv3: CPU2: found redistributor 100 region 0:0x0000000006140000 [ 0.148526] GICv3: CPU2: using allocated LPI pending table @0x0000008080240000 [ 0.148548] arch_timer: CPU2: Trapping CNTVCT access [ 0.148562] CPU2: Booted secondary processor 0x0000000100 [0x410fd082] [ 0.149913] Detected PIPT I-cache on CPU3 [ 0.149924] GICv3: CPU3: found redistributor 101 region 0:0x0000000006160000 [ 0.149933] GICv3: CPU3: using allocated LPI pending table @0x0000008080250000 [ 0.149948] arch_timer: CPU3: Trapping CNTVCT access [ 0.149959] CPU3: Booted secondary processor 0x0000000101 [0x410fd082] [ 0.151275] Detected PIPT I-cache on CPU4 [ 0.151294] GICv3: CPU4: found redistributor 200 region 0:0x0000000006180000 [ 0.151302] GICv3: CPU4: using allocated LPI pending table @0x0000008080260000 [ 0.151325] arch_timer: CPU4: Trapping CNTVCT access [ 0.151339] CPU4: Booted secondary processor 0x0000000200 [0x410fd082] [ 0.152643] Detected PIPT I-cache on CPU5 [ 0.152655] GICv3: CPU5: found redistributor 201 region 0:0x00000000061a0000 [ 0.152663] GICv3: CPU5: using allocated LPI pending table @0x0000008080270000 [ 0.152679] arch_timer: CPU5: Trapping CNTVCT access [ 0.152690] CPU5: Booted secondary processor 0x0000000201 [0x410fd082] [ 0.154011] Detected PIPT I-cache on CPU6 [ 0.154030] GICv3: CPU6: found redistributor 300 region 0:0x00000000061c0000 [ 0.154040] GICv3: CPU6: using allocated LPI pending table @0x0000008080280000 [ 0.154062] arch_timer: CPU6: Trapping CNTVCT access [ 0.154077] CPU6: Booted secondary processor 0x0000000300 [0x410fd082] [ 0.155398] Detected PIPT I-cache on CPU7 [ 0.155410] GICv3: CPU7: found redistributor 301 region 0:0x00000000061e0000 [ 0.155419] GICv3: CPU7: using allocated LPI pending table @0x0000008080290000 [ 0.155434] arch_timer: CPU7: Trapping CNTVCT access [ 0.155446] CPU7: Booted secondary processor 0x0000000301 [0x410fd082] [ 0.155746] smp: Brought up 1 node, 8 CPUs [ 0.369744] SMP: Total of 8 processors activated. [ 0.374511] CPU features: detected: 32-bit EL0 Support [ 0.379736] CPU features: detected: CRC32 instructions [ 0.384928] CPU features: detected: 32-bit EL1 Support [ 0.417219] CPU: All CPU(s) started at EL2 [ 0.421440] alternatives: patching kernel code [ 0.427954] devtmpfs: initialized [ 0.443718] KASLR enabled [ 0.447401] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.457237] futex hash table entries: 2048 (order: 6, 262144 bytes, linear) [ 0.465256] pinctrl core: initialized pinctrl subsystem [ 0.472862] DMI not present or invalid. [ 0.477574] NET: Registered protocol family 16 [ 0.484591] DMA: preallocated 2048 KiB GFP_KERNEL pool for atomic allocations [ 0.492139] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.501315] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.509487] audit: initializing netlink subsys (disabled) [ 0.515200] audit: type=2000 audit(0.352:1): state=initialized audit_enabled=0 res=1 [ 0.516928] thermal_sys: Registered thermal governor 'step_wise' [ 0.523023] thermal_sys: Registered thermal governor 'power_allocator' [ 0.531081] cpuidle: using governor menu [ 0.541894] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.549034] ASID allocator initialised with 32768 entries [ 0.556604] Serial: AMBA PL011 UART driver [ 0.605307] Machine: Freescale Layerscape 2088A RDB Board [ 0.610766] SoC family: QorIQ LS2088A [ 0.614450] SoC ID: svr:0x87090010, Revision: 1.0 [ 0.661598] HugeTLB registered 2.00 MiB page size, pre-allocated 256 pages [ 0.668616] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 0.675377] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages [ 0.682137] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages [ 0.691668] cryptd: max_cpu_qlen set to 1000 [ 0.700858] ACPI: Interpreter disabled. [ 0.708201] iommu: Default domain type: Translated [ 0.713585] vgaarb: loaded [ 0.717068] SCSI subsystem initialized [ 0.721634] usbcore: registered new interface driver usbfs [ 0.727275] usbcore: registered new interface driver hub [ 0.732728] usbcore: registered new device driver usb [ 0.738803] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported [ 0.746664] i2c i2c-0: IMX I2C adapter registered [ 0.751959] pps_core: LinuxPPS API ver. 1 registered [ 0.756973] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.766302] PTP clock support registered [ 0.770515] EDAC MC: Ver: 3.0.0 [ 0.776356] fsl-ifc 2240000.ifc: Freescale Integrated Flash Controller [ 0.783024] fsl-ifc 2240000.ifc: IFC version 2.0, 8 banks [ 0.788892] FPGA manager framework [ 0.792533] Advanced Linux Sound Architecture Driver Initialized. [ 0.800238] clocksource: Switched to clocksource arch_sys_counter [ 1.384319] VFS: Disk quotas dquot_6.6.0 [ 1.388372] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 1.395856] pnp: PnP ACPI: disabled [ 1.414651] NET: Registered protocol family 2 [ 1.419530] IP idents hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 1.431529] tcp_listen_portaddr_hash hash table entries: 8192 (order: 7, 655360 bytes, linear) [ 1.441124] TCP established hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 1.451091] TCP bind hash table entries: 65536 (order: 10, 4718592 bytes, vmalloc) [ 1.465386] TCP: Hash tables configured (established 131072 bind 65536) [ 1.472971] MPTCP token hash table entries: 16384 (order: 8, 1441792 bytes, linear) [ 1.482764] UDP hash table entries: 8192 (order: 8, 1310720 bytes, linear) [ 1.491641] UDP-Lite hash table entries: 8192 (order: 8, 1310720 bytes, linear) [ 1.501024] NET: Registered protocol family 1 [ 1.506408] RPC: Registered named UNIX socket transport module. [ 1.512412] RPC: Registered udp transport module. [ 1.517165] RPC: Registered tcp transport module. [ 1.521918] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.528425] NET: Registered protocol family 44 [ 1.532953] PCI: CLS 0 bytes, default 64 [ 1.537336] Unpacking initramfs... [ 2.450607] Freeing initrd memory: 21092K [ 2.456455] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 2.464579] kvm [1]: IPA Size Limit: 44 bits [ 2.474877] kvm [1]: vgic-v2@c0e0000 [ 2.478527] kvm [1]: GIC system register CPU interface enabled [ 2.484803] kvm [1]: vgic interrupt IRQ9 [ 2.489163] kvm [1]: Hyp mode initialized successfully [ 2.503268] Initialise system trusted keyrings [ 2.508076] workingset: timestamp_bits=42 max_order=22 bucket_order=0 [ 2.538403] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2.545638] NFS: Registering the id_resolver key type [ 2.550807] Key type id_resolver registered [ 2.555048] Key type id_legacy registered [ 2.559345] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 2.566123] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 2.573849] 9p: Installing v9fs 9p2000 file system support [ 2.602292] Key type asymmetric registered [ 2.606459] Asymmetric key parser 'x509' registered [ 2.611442] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) [ 2.618916] io scheduler mq-deadline registered [ 2.623493] io scheduler kyber registered [ 2.627862] test_firmware: interface ready [ 2.651160] layerscape-pcie 3600000.pcie: host bridge /soc/pcie@3600000 ranges: [ 2.658619] layerscape-pcie 3600000.pcie: IO 0x3000010000..0x300001ffff -> 0x0000000000 [ 2.667273] layerscape-pcie 3600000.pcie: MEM 0x3040000000..0x307fffffff -> 0x0040000000 [ 2.676210] layerscape-pcie 3600000.pcie: PCI host bridge to bus 0000:00 [ 2.682996] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.688543] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 2.694786] pci_bus 0000:00: root bus resource [mem 0x3040000000-0x307fffffff] (bus address [0x40000000-0x7fffffff]) [ 2.705467] pci 0000:00:00.0: [1957:8240] type 01 class 0x060400 [ 2.711555] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x00ffffff] [ 2.717893] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x03ffffff] [ 2.724249] pci 0000:00:00.0: reg 0x38: [mem 0x3048000000-0x3048ffffff pref] [ 2.731503] pci 0000:00:00.0: supports D1 D2 [ 2.735820] pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot [ 2.743165] pci 0000:01:00.0: [8086:10d3] type 00 class 0x020000 [ 2.749317] pci 0000:01:00.0: reg 0x10: [mem 0x3049000000-0x304901ffff] [ 2.756054] pci 0000:01:00.0: reg 0x14: [mem 0x3049080000-0x30490fffff] [ 2.762780] pci 0000:01:00.0: reg 0x18: [io 0x1000-0x101f] [ 2.768453] pci 0000:01:00.0: reg 0x1c: [mem 0x3049100000-0x3049103fff] [ 2.775259] pci 0000:01:00.0: reg 0x30: [mem 0x3049140000-0x304917ffff pref] [ 2.782710] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 2.800857] pci 0000:00:00.0: BAR 1: assigned [mem 0x3040000000-0x3043ffffff] [ 2.808072] pci 0000:00:00.0: BAR 0: assigned [mem 0x3044000000-0x3044ffffff] [ 2.815283] pci 0000:00:00.0: BAR 6: assigned [mem 0x3045000000-0x3045ffffff pref] [ 2.822933] pci 0000:00:00.0: BAR 14: assigned [mem 0x3046000000-0x30460fffff] [ 2.830224] pci 0000:00:00.0: BAR 13: assigned [io 0x1000-0x1fff] [ 2.836475] pci 0000:01:00.0: BAR 1: assigned [mem 0x3046000000-0x304607ffff] [ 2.843694] pci 0000:01:00.0: BAR 6: assigned [mem 0x3046080000-0x30460bffff pref] [ 2.851334] pci 0000:01:00.0: BAR 0: assigned [mem 0x30460c0000-0x30460dffff] [ 2.858551] pci 0000:01:00.0: BAR 3: assigned [mem 0x30460e0000-0x30460e3fff] [ 2.865767] pci 0000:01:00.0: BAR 2: assigned [io 0x1000-0x101f] [ 2.871941] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 2.877221] pci 0000:00:00.0: bridge window [io 0x1000-0x1fff] [ 2.883380] pci 0000:00:00.0: bridge window [mem 0x3046000000-0x30460fffff] [ 2.891683] layerscape-pcie 3700000.pcie: host bridge /soc/pcie@3700000 ranges: [ 2.899142] layerscape-pcie 3700000.pcie: IO 0x3800010000..0x380001ffff -> 0x0000000000 [ 2.907803] layerscape-pcie 3700000.pcie: MEM 0x3840000000..0x387fffffff -> 0x0040000000 [ 2.916702] layerscape-pcie 3700000.pcie: PCI host bridge to bus 0001:00 [ 2.923472] pci_bus 0001:00: root bus resource [bus 00-ff] [ 2.929016] pci_bus 0001:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) [ 2.938055] pci_bus 0001:00: root bus resource [mem 0x3840000000-0x387fffffff] (bus address [0x40000000-0x7fffffff]) [ 2.948710] pci 0001:00:00.0: [1957:8240] type 01 class 0x060400 [ 2.954820] pci 0001:00:00.0: reg 0x38: [mem 0x3840000000-0x38400007ff pref] [ 2.962049] pci 0001:00:00.0: supports D1 D2 [ 2.966365] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot [ 2.974053] pci 0001:00:00.0: BAR 6: assigned [mem 0x3840000000-0x38400007ff pref] [ 2.981697] pci 0001:00:00.0: PCI bridge to [bus 01-ff] [ 2.990040] EINJ: ACPI disabled. [ 3.021225] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 3.033793] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 16, base_baud = 21875000) is a 16550A [ 3.044360] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 16, base_baud = 21875000) is a 16550A [ 3.053378] printk: console [ttyS1] enabled [ 3.053378] printk: console [ttyS1] enabled [ 3.061800] printk: bootconsole [uart8250] disabled [ 3.061800] printk: bootconsole [uart8250] disabled [ 3.073223] 21d0500.serial: ttyS2 at MMIO 0x21d0500 (irq = 17, base_baud = 21875000) is a 16550A [ 3.083599] 21d0600.serial: ttyS3 at MMIO 0x21d0600 (irq = 17, base_baud = 21875000) is a 16550A [ 3.093488] SuperH (H)SCI(F) driver initialized [ 3.098883] msm_serial: driver initialized [ 3.107481] arm-smmu 5000000.iommu: probing hardware configuration... [ 3.113949] arm-smmu 5000000.iommu: SMMUv2 with: [ 3.118584] arm-smmu 5000000.iommu: stage 1 translation [ 3.123913] arm-smmu 5000000.iommu: stage 2 translation [ 3.129243] arm-smmu 5000000.iommu: nested translation [ 3.134484] arm-smmu 5000000.iommu: coherent table walk [ 3.139817] arm-smmu 5000000.iommu: stream matching with 128 register groups [ 3.146976] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) [ 3.153531] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 [ 3.159990] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA [ 3.166448] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA [ 3.202491] loop: module loaded [ 3.206794] lkdtm: No crash points registered, enable through debugfs [ 3.214979] megasas: 07.714.04.00-rc1 [ 3.220857] ahci-qoriq 3200000.sata: supply ahci not found, using dummy regulator [ 3.228718] ahci-qoriq 3200000.sata: supply phy not found, using dummy regulator [ 3.236303] ahci-qoriq 3200000.sata: supply target not found, using dummy regulator [ 3.244349] ahci-qoriq 3200000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 3.253333] ahci-qoriq 3200000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst [ 3.265637] scsi host0: ahci-qoriq [ 3.269845] ata1: SATA max UDMA/133 mmio [mem 0x03200000-0x0320ffff] port 0x100 irq 104 [ 3.278157] ahci-qoriq 3210000.sata: supply ahci not found, using dummy regulator [ 3.285938] ahci-qoriq 3210000.sata: supply phy not found, using dummy regulator [ 3.293498] ahci-qoriq 3210000.sata: supply target not found, using dummy regulator [ 3.301423] ahci-qoriq 3210000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 3.310408] ahci-qoriq 3210000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst [ 3.321459] scsi host1: ahci-qoriq [ 3.325340] ata2: SATA max UDMA/133 mmio [mem 0x03210000-0x0321ffff] port 0x100 irq 105 [ 3.334643] physmap-flash 580000000.nor: physmap platform flash device: [mem 0x580000000-0x587ffffff] [ 3.343951] 580000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002801 [ 3.354076] Amd/Fujitsu Extended Query Table at 0x0040 [ 3.359247] Amd/Fujitsu Extended Query version 1.3. [ 3.364322] number of CFI chips: 1 [ 3.396796] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x48 [ 3.403185] nand: Micron MT29F16G08ABABAWP [ 3.407299] nand: 2048 MiB, SLC, erase size: 512 KiB, page size: 4096, OOB size: 224 [ 3.416494] Bad block table found at page 524160, version 0x01 [ 3.424320] Bad block table found at page 524032, version 0x01 [ 3.455197] fsl,ifc-nand 530000000.nand: IFC NAND device at 0x530000000, bank 2 [ 3.465912] spi-nor spi0.0: unrecognized JEDEC id bytes: 78 f1 e1 c3 c7 8f [ 3.474637] spi-nor spi1.0: unrecognized JEDEC id bytes: 00 00 00 00 00 00 [ 3.481665] spi-nor: probe of spi1.0 failed with error -2 [ 3.494198] thunder_xcv, ver 1.0 [ 3.497533] thunder_bgx, ver 1.0 [ 3.500864] nicpf, ver 1.0 [ 3.505709] hclge is initializing [ 3.509122] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version [ 3.516365] hns3: Copyright (c) 2017 Huawei Corporation. [ 3.521780] e1000: Intel(R) PRO/1000 Network Driver [ 3.526677] e1000: Copyright (c) 1999-2006 Intel Corporation. [ 3.532533] e1000e: Intel(R) PRO/1000 Network Driver [ 3.537514] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 3.543876] e1000e 0000:01:00.0: Adding to iommu group 0 [ 3.550126] e1000e 0000:01:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 3.588548] ata1: SATA link down (SStatus 0 SControl 300) [ 3.609156] e1000e 0000:01:00.0 0000:01:00.0 (uninitialized): registered PHC clock [ 3.646811] ata2: SATA link down (SStatus 0 SControl 300) [ 3.670984] e1000e 0000:01:00.0 eth0: (PCI Express:2.5GT/s:Width x1) 68:05:ca:36:8d:e8 [ 3.678993] e1000e 0000:01:00.0 eth0: Intel(R) PRO/1000 Network Connection [ 3.685910] e1000e 0000:01:00.0 eth0: MAC: 3, PHY: 8, PBA No: E46981-008 [ 3.692751] igb: Intel(R) Gigabit Ethernet Network Driver [ 3.698174] igb: Copyright (c) 2007-2014 Intel Corporation. [ 3.703839] igbvf: Intel(R) Gigabit Virtual Function Network Driver [ 3.710127] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 3.716745] sky2: driver version 1.30 [ 3.722321] VFIO - User Level meta-driver version: 0.3 [ 3.733641] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.740252] ehci-pci: EHCI PCI platform driver [ 3.744777] ehci-platform: EHCI generic platform driver [ 3.750214] ehci-orion: EHCI orion driver [ 3.754441] ehci-exynos: EHCI Exynos driver [ 3.758818] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.765041] ohci-pci: OHCI PCI platform driver [ 3.769564] ohci-platform: OHCI generic platform driver [ 3.774993] ohci-exynos: OHCI Exynos driver [ 3.779901] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 3.785525] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 3.793442] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 [ 3.802943] xhci-hcd xhci-hcd.0.auto: irq 106, io mem 0x03100000 [ 3.811212] hub 1-0:1.0: USB hub found [ 3.815110] hub 1-0:1.0: 1 port detected [ 3.819940] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 3.825469] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 3.833162] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed [ 3.839848] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.849385] hub 2-0:1.0: USB hub found [ 3.853221] hub 2-0:1.0: 1 port detected [ 3.858087] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 3.863623] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 [ 3.871519] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 [ 3.881005] xhci-hcd xhci-hcd.1.auto: irq 107, io mem 0x03110000 [ 3.888786] hub 3-0:1.0: USB hub found [ 3.892621] hub 3-0:1.0: 1 port detected [ 3.897222] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 3.902754] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 [ 3.910447] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 3.917135] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.926469] hub 4-0:1.0: USB hub found [ 3.930298] hub 4-0:1.0: 1 port detected [ 3.935345] usbcore: registered new interface driver usb-storage [ 3.946109] i2c /dev entries driver [ 3.954345] i2c i2c-0: Added multiplexed i2c bus 1 [ 4.064596] rtc-ds3232: probe of 2-0068 failed with error -110 [ 4.070572] i2c i2c-0: Added multiplexed i2c bus 2 [ 4.076259] i2c i2c-0: Added multiplexed i2c bus 3 [ 4.082133] i2c i2c-0: Added multiplexed i2c bus 4 [ 4.087472] i2c i2c-0: Added multiplexed i2c bus 5 [ 4.092767] i2c i2c-0: Added multiplexed i2c bus 6 [ 4.098105] i2c i2c-0: Added multiplexed i2c bus 7 [ 4.103400] i2c i2c-0: Added multiplexed i2c bus 8 [ 4.108265] pca954x 0-0075: registered 8 multiplexed busses for I2C mux pca9547 [ 4.120937] sp805-wdt c000000.wdt: registration successful [ 4.127187] sp805-wdt c010000.wdt: registration successful [ 4.133155] sp805-wdt c100000.wdt: registration successful [ 4.139102] sp805-wdt c110000.wdt: registration successful [ 4.145100] sp805-wdt c200000.wdt: registration successful [ 4.151060] sp805-wdt c210000.wdt: registration successful [ 4.157007] sp805-wdt c300000.wdt: registration successful [ 4.162987] sp805-wdt c310000.wdt: registration successful [ 4.178696] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver [ 4.190532] sdhci: Secure Digital Host Controller Interface driver [ 4.196750] sdhci: Copyright(c) Pierre Ossman [ 4.202031] Synopsys Designware Multimedia Card Interface Driver [ 4.209727] sdhci-pltfm: SDHCI platform and OF driver helper [ 4.218692] ledtrig-cpu: registered to indicate activity on CPUs [ 4.227727] usbcore: registered new interface driver usbhid [ 4.233327] usbhid: USB HID core driver [ 4.243255] optee: probing for conduit method. [ 4.246993] mmc0: SDHCI controller on 2140000.esdhc [2140000.esdhc] using ADMA 64-bit [ 4.247729] optee: api uid mismatch [ 4.259118] optee: probe of firmware:optee failed with error -22 [ 4.268716] netem: version 1.3 [ 4.271848] ipip: IPv4 and MPLS over IPv4 tunneling driver [ 4.278452] gre: GRE over IPv4 demultiplexor driver [ 4.283384] ip_gre: GRE over IPv4 tunneling driver [ 4.290289] IPv4 over IPsec tunneling driver [ 4.296706] NET: Registered protocol family 10 [ 4.303758] Segment Routing with IPv6 [ 4.309265] ip6_gre: GRE over IPv6 tunneling driver [ 4.314984] NET: Registered protocol family 17 [ 4.320102] 9pnet: Installing 9P2000 support [ 4.324601] Key type dns_resolver registered [ 4.329540] registered taskstats version 1 [ 4.333690] Loading compiled-in X.509 certificates [ 4.353983] pcieport 0000:00:00.0: Adding to iommu group 1 [ 4.361204] pcieport 0000:00:00.0: PME: Signaling with IRQ 112 [ 4.368675] pcieport 0001:00:00.0: Adding to iommu group 2 [ 4.375681] pcieport 0001:00:00.0: PME: Signaling with IRQ 116 [ 4.452511] IP-Config: Failed to open gretap0 [ 4.457325] IP-Config: Failed to open erspan0 [ 4.480273] Sending DHCP requests . [ 7.033399] e1000e 0000:01:00.0 eth0: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None [ 7.046161] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 7.264320] ., OK [ 8.314501] IP-Config: Got DHCP answer from 172.16.1.4, my address is 172.16.1.171 [ 8.322169] IP-Config: Complete: [ 8.325460] device=eth0, hwaddr=68:05:ca:36:8d:e8, ipaddr=172.16.1.171, mask=255.255.255.0, gw=172.16.1.4 [ 8.335520] host=172.16.1.171, domain=example.org, nis-domain=(none) [ 8.342363] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= [ 8.342378] nameserver0=172.16.1.4 [ 8.353996] ALSA device list: [ 8.357155] No soundcards found. [ 8.380393] Freeing unused kernel memory: 9728K [ 8.385146] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: [ 8.517295] udevd[192]: starting version 3.2.9 [ 8.523213] random: udevd: uninitialized urandom read (16 bytes read) [ 8.530253] random: udevd: uninitialized urandom read (16 bytes read) [ 8.536776] random: udevd: uninitialized urandom read (16 bytes read) [ 8.548025] udevd[192]: specified user 'tss' unknown [ 8.553109] udevd[192]: specified group 'tss' unknown [ 8.561652] udevd[193]: starting eudev-3.2.9 [ 9.049764] udevd[205]: Error changing net interface name eth0 to enp1s0: Device or resource busy [ 9.060200] ina2xx 3-0040: error configuring the device: -11 [ 9.060343] lm90 4-004c: supply vcc not found, using dummy regulator [ 9.060564] udevd[205]: could not rename interface '2' from 'eth0' to 'enp1s0': Device or resource busy [ 9.082615] lm90 4-004c: Failed to initialize device [ 9.088632] lm90: probe of 4-004c failed with error -11 done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1144382/environment . /lava-1144382/environment / # /lava-1144382/bin/lava-test-runner /lava-1144382/0 /lava-1144382/bin/lava-test-runner /lava-1144382/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1144382/0/tests/0_dmesg + cat uuid + UUID=1144382_1.5[ 9.839382] .2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh [ 9.890245] [ 9.937265] [ 9.988986] + set +x[ 10.000827] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-1144382/environment / # . /lava-1144382/environment/lava-1144382/bin/lava-test-runner /lava-1144382/1 / # /lava-1144382/bin/lava-test-runner /lava-1144382/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1144382/1/tests/1_bootrr + cat uuid [ 10.489273] + UUID=1144382_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-1144382/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto 8000000.crypto /lava-1144382/1/../bin/lava-test-case [ 11.558274] /lava-1144382/1/../bin/lava-test-case [ 11.607480] /lava-1144382/1/../bin/lava-test-case [ 11.635446] + set +x [ 11.662044] / #