[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.0 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected sst25vf016b with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 6 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.101.100 (3 ms) => setenv serverip 192.168.101.1 setenv serverip 192.168.101.1 => tftp 0x10000000 9410934/tftp-deploy-2_x6wh70/kernel/zImage tftp 0x10000000 9410934/tftp-deploy-2_x6wh70/kernel/zImage Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.100 Filename '9410934/tftp-deploy-2_x6wh70/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################# 3 MiB/s done Bytes transferred = 12345856 (bc6200 hex) => tftp 0x14000000 9410934/tftp-deploy-2_x6wh70/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 9410934/tftp-deploy-2_x6wh70/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.100 Filename '9410934/tftp-deploy-2_x6wh70/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############# 2.9 MiB/s done Bytes transferred = 15453060 (ebcb84 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 9410934/tftp-deploy-2_x6wh70/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 9410934/tftp-deploy-2_x6wh70/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.100 Filename '9410934/tftp-deploy-2_x6wh70/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 2.2 MiB/s done Bytes transferred = 42449 (a5d1 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.101.1:/var/lib/lava/dispatcher/tmp/9410934/extract-nfsrootfs-mmfc95pf,tcp,hard console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.101.1:/var/lib/lava/dispatcher/tmp/9410934/extract-nfsrootfs-mmfc95pf,tcp,hard console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0xbc6200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 15452996 Bytes = 14.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d5d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.172-cip27 (KernelCI@build-j1120716-arm-gcc-10-multi-v7-defconfig-kselftest-94ncq) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Fri Mar 3 19:26:41 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 21 pages/cpu s55468 r8192 d22356 u86016 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.101.1:/var/lib/lava/dispatcher/tmp/9410934/extract-nfsrootfs-mmfc95pf,tcp,hard console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 921432K/1048576K available (17408K kernel code, 2651K rwdata, 8100K rodata, 2048K init, 6691K bss, 61608K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] ftrace: allocating 55428 entries in 163 pages <6>[ 0.000000] ftrace: allocated 163 pages with 4 groups <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] Rude variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 15ns <6>[ 0.000008] sched_clock: 32 bits at 66MHz, resolution 15ns, wraps every 32537631224ns <6>[ 0.008096] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 28958491609 ns <6>[ 0.022434] Console: colour dummy device 80x30 <4>[ 0.024342] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.032349] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.036694] ... MAX_LOCK_DEPTH: 48 <4>[ 0.041104] ... MAX_LOCKDEP_KEYS: 8192 <4>[ 0.045740] ... CLASSHASH_SIZE: 4096 <4>[ 0.050326] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.055024] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.059746] ... CHAINHASH_SIZE: 32768 <4>[ 0.064421] memory used by lock dependency info: 4061 kB <4>[ 0.070100] memory used for stack traces: 2112 kB <4>[ 0.075122] per task-struct memory footprint: 1536 bytes <6>[ 0.080856] Calibrating delay loop (skipped), value calculated using timer frequency.. 132.00 BogoMIPS (lpj=660000) <6>[ 0.091511] pid_max: default: 32768 minimum: 301 <6>[ 0.096731] LSM: Security Framework initializing <6>[ 0.101304] LSM support for eBPF active <6>[ 0.105428] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.112936] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.123486] CPU: Testing write buffer coherency: ok <6>[ 0.126063] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.132297] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.141244] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.147785] rcu: Hierarchical SRCU implementation. <6>[ 0.159699] EFI services will not be available. <6>[ 0.162952] smp: Bringing up secondary CPUs ... <6>[ 0.169808] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.169825] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.182270] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.182286] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.194385] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.194399] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.203626] smp: Brought up 1 node, 4 CPUs <6>[ 0.207276] SMP: Total of 4 processors activated (528.00 BogoMIPS). <6>[ 0.213674] CPU: All CPU(s) started in SVC mode. <6>[ 0.221305] devtmpfs: initialized <6>[ 0.278970] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.286844] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.294274] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.306344] pinctrl core: initialized pinctrl subsystem <6>[ 0.316116] DMI not present or invalid. <6>[ 0.319696] NET: Registered protocol family 16 <6>[ 0.333745] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.347877] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.348434] cpuidle: using governor menu <6>[ 0.356622] CPU identified as i.MX6Q, silicon rev 1.0 <6>[ 1.105045] vdd1p1: supplied by regulator-dummy <6>[ 1.138973] vdd3p0: supplied by regulator-dummy <6>[ 1.172224] vdd2p5: supplied by regulator-dummy <6>[ 1.205461] vddarm: supplied by regulator-dummy <6>[ 1.239768] vddpu: supplied by regulator-dummy <6>[ 1.271911] vddsoc: supplied by regulator-dummy <6>[ 2.602065] No ATAGs? <6>[ 2.603002] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 2.610122] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 2.636674] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 2.671418] Serial: AMBA PL011 UART driver <6>[ 2.737955] Kprobes globally optimized <6>[ 2.860406] iommu: Default domain type: Translated <6>[ 2.864785] vgaarb: loaded <5>[ 2.870550] SCSI subsystem initialized <6>[ 2.873828] usbcore: registered new interface driver usbfs <6>[ 2.877868] usbcore: registered new interface driver hub <6>[ 2.883244] usbcore: registered new device driver usb <6>[ 2.896232] i2c i2c-0: IMX I2C adapter registered <6>[ 2.905403] i2c i2c-1: IMX I2C adapter registered <6>[ 2.912211] i2c i2c-2: IMX I2C adapter registered <6>[ 2.919145] pps_core: LinuxPPS API ver. 1 registered <6>[ 2.921551] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 2.931073] PTP clock support registered <6>[ 2.953205] clocksource: Switched to clocksource mxc_timer1 <6>[ 4.651225] NET: Registered protocol family 2 <6>[ 4.653873] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 4.664038] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 22528 bytes, linear) <6>[ 4.670064] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 4.678221] TCP bind hash table entries: 8192 (order: 6, 327680 bytes, linear) <6>[ 4.686877] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 4.693349] MPTCP token hash table entries: 1024 (order: 3, 49152 bytes, linear) <6>[ 4.699983] UDP hash table entries: 512 (order: 3, 49152 bytes, linear) <6>[ 4.706845] UDP-Lite hash table entries: 512 (order: 3, 49152 bytes, linear) <6>[ 4.714654] NET: Registered protocol family 1 <6>[ 4.721252] RPC: Registered named UNIX socket transport module. <6>[ 4.724802] RPC: Registered udp transport module. <6>[ 4.729607] RPC: Registered tcp transport module. <6>[ 4.734649] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 4.741307] NET: Registered protocol family 44 <6>[ 4.746058] PCI: CLS 0 bytes, default 64 <6>[ 4.752581] Trying to unpack rootfs image as initramfs... <6>[ 6.650874] Freeing initrd memory: 15092K <4>[ 6.653323] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 6.660873] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 6.677638] Initialise system trusted keyrings <6>[ 6.680636] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 6.738247] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 6.745678] NFS: Registering the id_resolver key type <5>[ 6.748311] Key type id_resolver registered <5>[ 6.752620] Key type id_legacy registered <6>[ 6.757569] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 6.763967] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 6.771666] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 6.778454] Key type asymmetric registered <5>[ 6.780537] Asymmetric key parser 'x509' registered <6>[ 6.786008] bounce: pool size: 64 pages <6>[ 6.789802] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 6.797469] io scheduler mq-deadline registered <6>[ 6.802120] io scheduler kyber registered <4>[ 6.807384] test_firmware: interface ready <6>[ 6.997787] mxs-dma 110000.dma-apbh: initialized <4>[ 7.067498] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 7.074780] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 7.333583] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 7.358628] SuperH (H)SCI(F) driver initialized <6>[ 7.363711] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 7.375093] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 7.381558] printk: console [ttymxc1] enabled <6>[ 7.381558] printk: console [ttymxc1] enabled <6>[ 7.390452] printk: bootconsole [ec_imx21] disabled <6>[ 7.390452] printk: bootconsole [ec_imx21] disabled <6>[ 7.407329] msm_serial: driver initialized <6>[ 7.412897] STMicroelectronics ASC driver initialized <6>[ 7.425141] STM32 USART driver initialized <6>[ 7.452942] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 0 <4>[ 7.476111] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.484845] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.493060] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.548813] brd: module loaded <6>[ 7.612102] loop: module loaded <6>[ 7.619060] lkdtm: No crash points registered, enable through debugfs <6>[ 7.642261] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 7.650579] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 7.658956] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 7.667502] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 7.675825] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 7.684422] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 7.692405] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 7.704107] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 7.711400] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 7.720592] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 7.735417] scsi host0: ahci-imx <6>[ 7.741333] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 7.809576] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 7.823684] pps pps0: new PPS source ptp0 <6>[ 7.870191] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 7.881395] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 7.886733] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 7.893259] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 7.898959] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 7.928358] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 7.936271] usbcore: registered new interface driver pegasus <6>[ 7.942475] usbcore: registered new interface driver asix <6>[ 7.948382] usbcore: registered new interface driver ax88179_178a <6>[ 7.954989] usbcore: registered new interface driver cdc_ether <6>[ 7.961337] usbcore: registered new interface driver smsc75xx <6>[ 7.967651] usbcore: registered new interface driver smsc95xx <6>[ 7.973899] usbcore: registered new interface driver net1080 <6>[ 7.979999] usbcore: registered new interface driver cdc_subset <6>[ 7.986447] usbcore: registered new interface driver zaurus <6>[ 7.992589] usbcore: registered new interface driver cdc_ncm <6>[ 8.012224] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 8.019190] ehci-pci: EHCI PCI platform driver <6>[ 8.024144] ehci-platform: EHCI generic platform driver <6>[ 8.030756] ehci-orion: EHCI orion driver <6>[ 8.036087] SPEAr-ehci: EHCI SPEAr driver <6>[ 8.041310] ehci-st: EHCI STMicroelectronics driver <6>[ 8.047463] ehci-exynos: EHCI Exynos driver <6>[ 8.052899] ehci-atmel: EHCI Atmel driver <6>[ 8.058104] tegra-ehci: Tegra EHCI driver <6>[ 8.063414] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 8.069970] ohci-pci: OHCI PCI platform driver <6>[ 8.074944] ohci-platform: OHCI generic platform driver <6>[ 8.081481] SPEAr-ohci: OHCI SPEAr driver <6>[ 8.086823] ohci-st: OHCI STMicroelectronics driver <6>[ 8.092981] ohci-atmel: OHCI Atmel driver <6>[ 8.095536] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 8.101058] usbcore: registered new interface driver usb-storage <6>[ 8.103370] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 8.115975] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 8.144343] i2c /dev entries driver <6>[ 8.235948] sdhci: Secure Digital Host Controller Interface driver <6>[ 8.242433] sdhci: Copyright(c) Pierre Ossman <6>[ 8.257366] Synopsys Designware Multimedia Card Interface Driver <6>[ 8.271534] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 8.281397] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 8.281405] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 8.281590] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 8.298973] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 8.309548] usbcore: registered new interface driver usbhid <6>[ 8.315531] usbhid: USB HID core driver <6>[ 8.337253] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 8.345637] ipip: IPv4 and MPLS over IPv4 tunneling driver <6>[ 8.345851] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 8.354224] IPv4 over IPsec tunneling driver <6>[ 8.368471] NET: Registered protocol family 10 <6>[ 8.379302] Segment Routing with IPv6 <6>[ 8.390016] NET: Registered protocol family 17 <5>[ 8.397060] Key type dns_resolver registered <6>[ 8.415621] ThumbEE CPU extension supported. <5>[ 8.420231] Registering SWP/SWPB emulation handler <5>[ 8.427181] Loading compiled-in X.509 certificates <4>[ 8.661634] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.670561] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.678826] mmc2: new high speed SDHC card at address 0001 <4>[ 8.686769] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.689082] mmcblk2: mmc2:0001 SD 14.6 GiB <4>[ 8.733570] imx_usb 2184200.usb: No over current polarity defined <6>[ 8.748497] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 8.754388] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <4>[ 8.767321] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 8.775252] GPT:29296874 != 30560255 <4>[ 8.779131] GPT:Alternate GPT header not at the end of the disk. <4>[ 8.785508] GPT:29296874 != 30560255 <4>[ 8.789383] GPT: Use GNU Parted to correct GPT errors. <6>[ 8.793009] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 8.794936] mmcblk2: p1 p2 p3 <6>[ 8.808222] hub 1-0:1.0: USB hub found <6>[ 8.812961] hub 1-0:1.0: 1 port detected <3>[ 8.830967] imx_thermal 20c8000.anatop:tempmon: invalid sensor calibration data <3>[ 8.838658] imx_thermal 20c8000.anatop:tempmon: error -EINVAL: failed to init from nvmem <4>[ 8.847373] imx_thermal: probe of 20c8000.anatop:tempmon failed with error -22 <4>[ 8.881381] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.890419] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.906554] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.945003] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.953879] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.969785] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.993993] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 9.031465] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.040289] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.056228] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 9.080799] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:06: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:06, irq=POLL) <6>[ 9.253430] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 9.463034] hub 1-1:1.0: USB hub found <6>[ 9.468019] hub 1-1:1.0: 3 ports detected <4>[ 9.506035] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.514823] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.530720] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 11.204901] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx <6>[ 11.233640] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 11.263355] Sending DHCP requests ., OK <6>[ 11.307824] IP-Config: Got DHCP answer from 192.168.101.1, my address is 192.168.101.100 <6>[ 11.316460] IP-Config: Complete: <6>[ 11.320038] device=eth0, hwaddr=0e:cc:7b:b0:7c:c7, ipaddr=192.168.101.100, mask=255.255.255.0, gw=192.168.101.1 <6>[ 11.331102] host=imx6q-sabrelite-cbg-1, domain=lava.cbg.collabora.co.uk, nis-domain=(none) <6>[ 11.340265] bootserver=192.168.101.1, rootserver=192.168.101.1, rootpath= <6>[ 11.340313] nameserver0=192.168.101.1 <6>[ 11.422658] Freeing unused kernel memory: 2048K <6>[ 11.434000] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u1 <6>[ 16.425413] imx-ipuv3 2400000.ipu: IPUv3H probed <4>[ 16.463961] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 16.472777] panel-simple panel-lcd: Specify missing connector_type <6>[ 16.496999] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 16.524374] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 16.586053] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 16.594960] panel-simple panel-lcd: Specify missing connector_type <6>[ 16.631255] CAN device driver interface <4>[ 16.633920] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 16.700828] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <4>[ 16.714238] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 16.723209] panel-simple panel-lcd: Specify missing connector_type <6>[ 16.730543] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <4>[ 16.745940] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 16.756588] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 16.763625] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 16.773474] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 16.782738] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 16.789376] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 16.803217] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 1 <6>[ 16.817405] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.826649] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <4>[ 16.828698] panel-simple panel-lcd: supply power not found, using dummy regulator <6>[ 16.833381] caam 2100000.crypto: Entropy delay = 3200 <6>[ 16.835885] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <4>[ 16.844149] panel-simple panel-lcd: Specify missing connector_type <6>[ 16.849049] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.894202] caam 2100000.crypto: Instantiated RNG4 SH0 <4>[ 16.899153] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 16.954964] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 16.960439] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 16.967430] caam 2100000.crypto: job rings = 2, qi = 0 <4>[ 16.986440] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 17.020618] panel-simple panel-lcd: Specify missing connector_type <4>[ 17.069904] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 17.073005] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 17.086832] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 17.109525] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 17.123852] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <6>[ 17.170133] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 17.179605] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 17.188547] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 17.197448] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <6>[ 17.216099] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 17.231571] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <4>[ 17.247782] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 17.257928] panel-simple panel-lcd: Specify missing connector_type <4>[ 17.284461] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 17.336580] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 17.345535] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 17.354445] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 17.363235] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 17.380994] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 17.390072] panel-simple panel-lcd: Specify missing connector_type <4>[ 17.413346] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 18.203838] caam algorithms registered in /proc/crypto <6>[ 18.221135] caam 2100000.crypto: registering rng-caam <6>[ 18.243320] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 18.252089] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 18.260947] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 18.269715] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 18.286959] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 18.295923] panel-simple panel-lcd: Specify missing connector_type <4>[ 18.312523] panel-simple panel-lvds0: supply power not found, using dummy regulator Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available <5>[ 18.410700] random: crng init done Device /sys/class/net/eth0 found done. IP-Config: eth0 hardware address 0e:cc:7b:b0:7c:c7 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.101.1): address: 192.168.101.100 broadcast: 192.168.101.255 netmask: 255.255.255.0 gateway: 192.168.101.1 dns0 : 192.168.101.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-cbg-1 domain : lava.cbg.collabora.co.uk rootserver: 192.168.101.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 21.651245] systemd[1]: System time before build time, advancing clock. <30>[ 21.922973] systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 21.950005] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! <30>[ 22.010419] systemd[1]: Set hostname to . <30>[ 23.979419] systemd[1]: Queued start job for default target Graphical Interface. <30>[ 23.995997] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. <30>[ 24.035892] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. <30>[ 24.078767] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. <30>[ 24.128059] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. <30>[ 24.177578] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. <30>[ 24.226852] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. <30>[ 24.274907] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 24.289165] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. <30>[ 24.334736] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. <30>[ 24.374090] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. <30>[ 24.413966] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. <30>[ 24.455133] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. <30>[ 24.495422] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. <30>[ 24.598191] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. <30>[ 24.617466] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). <30>[ 24.670354] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. <30>[ 24.730246] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. <30>[ 24.785839] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. <30>[ 24.841463] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. <30>[ 24.888503] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 24.900089] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. <30>[ 24.923898] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... <30>[ 24.976034] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... <30>[ 25.027246] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... <30>[ 25.086530] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... <30>[ 25.139240] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... <30>[ 25.189814] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... <30>[ 25.244057] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. <30>[ 25.279694] systemd[1]: Starting Journal Service... <6>[ 25.287784] fuse: init (API version 7.32) Starting Journal Service... <30>[ 25.387046] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... <30>[ 25.446147] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... <30>[ 25.505996] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... <30>[ 25.577536] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. <30>[ 25.617328] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. <30>[ 25.676059] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. <30>[ 25.782407] systemd[1]: modprobe@configfs.service: Succeeded. <30>[ 25.794875] systemd[1]: Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module configfs. <30>[ 25.840458] systemd[1]: modprobe@drm.service: Succeeded. <30>[ 25.852192] systemd[1]: Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module drm. <30>[ 25.900343] systemd[1]: modprobe@fuse.service: Succeeded. <30>[ 25.912177] systemd[1]: Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Module fuse. <30>[ 25.960361] systemd[1]: Finished Load Kernel Modules. [ OK ] Finished Load Kernel Modules. <30>[ 26.000223] systemd[1]: Finished Remount Root and Kernel File Systems. [ OK ] Finished Remount Root and Kernel File Systems. <30>[ 26.058422] systemd[1]: Mounting FUSE Control File System... Mounting FUSE Control File System... <30>[ 26.105304] systemd[1]: Mounting Kernel Configuration File System... Mounting Kernel Configuration File System... <30>[ 26.184884] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped. <30>[ 26.195248] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped. <30>[ 26.216484] systemd[1]: Starting Load/Save Random Seed... Starting Load/Save Random Seed... <30>[ 26.275442] systemd[1]: Starting Apply Kernel Variables... Starting Apply Kernel Variables... <30>[ 26.328077] systemd[1]: Starting Create System Users... Starting Create System Users... <30>[ 26.392691] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Mounted FUSE Control File System. [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. Starting Flush Journal to Persistent Storage... [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... <46>[ 26.829536] systemd-journald[272]: Received client request to flush runtime journal. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Rule-based Manage…for Device Events and Files... [* ] (1 of 4) A start job is running for /dev/ttymxc1 (5s / 1min 30s) M [ OK ] Finished Flush Journal to Persistent Storage.  Starting Create Volatile Files and Directories... [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... [ OK ] Finished Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Finished Coldplug All udev Devices. [ OK ] Reached target System Initialization. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Started Network Name Resolution. [ OK ] Found device /dev/ttymxc1. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [** ] A start job is running for User Login Management (14s / 1min 40s) M [*** ] A start job is running for User Login Management (14s / 1min 40s) M [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 5.10.172-cip27 #1 SMP Fri Mar 3 19:26:41 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/9410934/extract-nfsrootfs-mmfc95pf' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/9410934/extract-nfsrootfs-mmfc95pf' / # export NFS_SERVER_IP='192.168.101.1' export NFS_SERVER_IP='192.168.101.1' / # # # / # export SHELL=/bin/bash export SHELL=/bin/bash / # . /lava-9410934/environment . /lava-9410934/environment / # /lava-9410934/bin/lava-test-runner /lava-9410934/0 /lava-9410934/bin/lava-test-runner /lava-9410934/0 + export TESTRUN_ID=0_timesync-off + TESTRUN_ID=0_timesync-off + cd /lava-9410934/0/tests/0_timesync-off ++ cat uuid + UUID=9410934_1.6.2.4.1 + set +x + systemctl stop systemd-timesyncd + set +x + export TESTRUN_ID=1_kselftest-lib + TESTRUN_ID=1_kselftest-lib + cd /lava-9410934/0/tests/1_kselftest-lib ++ cat uuid + UUID=9410934_1.6.2.4.5 + set +x + cd ./automated/linux/kselftest/ + ./kselftest.sh -c lib -T '' -t kselftest_armhf.tar.gz -s True -u http://storage.kernelci.org/cip-gitlab/ci-iwamatsu-linux-5.10.y-cip-rc/v5.10.168-cip27-109-g23841ec76bec/arm/multi_v7_defconfig+kselftest/gcc-10/kselftest.tar.xz -L '' -S skipfile-lkft.yaml -b imx6q-sabrelite -g cip-gitlab -e '' -p /opt/kselftests/mainline/ -n 1 -i 1 INFO: Generating a skipfile based on /lava-9410934/0/tests/1_kselftest-lib/automated/linux/kselftest/skipfile-lkft.yaml INFO: Using the following generated skipfile contents (until EOF): breakpoints:breakpoint_test breakpoints:step_after_suspend_test ftrace:ftracetest net:rtnetlink.sh net:tls netfilter:bridge_brouter.sh netfilter:nft_flowtable.sh netfilter:nft_trans_stress.sh pidfd:pidfd_wait INFO: EOF INFO: install_deps skipped --2023-03-03 19:44:30-- http://storage.kernelci.org/cip-gitlab/ci-iwamatsu-linux-5.10.y-cip-rc/v5.10.168-cip27-109-g23841ec76bec/arm/multi_v7_defconfig+kselftest/gcc-10/kselftest.tar.xz Resolving storage.kernelci.org (storage.kernelci.org)... 52.250.1.28 Connecting to storage.kernelci.org (storage.kernelci.org)|52.250.1.28|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1408496 (1.3M) [application/octet-stream] Saving to: 'kselftest.tar.xz' kselftest.tar.xz 0%[ ] 0 --.-KB/s kselftest.tar.xz 3%[ ] 50.15K 175KB/s kselftest.tar.xz 15%[==> ] 218.91K 383KB/s kselftest.tar.xz 30%[=====> ] 417.81K 486KB/s kselftest.tar.xz 59%[==========> ] 824.13K 717KB/s kselftest.tar.xz 100%[===================>] 1.34M 1.01MB/s in 1.3s 2023-03-03 19:44:32 (1.01 MB/s) - 'kselftest.tar.xz' saved [1408496/1408496] skiplist: ======================================== breakpoints:breakpoint_test breakpoints:step_after_suspend_test ftrace:ftracetest net:rtnetlink.sh net:tls netfilter:bridge_brouter.sh netfilter:nft_flowtable.sh netfilter:nft_trans_stress.sh pidfd:pidfd_wait ======================================== lib:printf.sh lib:bitmap.sh lib:prime_numbers.sh lib:strscpy.sh ============== Tests to run =============== lib:printf.sh lib:bitmap.sh lib:prime_numbers.sh lib:strscpy.sh ===========End Tests to run =============== <12>[ 66.026091] kselftest: Running tests in lib TAP version 13 1..4 # selftests: lib: printf.sh <6>[ 66.400728] test_printf: loaded. <6>[ 66.407521] test_printf: all 384 tests passed <6>[ 66.466393] test_printf: unloaded. # printf: ok ok 1 selftests: lib: printf.sh # selftests: lib: bitmap.sh <6>[ 66.879036] test_bitmap: loaded. <3>[ 66.883636] test_bitmap: parselist: 14: input is '0-2047:128/256' OK, Time: 4606 <6>[ 66.907777] test_bitmap: all 1679 tests passed <6>[ 66.965833] test_bitmap: unloaded. # bitmap: ok ok 2 selftests: lib: bitmap.sh # selftests: lib: prime_numbers.sh <6>[ 68.105830] prime numbers: selftest(65536) passed, last prime was 65521 # prime numbers: ok ok 3 selftests: lib: prime_numbers.sh # selftests: lib: strscpy.sh <6>[ 68.553596] test_strscpy: loaded. <6>[ 68.557237] test_strscpy: all 32 tests passed <6>[ 68.613295] test_strscpy: unloaded. # strscpy*: ok ok 4 selftests: lib: strscpy.sh lib_printf_sh pass lib_bitmap_sh pass lib_prime_numbers_sh pass lib_strscpy_sh pass + ../../utils/send-to-lava.sh ./output/result.txt + set +x / #