[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.0 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected sst25vf016b with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 6 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.101.101 (3 ms) => setenv serverip 192.168.101.1 setenv serverip 192.168.101.1 => tftp 0x10000000 9273474/tftp-deploy-n18h6wnv/kernel/zImage tftp 0x10000000 9273474/tftp-deploy-n18h6wnv/kernel/zImage Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.101 Filename '9273474/tftp-deploy-n18h6wnv/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 3 MiB/s done Bytes transferred = 9687552 (93d200 hex) => tftp 0x14000000 9273474/tftp-deploy-n18h6wnv/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 9273474/tftp-deploy-n18h6wnv/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.101 Filename '9273474/tftp-deploy-n18h6wnv/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ###################################################### 3 MiB/s done Bytes transferred = 16048844 (f4e2cc hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 9273474/tftp-deploy-n18h6wnv/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 9273474/tftp-deploy-n18h6wnv/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.101 Filename '9273474/tftp-deploy-n18h6wnv/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 2.4 MiB/s done Bytes transferred = 42449 (a5d1 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x93d200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16048780 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d5d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.167-cip26 (KernelCI@build-j1079666-arm-gcc-10-multi-v7-defconfig-vm5vs) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Feb 22 04:04:08 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 933712K/1048576K available (13312K kernel code, 2233K rwdata, 5348K rodata, 2048K init, 426K bss, 49328K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 15ns <6>[ 0.000007] sched_clock: 32 bits at 66MHz, resolution 15ns, wraps every 32537631224ns <6>[ 0.008093] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 28958491609 ns <6>[ 0.021724] Console: colour dummy device 80x30 <6>[ 0.023613] Calibrating delay loop (skipped), value calculated using timer frequency.. 132.00 BogoMIPS (lpj=660000) <6>[ 0.034288] pid_max: default: 32768 minimum: 301 <6>[ 0.039321] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.046741] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.055348] CPU: Testing write buffer coherency: ok <6>[ 0.059870] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.065403] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.071779] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079453] rcu: Hierarchical SRCU implementation. <6>[ 0.086425] EFI services will not be available. <6>[ 0.088655] smp: Bringing up secondary CPUs ... <6>[ 0.093938] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.093945] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.105281] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.105289] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.116485] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.116492] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.126943] smp: Brought up 1 node, 4 CPUs <6>[ 0.131169] SMP: Total of 4 processors activated (528.00 BogoMIPS). <6>[ 0.137712] CPU: All CPU(s) started in SVC mode. <6>[ 0.143135] devtmpfs: initialized <6>[ 0.153487] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.158821] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.168699] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.178892] pinctrl core: initialized pinctrl subsystem <6>[ 0.183314] DMI not present or invalid. <6>[ 0.186487] NET: Registered protocol family 16 <6>[ 0.193779] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.200369] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.200560] cpuidle: using governor menu <6>[ 0.208689] CPU identified as i.MX6Q, silicon rev 1.0 <6>[ 0.389890] vdd1p1: supplied by regulator-dummy <6>[ 0.399095] vdd3p0: supplied by regulator-dummy <6>[ 0.408253] vdd2p5: supplied by regulator-dummy <6>[ 0.417438] vddarm: supplied by regulator-dummy <6>[ 0.426740] vddpu: supplied by regulator-dummy <6>[ 0.435629] vddsoc: supplied by regulator-dummy <6>[ 0.769196] No ATAGs? <6>[ 0.769383] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.777159] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.787402] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.797774] Serial: AMBA PL011 UART driver <6>[ 0.801960] printk: console [ramoops-1] enabled <6>[ 0.804268] pstore: Registered ramoops as persistent store backend <6>[ 0.810527] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.848223] iommu: Default domain type: Translated <6>[ 0.850979] vgaarb: loaded <5>[ 0.854329] SCSI subsystem initialized <6>[ 0.858046] usbcore: registered new interface driver usbfs <6>[ 0.863268] usbcore: registered new interface driver hub <6>[ 0.868848] usbcore: registered new device driver usb <6>[ 0.875621] i2c i2c-0: IMX I2C adapter registered <6>[ 0.880433] i2c i2c-1: IMX I2C adapter registered <6>[ 0.884825] i2c i2c-2: IMX I2C adapter registered <6>[ 0.890360] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.894190] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.903622] PTP clock support registered <6>[ 0.911359] clocksource: Switched to clocksource mxc_timer1 <6>[ 1.964047] NET: Registered protocol family 2 <6>[ 1.966254] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.974687] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 1.982145] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 1.990173] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 1.997641] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 2.004339] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.011013] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.018481] NET: Registered protocol family 1 <6>[ 2.023569] RPC: Registered named UNIX socket transport module. <6>[ 2.029070] RPC: Registered udp transport module. <6>[ 2.034065] RPC: Registered tcp transport module. <6>[ 2.038986] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.045711] PCI: CLS 0 bytes, default 64 <6>[ 2.050344] Trying to unpack rootfs image as initramfs... <6>[ 3.396784] Freeing initrd memory: 15676K <4>[ 3.398653] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.406130] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.415779] Initialise system trusted keyrings <6>[ 3.418962] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.431224] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.435213] NFS: Registering the id_resolver key type <5>[ 3.439810] Key type id_resolver registered <5>[ 3.444238] Key type id_legacy registered <6>[ 3.448573] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.455456] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.463137] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.468166] Key type asymmetric registered <5>[ 3.472076] Asymmetric key parser 'x509' registered <6>[ 3.477228] bounce: pool size: 64 pages <6>[ 3.481326] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.488934] io scheduler mq-deadline registered <6>[ 3.493732] io scheduler kyber registered <6>[ 3.537873] mxs-dma 110000.dma-apbh: initialized <4>[ 3.544792] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.551723] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 3.601720] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.609885] SuperH (H)SCI(F) driver initialized <6>[ 3.612885] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.621720] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 3.629605] printk: console [ttymxc1] enabled <6>[ 3.629605] printk: console [ttymxc1] enabled <6>[ 3.638810] printk: bootconsole [ec_imx21] disabled <6>[ 3.638810] printk: bootconsole [ec_imx21] disabled <6>[ 3.650627] msm_serial: driver initialized <6>[ 3.656544] STMicroelectronics ASC driver initialized <6>[ 3.663886] STM32 USART driver initialized <4>[ 3.679454] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.687384] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.694160] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.710810] brd: module loaded <6>[ 3.724330] loop: module loaded <6>[ 3.731773] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.739970] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.748275] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.756750] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.764767] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.772524] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.780093] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.790707] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.797989] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.807067] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.817857] scsi host0: ahci-imx <6>[ 3.821744] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 3.842498] CAN device driver interface <6>[ 3.847926] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.857488] pps pps0: new PPS source ptp0 <6>[ 3.894400] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.902063] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.907298] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.913559] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.919226] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.931246] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.938975] usbcore: registered new interface driver pegasus <6>[ 3.944966] usbcore: registered new interface driver asix <6>[ 3.950667] usbcore: registered new interface driver ax88179_178a <6>[ 3.957078] usbcore: registered new interface driver cdc_ether <6>[ 3.963248] usbcore: registered new interface driver smsc75xx <6>[ 3.969304] usbcore: registered new interface driver smsc95xx <6>[ 3.975366] usbcore: registered new interface driver net1080 <6>[ 3.981350] usbcore: registered new interface driver cdc_subset <6>[ 3.987568] usbcore: registered new interface driver zaurus <6>[ 3.993493] usbcore: registered new interface driver cdc_ncm <6>[ 4.003088] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 4.009885] ehci-pci: EHCI PCI platform driver <6>[ 4.014656] ehci-platform: EHCI generic platform driver <6>[ 4.020456] ehci-orion: EHCI orion driver <6>[ 4.024990] SPEAr-ehci: EHCI SPEAr driver <6>[ 4.029449] ehci-st: EHCI STMicroelectronics driver <6>[ 4.034802] ehci-exynos: EHCI Exynos driver <6>[ 4.039435] ehci-atmel: EHCI Atmel driver <6>[ 4.043909] tegra-ehci: Tegra EHCI driver <6>[ 4.048405] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.054887] ohci-pci: OHCI PCI platform driver <6>[ 4.059641] ohci-platform: OHCI generic platform driver <6>[ 4.065432] SPEAr-ohci: OHCI SPEAr driver <6>[ 4.069901] ohci-st: OHCI STMicroelectronics driver <6>[ 4.075266] ohci-atmel: OHCI Atmel driver <6>[ 4.080616] usbcore: registered new interface driver usb-storage <6>[ 4.095173] i2c /dev entries driver <6>[ 4.118636] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.125109] sdhci: Copyright(c) Pierre Ossman <6>[ 4.132511] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.140764] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.148441] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 4.152109] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 4.153747] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 4.164357] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 4.170077] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 4.176649] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 4.184090] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.190692] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 4.191479] usbcore: registered new interface driver usbhid <6>[ 4.198479] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 4.203689] usbhid: USB HID core driver <6>[ 4.210277] NET: Registered protocol family 10 <6>[ 4.220625] Segment Routing with IPv6 <6>[ 4.224662] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.231453] NET: Registered protocol family 17 <6>[ 4.236174] can: controller area network core <6>[ 4.240868] NET: Registered protocol family 29 <6>[ 4.245604] can: raw protocol <6>[ 4.246168] mmc2: new high speed SDHC card at address 0001 <6>[ 4.248842] can: broadcast manager protocol <6>[ 4.255509] mmcblk2: mmc2:0001 SD 14.8 GiB <6>[ 4.259069] can: netlink gateway - max_hops=1 <5>[ 4.268685] Key type dns_resolver registered <6>[ 4.275119] ThumbEE CPU extension supported. <5>[ 4.279674] Registering SWP/SWPB emulation handler <4>[ 4.283350] GPT:Primary header thinks Alt. header is not at the end of the disk. <5>[ 4.285021] Loading compiled-in X.509 certificates <4>[ 4.292415] GPT:29296874 != 30965759 <4>[ 4.292419] GPT:Alternate GPT header not at the end of the disk. <4>[ 4.292423] GPT:29296874 != 30965759 <4>[ 4.292431] GPT: Use GNU Parted to correct GPT errors. <6>[ 4.302782] pstore: Using crash dump compression: deflate <6>[ 4.307737] mmcblk2: p1 p2 p3 <4>[ 4.337350] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.345311] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.353642] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.371045] imx_usb 2184200.usb: No over current polarity defined <6>[ 4.381068] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 4.386300] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 4.421394] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 4.428421] hub 1-0:1.0: USB hub found <6>[ 4.432574] hub 1-0:1.0: 1 port detected <3>[ 4.440852] imx_thermal 20c8000.anatop:tempmon: invalid sensor calibration data <3>[ 4.448501] imx_thermal 20c8000.anatop:tempmon: error -EINVAL: failed to init from nvmem <4>[ 4.456903] imx_thermal: probe of 20c8000.anatop:tempmon failed with error -22 <4>[ 4.469216] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.477176] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.485428] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.498648] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.506596] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.514852] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.525271] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.538429] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.546414] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.554755] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.568580] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:06: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:06, irq=POLL) <6>[ 4.781404] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 4.983112] hub 1-1:1.0: USB hub found <6>[ 4.987321] hub 1-1:1.0: 3 ports detected <4>[ 5.002231] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 5.010276] panel-simple panel-lcd: Specify missing connector_type <4>[ 5.020255] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 6.641921] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx <6>[ 6.651433] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 6.681432] Sending DHCP requests ., OK <6>[ 6.725609] IP-Config: Got DHCP answer from 192.168.101.1, my address is 192.168.101.101 <6>[ 6.734029] IP-Config: Complete: <6>[ 6.737551] device=eth0, hwaddr=00:19:b8:00:e5:47, ipaddr=192.168.101.101, mask=255.255.255.0, gw=192.168.101.1 <6>[ 6.748400] host=imx6q-sabrelite-cbg-2, domain=lava.cbg.collabora.co.uk, nis-domain=(none) <6>[ 6.757420] bootserver=192.168.101.1, rootserver=192.168.101.1, rootpath= <6>[ 6.757433] nameserver0=192.168.101.1 <6>[ 6.776415] Freeing unused kernel memory: 2048K <6>[ 6.802325] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 6.970399] udevd[135]: starting version 3.2.9 <5>[ 6.976337] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.983421] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.990247] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 7.005750] udevd[135]: specified user 'tss' unknown <27>[ 7.011207] udevd[135]: specified group 'tss' unknown <30>[ 7.019262] udevd[136]: starting eudev-3.2.9 <6>[ 7.370185] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 7.377957] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 7.399041] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.407092] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.454534] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 7.500085] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.508121] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.539945] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 7.548136] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 7.556893] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 7.565066] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <4>[ 7.658149] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.681658] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <4>[ 7.687641] panel-simple panel-lcd: supply power not found, using dummy regulator <6>[ 7.690310] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <4>[ 7.698133] panel-simple panel-lcd: Specify missing connector_type <6>[ 7.706634] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <4>[ 7.715674] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.721526] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 7.735617] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.745771] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.782076] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 7.797595] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.805621] panel-simple panel-lcd: Specify missing connector_type <6>[ 7.862152] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.869271] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.876641] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.883487] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 7.911572] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 7.919025] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 7.925487] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 7.941690] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <6>[ 8.031393] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.039952] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.048588] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.057147] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.073268] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.112706] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.120674] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.132131] caam 2100000.crypto: Entropy delay = 3200 <6>[ 8.198270] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 8.198611] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.212339] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.220916] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.229485] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 8.256545] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 8.259021] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 8.267152] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 8.274097] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 8.290192] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <4>[ 8.294207] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.316868] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.326405] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.340060] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.348644] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.357278] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.365834] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.376882] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.396905] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.404974] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.416421] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.425053] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.433696] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.442258] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 8.637150] caam algorithms registered in /proc/crypto <6>[ 8.644121] caam 2100000.crypto: registering rng-caam <4>[ 8.651458] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.665906] panel-simple panel-lcd: supply power not found, using dummy regulator done <4>[ 8.673902] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.685566] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) Saving random seed: <6>[ 8.694141] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.704447] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <5>[ 8.705388] random: dd: uninitialized urandom read (32 bytes read) <6>[ 8.713002] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) OK Starting network: <4>[ 8.741166] panel-simple panel-lvds0: supply power not found, using dummy regulator ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 8.827259] random: dropbear: uninitialized urandom read (32 bytes read) <5>[ 8.834346] random: crng init done <5>[ 8.838018] random: 1 urandom warning(s) missed due to ratelimiting OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-9273474/environment . /lava-9273474/environment / # /lava-9273474/bin/lava-test-runner /lava-9273474/0 /lava-9273474/bin/lava-test-runner /lava-9273474/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-9273474/0/tests/0_dmesg + cat uuid + UUID=9273474_1.5.2.4<8>[ 9.453113] .1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 9.499335] <8>[ 9.540743] <8>[ 9.581962] + set<8>[ 9.592008] +x / # # #export SHELL=/bin/sh / # export SHELL=/bin/sh. /lava-9273474/environment / # . /lava-9273474/environment/lava-9273474/bin/lava-test-runner /lava-9273474/1 / # /lava-9273474/bin/lava-test-runner /lava-9273474/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-9273474/1/tests/1_bootrr + cat uuid + UUID=9273474_1.5.2.4.5<8>[ 10.104851] + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-9273474/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto backlight-lcd backlight-lvds panel-lcd 120000.hdmi panel-lvds0 /lava-9273474/1/../bin/lava-test-case <8>[ 11.188727] /lava-9273474/1/../bin/lava-test-case <8>[ 11.240148] /lava-9273474/1/../bin/lava-test-case <8>[ 11.265239] + set<8>[ 11.283965] +x / #