[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.36 (3 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 9034262/tftp-deploy-clvnhocj/kernel/zImage tftp 0x10000000 9034262/tftp-deploy-clvnhocj/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.36 Filename '9034262/tftp-deploy-clvnhocj/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################### 9.9 MiB/s done Bytes transferred = 12362240 (bca200 hex) => tftp 0x14000000 9034262/tftp-deploy-clvnhocj/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 9034262/tftp-deploy-clvnhocj/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.36 Filename '9034262/tftp-deploy-clvnhocj/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############ 9.6 MiB/s done Bytes transferred = 15436971 (eb8cab hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 9034262/tftp-deploy-clvnhocj/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 9034262/tftp-deploy-clvnhocj/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.36 Filename '9034262/tftp-deploy-clvnhocj/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 5.1 MiB/s done Bytes transferred = 42449 (a5d1 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/9034262/extract-nfsrootfs-8kl95y8s,tcp,hard console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/9034262/extract-nfsrootfs-8kl95y8s,tcp,hard console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0xbca200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 15436907 Bytes = 14.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d5d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.167-cip25 (KernelCI@build-j990307-arm-gcc-10-multi-v7-defconfig-kselftest-mz9b6) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Mon Feb 6 11:24:13 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 21 pages/cpu s55468 r8192 d22356 u86016 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/9034262/extract-nfsrootfs-8kl95y8s,tcp,hard console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 921444K/1048576K available (17408K kernel code, 2652K rwdata, 8104K rodata, 2048K init, 6694K bss, 61596K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] ftrace: allocating 55514 entries in 163 pages <6>[ 0.000000] ftrace: allocated 163 pages with 4 groups <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] Rude variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000009] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008446] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022849] Console: colour dummy device 80x30 <4>[ 0.024755] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.032763] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.037107] ... MAX_LOCK_DEPTH: 48 <4>[ 0.041517] ... MAX_LOCKDEP_KEYS: 8192 <4>[ 0.046154] ... CLASSHASH_SIZE: 4096 <4>[ 0.050740] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.055462] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.060136] ... CHAINHASH_SIZE: 32768 <4>[ 0.064834] memory used by lock dependency info: 4061 kB <4>[ 0.070514] memory used for stack traces: 2112 kB <4>[ 0.075559] per task-struct memory footprint: 1536 bytes <6>[ 0.081245] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.091665] pid_max: default: 32768 minimum: 301 <6>[ 0.096895] LSM: Security Framework initializing <6>[ 0.101457] LSM support for eBPF active <6>[ 0.105618] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.113055] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.123659] CPU: Testing write buffer coherency: ok <6>[ 0.126214] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.132437] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.141317] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.147726] rcu: Hierarchical SRCU implementation. <6>[ 0.159679] EFI services will not be available. <6>[ 0.162921] smp: Bringing up secondary CPUs ... <6>[ 0.169732] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.169748] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.182123] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.182138] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.194165] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.194181] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.203402] smp: Brought up 1 node, 4 CPUs <6>[ 0.207054] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.213369] CPU: All CPU(s) started in SVC mode. <6>[ 0.220995] devtmpfs: initialized <6>[ 0.279782] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.287605] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.295080] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.307067] pinctrl core: initialized pinctrl subsystem <6>[ 0.316599] DMI not present or invalid. <6>[ 0.320150] NET: Registered protocol family 16 <6>[ 0.334242] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.348073] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.348630] cpuidle: using governor menu <6>[ 0.356791] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 1.080673] vdd1p1: supplied by regulator-dummy <6>[ 1.113318] vdd3p0: supplied by regulator-dummy <6>[ 1.145817] vdd2p5: supplied by regulator-dummy <6>[ 1.178195] vddarm: supplied by regulator-dummy <6>[ 1.211480] vddpu: supplied by regulator-dummy <6>[ 1.242720] vddsoc: supplied by regulator-dummy <6>[ 2.533016] No ATAGs? <6>[ 2.533994] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 2.541078] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 2.566333] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 2.599309] Serial: AMBA PL011 UART driver <6>[ 2.665179] Kprobes globally optimized <6>[ 2.785203] iommu: Default domain type: Translated <6>[ 2.789962] vgaarb: loaded <5>[ 2.795182] SCSI subsystem initialized <6>[ 2.799010] usbcore: registered new interface driver usbfs <6>[ 2.802397] usbcore: registered new interface driver hub <6>[ 2.807953] usbcore: registered new device driver usb <6>[ 2.820627] i2c i2c-0: IMX I2C adapter registered <6>[ 2.829973] i2c i2c-1: IMX I2C adapter registered <6>[ 2.836734] i2c i2c-2: IMX I2C adapter registered <6>[ 2.843334] pps_core: LinuxPPS API ver. 1 registered <6>[ 2.845803] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 2.855200] PTP clock support registered <6>[ 2.878619] clocksource: Switched to clocksource mxc_timer1 <6>[ 4.617698] NET: Registered protocol family 2 <6>[ 4.620355] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 4.630635] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 22528 bytes, linear) <6>[ 4.636660] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 4.644791] TCP bind hash table entries: 8192 (order: 6, 327680 bytes, linear) <6>[ 4.653494] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 4.659919] MPTCP token hash table entries: 1024 (order: 3, 49152 bytes, linear) <6>[ 4.666582] UDP hash table entries: 512 (order: 3, 49152 bytes, linear) <6>[ 4.673454] UDP-Lite hash table entries: 512 (order: 3, 49152 bytes, linear) <6>[ 4.681241] NET: Registered protocol family 1 <6>[ 4.687791] RPC: Registered named UNIX socket transport module. <6>[ 4.691403] RPC: Registered udp transport module. <6>[ 4.696207] RPC: Registered tcp transport module. <6>[ 4.701292] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 4.707878] NET: Registered protocol family 44 <6>[ 4.712638] PCI: CLS 0 bytes, default 64 <6>[ 4.719405] Trying to unpack rootfs image as initramfs... <6>[ 6.633267] Freeing initrd memory: 15076K <4>[ 6.636177] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 6.643283] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 6.659735] Initialise system trusted keyrings <6>[ 6.662665] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 6.720335] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 6.727311] NFS: Registering the id_resolver key type <5>[ 6.730041] Key type id_resolver registered <5>[ 6.734255] Key type id_legacy registered <6>[ 6.739182] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 6.745525] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 6.753369] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 6.759956] Key type asymmetric registered <5>[ 6.762167] Asymmetric key parser 'x509' registered <6>[ 6.767575] bounce: pool size: 64 pages <6>[ 6.771507] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 6.779097] io scheduler mq-deadline registered <6>[ 6.783743] io scheduler kyber registered <4>[ 6.789031] test_firmware: interface ready <6>[ 6.970779] mxs-dma 110000.dma-apbh: initialized <4>[ 7.037241] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 7.044514] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 7.307883] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 7.332458] SuperH (H)SCI(F) driver initialized <6>[ 7.337399] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 7.348783] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 7.355249] printk: console [ttymxc1] enabled <6>[ 7.355249] printk: console [ttymxc1] enabled <6>[ 7.364143] printk: bootconsole [ec_imx21] disabled <6>[ 7.364143] printk: bootconsole [ec_imx21] disabled <6>[ 7.380869] msm_serial: driver initialized <6>[ 7.386294] STMicroelectronics ASC driver initialized <6>[ 7.398225] STM32 USART driver initialized <6>[ 7.425012] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 0 <4>[ 7.447524] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.456275] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.464447] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.520333] brd: module loaded <6>[ 7.583871] loop: module loaded <6>[ 7.590750] lkdtm: No crash points registered, enable through debugfs <6>[ 7.613163] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 7.621472] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 7.629851] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 7.638400] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 7.646661] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 7.655201] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 7.663297] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 7.674968] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 7.682362] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 7.691520] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 7.706325] scsi host0: ahci-imx <6>[ 7.712340] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 7.778210] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 7.792123] pps pps0: new PPS source ptp0 <6>[ 7.838908] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 7.849952] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 7.855217] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 7.861754] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 7.867450] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 7.895502] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 7.903425] usbcore: registered new interface driver pegasus <6>[ 7.909651] usbcore: registered new interface driver asix <6>[ 7.915509] usbcore: registered new interface driver ax88179_178a <6>[ 7.922103] usbcore: registered new interface driver cdc_ether <6>[ 7.928515] usbcore: registered new interface driver smsc75xx <6>[ 7.934763] usbcore: registered new interface driver smsc95xx <6>[ 7.941004] usbcore: registered new interface driver net1080 <6>[ 7.947098] usbcore: registered new interface driver cdc_subset <6>[ 7.953542] usbcore: registered new interface driver zaurus <6>[ 7.959728] usbcore: registered new interface driver cdc_ncm <6>[ 7.978636] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 7.985541] ehci-pci: EHCI PCI platform driver <6>[ 7.990494] ehci-platform: EHCI generic platform driver <6>[ 7.997030] ehci-orion: EHCI orion driver <6>[ 8.002314] SPEAr-ehci: EHCI SPEAr driver <6>[ 8.007492] ehci-st: EHCI STMicroelectronics driver <6>[ 8.013592] ehci-exynos: EHCI Exynos driver <6>[ 8.018991] ehci-atmel: EHCI Atmel driver <6>[ 8.024144] tegra-ehci: Tegra EHCI driver <6>[ 8.029406] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 8.035955] ohci-pci: OHCI PCI platform driver <6>[ 8.040922] ohci-platform: OHCI generic platform driver <6>[ 8.047391] SPEAr-ohci: OHCI SPEAr driver <6>[ 8.052681] ohci-st: OHCI STMicroelectronics driver <6>[ 8.058791] ohci-atmel: OHCI Atmel driver <6>[ 8.061060] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 8.066573] usbcore: registered new interface driver usb-storage <6>[ 8.069232] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 8.081786] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 8.108391] i2c /dev entries driver <6>[ 8.195967] sdhci: Secure Digital Host Controller Interface driver <6>[ 8.202519] sdhci: Copyright(c) Pierre Ossman <6>[ 8.216803] Synopsys Designware Multimedia Card Interface Driver <6>[ 8.230628] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 8.240455] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 8.240461] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 8.251318] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 8.258132] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 8.268278] usbcore: registered new interface driver usbhid <6>[ 8.274155] usbhid: USB HID core driver <6>[ 8.279644] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 8.291843] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 8.308399] netem: version 1.3 <6>[ 8.312004] ipip: IPv4 and MPLS over IPv4 tunneling driver <6>[ 8.320534] gre: GRE over IPv4 demultiplexor driver <6>[ 8.325714] ip_gre: GRE over IPv4 tunneling driver <6>[ 8.336951] IPv4 over IPsec tunneling driver <6>[ 8.346799] NET: Registered protocol family 10 <6>[ 8.358659] Segment Routing with IPv6 <6>[ 8.369243] ip6_gre: GRE over IPv6 tunneling driver <6>[ 8.377461] NET: Registered protocol family 17 <5>[ 8.384279] Key type dns_resolver registered <6>[ 8.404896] ThumbEE CPU extension supported. <5>[ 8.409598] Registering SWP/SWPB emulation handler <5>[ 8.416037] Loading compiled-in X.509 certificates <6>[ 8.455762] mmc2: new high speed SDHC card at address aaaa <6>[ 8.465421] mmcblk2: mmc2:aaaa SL16G 14.8 GiB <4>[ 8.485884] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 8.493756] GPT:29296874 != 31116287 <4>[ 8.497629] GPT:Alternate GPT header not at the end of the disk. <4>[ 8.503976] GPT:29296874 != 31116287 <4>[ 8.507844] GPT: Use GNU Parted to correct GPT errors. <6>[ 8.513381] mmcblk2: p1 p2 p3 <4>[ 8.603687] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.612386] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.625760] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.665159] imx_usb 2184200.usb: No over current polarity defined <6>[ 8.681734] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 8.687239] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 8.718996] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 8.741915] hub 1-0:1.0: USB hub found <6>[ 8.747082] hub 1-0:1.0: 1 port detected <6>[ 8.763592] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 8.795984] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.804594] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.817967] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.848915] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.857436] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.870889] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.890256] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 8.919289] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.927896] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.941307] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.964060] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <3>[ 8.979857] IP-Config: Failed to open gretap0 <3>[ 8.984520] IP-Config: Failed to open erspan0 <5>[ 9.018321] Sending DHCP requests . <6>[ 9.138450] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 9.357709] hub 1-1:1.0: USB hub found <6>[ 9.362415] hub 1-1:1.0: 3 ports detected <4>[ 9.392981] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.401605] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.415235] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 11.788295] . <6>[ 12.079849] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 12.090549] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <3>[ 15.743347] DHCP/BOOTP: Reply not for us on eth0, op[2] xid[ddb90a8f] <4>[ 16.628354] ., OK <6>[ 16.671117] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.36 <6>[ 16.679721] IP-Config: Complete: <6>[ 16.683297] device=eth0, hwaddr=00:19:b8:08:f1:1c, ipaddr=192.168.201.36, mask=255.255.255.0, gw=192.168.201.1 <6>[ 16.694261] host=imx6q-sabrelite-lava-cbg-6, domain=lava-rack, nis-domain=(none) <6>[ 16.702554] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 16.702601] nameserver0=192.168.201.1 <6>[ 16.774947] Freeing unused kernel memory: 2048K <6>[ 16.781338] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u1 <6>[ 20.914386] imx-ipuv3 2400000.ipu: IPUv3H probed <4>[ 20.959293] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 20.977685] panel-simple panel-lcd: Specify missing connector_type <6>[ 20.988301] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 20.992407] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 20.997313] CAN device driver interface <4>[ 21.037032] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 21.050216] panel-simple panel-lcd: Specify missing connector_type <4>[ 21.063979] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 21.148835] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 21.159498] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 21.168740] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 21.175627] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 21.185855] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 21.194673] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 21.201274] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 21.211024] caam 2100000.crypto: Entropy delay = 3200 <6>[ 21.211157] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 1 <4>[ 21.235976] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 21.244721] panel-simple panel-lcd: Specify missing connector_type <4>[ 21.258849] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 21.277155] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 21.337922] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 21.343457] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 21.350436] caam 2100000.crypto: job rings = 2, qi = 0 <4>[ 21.386012] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 21.394987] panel-simple panel-lcd: Specify missing connector_type <4>[ 21.409792] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 21.441409] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 21.451190] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <4>[ 21.455819] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <6>[ 21.460592] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <4>[ 21.468621] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 21.472728] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 21.473617] panel-simple panel-lcd: Specify missing connector_type <6>[ 21.476870] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 21.480948] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 21.519604] sgtl5000 0-000a: sgtl5000 revision 0x11 <4>[ 21.532542] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 21.535842] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 21.541327] panel-simple panel-lcd: Specify missing connector_type <4>[ 21.549233] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <4>[ 21.576890] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 21.588257] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 21.622744] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 21.631813] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 21.640771] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 21.649571] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 21.684836] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 21.693701] panel-simple panel-lcd: Specify missing connector_type <4>[ 21.726004] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 21.821901] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 21.830872] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 21.839746] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 21.848520] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 21.871856] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 21.889909] panel-simple panel-lcd: Specify missing connector_type <6>[ 22.437727] caam algorithms registered in /proc/crypto <6>[ 22.459420] caam 2100000.crypto: registering rng-caam <4>[ 22.473651] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 22.512236] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 22.521022] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 22.529900] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 22.538685] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 22.553707] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 22.563850] panel-simple panel-lcd: Specify missing connector_type Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/erspan0 found done. <5>[ 22.649200] random: crng init done IP-Config: erspan0 hardware address 00:00:00:00:00:00 mtu 1450 DHCP SIOCSIFFLAGS: Cannot assign requested address IP-Config: gretap0 hardware address 00:00:00:00:00:00 mtu 1462 DHCP SIOCSIFFLAGS: Cannot assign requested address IP-Config: eth0 hardware address 00:19:b8:08:f1:1c mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.36 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-6 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 24.942669] systemd[1]: System time before build time, advancing clock. <30>[ 25.609874] systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 25.636247] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! <30>[ 25.705542] systemd[1]: Set hostname to . <30>[ 27.320461] systemd[1]: Queued start job for default target Graphical Interface. <30>[ 27.335276] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. <30>[ 27.383781] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. <30>[ 27.443959] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. <30>[ 27.493108] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. <30>[ 27.542814] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. <30>[ 27.602042] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. <30>[ 27.651218] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 27.664589] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. <30>[ 27.709727] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. <30>[ 27.748993] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. <30>[ 27.788888] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. <30>[ 27.828713] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. <30>[ 27.872846] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. <30>[ 27.980477] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. <30>[ 27.995232] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). <30>[ 28.045625] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. <30>[ 28.095227] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. <30>[ 28.150927] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. <30>[ 28.191366] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. <30>[ 28.232768] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 28.245108] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. <30>[ 28.268962] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... <30>[ 28.334071] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... <30>[ 28.405216] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... <30>[ 28.459375] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... <30>[ 28.523469] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... <30>[ 28.578960] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... <30>[ 28.670627] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. <6>[ 28.705317] fuse: init (API version 7.32) <30>[ 28.712082] systemd[1]: Starting Journal Service... Starting Journal Service... <30>[ 28.784714] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... <30>[ 28.842669] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... <30>[ 28.908443] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... <30>[ 28.952192] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. <30>[ 29.000355] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. <30>[ 29.047053] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. <30>[ 29.142841] systemd[1]: modprobe@configfs.service: Succeeded. <30>[ 29.153692] systemd[1]: Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module configfs. <30>[ 29.204291] systemd[1]: modprobe@drm.service: Succeeded. <30>[ 29.215805] systemd[1]: Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module drm. <30>[ 29.274334] systemd[1]: modprobe@fuse.service: Succeeded. <30>[ 29.284874] systemd[1]: Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Module fuse. <30>[ 29.344430] systemd[1]: Finished Load Kernel Modules. [ OK ] Finished Load Kernel Modules. <30>[ 29.393952] systemd[1]: Finished Remount Root and Kernel File Systems. [ OK ] Finished Remount Root and Kernel File Systems. <30>[ 29.450959] systemd[1]: Mounting FUSE Control File System... Mounting FUSE Control File System... <30>[ 29.508817] systemd[1]: Mounting Kernel Configuration File System... Mounting Kernel Configuration File System... <30>[ 29.568848] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped. <30>[ 29.578994] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped. <30>[ 29.598300] systemd[1]: Starting Load/Save Random Seed... Starting Load/Save Random Seed... <30>[ 29.658487] systemd[1]: Starting Apply Kernel Variables... Starting Apply Kernel Variables... <30>[ 29.720309] systemd[1]: Starting Create System Users... Starting Create System Users... <30>[ 29.765584] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Mounted FUSE Control File System. [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. Starting Flush Journal to Persistent Storage... Starting Create Static Device Nodes in /dev... <46>[ 30.159891] systemd-journald[287]: Received client request to flush runtime journal. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Rule-based Manage…for Device Events and Files... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... Starting Create Volatile Files and Directories... [ OK ] Started Network Service. [ OK ] Finished Create Volatile Files and Directories. Starting Network Name Resolution... Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Network Name Resolution. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Found device /dev/ttymxc1. [ OK ] Finished Coldplug All udev Devices. [ OK ] Reached target System Initialization. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 5.10.167-cip25 #1 SMP Mon Feb 6 11:24:13 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/9034262/extract-nfsrootfs-8kl95y8s' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/9034262/extract-nfsrootfs-8kl95y8s' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-9034262/environment . /lava-9034262/environment / # /lava-9034262/bin/lava-test-runner /lava-9034262/0 /lava-9034262/bin/lava-test-runner /lava-9034262/0 + export TESTRUN_ID=0_dmesg + cd /lava-9034262/0/tests/0_dmesg + cat uuid + UUID=9034262_1.6.2.4.1<8>[ 49.129809] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 49.363624] <8>[ 49.557932] <8>[ 49.751010] + set +x <8>[ 49.762819] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-9034262/environment / # . /lava-9034262/environment/lava-9034262/bin/lava-test-runner /lava-9034262/1 / # /lava-9034262/bin/lava-test-runner /lava-9034262/1 + export TESTRUN_ID=1_bootrr + cd /lava-9034262/1/tests/1_bootrr + cat uuid + UUID=9034262_1.6.2.4.5<8>[ 50.557165] + set +x + export PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-9034262/1/../bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto panel-lvds0 backlight-lcd backlight-lvds ldb panel-lcd /lava-9034262/1/../bin/lava-test-case <8>[ 51.919840] /lava-9034262/1/../bin/lava-test-case <8>[ 52.108346] /lava-9034262/1/../bin/lava-test-case <8>[ 52.196809] + set +x <8>[ 52.270263] / #