[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no =>setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.35 (6 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 9410930/tftp-deploy-lr0a_bm6/kernel/zImage tftp 0x10000000 9410930/tftp-deploy-lr0a_bm6/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '9410930/tftp-deploy-lr0a_bm6/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################# 5.2 MiB/s done Bytes transferred = 12345856 (bc6200 hex) => tftp 0x14000000 9410930/tftp-deploy-lr0a_bm6/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 9410930/tftp-deploy-lr0a_bm6/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '9410930/tftp-deploy-lr0a_bm6/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############# 12.4 MiB/s done Bytes transferred = 15456370 (ebd872 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 9410930/tftp-deploy-lr0a_bm6/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 9410930/tftp-deploy-lr0a_bm6/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '9410930/tftp-deploy-lr0a_bm6/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 10.1 MiB/s done Bytes transferred = 42449 (a5d1 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/9410930/extract-nfsrootfs-rs16rxkr,tcp,hard ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/9410930/extract-nfsrootfs-rs16rxkr,tcp,hard ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0xbc6200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 15456306 Bytes = 14.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d5d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.172-cip27 (KernelCI@build-j1120716-arm-gcc-10-multi-v7-defconfig-kselftest-94ncq) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Fri Mar 3 19:26:41 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 21 pages/cpu s55468 r8192 d22356 u86016 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/9410930/extract-nfsrootfs-rs16rxkr,tcp,hard ip=dhcp [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 921428K/1048576K available (17408K kernel code, 2651K rwdata, 8100K rodata, 2048K init, 6691K bss, 61612K reserved, 65536K cma-reserved, 196608K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] ftrace: allocating 55428 entries in 163 pages [ 0.000000] ftrace: allocated 163 pages with 4 groups [ 0.000000] Running RCU self tests [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU lockdep checking is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] L2C-310 errata 752271 769419 enabled [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 [ 0.000000] Switching to timer-based delay loop, resolution 333ns [ 0.000008] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns [ 0.000042] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns [ 0.004477] Console: colour dummy device 80x30 [ 0.004547] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.004578] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.004606] ... MAX_LOCK_DEPTH: 48 [ 0.004635] ... MAX_LOCKDEP_KEYS: 8192 [ 0.004661] ... CLASSHASH_SIZE: 4096 [ 0.004689] ... MAX_LOCKDEP_ENTRIES: 32768 [ 0.004715] ... MAX_LOCKDEP_CHAINS: 65536 [ 0.004742] ... CHAINHASH_SIZE: 32768 [ 0.004769] memory used by lock dependency info: 4061 kB [ 0.004796] memory used for stack traces: 2112 kB [ 0.004822] per task-struct memory footprint: 1536 bytes [ 0.004923] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) [ 0.004976] pid_max: default: 32768 minimum: 301 [ 0.005357] LSM: Security Framework initializing [ 0.005471] LSM support for eBPF active [ 0.005620] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.005672] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.008247] CPU: Testing write buffer coherency: ok [ 0.008384] CPU0: Spectre v2: using BPIALL workaround [ 0.009490] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.013492] Setting up static identity map for 0x10300000 - 0x103000ac [ 0.016014] rcu: Hierarchical SRCU implementation. [ 0.025479] EFI services will not be available. [ 0.026829] smp: Bringing up secondary CPUs ... [ 0.030237] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.030253] CPU1: Spectre v2: using BPIALL workaround [ 0.034340] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.034355] CPU2: Spectre v2: using BPIALL workaround [ 0.038079] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.038094] CPU3: Spectre v2: using BPIALL workaround [ 0.039145] smp: Brought up 1 node, 4 CPUs [ 0.039190] SMP: Total of 4 processors activated (24.00 BogoMIPS). [ 0.039227] CPU: All CPU(s) started in SVC mode. [ 0.041855] devtmpfs: initialized [ 0.099004] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.101774] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.101857] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.106729] pinctrl core: initialized pinctrl subsystem [ 0.113940] DMI not present or invalid. [ 0.116308] NET: Registered protocol family 16 [ 0.128037] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.137845] thermal_sys: Registered thermal governor 'step_wise' [ 0.138401] cpuidle: using governor menu [ 0.139012] CPU identified as i.MX6Q, silicon rev 1.2 [ 0.882801] vdd1p1: supplied by regulator-dummy [ 0.914506] vdd3p0: supplied by regulator-dummy [ 0.945808] vdd2p5: supplied by regulator-dummy [ 0.977136] vddarm: supplied by regulator-dummy [ 1.009358] vddpu: supplied by regulator-dummy [ 1.039672] vddsoc: supplied by regulator-dummy [ 2.367697] No ATAGs? [ 2.368441] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 2.368525] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 2.388963] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver [ 2.419432] Serial: AMBA PL011 UART driver [ 2.484345] Kprobes globally optimized [ 2.605721] iommu: Default domain type: Translated [ 2.607968] vgaarb: loaded [ 2.612929] SCSI subsystem initialized [ 2.615143] usbcore: registered new interface driver usbfs [ 2.615449] usbcore: registered new interface driver hub [ 2.615716] usbcore: registered new device driver usb [ 2.623539] i2c i2c-0: IMX I2C adapter registered [ 2.630690] i2c i2c-1: IMX I2C adapter registered [ 2.635266] i2c i2c-2: IMX I2C adapter registered [ 2.640143] pps_core: LinuxPPS API ver. 1 registered [ 2.640188] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 2.640290] PTP clock support registered [ 2.657448] clocksource: Switched to clocksource mxc_timer1 [ 4.349874] NET: Registered protocol family 2 [ 4.350689] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 4.353988] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 22528 bytes, linear) [ 4.354169] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 4.354406] TCP bind hash table entries: 8192 (order: 6, 327680 bytes, linear) [ 4.355846] TCP: Hash tables configured (established 8192 bind 8192) [ 4.356936] MPTCP token hash table entries: 1024 (order: 3, 49152 bytes, linear) [ 4.357282] UDP hash table entries: 512 (order: 3, 49152 bytes, linear) [ 4.357695] UDP-Lite hash table entries: 512 (order: 3, 49152 bytes, linear) [ 4.358460] NET: Registered protocol family 1 [ 4.361326] RPC: Registered named UNIX socket transport module. [ 4.361423] RPC: Registered udp transport module. [ 4.361466] RPC: Registered tcp transport module. [ 4.361508] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 4.361575] NET: Registered protocol family 44 [ 4.361649] PCI: CLS 0 bytes, default 64 [ 4.364166] Trying to unpack rootfs image as initramfs... [ 6.259145] Freeing initrd memory: 15096K [ 6.260395] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 6.261547] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 6.270981] Initialise system trusted keyrings [ 6.272063] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 6.323947] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 6.328019] NFS: Registering the id_resolver key type [ 6.328199] Key type id_resolver registered [ 6.328293] Key type id_legacy registered [ 6.328956] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 6.329066] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 6.329282] ntfs: driver 2.1.32 [Flags: R/O]. [ 6.331498] Key type asymmetric registered [ 6.331630] Asymmetric key parser 'x509' registered [ 6.332063] bounce: pool size: 64 pages [ 6.332263] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 6.332375] io scheduler mq-deadline registered [ 6.332422] io scheduler kyber registered [ 6.333416] test_firmware: interface ready [ 6.521165] mxs-dma 110000.dma-apbh: initialized [ 6.588976] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 6.589241] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 6.846775] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 6.868171] SuperH (H)SCI(F) driver initialized [ 6.871275] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX [ 6.876556] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX [ 7.808624] printk: console [ttymxc1] enabled [ 7.819758] msm_serial: driver initialized [ 7.824984] STMicroelectronics ASC driver initialized [ 7.836888] STM32 USART driver initialized [ 7.864298] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 0 [ 7.887179] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.895685] panel-simple panel-lcd: Specify missing connector_type [ 7.903613] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.959585] brd: module loaded [ 8.022537] loop: module loaded [ 8.029292] lkdtm: No crash points registered, enable through debugfs [ 8.052300] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 [ 8.060346] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 [ 8.068465] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 [ 8.076685] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 [ 8.084784] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator [ 8.093098] ahci-imx 2200000.sata: supply phy not found, using dummy regulator [ 8.100986] ahci-imx 2200000.sata: supply target not found, using dummy regulator [ 8.112404] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled [ 8.119536] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 8.128435] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 8.143028] scsi host0: ahci-imx [ 8.148782] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 [ 8.216627] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 8.230476] pps pps0: new PPS source ptp0 [ 8.277135] fec 2188000.ethernet eth0: registered PHC device 0 [ 8.288251] e1000e: Intel(R) PRO/1000 Network Driver [ 8.293258] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 8.299520] igb: Intel(R) Gigabit Ethernet Network Driver [ 8.304954] igb: Copyright (c) 2007-2014 Intel Corporation. [ 8.334108] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 8.341764] usbcore: registered new interface driver pegasus [ 8.347733] usbcore: registered new interface driver asix [ 8.353318] usbcore: registered new interface driver ax88179_178a [ 8.359665] usbcore: registered new interface driver cdc_ether [ 8.365748] usbcore: registered new interface driver smsc75xx [ 8.371799] usbcore: registered new interface driver smsc95xx [ 8.377783] usbcore: registered new interface driver net1080 [ 8.383622] usbcore: registered new interface driver cdc_subset [ 8.389823] usbcore: registered new interface driver zaurus [ 8.395686] usbcore: registered new interface driver cdc_ncm [ 8.415058] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 8.421767] ehci-pci: EHCI PCI platform driver [ 8.426414] ehci-platform: EHCI generic platform driver [ 8.432831] ehci-orion: EHCI orion driver [ 8.437896] SPEAr-ehci: EHCI SPEAr driver [ 8.442862] ehci-st: EHCI STMicroelectronics driver [ 8.448752] ehci-exynos: EHCI Exynos driver [ 8.453879] ehci-atmel: EHCI Atmel driver [ 8.458879] tegra-ehci: Tegra EHCI driver [ 8.463862] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 8.470265] ohci-pci: OHCI PCI platform driver [ 8.474927] ohci-platform: OHCI generic platform driver [ 8.481279] SPEAr-ohci: OHCI SPEAr driver [ 8.486240] ohci-st: OHCI STMicroelectronics driver [ 8.492138] ohci-atmel: OHCI Atmel driver [ 8.499917] usbcore: registered new interface driver usb-storage [ 8.500322] ata1: SATA link down (SStatus 0 SControl 300) [ 8.511835] ahci-imx 2200000.sata: no device found, disabling link. [ 8.518200] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug [ 8.540903] i2c /dev entries driver [ 8.632583] sdhci: Secure Digital Host Controller Interface driver [ 8.638859] sdhci: Copyright(c) Pierre Ossman [ 8.653477] Synopsys Designware Multimedia Card Interface Driver [ 8.667490] sdhci-pltfm: SDHCI platform and OF driver helper [ 8.677020] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO [ 8.677027] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO [ 8.677218] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO [ 8.695118] ledtrig-cpu: registered to indicate activity on CPUs [ 8.705332] usbcore: registered new interface driver usbhid [ 8.711053] usbhid: USB HID core driver [ 8.731512] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA [ 8.731565] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA [ 8.741028] ipip: IPv4 and MPLS over IPv4 tunneling driver [ 8.753645] IPv4 over IPsec tunneling driver [ 8.763350] NET: Registered protocol family 10 [ 8.773770] Segment Routing with IPv6 [ 8.779771] mmc2: new high speed SDHC card at address 0001 [ 8.784206] NET: Registered protocol family 17 [ 8.789351] mmcblk2: mmc2:0001 SD 14.6 GiB [ 8.795985] Key type dns_resolver registered [ 8.816568] ThumbEE CPU extension supported. [ 8.820995] Registering SWP/SWPB emulation handler [ 8.829915] Loading compiled-in X.509 certificates [ 8.851429] GPT:Primary header thinks Alt. header is not at the end of the disk. [ 8.859096] GPT:29296874 != 30560255 [ 8.862709] GPT:Alternate GPT header not at the end of the disk. [ 8.868799] GPT:29296874 != 30560255 [ 8.872407] GPT: Use GNU Parted to correct GPT errors. [ 8.877687] mmcblk2: p1 p2 p3 [ 9.018390] panel-simple panel-lcd: supply power not found, using dummy regulator [ 9.026772] panel-simple panel-lcd: Specify missing connector_type [ 9.040406] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 9.077024] imx_usb 2184200.usb: No over current polarity defined [ 9.090484] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 9.095722] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 [ 9.128100] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 9.149389] hub 1-0:1.0: USB hub found [ 9.153737] hub 1-0:1.0: 1 port detected [ 9.170144] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C [ 9.203066] panel-simple panel-lcd: supply power not found, using dummy regulator [ 9.211418] panel-simple panel-lcd: Specify missing connector_type [ 9.224941] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 9.256389] panel-simple panel-lcd: supply power not found, using dummy regulator [ 9.264802] panel-simple panel-lcd: Specify missing connector_type [ 9.278556] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 9.297881] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 9.331260] panel-simple panel-lcd: supply power not found, using dummy regulator [ 9.339641] panel-simple panel-lcd: Specify missing connector_type [ 9.353128] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 9.374662] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) [ 9.557959] usb 1-1: new high-speed USB device number 2 using ci_hdrc [ 9.767196] hub 1-1:1.0: USB hub found [ 9.773132] hub 1-1:1.0: 3 ports detected [ 9.809228] panel-simple panel-lcd: supply power not found, using dummy regulator [ 9.817826] panel-simple panel-lcd: Specify missing connector_type [ 9.833641] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 12.479569] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 12.508145] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 12.537729] Sending DHCP requests ., OK [ 12.582213] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.35 [ 12.590533] IP-Config: Complete: [ 12.593853] device=eth0, hwaddr=00:19:b8:08:f1:09, ipaddr=192.168.201.35, mask=255.255.255.0, gw=192.168.201.1 [ 12.604405] host=imx6q-sabrelite-lava-cbg-5, domain=lava-rack, nis-domain=(none) [ 12.612316] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= [ 12.612335] nameserver0=192.168.201.1 [ 12.673863] Freeing unused kernel memory: 2048K [ 12.688307] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u1 [ 16.694153] imx-ipuv3 2400000.ipu: IPUv3H probed [ 16.759020] panel-simple panel-lcd: supply power not found, using dummy regulator [ 16.778939] panel-simple panel-lcd: Specify missing connector_type [ 16.782486] CAN device driver interface [ 16.790657] imx-ipuv3 2800000.ipu: IPUv3H probed [ 16.809612] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 16.874686] panel-simple panel-lcd: supply power not found, using dummy regulator [ 16.883113] panel-simple panel-lcd: Specify missing connector_type [ 16.896817] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 16.921547] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) [ 16.938756] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) [ 16.946805] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) [ 16.953567] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 [ 16.962171] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 [ 16.968565] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 [ 16.974704] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 [ 16.983814] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 1 [ 17.010189] caam 2100000.crypto: Entropy delay = 3200 [ 17.019753] panel-simple panel-lcd: supply power not found, using dummy regulator [ 17.028686] panel-simple panel-lcd: Specify missing connector_type [ 17.042366] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 17.076069] caam 2100000.crypto: Instantiated RNG4 SH0 [ 17.136831] caam 2100000.crypto: Instantiated RNG4 SH1 [ 17.142106] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) [ 17.148844] caam 2100000.crypto: job rings = 2, qi = 0 [ 17.185475] panel-simple panel-lcd: supply power not found, using dummy regulator [ 17.194260] panel-simple panel-lcd: Specify missing connector_type [ 17.208819] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 17.259221] panel-simple panel-lcd: supply power not found, using dummy regulator [ 17.265539] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator [ 17.267656] panel-simple panel-lcd: Specify missing connector_type [ 17.279554] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) [ 17.287963] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests [ 17.291024] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) [ 17.296038] sgtl5000 0-000a: sgtl5000 revision 0x11 [ 17.297755] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator [ 17.303154] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 17.305970] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) [ 17.309919] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum [ 17.311080] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests [ 17.318435] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) [ 17.352328] panel-simple panel-lcd: supply power not found, using dummy regulator [ 17.366391] panel-simple panel-lcd: Specify missing connector_type [ 17.399330] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 17.490235] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) [ 17.499466] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) [ 17.508156] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) [ 17.516654] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) [ 17.534316] panel-simple panel-lcd: supply power not found, using dummy regulator [ 17.543018] panel-simple panel-lcd: Specify missing connector_type [ 18.148420] caam algorithms registered in /proc/crypto [ 18.161874] caam 2100000.crypto: registering rng-caam [ 18.291156] random: crng init done [ 18.304672] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 18.342883] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) [ 18.351491] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) [ 18.360127] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) [ 18.368598] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) [ 18.383629] panel-simple panel-lcd: supply power not found, using dummy regulator [ 18.393265] panel-simple panel-lcd: Specify missing connector_type [ 18.408415] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 18.446078] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) [ 18.454611] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) [ 18.463486] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) [ 18.471967] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. IP-Config: eth0 hardware address 00:19:b8:08:f1:09 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.35 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-5 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 20.645217] systemd[1]: System time before build time, advancing clock. [ 20.864672] systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) [ 20.895613] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! [ 20.964466] systemd[1]: Set hostname to . [ 22.561031] systemd[1]: Queued start job for default target Graphical Interface. [ 22.574866] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. [ 22.622850] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. [ 22.672852] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 22.722383] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 22.772107] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. [ 22.821357] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. [ 22.869469] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. [ 22.881643] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. [ 22.918268] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. [ 22.958953] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 23.008708] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. [ 23.048047] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 23.093287] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. [ 23.193534] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. [ 23.208235] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 23.254868] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 23.314949] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. [ 23.370456] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 23.423188] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 23.471895] systemd[1]: Condition check resulted in Huge Pages File System being skipped. [ 23.483001] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. [ 23.506267] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... [ 23.549613] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... [ 23.607252] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... [ 23.660601] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... [ 23.721085] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... [ 23.781231] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... [ 23.824589] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. [ 23.859092] systemd[1]: Starting Journal Service... Starting Journal Service... [ 23.874012] fuse: init (API version 7.32) [ 23.916362] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 23.978254] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... [ 24.029393] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... [ 24.110466] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. [ 24.153480] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. [ 24.215853] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. [ 24.297663] systemd[1]: modprobe@configfs.service: Succeeded. [ 24.307880] systemd[1]: Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module configfs. [ 24.363421] systemd[1]: modprobe@drm.service: Succeeded. [ 24.373201] systemd[1]: Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module drm. [ 24.423550] systemd[1]: modprobe@fuse.service: Succeeded. [ 24.434164] systemd[1]: Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Module fuse. [ 24.483070] systemd[1]: Finished Load Kernel Modules. [ OK ] Finished Load Kernel Modules. [ 24.533461] systemd[1]: Finished Remount Root and Kernel File Systems. [ OK ] Finished Remount Root and Kernel File Systems. [ 24.599658] systemd[1]: Mounting FUSE Control File System... Mounting FUSE Control File System... [ 24.648331] systemd[1]: Mounting Kernel Configuration File System... Mounting Kernel Configuration File System... [ 24.696709] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped. [ 24.707052] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped. [ 24.726230] systemd[1]: Starting Load/Save Random Seed... Starting Load/Save Random Seed... [ 24.787854] systemd[1]: Starting Apply Kernel Variables... Starting Apply Kernel Variables... [ 24.841223] systemd[1]: Starting Create System Users... Starting Create System Users... [ 24.886881] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Mounted FUSE Control File System. [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. Starting Flush Journal to Persistent Storage... Starting Create Static Device Nodes in /dev... [ 25.295296] systemd-journald[279]: Received client request to flush runtime journal. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Rule-based Manage…for Device Events and Files... [ OK ] Finished Flush Journal to Persistent Storage. Starting Create Volatile Files and Directories... [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... [ OK ] Finished Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Network Name Resolution. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Finished Coldplug All udev Devices. [ OK ] Reached target System Initialization. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... Starting Permit User Sessions... [ OK ] Found device /dev/ttymxc1. [ OK ] Finished Permit User Sessions. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 5.10.172-cip27 #1 SMP Fri Mar 3 19:26:41 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/9410930/extract-nfsrootfs-rs16rxkr' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/9410930/extract-nfsrootfs-rs16rxkr' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-9410930/environment . /lava-9410930/environment / # /lava-9410930/bin/lava-test-runner /lava-9410930/0 /lava-9410930/bin/lava-test-runner /lava-9410930/0 + export TESTRUN_ID=0_dmesg + cd /lava-9410930/0/tests/0_dmesg + cat uuid + UUID=9410930_1.6.2.4.1[ 44.022787] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh [ 44.287082] [ 44.486647] [ 44.675982] + set +x [ 44.688371] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-9410930/environment / # . /lava-9410930/environment/lava-9410930/bin/lava-test-runner /lava-9410930/1 / # /lava-9410930/bin/lava-test-runner /lava-9410930/1 + export TESTRUN_ID=1_bootrr + cd /lava-9410930/1/tests/1_bootrr + cat uuid + UUID=9410930_1.6.2.4.5[ 45.501247] + set +x + export PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-9410930/1/../bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto panel-lcd panel-lvds0 backlight-lcd backlight-lvds 120000.hdmi /lava-9410930/1/../bin/lava-test-case [ 46.874731] /lava-9410930/1/../bin/lava-test-case [ 47.090031] /lava-9410930/1/../bin/lava-test-case [ 47.190033] + set +x [ 47.265215] / #